Log into your Prepaway Account
Please Log In to download ETE file or view Training Course
Registration is free and easy - just provide your E-mail address.
Click Here to Register
Exam: | 300-115 - CCNP Cisco IP Switched Networks (SWITCH v2.0) |
Size: | 3.26 MB |
Posted: | Saturday, September 9, 2017 |
Download:
|
Cisco.Pass4sures.300-115.v2017-09-09.by.claire.164q.ete |
Download Free 300-115 Exam Questions |
Log in to make your opinion count.
Registration is free and easy - just provide your E-mail address.
Click Here to Register
Use Discount Code:
A confirmation link was sent to your e-mail.
Please check your mailbox for a message from [email protected] and follow the directions.
Passed today 875/1000
All questions valid from 191 premimum
Passing score is 790
Used only 191Q -100% VALID
40 Questions
Labs: STP-LACP & HSRP & dot1x
I would like to know if i must take ete simulator ?
I can learn just with pdf ?
thanks
PASSED Today
853/1000 Passing score is 790
194Q -100% VALID
40 Questions
Labs:AAA_dot1x-LACP_STP
sim : HSRP
good luck
HSRP sim , labs AAA , Lacp
Labs: LACP,HSRP,AAADot1x, CDP-LLDP Drag and drop.
In LACP i was able toping the router succesfully. Pls make sure you apply all the config on Physical interface only as in the instruction its clearly mentioned in BOLD to apply it on physical interface.
in my case both in both switch vlan 1 was already configured with the ip address and vlan 11,12,13 was already present on switchA.
? and Tab works perfectly in exam.
Make sure to save the config at the end of the sim (copy run start)
all question from 194q
Good luck Everyone
could anyone tell me how to get the 191q. writing the exam in a week.. Much appreciated.
thanks guys
LAB : AAA_Dot1x, LACP_STP.
Sim : HSRP.
Drag and Drop : LLDP_CDP.
Thanks Prepaway very much, thanks all for shared information. Good Luck!
895/1000 yesterday 26.11.2017
Passing score is 790
Used only 191Q -100% VALID
40 Questions
Labs: STP-LACP
Labs need to be check before attempt what i found lots of mistakes ... i.e radius server host IP was wrong, IP's in the Topologies was also wrong so please rectify the dumps before attempt.
LABs:
LACP_STP --- server ip issue and interface range command is not working.
Multilayer Topology IP's was wrong.
exam 194q by.Avinash
exam 164q by.JvD
exam ????
Please advice guys i have exam in a week.
the 191q is the dump ETE File , find it on the side of the page
40 questions
1 simlet- 4 parts
2 simulations - Dot1x and LACP/STP
191Q is still valid.
Re certified and happy. Good luck to all.
Can any one confirm that the 191q is 100% valid.
And it has all the simulations are valid exam simulations are their ?
Thx ..
Is thr any alternet way to open ete throught online?
LABS: AAA,LACP-STP
Sim: HSRP
Drag/DRROP: CDP/LDP Good luck
interface Port-channel 1
switchport mode trunk
switchport trunk encapsulation dot1q
spanning-tree allowed vlans 1,21-23
Is 191q Valid ?
Is anyone here that can share a real experience?
(PS: in order to comment I have to rate the file, strange again)
191Q still valid in Egypt
Labs: AAAdot1x, LACP with STP
Sim: HSRP
Drag&Drop: CDP/LLDP
Please comment what is 191q ?
Please help me
937/1000 Passing score is 790
191Q -100% VALID
40 Questions
Labs: HSRP-AAA_dot1x-LACP_STP
194q still valid. Same questions and labs.
Thank Certprepare.
Can any one confirm that the 191q is still valid.?
i see no one is helping here please help. and how to use with ete file please help, all seem to be ignoring the question how to get hold of 191 dumps????
i passed yesterday
labs : aaa , lacp-stp
sim : hsrp
drag and drop : dcp lldp
? and tap worked perfectly
copy run start is working
good luck and thank you prepaway :)
All questions from 191 premimum dump. LAB AAAdot1x, LACP-STP
Sims HSRP WITH 4 Routers,
and CDP/LLDP Drag and Drop.
Good Luck
Passd today 937/1000
LABs: aaa dot1x/ LACP/
Only show HSRP
Simul : HSRP WITH 4 Routers Drag&Drop : CDP&LLDP . But I think there are few wrong answers in dump cuz I got 958 scores. thus I think 191Q dump is 98 percent accurate. thank you. hit the book!!!
i try with a+ ete player 5.5 and 5.7.4 without success.
very urgent thanks.
HSRP sim
LACP_STP & DOT1X lab
@ Tulk Canada - yes you have to explicitly allow the native vlan with the vlan allowed 21-23,99 command
Q191 is still valid
the 191 dump file is still valid, however there is something to say regarding question 99 (the lab with 2 switches)
the VTP mode on switch B is differ from Switch A, on the exam I had to change it to transparent as the VTP mode of Switch A was transparent.
