Log into your Prepaway Account
Please Log In to download ETE file or view Training Course
Registration is free and easy - just provide your E-mail address.
Click Here to Register
Exam: | 640-875 - Building Cisco Service Provider Next-Generation Networks, Part 1 (SPNGN1) |
Size: | 471.58 KB |
Posted: | Friday, October 20, 2017 |
Download:
|
|
Log in to make your opinion count.
Registration is free and easy - just provide your E-mail address.
Click Here to Register
Use Discount Code:
A confirmation link was sent to your e-mail.
Please check your mailbox for a message from [email protected] and follow the directions.
Simulation equal to seabass comment.
Something like 15 D&D questions:
- ASR show config commands
- ASR commit commands
- DNS codes (A,AAAA,CNAME,ISDN, etc)
This dump is 90% valid
tnx
Many drag and drop question does not appear in the dumps i would suggest to read:
Ipv6 special address ( example: unicast/Multicast/Link local/Unique Address)
class A/B/C/Multicast address
WAN/LAN Description
Spanning Tree
Routing Protocol (RIPv2/RIPng/OSPF/EIGRP/BGP and IGP/EGP)
IOS XR commit and show commands
Description of Access/Distribution and Core networks
Description of CIDR/VLSM/Subnetting and Route Summarization
The simulation is exactly as seabass have mentioned.
A brief and good study link for IOS XR
http://networkgeekstuff.com/networking/cisco-ios-xr-complete-getting-started-examples-guide/
http://www.cisco.com/web/learning/exams/list/spngn1.html#~Topics
it also miss the 2 labs.. the tolopogy lab is really time consuming.
1. Configure the IPv4 and IPv6 address on the Loopback0 and the gi0/0/0/0 interface. Refer to the topology diagram for the IP addresses to use.
2. Configure EIGRP AS 1 for both IPv4 and IPv6 routing.
3. After successfully completing all the above configurations, you should be able to suuccessfully ping the IPv4 and IPv6 loopback addresses of the CE5 router. Only the Loopbacks of CE5 can be pinged. The physical interfaces of CE5 router cannot be pinged in this simulation.
4. The management interface (MgmtEth0/RSP0/CPU0/0) IPv4 address has been preconfigured and there is no need to enable EIGRP on the management interface."
Solution:
enable
config t
interface loopback0
ipv4 address 10.5.1.1/32
ipv6 address 2001:db8:10:5:1::1/128
no shut
commit
interface gi0/0/0/0
ipv4 address 192.168.105.50/24
ipv6 address 2001:DB8:192:168:105::50/64
no shut
commit
router eigrp 1
address-family ipv4
interface loopback0
interface gi0/0/0/0
address-family ipv6
interface loopback0
interface gi0/0/0/0
commit
*Verify by pining the IPv4 and IPv6 loopback IP addresses of CE5*
The hotspot is is this: "Three topology maps are shown. Using the appropriate show commands, map out the network to identify the correct topology map. Once you determine the correct network topology, answer the four multiple choice questions" Basically, you have to answer four multiple choice questions after using "show cdp neighbors" to determine which devices are connected to other devices. Much like the hotspot for CCNA, except you have to choose the topology out of three choices before answering the questions.
- I get more than 12 drag and drop question about PPPOE messages, DNS records and a lot of IOS-XR drag and drop questions.
- simulation about CDP.
I advise to read the Cisco IOS XR Fundamentals.
good luck
And the simulation was about EIGRP ipv4+ipv6 in a IOS-XR router by the way.