Log into your Prepaway Account
Please Log In to download ETE file or view Training Course
Registration is free and easy - just provide your E-mail address.
Click Here to Register
Exam: | 200-125 - Cisco Certified Network Associate |
Size: | 8.1 MB |
Posted: | Tuesday, September 5, 2017 |
Download:
|
Cisco.Pass4sure.200-125.v2017-09-05.by.kimberly.314q.ete |
Download Free 200-125 Exam Questions |
Log in to make your opinion count.
Registration is free and easy - just provide your E-mail address.
Click Here to Register
Use Discount Code:
A confirmation link was sent to your e-mail.
Please check your mailbox for a message from [email protected] and follow the directions.
Yes, Their is a multiple choice EIGRP question. But make sure you answer them carefully.
Their are two way's they could ask the questions. (Read all the comments to get an idea or check the CCNA dump as well).
And their is a EIGRP simulation like ACL2. a similar one to this simulation should be available in the watson dump.
So make sure you are confident before you go for the exam.
Good Luck!!
I can't find the OSPF sim in the dump, wher did you get it ?
Can you please confirm whether these dumps are valid in the UK?
Thanks
Q1:R4 has been incorrectly configured to be in another AS, so it does not peer with R5.
Q2:The traffic goes through R2.
Q3:network command is missing.
Q4:The network statement is missing on R1.
OSPF (Same)
Q1. There is an area ID mismatch.
Q2. There is an OSPF hello and dead interval mismatch.
Q3. R1 ethernet0/1 configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
Q4. The R3 router ID is configured on R6.
ACL1 (Same)
ACL2 Mod 3 – Host IP’s changed to 192.168.34.1 – 4 and there are 2 servers only. Finance Server IP changed to (172.22.55.17)
EIGRP Troubleshooting Sim Answer :
Q1: The loopback addresses haven’t been advertised, and the network command is missing on R4.
Q2: The traffic is equally load-balanced over R2 and R3.
Q3: The K values mismatch.
Q4: The network statement is missing on R5
-ACL1 - same
-ACL2 — mod4
-OSPF — same
-EİGRP troubleshooting —answer change
Answers:
A. It enables the transmission of IPv6 packets within the configured tunnel.
B. It specifies IPv4 as the encapsulation protocol.
dumps is valid 100%.
also you can watch my youtube channel ITkings,
ccna exam lab access list sim 1 or sim 2.
thanks.
Dumps watson is valid 100%.
40 questions
Simulation questions
OSPF (Same)
Q1: There is an area ID mismatch
Q2: There is an OSPF hello and dead interval mismatch
Q3: R1 Fa0/1 configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
Q4: The R3 router ID is configured on R6.
ACL Sim 1 (Same)
Q1: Remove access-group 106 in from interface fa0/0 and add access-group 104 in
Q2: All traffic from the 10.4.4.0 network would be allow to go through
Q3: Hosts cannot connect to Router through s0/0/1
ACL Sim 2
(Modified Host A Modification 4 ip changed for Finance server = 172.22.213.17
EIGRP Troubleshooting Answer:
Q1=the loopback addresses haven't been advertised, and the network command is missing on R4.
Q2=Th traffic is equally load-balanced over R2 and R3.
Q3=the K values mismatch.
Q4=The network statement is missing on R5.
Some answers in this file are not 100% right, attention please!!!
BTW, the 200-125 exam will be retired on December 4, 2017, then the 200-125 exam will be fully replaced by the new 200-125 exam!
some telling that it has 2 sets of qstns and different answers for both.
Am completely studying 364/314 dump.
Guys who wrote on first week of august, confirm and tell me with eigrp answers please....
am taking exam next week.
Watson 98% still valid dumps, Check simulations/lab
* ACL2 —mod3
* ACL1 — same
* OSPF — same
* EİGRP troubleshooting —answer change
Q1= The loopback addresses haven’t been advertised, and the network command is missing on R4.
Q2= The traffic is equally load-balanced over R2 and R3.
Q3= The K values mismatch.
Q4= The network statement is missing on R5
You used 314 or 364 version?
I passed the test that score got 961.
This dump was whole valid but excepted two questions.
New 2 questions : L2 Etherchannel and SNMPv2 Authentication
Am confused with eigrp sim answers, there 2 sets of answer.
old:
EIGRP:
Q1:R4 has been incorrectly configured to be in another AS, so it does not peer with R5.
Q2:The traffic goes through R2.
Q3:network command is missing.
Q4:The network statement is missing on R1.
New:
EIGRP Troubleshooting Answer:
Q1=the loopback addresses haven't been advertised, and the network command is missing on R4.
Q2=Th traffic is equally load-balanced over R2 and R3.
Q3=the K values mismatch.
Q4=The network statement is missing on R5.
AND recently a new update that 2 old answers and 2 new answers eigrip sim i.e
Q1.old answer
Q2.new answer
Q3.new answer
Q4.old answer
Those who took exam 3-4 days ago and passed with 940 or 914 kinda marks would have lost in this eigrp sim answers and can any confirm with the answers who took exam recently and scored more???
Help needed
There are two new questions and some changes in the troubleshooting laps...
Goodluck everybody..
and about the new EIGRP i think i have it in the dump is it the same sim ?
is dump still valid in India ?
I want take exam in this week
All hosts in the Core and local LAN should be able to access the Public Web Server
* access-list 100 permit ip any any
used. What is the maximum number of usable IP addresses that can be supported on each LAN if the organization is using one class C address block?
A. 8
B. 6
C. 30
D. 32
E. 14
F. 16
I so confused about the answer of this question. If someone can make sure about the aswer please tell me. I confused between 14 and 30. Thank for any help
One of them was:
What setting does not require to be the same on different ports on an etherchannel?"
* speed
* DTP negotiation setting (right answer!)
* duplex
* trunking encapsulation
Labs were: ACL1, ACL2 (Mod 3), OSPF & EIGRP.
All the best..!!!