SwitchB(config)# vtp mode transparent
I do advice to check the question one by one, I did for some of them and found correct, however you should be more than meticulous before going to the exam.
and here is one of my checking:-
Which option is the minimum number of bindings that the DHCP snooping database can store?
A. 1000 bindings
B. 2000 bindings
C. 5000 bindings
D. 8000 bindings
Answer: D
The correct answer is 2000, B should be the correct answer, check it out:-
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/4_1/nx-os/security/configuration/guide/sec_nx-os-cfg/sec_dhcpsnoop.html
theres no ques came out of 191 dump
for each interface u should apply no shut
when u config int command we were using int range f0/3 -4 but in examp use f0/3 - 4 to accepted ur command
in aaa lab in router A command swichport trunk encapsulation dot1q it doesnt accepted put in router B its worked propaly so make it
All questions from 191 premimum dump. LAB AAAdot1x, LACP-STP
Sims HSRP WITH 4 Routers,
and CDP/LLDP Drag and Drop.
Good Luck for all
L1 98%
Infrastructure Security 100%
Infrastructure Services 100%
LAB: LACP_STP, AAA_dot1x & HSRP
IN LACP_STP, I configured trunk and etherchannel at physical interface (#interface range 0/3 – 4) and only “no shutdown” comamnd under port-channel.
I didn’t face any issue. I observed that etherchannel formed properly from the output of #sh etherchannel 1 port-channel and able to ping from SW B to router.
int vlan 1 with ip address was there ready. can see it from sh run.
Good Luck
But I had the problem with
command switch port mode trunk on Sw-A. I put it on port channel but that command wasn't applied on interfaces in bundle f0/3 and 4. I had to directly shoot switchport mode trunk on those interfaces.
In other way trunk on portchannel wont work.
You should carefully pass through running conf, before hit the next button.
you could do add vlan 99
spanning-tree allowed vlans 1,21-23,99
its native vlan and should be on trunk.
I passed 1000/1000
Drag/Drop: CDP/LLDP
Studied 191q
Questions seems to be tough. Some questions were new. Finally passed with 790/1000 yesterday 25.11.2017.
40 Questions. Passing score is 790.
All questions from 191 premimum dump. LAB were HSRP, AAA, LACP-STP and CDP/LLDP Drag and Drop.Good Luck
I found it really funny :)
instead of just keep bragging about 191, post it here, don't just say "Hey 191 is still valid, I passed it today"..Funny :D
98% in L2
100% security
100% service
Lab-LACP_STP, AAA and HSRP
In LACP, trunk and etherchannel are configured at physical interface, # interface range fa0/3 - 4. no need to configure anything except(no shutdown)at the port-channel as "all commands must be entered at the physical interface level" is mentioned in the scenario.
i passed yesterday score 895
Exam 191 still valid and Labs (dot1x , LACP-STP and HSRP with 4 routers)and CDP/LLDP Drag and Drop.
Good Luck for all
with 191q :)
Can you explain LAB LACP_STP. In decision we are allowed vlan 1,21-23, but what about native vlan 99. Is it should allowed ?
191 q still valid 40 question
Sim : HSRP
LAB : AAA_Dot1x, LACP_STP
Drag and Drop : LLDP CDP
A. They remain up, but they are reassigned to the default VLAN.
B. They go down until they are reassigned to a VLAN.
C. They go down, but they are reassigned to the default VLAN.
D. They remain up, but they are reassigned to the native VLAN.
This question... I have tried it in a Cat3750 series switch... the port remains up protocol up so I do not think this is correct (as it says the correct answer is B).
191 Q still valid
LACP, Dot1x, HSRP,LLDP&CDP drag and drop
could anyone tell me how to get the 191q. writing the exam in a week.. Much appreciated.
thanks guys
dump [191q] is very valid; No new questions.
Labs were:
FHRP: HSRP
802.1x (AAA)
vLANs and Trunking with LACP.
Best of luck to all!
i got some issues in laps dont know why !!
Sim : HSRP
LAB : AAA_Dot1x, LACP_STP
Drag and Drop : LLDP CDP
191q Valid
Links: ************
It's the 300-115 dump ETE File at the start of the page which you can download paying 49.99 USD.
Can you please let me know whats the difference between 194q by Avinash and 191q?
Please advice guys i have exam in a week.
LABs: AAAdot1x ,LACP-STP, Sims HSRP WITH 4 Routers and CDP/LLDP Drag and Drop.
Thanks
Labs: AAAdot1x, LACP with STP
Sim: HSRP
Drag&Drop: CDP/LLDP
Labs have some tweaks so read and understand carefully. Goodluck!
thks jon
from Saudi Arabia
Please see the link on the right titled ' how to open ETE' files. these 191q ete file refers to a paid file that avaialble on the top of the page for 49.99 USD.
For those asking how to do LACP - truth be told you should really undrestand the technology and the cli commands. I've done the CCIe written and quite honestly while you may use the questions to prepare the simulations here are a god representation of the real world.
Good luck to alla
191 Q still stands valid.Cleared exam an hour ago.Labs : Configure SW A & B & AAA dot1Q.
Cleared with 979
Is the answers to the sims 100% accurate in the 191 dump?
Please advise
For those who did the exam these days, is the 191q dump is 100% valid? And what about the Lab?
I'll take the exam tomorrow, please someone who kindly reply to my post
Thanks in advance
I'm confused, if I again write exam I'll write the same one.. So I don't know where I went wrong.. Please anyone help.
Yes, the same the LACP
SW-A(config)#vlan 21
SW-A(config-vlan)#name Marketing
SW-A(config-vlan)#exit
SW-A(config)#vlan 22
SW-A(config-vlan)#name Sales
SW-A(config-vlan)#exit
SW-A(config)#vlan 23
SW-A(config-vlan)#name Engineering
SW-A(config-vlan)#exit
A. 1000 bindings
B. 2000 bindings
C. 5000 bindings
D. 8000 bindings
Answer: D
The correct answer is 8000 bindings. You can confirm it here by yourself
DHCP Snooping Configuration Restrictions
When configuring DHCP snooping, note these restrictions:
•The DHCP snooping database stores at least 8,000 bindings
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/12-2SX/configuration/guide/book/snoodhcp.html
passed today.
Good luck
labs VTPv3, LACP-STP, AAAdot1x
In lab you need to configure the new vlan in the switch A also. also the vtp mode and stp mode of switch B should be same as that of switch A. dot1x encapsulation need to be configured in the switch trunk interface. port channel should be properly configured in the switch A. in the dumps these are not configured. during the exam please make sure that the port channel is up. Security lab question the dump answer is the correct one.All the best..
Few new questions – how many dhcp bindings can a switch store ? what information does a subordinate switch in a switch stack keep ? question on etherchannel misconfiguration, one switch is configured with MST but other(client) not then how will it automatically downloads the config from other server switch ? access switch does not become root – set priority higher, IP Source Guard works at which layer ? CDP/LLDP drag and drop ? question on bidirectional flow from switch stacking - correct ans is 32gbps ..
Labs: AAAdot1x, LACP with STP
Sim: HSRP
Drag
i used only Serg-182q.
a few questions which I have not seen before.
labs lacp, dot1x, hsrp.
HSRP, AAA, LACP-STP.
191Q still valid
LAB dot1x , HSRP , LACP
--Shabbir, Adelaide
Thanks
Where can we get the 191q you are talking about.
Please make it available for everyone
Thanks
You can "show cdp neighbors detail" on switch A and you will be able to see the IP address of the RouterA.
What should be the full configuration for VTP and STP mode which is not available in the dumps??????????
Thanks in advance ..
Thanks
what is the issue with configuration saving confused?? how to save the configuration pllzzz do needful
The files are not opening in the A + program ETE someone is having the same problem? Could you tell me what the right software to open.
All questions from 191, HSRP, AAA, LACP-STP.
Tab+? Work in sims
Only 9 questions from dump and 31 new questions. Labs are ok!
I suppongo that If you study and think on the questions carefully during the exam there will be no problems. Learning only dumps is not a way!!!
3 labs - aaa, vlan and HSRP
40 questions in the test, 10-15 questions was from dumbs.
LABS are okey. be careful - i Need the actually dumbs!
Current passing score is 790.
Can you please tell me what's the wrong questions and what's the correct answer
Thanks and congrats for passing
Sorry, the below answer regarding the DHCP snooping database was accidentally picked from NX-OS, someone need to check it for IOS.
Dumps still valid, both JvD and Galvin.
Simlets: VTPv3 and Ferris.
Labs: LACP with STP, AAAdot1x from certprepare.com
There were no drag and drop questions.
pdf format send me please
[email protected]
Labs, (AAA, Ferris, HSRP hotspot and LACP with STP)
careful with sim as IPs are different and keep use of show commands to verify your work, i also was unable to use #copy run start in both sim, but it worked fine and i got the mark.
i passed today score 979
Exam 191 still valid and Labs (dot1x , LACP and HSRP sim)
thank you in advance
[email protected]
could you please confirm and provide us with valid dump
thanks
191Q still valid
Could you send me please the current exam?
If possible send to: [email protected]
I thank you.
HI,How are you doing there.I think you are studying these dumps in more depth.Glad to see that some one is not just reciting the things but trying to understand concepts.I am also reading through stuff but don't have dumps so will you be kind to send me ETE dumps on my mail ID - [email protected]
com
I have passed exam yesterday with score 979.
Layer 2 - 98%
Infrastructure security - 100%
Infrastructure services - 100%
This was my second try. First time I had problem with lab simulations, but fortunately Cisco provided me with complimentary voucher for second try.
I have used only JvD dump, there are 2 or 3 wrong answers in it - they were discussed here in comments.
I have used certprepare.com for labs. I got AAAdot1x lab and LACP with STP lab. Some changes in configs, provided by certprepare were needed, but everything is discussed in comments there.
Keep in mind that #write and #copy running-config startup-config are not available in both labs. There is no need to save your work using these commands.
Thanks to prepaway.com and to all people who share their experience here!