Got a score of 1000/1000 for the 1st take! I reviewed for almost 2months
Scope of exam: Watsons314q, EIGRP troubleshooting (k value mismatch. use show run, show ip route, show ip protocol commands), OSPF troubleshooting (same problem here in 9tut. use show run command), ACL 1 (same problem here in 9tut), ACL 2 (mod 4)
My advice to all future examinees:
Memorize and understand the watsons314q. It helped a lot. No Tab key and ? in the exam(not all shortcut commands are available). Try to memorize the commands or atleast memorize the shortcut command like show run, ena, show ip route.
SNMPv2 authentication protocol >> Community string
dumps is valid u can stdy it.
OSPF -same
EIGRP -same (one answer different is K value mismatch)
ACL 2 -Modification 3 some time changed.
ACL 1 -same
u can practice acl2 many time as u can.
watch my youtube channel ITkings i make video lab acl-1 and acl-2.
have any problem u can comments.
Good luck .
39 questions (Watson) 1 question (Konrad)
OSPF (Same)
ACL Sim 1 (Same)
ACL Sim 2 (Modified Host A allow,other block)
EIGRP Troubleshooting Answer:
Q1=the loopback addresses haven't been advertised, and the network command is missing on R4.
Q2=Th traffic is equally load-balanced over R2 and R3.
Q3=the K values mismatch.
Q4=The network statement is missing on R5.
Watson+Konrad is valid.
Labs: EIGRP, OSPF, ACL1 and ACL2.
314 Watson enough ? or we need prepare 364 questions as well ?
dumps is valid in US,u need any help about CCNA labs watch my youtube channel IT Kings and comment.thanks
good luck !!!!
Still valid in Egypt passed 961/1000 on Sunday 11/28/2017
Valid with one new question of 40 questions
Simulation questions
OSPF (Same)
Q1: There is an area ID mismatch
Q2: There is an OSPF hello and dead interval mismatch
Q3: R1 Fa0/1 configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
Q4: The R3 router ID is configured on R6.
ACL Sim 1 (Same)
Q1: Remove access-group 106 in from interface fa0/0 and add access-group 104 in
Q2: All traffic from the 10.4.4.0 network would be allow to go through
Q3: Hosts cannot connect to Router through s0/0/1
ACL Sim 2
(Modified Host B Modification 4 (Mod 4)) ip changed for Finance server = 172.22.213.17
EIGRP Troubleshooting Answer:
Q1=the loopback addresses haven't been advertised, and the network command is missing on R4.
Q2=Th traffic is equally load-balanced over R2 and R3.
Q3=the K values mismatch.
Q4=The network statement is missing on R5.
ospf eigrp same as watson
three new questions...
1) GLBP
2)frame relay
3)one from switching
labs
ospf-same
acl1-same
Eigrp-troubleshooting
acl2-mod1 with IP's value changed
be careful guys mostly with simulations try to cover all mods of acl2
This dump is valid
thanks my god... passed today 941 ..i'm from egypt
the dump still valid but pls take care the sorting of answers is different
When you said same question. Is that that your second shot ?
Passed today 980/1000
All question from watson 314q + pass4shure
ACL1 – Same
ACL2 – Same (mod 3)
OSFP Tshot – Same
EIGRP Tshot – new answer
EIGRP troubleshooting answer:
Q1: The loopback addresses haven’t been advertised, and the network command is missing on R4.
Q2: The traffic is equally load-balanced over R2 and R3.
Q3: The K values mismatch.
Q4: The network statement is missing on R5
ACL2 Answer: HOST C
1- access-list 100 permit tcp host 192.168.33.3 host 172.22.242.23 eq 80
2- access-list 100 deny ip any host 172.22.242.23
3- access-list 100 permit ip any any
39 questions (Watson) 1 question (Konrad)
OSPF (Same)
ACL Sim 1 (Same)
ACL Sim 2 (Modified Host A allow,other block)
EIGRP Troubleshooting Answer:
Q1=the loopback addresses haven't been advertised, and the network command is missing on R4.
Q2=Th traffic is equally load-balanced over R2 and R3.
Q3=the K values mismatch.
Q4=The network statement is missing on R5.
most of the questions are the "three and two answer multiple choice"..
The only configuration lab is the ACL2(Allow access to finance server )the rest ACL,OSPF,EIGRP are multiple choice.
Thanks to Watson...
and good luck to every one else...
Good Luck!
A and. B
Same 4 sim, ACL1, ACL 2 modification, OSPF, EIGRP and 40 question.
EIGRP:
Q1:R4 has been incorrectly configured to be in another AS, so it does not peer with R5.
Q2:The traffic goes through R2.
Q3:network command is missing.
Q4:The network statement is missing on R1.
Thank you
Goodluck everybody..
Jel je vazeci ovaj dump u Srbiji, jel zna neko? Hvala unapred
Thank you very much.:)
Labs:OSPF, EIGRP, ACL1+2.
Yes dump still valid 100% .. I passed CCNA
I have dump watson 364q
good lock for every one
Watson 314,and actualtest v26 447Q still valid
SIM are:
1/ OSPF – T.Shoot (Same)
2/ EIGRP – T.Shoot Answer:
Q1=the loopback addresses haven’t been advertised, and the network command is missing on R4.
Q2=Th traffic is equally load-balanced over R2 and R3.
Q3=the K values mismatch.
Q4=The network statement is missing on R5.
3/ ACL 1 (same)
4/ ACL 2 (Mod 3) host A.IP addresses changed
(1) lab question which involved 5 router and 1 switch (i think) and ask which router it take from R1 to R5.
(2) Eigrp - likt posted here
Need explanation and answer .. >
All the best for the exam
40 preguntas 1 lab 3 Tshoot 2 Drag and Drop
Simulation questions
OSPF (Same)
Q1: There is an area ID mismatch
Q2: There is an OSPF hello and dead interval mismatch
Q3: R1 Fa0/1 configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
Q4: The R3 router ID is configured on R6.