You have to check Galvin these with Galvin's response
Which Vlan Lab? You mean to say LACP-STP.
pass today 06-11-2017
40 questions all from the dump, with 2 labs the radius lab and the vlans lab
today I pass the exam using the dump 191 all the question from it
my score 973
simulation STP&vtp ,Lacp,hsrp
regards
yazan
Regards.
Please update the dump .
Thank you in advance
Gump still Valid.
Guud look all.
[email protected]
Thanks,
Where can we get the 191q you are talking about.
Please make it available for everyone
Thanks
Q 48 - Which statement about SDM templates is a cisco switch is true?
Correct answer: SDM templates are used to configure system resources in a switch to optimize support for specific features depending on how the switch is used in the network.
Incorrect Answer: SDM templates are configured by accessing the switch using web interface. (LOOOOL)
here is an example on how you configure an SDM template:
Switch(config)# sdm prefer dual-ipv4-and-ipv6 default
Switch(config)# exit
Switch# reload
Proceed with reload? [confirm]
LOOOOL!!!
if i purchase only the ETE and download here the free exam, are all the questions will be accessible or i must pruache the ETE and the dump package?
would you please send me the valid dumps on [email protected],
Thanks
Can some one show us the nitty gritty of the below question? it's now sure yest whether 2000 or 8000 is the correct answer!!
QUESTION NO: 182
Which option is the minimum number of bindings that the DHCP snooping database can store?
A. 1000 bindings
B. 2000 bindings
C. 5000 bindings
D. 8000 bindings
Answer: D
I found something interesting here:
http://www.prepaway.com/certification-training/ccnp-configure-and-verify-switch-security-features.html
Restrictions:
The following restrictions should be noted down while configuring the DHCP snooping:
At least 8000 bindings can be stored on DHCP snooping database with Releases after 12.2(18)SXF5.
Best luck
Ahmed
Can anyone of send me valid dumps for 300-115 PDF version to [email protected]?
With many thanks ,
Johns
inrast ser 100%
infrast secur 100%
layer 2 73%
Please help me to clear the switch exam by sharing latest dumps. Your help will be highly appreciated. Please share me on [email protected].
Thanks in anticipation.
Please send me the latest dump @ [email protected]
[email protected]
So this file is valid nothing else is needed ?
Where can I find the labs or are part of the file?
Thank you in advance
Keep calm, JvD.164q.ete is valid and it is enough to pass.
Study labs from certprep website are very good.
Can someone send me the latest PDF file. I need to sit for this very soon. Thanks in advance. star4_cool@hotmail. com
can you send me the valid dump?
[email protected]
very thank you !! Good luck
Please send me the latest dump @ [email protected]
Could someone please send me a copy of the PDF file?. I cannot open in ETE Sim. [email protected]
Thanks!!
Please send me your files. tnx
My Email : [email protected]
Galvin.158 and JvD.164 are extremely valid. But for labs, I suggest certprepare.com and that you study and pratice before take the exam.
Good luck!
I want CCNP SWITCH dump.
send to me.
[email protected]
thank you
pdf format send me please
[email protected]
Good luck
Would you send me valid dump, it would be great.
[email protected]
Thanks
Be careful in the labs values can be different, for example, the radius server 172.120.40.46, instead of 172.120.39.46, respectively I used
radius-server host 172.120.40.46 key rad123. Lab LACP-STP completely solved as described in certprepare.com Ping 192.168.1.1 was successful,
do not forget look "sh int br" To make sure that the interface Po1 is Up.
Please send me the dump at
[email protected]
300-115-CCNP Switch
Email: [email protected]
Can someone send me the latest PDF file. I need to sit for this very soon. Thanks in advance. [email protected]
Lab AAA and LACP Problem.
please send2 me correct answer and step for Lab Ferris AAA and LaACP.
email to [email protected], i appreciate about it.
could you please email me latest dumps, thanks a lot.
[email protected]
[email protected]
Big appreciate for support
please, someone send me the latest PDF file of 164q at [email protected] best regards,
Can I check if you have the latest ete player to open up the latest dump?
could you please email me latest dumps, thanks a lot.
[email protected]
Is that true??
[email protected]
Please send me dumps
[email protected]
would you please send me the updated P4S to me
mail: [email protected]
Bres CK
Please can you send valid dump and ete to me too.
My e-mail [email protected]
Thanks
Thanks in advanced!
Please email the dump to me at [email protected]. Thank you.
Congrats Bro, can you please share details @[email protected]
Q 45- Which command does a net eng uses to verify stp status for vlan 10?
Correct answer: show spanniing-tree vlan 10
Incorrect answer: show spanniing-tree vlan 10 brief
note: the question does not state how can you check the brief information for vlan 10 thus the "brief" command is not correct!
Q 44 - Which STP feature enables the rapid transition for access ports?
Correct answer: Spanning-tree portfast
Incorrect answer: Spanning-tree fastport
ps: stupid answer....
Q 42 - Net Eng just deployed a non cisco device and wants to get information about it from connected devices. Which protocol does need to be configured for different vendors to interoperate?