ACL Sim 1 (Same)
Q1: Remove access-group 106 in from interface fa0/0 and add access-group 104 in
Q2: All traffic from the 10.4.4.0 network would be allow to go through
Q3: Hosts cannot connect to Router through s0/0/1
ACL Sim 2
(Modified Host A Modification 3 (Mod 3)) ip changed for Finance server = 172.22.220.17.
EIGRP Troubleshooting Answer:
Q1=the loopback addresses haven't been advertised, and the network command is missing on R4.
Q2=Th traffic is equally load-balanced over R2 and R3.
Q3=the K values mismatch.
Q4=The network statement is missing on R5.
LEAN DETENIDAMENTE TODO! y estén muy relajado.
Buena suerte.
1/ Dump with 364 Question is enough, try to remember all answers
2/ Practice for SIMs (Special ACL 1, ACL 2, OSPF, EIGRP Troubleshoot)
Goodluck.
i makeing eigrb lab very soon for ur friend.
thanks alot.
you need to write a letter to support your ETE player.
https://learningnetwork.cisco.com/community/ccna-rs-certification
can anyone confirm that plzzzzzzz
Watson 314 valid
Eigrp change
Ospf change
Acl same
I have exam next week
if you are gone to retake it will be different but not at all questions. study well & good luck
only acl simulation is same..other simulations are new for eigrp,acl simlet and ospf...stay calm and study simulation correctly and there 8 new mcq asked too..
still valid watson 314q.
Thanks
Score 961/1000
still valid Watson 100%.
4lap:
- acl1 same 9tut
-acl2 mode 3 ip change
-Eigrp troubleshooting
+The loopback addresses haven‘t been advertised, and the network command is missing on R4
+ The traffic is equally load-balanced over R2 and R3.
+ The K values mismatch.
+ The network statement is missing on R5
-OSPF
+There is an area ID mismatch
+There is an OSPF hello and dead interval mismatch
+R1 Fa0/1 configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
+The R3 router ID is configured on R6
Goodluck guy!
the answers are A&B
A:it enable the transmission of ipv6 packet with in the configured tunnel
B:it specifies ipv4 as the encapsulation protocol
Number of questions: 40
Watson 364 valid 100%
ACL, OSPF and EIGRP labs same. Good luck!
As I am doing my CCNA for the first time. I am not aware that there are simulation questions as well? & are they options based? or do we have to type commands for it? Help is highhly appreciated
for the last few days i am seeing a lot of people failing the exam saying that they added few new questions to the exam . i am taking the exam next week and i am learning from watson 360 q . should i learn from other dump or dump still valid?
how are you
my friend
@Naul, how many questions do you encountered in exam?
dump it's valid or not ?
you mentioned 364q where that questions, here only 314 ?? any one confirm please
Please Help
Its still valid in Oman
good luck for all.
passed yesterday(980/1000).1-2 new questions...dump is 99% valid.
ALL THE BEST GUYS
Where did you test it? In which center? Valid 1000% ?
Thanks
OSPF neighbors - same
EIGRP:
Q1:R4 has been incorrectly configured to be in another AS, so it does not peer with R5.
Q2:The traffic goes through R2.
Q3:network command is missing.
Q4:The network statement is missing on R1.
ACL1: Same
ACL2: Host B
I would say 85% of this was on the exam. (USA)
This dump is valid
1st LAB ACL (show commnad)
2nd LAB ACL (finance server and host)
3rd LAB OSPF (6 rouuters and 2 swithes)
4th LAB EIGRP (4 branch offices 1 central office)
other question came from WATSON and KONRAD dumps.
thank you
dump is still 100% valid
thanks 9tut.com
Same 4 sim, ACL1, ACL 2 modification, OSPF, EIGRP and 40 question.
EIGRP:
Q1:R4 has been incorrectly configured to be in another AS, so it does not peer with R5.
Q2:The traffic goes through R2.
Q3:network command is missing.
Q4:The network statement is missing on R1.
Thank you
Goodluck everybody.
same OSPF
same EIGRP
Same ACL just different IP address.host c connect to fin web server
but passed today with score 902
Watson Konrad still valid dumps, Check simulations/lab
* ACL2 —mod3
* ACL1 — same
* OSPF — same
* EİGRP troubleshooting —answer change
Q1= The loopback addresses haven’t been advertised, and the network command is missing on R4.
Q2= The traffic is equally load-balanced over R2 and R3.
Q3= The K values mismatch.
Q4= The network statement is missing on R5
Goodluck!
I got labs the same.EIGRP,OSPF,ACL1(multiple choice) ACL2 Modification 3 I used Use access-list 100 permit ip any any
EIGRP troubleshoot :
Configuration on router had been changed ,AS Shown
Q1. The loopback interfaces on R4 with the IP addresses of 10.4.4.4/32, 10.4.4.5/32 and 10.4.4.6/32 are
Ans:
R4 and R5 is same AS number but R4 don’t advertised all loopback (10.4.4.4/32, 10.4.4.5/32 and 10.4.4.6/32).
Answer is
The loopback addresses haven’t been advertised, and the network command is missing on R4.
_______________________
Q2. Which path does traffic take from R1 to R5?
Ans: The answer was that the packets will go R1->R2->R5 AND R1->R3->R5
with equal-cost balancing (sh ip route and you’ll see two possible routes to R5 with equal eigrp metric)
________________________
Q3. Router R6 does not form an EIGRP neighbor relationship correctly with router R1. What is the cause for this misconfiguration?
sh run in Router 6
router eigrp 1
network 10.6.6.6 0.0.0.0
network 192.168.16.0
metric weights 0 0 0 1 1 1
auto-summary
so the correct answer is The K values mismatch.
____________________________
Q4. Study the following output taken on R1:
R1#ping 10.5.5.55 source 10.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.5.5.55, timeout is 2 seconds:
Packet sent with a source address of 10.1.1.1
Why are the pings failing?
A. The network statement is missing on R5.
B. The loopback interface is shut down on R5.
C. The network statement is missing on R1.
D. The IP address that is configured on the Lo1 interface on R5 is incorrect.
A is the correct answer …
Labs:
ACL2 —Modification 3
ACL1 — same
OSPF — same
EİGRP troubleshooting answer:
Q1= The loopback addresses haven’t been advertised, and the network command is missing on R4.
Q2= The traffic is equally load-balanced over R2 and R3.
Q3= The K values mismatch.
Q4= The network statement is missing on R5
ACL1 same
ACL2 same,host D
EIGRP differnet
Dumps watson is valid 100%.
40 questions
Simulation questions
OSPF (Same)
Q1: There is an area ID mismatch
Q2: There is an OSPF hello and dead interval mismatch
Q3: R1 Fa0/1 configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
Q4: The R3 router ID is configured on R6.
ACL Sim 1 (Same)
Q1: Remove access-group 106 in from interface fa0/0 and add access-group 104 in
Q2: All traffic from the 10.4.4.0 network would be allow to go through
Q3: Hosts cannot connect to Router through s0/0/1
ACL Sim 2
(Modified Host A Modification 4 ip changed for Finance server = 172.22.213.17
EIGRP Troubleshooting Answer:
Q1=the loopback addresses haven't been advertised, and the network command is missing on R4.
Q2=Th traffic is equally load-balanced over R2 and R3.
Q3=the K values mismatch.
Q4=The network statement is missing on R5.
QUESTION ETHERCHANNEL: ANSW "PASSIVE"
@FAOZI answ "A" and "B"
good luck!
Watson 314 is vald 100%
But better stady in watson 364
My be you will see one or two question
i am waiting for new solution
i have the dump with 364 questions , i want to know if it is still valiad
Labs:
ACL2 —Modification 3
ACL1 — same
OSPF — same
EİGRP troubleshooting answer:
Q1= The loopback addresses haven’t been advertised, and the network command is missing on R4.
Q2= The traffic is equally load-balanced over R2 and R3.
Q3= The K values mismatch.
Q4= The network statement is missing on R5
THANKS TO UMAR ,linkent AND MIDHUN
not in dump. Make sure you study n understand the Watsons314q...
ACL-2(Only Host D should be able to access Fin-Ser, ip's changed for Fin-server)
ACL Sim 1 (Same)
Q1: Remove access-group 106 in from interface fa0/0 and add access-group 104 in
Q2: All traffic from the 10.4.4.0 network would be allow to go through
Q3: Hosts cannot connect to Router through s0/0/1
EIGRP
Troubleshooting Answer:
Q1=the loopback addresses haven't been advertised, and the network command is missing on R4.
Q2=Th traffic is equally load-balanced over R2 and R3.
Q3=the K values mismatch.
Q4=The network statement is missing on R5.
IMPORTANT NOTE :- Their are another set of answers for this same EIGRP simulation.So make sure you prepare for both.
OSPF T-Shoot (Same)
Q1: There is an area ID mismatch
Q2: There is an OSPF hello and dead interval mismatch
Q3: R1 Fa0/1 configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
Q4: The R3 router ID is configured on R6.
Good Luck guy's....
Lab (1) how to check the ospf route is not show on other router.* it have 5-6 router and 1-2 switch
Lab (2) eigrp
need someone help to give all the 4 lab explanation and answer, please help ! >
Acl1
Acl2
Ospf
Eigrp troubleshooting
ospf
eigrp (change in options, just like pre-commenter said)
ACL 1 and ACL 2.
Goodluck to everyone
the answer in the exam is like arrangement watson or different arrangement
Which two statements about the tunnel mode ipv6ip command are true? (Choose two.)
A. It enables the transmission of IPv6 packets within the configured tunnel.
B. It specifies IPv4 as the encapsulation protocol.
C. It specifies IPv6 as the encapsulation protocol.
D. It specifies IPv6 as the transport protocol.
E. It specifies that the tunnel is a Teredo tunnel.
Answer: A,B
Cheers
Do we need to only choose correct answer or need to configure with command line in TShoot and ACL 1 SIM ?
thanks so much
Q1:R4 has been incorrectly configured to be in another AS, so it does not peer with R5.
Q2:The traffic goes through R2.
Q3:network command is missing.
Q4:The network statement is missing on R1.
OSPF Same
ACL1 Same
ACL2 Mod 3
EIGRP Troubleshooting Sim Answer :
Q1: The loopback addresses haven’t been advertised, and the network command is missing on R4.
Q2: The traffic is equally load-balanced over R2 and R3.
Q3: The K values mismatch.
Q4: The network statement is missing on R5
Q-40
watson 364 valid 100%
Thanks watson , prepaway and 9tut
EIGRP Tshoot answer changes details already there in below comments
acl1,
acl2,
ospf,
eigrp
, configurations and host a changed in acl
one Question not there it's related to SNMPv2 security:
options: SMAC MD5 - SMAC SHA - and two other options lol
Could you kindly understand that this is not a place to beg and to just testify if the dump is valid or not so that other can get help from it.
Why no one wants to try it and put out the genuine views about the dump which would help everyone instead of being mean and spamming the space by being lazy and begging for pdfs
I forgot to put the access group on the interface sim 2
like: beteween R1&R2 ospf dead interval
or
network missing in router ospf
or
mismatch of area
40 questions
Simulation questions
OSPF (Same)
Q1: There is an area ID mismatch
Q2: There is an OSPF hello and dead interval mismatch
Q3: R1 Fa0/1 configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
Q4: The R3 router ID is configured on R6.
ACL Sim 1 (Same)
Q1: Remove access-group 106 in from interface fa0/0 and add access-group 104 in
Q2: All traffic from the 10.4.4.0 network would be allow to go through
Q3: Hosts cannot connect to Router through s0/0/1
ACL Sim 2
(Modified Host C Modification ip changed for Finance server = 172.22.213.17
EIGRP Troubleshooting Answer:
Q1=the loopback addresses haven't been advertised, and the network command is missing on R4.
Q2=Th traffic is equally load-balanced over R2 and R3.
Q3=the K values mismatch.
Q4=The network statement is missing on R5.