Correct Answer: LLDP
Incorrect Answer: NDP
Note: NDP is used for IPv6 and the question does not state any IPv6 in the network thus LLDP must be configured replacing CDP so that all devices can inter-operate.
Q 46 Correct answer: VTP summary advertizements are sent out all ports with the new domain name.
incorrect answer: Switches with higher revision number does not accept the new domain.
note: switches with higher revision number do not accept any vtp update, but the question doesnt even mention it, if all switches have null domain name (not configured) they will accept the new domain name with the first vtp advertisement sent by the switch which was configured with the vtp domain name.
im sure more answers are incorrect, these are basic stuff! Will post more when i find them
[email protected]
would you please confirm is this Q164 dump the last one & is it valid or not and if there is any change please send me the updated @ [email protected]
many thanks
i Send the dump to people who put email here
@kbsnwl
you can post the email here
best wishes
Passed today score of 853/1000.
Labs: AAAd1x, LACP, HSRP and VTP3v3.
It was little bit confusing. plz read these labs carefully.
Good Luck Every Body.
Thanks Prepaway
Please send me the dump: [email protected]
Thanks in advance.
would you please send me the valid dumps on [email protected] It would be great help.
[email protected]
[email protected]
[email protected]
Email : [email protected]
next week my exam please help
[email protected]
Br,
Kbsnwl
one of the comments on LACP lab was to apply encapsulation dot1q on the interface ranges... do not do that.. just apply them on the Port-Channel and it will get propagated to the interfaces.
Other then that.. it shud be said.. if you are failing.. you are not understanding the concept.. not memorizing the dumps.. not looking at lab failures and troubleshooting them.. throw in as many show commands u can to get the answer..
AAA dot1x, HSRP hotspot, LACP with STP sim, VTPv3
layer 2 85%
infrastructure security 100%
infrastructure services 100%
Dumps (JVD and Galvin) still valid!
Got LACP and Dot1x labs. HSRP hotspot & Ferries simlets
Labs all same in certprepare!
Just a reminder on LACP lab. I forgot to type Range in
the interface range command..hehehe. maybe thats the reason why I
did not ACE the exam!
Thanks a lot Certprepare, JVD and Galvin Dumps!
Labs: AAAd1x, LACP, HSRP and VTP3v3.
Fail in the LACP lab, I think you should be the first port-channel, and then configure the trunk link. The emulator is very rare you can´t delete the trunk link , I wish you luck
Please share the vaild with dump if possible
[email protected]
Could someone mail me the valid questions? [email protected]
jvd is valid, take care in LACP STP as on switch A & B default gateway is added and fa 0/1 of switch A is in trunk mode with switch port access vlan 98,,,do not change anything on switch A port fa 0/1.
make sure to ping router from switch B.
Study well all labs and understand them.
Can't running some command as "copy run start"
And LACP lab, there is vlan 99 in Swtch A, for what? And if we wrong input command, we can't remove the commmad.
Please help me for know true answer in Lab questions, send me to [email protected]
Labs: AAA, LACP, VTP.
If you have an android phone, you can open the dump with A+ETE software. Can also be used on PC with blue stack installed.
[email protected]
Can you send me the valid dump?
[email protected]
very Thank you
Please send me the dump: [email protected]
Congratulate Me, Please! I finally passed my 300-115 exam this morning!
I got all 36 questions, and LABs: LACP with STP, AAAdot1x, Ferries HSRP, VTPv3.
I really appreciate your kindly BIG help!
God bless you, my cool friend, @Bres CK!!!
Many thanks in Advance
Radius host is 172.120.40.46.
hi, please send me valid dump for Switch 300-115
[email protected]
Much appreciate, Ivana
Actually, i dont know how to verify aaadot1x. I just did same as cerprepare. And try to verify ASW and DSW by show running config. One more thing, you need to shutdown Fa0/1 then no shutdown again to make sure it always up.
can you send me the valid dump?
[email protected]
thanks a lot
Please send me the latest dump and if you have PDF version @ [email protected]
Thanks
if you need any help send to me @ [email protected]
LABS : LACP with STP,AAA Dot1X,Ferris Plastics. ^____^
NOTE! LABS: LACP+STP and AAA+DOT1X - It does not work to save configuration (no write memory & copy running-config startup-config). It is not required to pass.
can you please email me latest dumps
[email protected]
many thanks
[email protected]
My email address is [email protected]
Please send me dumps
I have my exam next week.
Can you send me the valid dump?
My email is [email protected]
Thanks a lot
Can you send me the valid dump?
[email protected]
Thank you very much
My email address is [email protected]
Please send me dumps
Congratulation bro, would you please send me the valid dumps on [email protected] ?? my exam end of this week. It would be great help.
BR,
I want to ETE player dump.
plz, send to me ASAP.
thank you
can you please email me latest dumps
[email protected]
many thanks
Thank you
Can you send to me? Please?
[email protected]
I have planned to take up switch certification next week. I have one imp doubt on LACP-STP simulation. I read from the fellow contributors that in the Port which connects to Router from Switch A –> Fa0/1 , we need to remove the “switchport mode access commands” and need to change it to ” switchport mode trunk ” command;
Please let me know if we also need to add “switchport trunk native vlan 99” command in Fa0/1 port that connects to the Router.
From above certprepare Intial Configs :
SWA :
————
interface FastEthernet0/1 ——> Port connecting to Router
switchport access vlan 98
switchport mode access
Configs after changing to Trunk port :
———————————————
interface FastEthernet0/1
no switchport access vlan 98
no switchport mode access
switchport mode trunk
OR, THIS…..
interface FastEthernet0/1
no switchport access vlan 98
no switchport mode access
switchport mode trunk
switchport trunk native vlan 99 ———> PLS CONFIRM IF WE ALSO NEED TO ADD NATIVE VLAN 99 COMMAND IN ADDITION TO CHANGING THIS PORT TO “TRUNK” MODE
To all the guys who have passed the exam , pls confirm what needs to be done here …
Eagerly Awaiting your valuable inputs friends ….
I have my exam next week.
Can you send me the valid dump?
my email is [email protected]
Thanks a lot
My email address is lili.vachon @ gmail
Please send me dumps
36 quastion
lab aaadot1x , lacp , Vtp v3 , hsrp
anyone need to dump you can post the email here
Found valid 300-115 dumps from Google, if you need them, please leave your E-mail here.
pls send me the dumps for switching
email
[email protected]
can you share 300-155 dumps with me please
and I need ETE player Please
email : [email protected]
Thank you
which answer is correct B or C?
all question from this Dump
all simulation from like 9tut
HSRP , LACP wiht stp , AAA dot1x , FERRIS
Congratulation for passing with cent percent. Could you please be helpful to share me the dumps to [email protected] ?
Congratulation bro, would you please send me the valid dumps on [email protected] ?? my exam end of this week. It would be great help.
BR,
lab is aaadot1x , lacp , vtp v3 , hsrp
Which Radius Host IP Address did you used?
172.120.39.46 or 172.120.40.46?
Please send me a copy to [email protected]
Who knows where I can download ete player, I want to open this file.
Labs:
Ferris, VTP3, LACP+STP, AAA
All the questions from JvD dump.
[email protected]
Thank you very much
Good luck.
can any body send tell me about Lacp lab i had problem on the exam
I did the exam yesterday 1pm in frankfurt and passed with 853.
I would 100% surely every questions from JVD 164 and Galvin 158. In gakvin all the questions and answers are correct and in JVD 43 to 53( nearly 10 questions) wrong, but cross check with the galvin as galvin is 100 corrct.
Additionally there are some extra questions in JVD (158 to 164 = 6Questions) anf those are very very important as i got almost every thing from there. please find 5 of them below (1 question was same as in galvin)
*** QUESTION 1 ***
RSPAN has been configured on a Cisco catalyst switch ; however, traffic is not being replicated to remote switch . which type of misconfiguration is a cause ?
A. The Local Switch is overloaded with the amount of sourced traffic that must be replicated
to the remote switch
B. The RSPAN designated VLAN is missing the remote span command
C. The Local & Remote RSPAN switches are configured using different session IDs
D. The Local RSPAN switch is replicating only Rx traffic to the remote switch
Answer: B
—————————————————————————————————–
*** QUESTION 2 ***
A network engineer is installing a switch for temporary workers to connect to.
The engineer dose not want this switch participating in Spanning Tree with the rest of the network, however, end user connectivity is still required. Which spanning-tree feature accomplishes this?
A. BPDUignore
B. BPDUGuard
C. BPDUblock
D. BPDUdisable
E. BPDUfilter
Answer: E
———————————————————————————————————-
*** QUESTION 3 ***
Which four LACP components are used to determine which hot-standby links become active after an interface failure within an EtherChannel bundle? (Choose Four)
A. LACP System Priority
B. Hot-standby link identification number
C. System ID
D. Interface Bandwodth
E. LACP port Priority
F. Port Number
G. Interface MAC address
Answer :A,C,E,F
——————————————————————————————————
*** QUESTION 4 ***
Sh run:
monitor session 1 source interface fastEthernet0/4 rx
monitor session 1 filter vlan 3
monitor session 1 destination interface fastEthernet0/5
What is the result of the SPAN configuration on a Cisco switch?
A. Configure SPAN session to monitor the received traffic on interface f0/4 only for VLAN 3
B. Configure SPAN session to monitor the received traffic on interface f0/5 only for VLAN 3
C. Configure SPAN session to monitor the received traffic on interface f0/5 for all VLANs
except VLAN 3
D. Configure SPAN session to monitor the received traffic on interface f0/4 for all VLANs
except VLAN 3
Answers: A
—————————————————————————————————-
*** QUESTION 5 ***
Switch (config)# spanning-tree portfast default
% Warning: this command enable portfast by default on all intrfaces.you
should now disable portfast explicitly on switched ports leading to hubs,
switches and bridges as they may create temporary bridging loops.
Switch(config)#
When troubleshooting a network problem, a network analyzer is connected to port f0/1 of a LAN switch Which command can prevent BPDU transmission on this port?