This dump is still valid, but there was one new question..
Good luck to all !
Passed today 941/1000 => file Watson 314
Lap: OSPF Nei (Same), EIGRP (New Answer), ACL1 (Same), ACL2 Mod 3
Qs: GLBP, SNMP, HSRV, VLANs, …
This dump is still valid in kuwait
Labs are OSPF, EIGRP, ACL 1, ACL 2.
any question I will do my best to help my email WowFuzik at G m a I l. c o m
I WILL REPEAT ON 17 AUGUST
GOOD LUCK FOR ALL
please help me my exam on 14 jun
please i need some comments about dumps, anybody that wrote his or her exam today can share his or her experience. thanks
i am taking this exam in next week.
till then these dumps will be valid or not ?
i am really tensed as this is my very first certification exam.
i would really appreciate a reply.
thanks , God bless all.
thanks I got it
A. It enables the transmission of IPv6 packets within the configured tunnel.
B. It specifies IPv4 as the encapsulation protocol.
C. It specifies IPv6 as the encapsulation protocol.
D. It specifies IPv6 as the transport protocol.
E. It specifies that the tunnel is a Teredo tunnel.
what is the right answers?
Acl sim 1 same. Passed 1000/1000
watson 100% valid
should i book my slot for exam download dumps or should i download dumps first go through them n book my exam slot. pls help me out
Please support to open the ETE file. How can i open that?
1. OSPF neighbors
2. EIGRP troubleshooting
3. ACL 1
4. ACL 2 configuration ( parctice all mods 1,2,3,4 )
Congrats watson and konrad
EIGRP
Q1. The loopback interfaces on R4 with the IP addresses of 10.4.4.4/32, 10.4.4.5/32 and 10.4.4.6/32 are
Ans: R4 and R5 is same AS number but R4 don’t advertised all loopback (10.4.4.4/32, 10.4.4.5/32 and 10.4.4.6/32).
. Answer is The loopback addresses haven’t been advertised, and the network command is missing on R4.
Q2. Which path does traffic take from R1 to R5?
Ans: The answer was that the packets will go R1->R2->R5 AND R1->R3->R5 with equal-cost balancing (sh ip route and you’ll see two possible routes to R5 with equal eigrp metric)
Q3. Router R6 does not form an EIGRP neighbor relationship correctly with router R1. What is the cause for this misconfiguration?
sh run in Router 6
metric weights 0 0 0 1 1 1
so the correct answer is The K values mismatch.
Q4. Study the following output taken on R1:
R1#ping 10.5.5.55 source 10.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.5.5.55, timeout is 2 seconds:
Packet sent with a source address of 10.1.1.1
. . . . .
Success rate is 0 percent (0/5)
Why are the pings failing?
Ans: R1 is advertised network 10.1.1.1 in EIGRP. But R5 isn’t advertised network 10.5.5.5.55 in EIGRP. So the correct answer is The network statement is missing on R5.
ACL2
allow B to access web browser on finance
deny B from access finance
deny any from access finance
allow all to access public web server
i typed last one as access-list 100 permit ip any host 172.x.x.x i think was supposed to be any any
I gave exam today and pass with 925/1000.
OSPF has been Changed
access list from 9tut is same
Eigrp from 9tut is same
Thank you
Is the labs included in the dump?
Guys be carefull there is new 50 questions and there is a newer version of watson i think it has 364 questions
Today i had only 1 of the new 50 ,sorry cant remmber it but it was so easy
And @ the end dump still valid 99.9%
1. OSPF neighbours . Same
2. EIGRP troubleshooting.
Q1= The loopback addresses haven’t been advertised, and the network command is missing on R4.
Q2= The traffic is equally load-balanced over R2 and R3.
Q3= The K values mismatch.
Q4= The network statement is missing on R5
3. ACL 1 . Same .
4. ACL 2 Config . Study all MODs !
Thanks to Watson (whoever you are ?) , and everyone else here who left truthful comments . Good luck to all !
EIGRP new answers.
Goodluck guys...
Simulations:ospf(4 question all same)eigrp:(4 question all same) access list 1:(3 questions all same) acc list2:( mod:3 via web 80)
I am advising all students are candidate to do this exam Cisco to be patient and do good practice for dump questions
Good luck
Inshalah
Its still valid in iraq ?
good luck for all.
This dump is still 100% valid in Jordan bros.
i will exam tommorrow
dumps still valid or what ??
thanks
I can't open dump File with the ETE i have.
an someone help me?
The error message is "This file was created with a newer version of ETE than you have"
pls confirm friends...take care
thanks
same labs ... ACL1 ACL2 OSPF & EGRP
-ACL2
-ACL1 — same
-OSPF — same
-EİGRP troubleshooting —answer change
EİGRP troubleshooting answer =
Q1= The loopback addresses haven’t been advertised, and the network command is missing on R4.
Q2= The traffic is equally load-balanced over R2 and R3.
Q3= The K values mismatch.
Q4= The network statement is missing on R5. Watson and Conrad damps are still valid.
and for eigrp same answer or new come ???
Labs:
EIGRP (t-shoot)
OSPF neighbour SIM
ACL 1 SIM
ACL 2 SIM
Be extra careful when troubleshooting your EIGRP sim they can change it a bit.
Watson 364 is valid
Good luck for all
The only difference is access-list ip
I pass today good luck everyone
This dump is valid 100%
Thank you
OSPF, Eigrp Troubleshooting Sim, ACL1 and ACL2-MOD3
I study 314q dump and just got 2 new questions, i think it would be on 364q dump.
Same OSPF, EIGRP, ACL1 and ACL2 (mod 3) lab sim
Good luck everyone. Do it before 20/8
This dump %98 Valid. Two questions different. One of them SNMP I think answer is only Trap (Selections GET TRAP CAPTURE ..). End one question about encapsulation ppp mode passive..
Lab questions are same :
40 questions
Simulation questions
OSPF (Same)
Q1: There is an area ID mismatch
Q2: There is an OSPF hello and dead interval mismatch
Q3: R1 Fa0/1 configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
Q4: The R3 router ID is configured on R6.