A- spanning-tree portfast bpdufilter default
B- spanning-tree portfast bpduguard enable
C- no spanning-tree link-type shared
D- spanning-tree bpduguard default
Answer: A
For those who wants the ETE playrer, plase find the android app for the ete player. https://play.google.com/store/apps/details?id=com.on_labs.android.aplus&hl=de
you will not get all 158 questions with the time. but you can go to each and every questions and do them and see the correct answer. And I hope this is far easier as you can do it while travelling ;)
About the Labs.
Everything was from Certpreapre.
HSRP, VTPv3, LACP with STP, MLS and eigrp and AAdot1x lab.
Everything was as the certpreapare.
About the VTPv3 lab Q#3- i got the switches as version 3 but the operation mode was SERVER in SW1 ans SW2, So it is same as galvin answer not as certprepare.
If you need anythings to ask, please ask me, [email protected]
Good luck. Study well.
except,
1- LACP you have to ignore the one in dump and study from certprepare.com
2- AAA lap you have to change server radius host ip 172.120.40.46 instead of 172.120.39.46 as dump.
good luck
please tell me i have to gave exam after mid of august.
thanks
My email address is [email protected]
Please send me dumps
Thank you.
- LACP with STP , Ferris, VTVv3, HSRP same with certprepare.com
- AAAdot1x: change IP:
+ server host : 172.120.40.46
+ vlan 20 : 172.120.40.0/24
All the best.
AAA and lack with stp practical, and and smal fari factory question
Was there, I jest give answer but not troubl shot, total was 36 question
So give me the tip for next exam, AAA and lacp can save and
Smol factory question like core and distribution lyre switches and
Access will troubl shoot or simple give question answer
It is still valid, Thanks god I PASSED
Dont Worry You can't save the config in the labs, But the exam takes your answers.
You could help on the labs with autocomplete commands clicking on the tab key.
LABS LACP with STP,AAA,VTPv3, Ferris Plastics.
The second one JVD.164q has the new questions are very important!!!
If you use dumps with the answer inside you will pass!! May be you dont get the score 1000/1000 but you will pass!! It may be some answer are wrong, I dont change any answer and I passed.
I think your final score will depend a lot of LACP with STP, you must complete this LAB very good.
If you do this you will pass!!!
I advice you understand the questions and the answer.
Can anyone confirm if the answers in dump are also correct too?
Also does it contain simulations? Any drag and drop in this exam?
Thanks guys and BEST OF LUCK with your goals.
Passed today with this JVD.ete...
All questions and labs came from here.
LABS LACP,AAA,VTPv3, Ferris Plastics...
Thanks to JvD for dumps and certprepare
Good Luck
in this weekend. Coz I going to take the 300-115.
Okay,, after test I will tell you guys.
Today I passed Switch 300-115 core , I’m just stay at home after distance over 250 km to VUE from here. I always take note that I still recommend me to understand thoroughly material and I done very well with 1000 score !!!!!!
Thank you so much all everything .
It’s time to continue for Tshoot exam , the end of CCNP .
Lab : AAAdot1x , LACP with STP , Ferris, VTVv3, HSRP
material’s same same JvD 164 .
Good luck guys !
Simulations are HSRP, Ferris, AAA and LACP with STP. Study certprepare for the labs.
However, the labs (AAA and LACP) have bugs, you can't save the configuration because copy run start is not recognized. Tried even the complete command syntax and all the commands I know to save my configuration such as write memory but no luck at all. It wasted most of my time so decided to move forward.
My tip is perfect the multiple questions as you can so you have a better chance to pass.
Cheers!
1. A network engineer is installing a switch for temporary workers to connect to. The engineer does not want this eitch to participate in spanning tree however end user connectivity is still required.
A. BPDUignore
B. BPDUGuard
C. BPDUblock
D. BPDUdisable
E. BPDUfilter
I would say E. BPDUfilter, as BPDUguard will shut down the port if it sees a BPDU. Is this right?
Also this question is giving me headache:
2. When troubleshooting a network problem, a network analyzer is connected to port f0/1 of a LAN switch. Which command can prevent BPDU tansmission on this port?
A. Spanning-tree portfast bpdufilter default
B. Spanning-tree portfast bpduguard enable default
C. no spanning-tree link-type shared
D. spanning-tree bpduguard default
I think this is 'A. Spanning-tree portfast bpdufilter default'. I think this because BPDUfilter is the only that that stops port from actually sending BPDUs. BPDUguard still sends BPDU but shuts down port if it hears any back, and I don't know what the other command does.
Does this sound right?
Any help will be very welcome on these two questions.
I passed yesterday with 958/1000.
I hope to help with this entry:
36 multiple-choice questions
LAB: LACP STP + / AAA + dot1x / VTP3 / HSRP (only check)
Dump still valid.
BE CAREFUL IN LABS:
LACP + STP
I started by SWA.
First, I applied a command "show cdp neighbors" and I saw the router's IP (192.168.1.1).
NOTE: You dont need to change the F0 / 1 interface to trunk
VLANs 11, 12 and 13 were already created.
1 - I set the spanning-tree as "primary root" for VLANs 11-13,21-23 (the simulator accepts range separated by a hyphen / comma).
2 - So I created VLANs 21, 22 and 23 with their respective names.
3 - I configured the interfaces f0 / 3-4 (ATTENTION: need to have space).
Removed the access switch settings and VLAN 98 (the switchport mode access / no switchport access vlan 98).
Created the channel (channel-group 1 mode active / channel-protocol lacp).
Activated the interface (no shutdown).
4 - I entered the interface Portchannel 1
5 - Configured trunk:
switchport mode trunk
6 - I configured the Native VLAN:
switchport trunk native vlan 99
switchport trunk allowed vlan 1,21-23
7 - Activated the interface (no shutdown)
ATTENTION: I even put the "switchport mode trunk" and appearing in "show-run" I had to apply the interfaces f0 / 3 - 4. Because when I applied "show interfaces f0 / 3 switchport" displayed as ACCESS MODE. Then I applied only "switchport mode trunk" in the interface f0/3 - 4
SWB:
1 - I created the VLANS 21,22 e 23 with their respective names.
2 - I created the Native Vlan 99
3 - I configured the interface range f0/9 - 10 (mode access/vlan 21/portfast/no shutdown)
I configured the interface range f0/13 - 14 (mode access/vlan 22/portfast/no shutdown)
I configured the interface range f0/15 - 16 (mode access/vlan 23/portfast/no shutdown)
4 - I configured VTP mode transparent (vtp mode transparent)
5 - I configured STP (spanning-tree mode rapid-pvst)
ATTENTION: I do not set a default route on SWB, because the LAB says SWB shouldn't have route.
6 - The VLAN 1 had a configured IP, but I applied the command SHUTDOWN / NO SHUTDOWN.
7 - I configure the interface f0-3 - 4 (PASSIVE to channel)
channel-group 1 mode passive
channel-protocol lacp
no shutdown
8 - I configured the interface Portchannel 1 (ATTENTION: You need apply the command "switchport trunk encapsulation dot1q" before the command "switchport mode trunk".
9 - I set up the Native VLAN:
switchport trunk native vlan 99
10 - Allow Vlan 1, 21-23 (switchport trunk allowed vlan 1,21-23)
11 - Activated the interface (no shutdown)
At this time I preferred to apply the command "shutdown / no shutdown" at the interfaces f0/3 - 4 and PortChannel 1 as a precaution.
I checked all configuration:
show etherchannel summary
show interfaces trunk
show run
show vtp status
show spanning-tree summary
show interfaces f0/3 or f0/4
show interfaces f0/3 or f0/4 switchport
I could do a ping to Router normally.
========================
AAA + DOT1X
SW ASW1: The f0 / 1 interface was already configured as ACCESS and VLAN 20.
1 - I set the AAA (aaa new-model)
2 - I set Radius Server (172.120.40.46) key rad123
3 - I set Radius to used for 802.1x authentication "aaa authentication dot1x default group radius"
4 - I set DOT1X globally "dot1x system-auth-control"
3 - I set the interface f0/1 to force PC autheticate through the 802.1x "dot1x port-control auto" NOTE: The IOS does not recognize the "dot1x pae authenticator" command.
show dot1x interface f0/1
show dot1x all
SW DSW1:
1 - I created the ACL Standard 10 (permit 172.120.40.0/24)
2 - I created the vlan access-map PASS 10 (match ip add 10 / action forward)
3 - I created the vlan access-map PASS 20 (action DROP)
NOTE: Before applying the command "vlan filter PASS vlan-list 20". Make sure the VACLs are correct.
show access-list 10
show vlan access-map PASS
show run
If everything is correct, apply the filter.
Check again
Still valid.
All the ques were same frm JVD-164
labs were aaa dot1x,ferries,lacp and vtp3
In aaadot1x:-
switchport mode access
swichpor access vlan 20 were already configured,
just put
dot1x port-control auto
no shut
and in lacp here were few bugs bt overall it was ok
HOPE tht helped guyss,nw heading for Tshoot cheers!!!!!!
-----------------
dot1x system-auth-control
aaa new-model
radius-server host 172.120.39.46 key rad123
aaa authentication dot1x default group radius
interface fastethernet 0/1
switchport mode access
***User Connecting port should be accecc mode***
dot1x pae authenticator
***pae: port access entity, this is for user connecting port with the dot1x enabled switch,
tell switch port act as authenticator for this port***
dot1x port-control auto
***if a user authenticate successfully, then user allows to forward traffic through that switch port***
ip access-list standard 10
permit 172.16.30.0 0.0.0.255
exit
vlan access-map rpn 10
match ip address 10
action forward
exit
vlan access-map rpn 20
action drop
exit
vlan filter rpn vlan-list 20
copy running-config sratup config
Verify cmds:
show dot1x all summary (show authentication enabled port)
show vlan access-map
NOTE: These commands got from Nugget videos, and i don't is this configuration correct or wrong... plz submit your comments.....
what is the reason ?