ACL Sim 1 (Same)
Q1: Remove access-group 106 in from interface fa0/0 and add access-group 104 in
Q2: All traffic from the 10.4.4.0 network would be allow to go through
Q3: Hosts cannot connect to Router through s0/0/1
ACL Sim 2
(Modified Host B Modification 4 (Mod 4)) ip changed for Finance server = 172.22.220.17.
EIGRP Troubleshooting Answer:
Q1=the loopback addresses haven't been advertised, and the network command is missing on R4.
Q2=Th traffic is equally load-balanced over R2 and R3.
Q3=the K values mismatch.
Q4=The network statement is missing on R5.
Goodluck Everyone..
Is dump still valid in US. Have anyone taken this exam recently?
Thank and much appreciated!
puditat
dump still valid in Qatar
ospf eigrp(k value mismatch) acl2(host A)
guys try this web address goly.us
good luck to all
Refrance:
1-Netacad Online Material (www.netacad.com)
2-CBT Nugget Videos
3-Sybex CCNA 200-125 study guide
Dumps:
1-Waston
2-Mattehw
3-Gillbest
4-Examtut
Thank you.
I Pass 17-11-2017 Was me second time (Retake)
All Q form dump it Valid 90% some Q it modify only but the concept it's same
Good luck All .
This is my email address : [email protected]
Passed today with 980/1000
Majority of question are from Watson
Good luck guys
364q
still valid in ksa
passed yesterday night
same
acl1
acl2
eigrp
ospf
I couldn't open this ETE file from 1.1.5 version ...
and 5 new LABS
it was at London
THanks!
Danica is right all along.
Find youtube link for Muhamed irshad acl-1 and acl-2 below:-
https://www.youtube.com/channel/UC-hyuQQItN9HfMOIlBaaRzg
Do you mind to type your youtube URL? Thank for updating.
EIGRP, OSPF Troubleshooting, ACL simulator.
got EIGRP troubleshoot, OSPF Troubleshoot, ACL troubleshoot, ACL SIM
I took an exam today, and it was somewhat different.
I would say 10~15% of the questions was different from this one.
If you study well based on this, you should be able to answer though.
Especially Lap question was different.
The financial question, instead of 80 port only, it asked block all. It looks very very similar but one line got changed from the question. I almost got wrong answer.
eigrp lap question.. it was pretty different as well.
new type of frame relay map purpose question... etc...
I passed, but it was more difficult then I expected.
and I just remember... few pictures from dump is wrong. Question itself is wrong. I recall at least 2 questions have wrong image. made me very confusing while studying.
But if you just use this one for studying material, you should be good. Good luck
Eigrp same
Ospf same
Acl same
Acl2 mod3 ip changed.
But exam changing from August 20th
NEW QUESTION LAB EIGRP AND ETHERCHANEL
WATSON QUESTIONS IS 100% VALID
1: Has someone opened these files in the Bluestacks?
2: What is the precise difference between this file, and the files?
thanks
Also, is dump still valid?
Watson and Konrad still valid
labs ACL1 , ACL2 mod, EIGRP troubleshooting and OSPF troubleshooting
just had my exam 960/1000. Your information was very helpful everyone.
Q1:R4 has been incorrectly configured to be in another AS, so it does not peer with R5.
Q2:The traffic goes through R2.
Q3:network command is missing.
Q4:The network statement is missing on R1.
much appreciated!!
Dump is valid (Watson + Konrad)
simulation - ACL1 ACL2 OSP EIGRP
I will go after one week
Thanks for all
Thanks Watson
dump still valid
labs ACL1 , ACL2, EIGRP tshoot , OSPF
Passed today 941/1000
Luckily, all questions are same as Watson 314.
SIM are:
1/ OSPF - T.Shoot (Same)
2/ EIGRP - T.Shoot Answer:
Q1=the loopback addresses haven't been advertised, and the network command is missing on R4.
Q2=Th traffic is equally load-balanced over R2 and R3.
Q3=the K values mismatch.
Q4=The network statement is missing on R5.
3/ ACL 1 (same)
4/ ACL 2 (Mod 3)
Dont forget that 20/08 is the latest day of 200-125.
Goodluck guys.
i cant open the dump
Brock: No the answers are randomised by location so you can't just memorise the location.
EIGRP same
OSPF same
ACL same
ACL2 mod with permit host A
Good Luck!!!!
India
Nov 17, 2017
Report Comment
I have ETE player lic ver but unable to open watson_314q, shows pop up with "Error retrieving key to decrypt file: Wrong login name or password"
Can someone help please
Logout and login back in the simulator. Open the simulator click on the help from the menu bar then click on the about simulator you will see the option to logout click on it and login back.
It worked for me
all question from watson .. just 1 new question from konrad
labs are eigrp – ospf -acl 1 – 2
there was a change in acl 2
allow web browse from host d to finance – all other traffic from host d should be blocked
all other hosts blocked
allow hosts to the other server
good luck for all …
i passed this exam and dump still valid in egypt
ACL1 same
ACL2 same,host D
EIGRP new lap
Can you tell me what are the questions you got for the EIGRP trouble shoot ?
Coz, i check the simulation from other site and the answers there are different from what you guys have given.
So can you provide a link to where ever you did the study for the eigrp simulation,
so i know the answers are 100% correct with the once i got. Thank you//
Can someone tell where I can find the OSPF LAB.
I have the exam this coming Thursday. Thanking you in advance.
[email protected]
there were Syslog, SNMP, Netflow questions (which are not included on Examtut.ete). So better have a look to that one.
9tut.com is also perfect for studying.
Thanks for sharing, and good luck
Thank you so much..all
for the Labs
1- ACL1, OSPF are same as the one you studied from 9tut exactly.
2- ACL2, you have to study modification 3, its 100% same as it with no difference.
3- EIGRP is different, here are the answers of EIGRP.
Q1. The loopback interfaces on R4 with the IP addresses of 10.4.4.4/32, 10.4.4.5/32 and 10.4.4.6/32 are
Ans:
R4 and R5 is same AS number but R4 don’t advertised all loopback (10.4.4.4/32, 10.4.4.5/32 and 10.4.4.6/32).
Answer is
The loopback addresses haven’t been advertised, and the network command is missing on R4.
_______________________
Q2. Which path does traffic take from R1 to R5?
Ans: The answer was that the packets will go R1->R2->R5 AND R1->R3->R5
with equal-cost balancing (sh ip route and you’ll see two possible routes to R5 with equal eigrp metric)
________________________
Q3. Router R6 does not form an EIGRP neighbor relationship correctly with router R1. What is the cause for this misconfiguration?
sh run in Router 6
router eigrp 1
network 10.6.6.6 0.0.0.0
network 192.168.16.0
metric weights 0 0 0 1 1 1
auto-summary
so the correct answer is The K values mismatch.
____________________________
Q4. Study the following output taken on R1:
R1#ping 10.5.5.55 source 10.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.5.5.55, timeout is 2 seconds:
Packet sent with a source address of 10.1.1.1
Why are the pings failing?
A. The network statement is missing on R5.
B. The loopback interface is shut down on R5.
C. The network statement is missing on R1.
D. The IP address that is configured on the Lo1 interface on R5 is incorrect.
A is the correct answer …
wish you all the best.
Best of luck
Passed CCNA R & S on 20-November-2017
Simulations
EIGRP
OSPF
ACL1
ACL2
Note : Be careful and Practice Simulation questions correctly, bcoz modifications will be in there in exam.
Can someone help please
Labs from EIGRP ( Changed ),ACL, ACL-2, OSPF ( Minor Changes )
ACL-2(Modified Host A Modification 3 ip changed for Fin-server = 172.22.225.17
EIGRP
Troubleshooting Answer:
Q1=the loopback addresses haven't been advertised, and the network command is missing on R4.
Q2=Th traffic is equally load-balanced over R2 and R3.
Q3=the K values mismatch.
Q4=The network statement is missing on R5.
ACL Sim 1 (Same)
Q1: Remove access-group 106 in from interface fa0/0 and add access-group 104 in
Q2: All traffic from the 10.4.4.0 network would be allow to go through
Q3: Hosts cannot connect to Router through s0/0/1
OSPF T-Shoot (Same)
Q1: There is an area ID mismatch
Q2: There is an OSPF hello and dead interval mismatch
Q3: R1 Fa0/1 configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
Q4: The R3 router ID is configured on R6.
OSPF - same
ACL1 -same
ACL2 - same - mod (host D)
EIGRP (troubleshooting) - answer changes already there in the comment below
got only 1 question different from dump.
email : [email protected]
Thank you in advance!!!!
Is dump valid in Canada ? any one from Canada took this exam lately ?
Alhmdulilah pass today all Q from watson excpt lab sim ospf eigrp change configration don't forget command show run config to answer proprley.
EIGRP, OSPF and ACL – simulation.
All very much from here.
NO major changes.
Dumps are still valid – the one with 314 questions should be good for preparation.
The 278 questions one has some of them missing in the SNMP/NETFLOW/HSRP.. etc sections.
Good luck.
the dump ete but how can i get the certificate (softcopy)?
when i logged in to Cisco certification it requests me to purchase the kit
what the heck with these greedy people in Cisco even when i m booking for the exam (which is relatively very expensive 295$) it is kept asking me to purchase questions validated by Cisco.. i really believe that they are making more money from Cisco Learning than their Cisco Devices and IOSs.
anyway F... them all
Is there any question about NAT sim Lap or same before only ACL
Is this watson 314q still valid ?
Regards,
Antony
thank you.
The Dump still valid, just 2 new questions
Lab ACL
OSPF
EIGRP changed you need to focus a bit
GOOD LUCK EVERY ONE
passed 110/18/2017
1000/1000
Only dump and 9tut.com Labs
don't waste your time anywhere else
ACL mod 3 change ip add and host
ACL1
EIGRP
Practice and Reading some cisco books
Labs from 9tut ACL1, ACL2 MODE 2, EIGRP 222.
KONRAD is the most updated.
This dump is only the 60% valid. 4 Completely new LAB's and 5 new questions.
Carefull!!!
Questions: Watson Konrad
I scored 1000/1000 today. (ACL sim,simlet - EIGRP Simlet 6 routers - and OSPF simlet)
This dump is valid. I got 1 new questions:
"What setting does not require to be the same on different ports on an etherchannel?"
* speed
* DTP negotiation setting (right answer!)
* duplex
* trunking encapsulation
sorry for my bad english.
My score 1000/1000.
I studied Watson 314. still valid.Lab are
OSPF -same
EIGRP -same (one answer different is K value mismatch)
ACL 2 -Modification 3
ACL 1 -same
Good Luck Everyone.
1 new question
learn OSPF,EIGRP and ACL sims in below posts.
For ACL 2, how do we check the IP address for 3 server and the 4 PC? In exam I can't click to router or switch, only can access to router through CLI.
Please someone help me...
Host C should be able to use a web browser(HTTP)to access the Finance Web Server access-list 100 permit tcp host 192.168.33.3 host 172.22.242.23 eq 80
- Other types of access from host C to the Finance Web Server should be blocked
– All access from hosts in the Core or local LAN to the Finance Web Server should be blocked
access-list 100 deny ip any host 172.22.242.23
(because the requirement says we can not use more than 3 statements so we have to use “any” here for the hosts in the Core and hosts in local LAN)
- All hosts in the Core and local LAN should be able to access the Public Web Server * access-list 100 permit ip any host
(If the question asks this, surely it has to give you the IP of Public Web Server) but in the exam you should use “access-list 100 permit ip any any”
last question is" All hosts in the Core and local LAN should be able to access the Public Web Server "
what is the answer. Ip any any or permit ip any host "Public Web Server iP "
1/ What are three components that comprise the SNMP framework? (Choose three.)
A. MIB
B. agent
C. set
D. AES
E. supervisor
F. manager
Correct Answer: ABF
Two routers named Atlanta and Brevard are connected by their serial interfaces as shown in the exhibit, but there is no data connectivity between them. The Atlanta router is known to have a correct configuration. Given the partial configurations shown in the exhibit, what is the problem on the Brevard router that is causing the lack of connectivity?
Same OSPF,EIGRP,ACL 1&2 . Very easy, don't worry. you gonna pass it.
Thank Prepaway, 9tut and everbody here.
thanks for help me but i have problem in eigrb answer diffrent from friends
Please upload
ete retrieving key to decrypt: Wrong login name or password, any ideas?
The Dump still valid
Lab ACL1 ACL2 OSPF EIGRP on 9tut
Ospf lab Changed
Thank everyone.
Labs: ACL1 , ACL2 ,EIGRP
Huge thank to prepaway and 9tut (labs )
Good Luck !!!
Watson Konrad still valid dumps, Check simulations/lab
* ACL2 —mod3
* ACL1 — same
* OSPF — same
* EİGRP troubleshooting —answer change
Q1= The loopback addresses haven’t been advertised, and the network command is missing on R4.
Q2= The traffic is equally load-balanced over R2 and R3.
Q3= The K values mismatch.
Q4= The network statement is missing on R5
Good luck to the future test takers.
Thanks to 9tut.
Best of luck.
Sims (ACL1, ACL2 with HostB to FWS permit, OSPF and EIGRP the loopback in first question).
GoodLuck Guys
All the questions are from the dump. If you have any questions contact me [email protected]
New Question for snmp security. Answer is Community String
For ACL 2, how do we check the IP address for server and PC? I can't click to router or switch, only can access to router through CLI.
Need help here..how to check those IP in order to set ACL. please help
Are you able to share your youtube link for last minutes revision? The exam time is GMT+8, 30/6/16, 11AM
seems like valid dumps
passed on July 5
Good Luck Guy
please any one send dump to me PDF
[email protected]
Passed today 863/1000 in 7/11/2017
Sim 3 : ACL2, ACL1, EIGRP Troubleshoot, OSPF Troubleshoot (multi choice)
don't study from dump only , because there are some new questions added 8 Q almost ..
im having my exam on nov3. i only have dump of watson. can anyone send me latest pdf file? please please! [email protected]
958/1000
You may take dump
dump valid 100%
just EIGRP lab change the teleology
09-11-2017
ACL was exactly the same for me
EIGRP no configs just verifying and answering questions
ACL
I remember there is one question with a bad image, it is about serial connections, the valid image shoes up/down for the interface so it is obviously a layer 2 issue, the answer for the question on the dump are the answers for the test.
passed 1000/1000
labs
2 acl
1 ospf
1 eigrp
total question is 40.
Watson is still valid in NJ USA. Just took the test and failed with 750/1000. I should have went here first and took some nites on MO JEDY answers. Smh
A help from me too..for packet tracer..
http://ipcisco.com/rip-configuration-with-packet-tracer/
i will appreciate that
Thanks
all question from watson .. just 1 new question from konrad
labs are eigrp – ospf -acl 1 – 2
there was a change in acl 2
allow web browse from host d to finance – all other traffic from host d should be blocked
all other hosts blocked
allow hosts to the other server
good luck for all …
dump is valid. but there are few questions in multi answer that are not in dump. so better to explore about netword devices security.
acl1
acl2 mod 3 ip change
eigrp same
ospf same
goodluck guys
There were 36 questions plus 4 sims: EIGRP, OSPF, ACL1, ACL2 (all from 9tut).
30-40% questions are out of dump.
Must study ACL, OSPF, EIGRP sims at 9tut.com
Thanks
passed my exam in USA
this is valid but also read Konrad 338 Questions
dont for get labs. if you cant do labs dont go for exam
labs are .
EIGRP
OSPF troubleshooting which was difficult
ACL
RIP trouble shooting
good luck
I am going to take my CCNA exam on coming Tuesday!
I just wana know if Tab and ? (question mark) work in simulation questions ? Any other advice would be highly appreciated.
Thanks
Still dump is valid!!
Good Luck!!!
LABS all the same
ACL1
ACL2
EIGRP
OSPF
Premimum dump is valid
Simulation:
ACL2
ACL1
EIGRP
OSPF
GOOD LUCK
Passed on 19/10/2017 with 931\1000.
Studied only dump and ACL1, ACl & EIGRP
Good Luck!
Simulation Questions were ACL 2 modification 3(change in IP address), ACL(Same as in 9tut) , EIGRP config (AS 122)
labs Eigrp 23 (212), ACL 1 and ACL 2.
some people say the dumb is not availed and there is 50 question new
please if any one take this exam this week or will take it soon before 11 August
please tell me if it availed or not
922/100
980/1000
ACL Sim 1 (Same)
ACL Sim 2 (Modified Host A allow,other block)
EIGRP Troubleshooting (Modified IP/answers)
OSPF (Modified [R2/R3 Equal load, K Values)
All dumbs 100 valid, Watson+Konard :)
i need to do the exam in 18.11.2017
thanks
Could you please share what is the change of lab simulation ?
thanks
I passed the exam this morning. I scored 980. This dump is valid. just be careful, the eigrp lab is a different and the ACL also.
Good luck to the others
Good luck to all!
Sim x 4: ACL ACL1, EIGRP Troubleshoot, OSPF Troubleshoot (multi choice)
ACL-1(same)
ACL-2(mod-3 & ip chanaged)
OSPF(same)
EIGRP(with new answer)
Good Luck!
dump still valid but there's some new question that not available on dump or examtut 5-7 question i guess, and compared to examtut i suggest you take this one.
lab sim go for 9tut.com remember not to memorize the ip address on it cause it will change
good luck.
I tried all the other ways and they're all expensive.This is the cheapest way I found on apple devices, not sure about the Windows devices.
%100 valid
Passed the exam today score 863/1000
Watson and Konrad still valid
labs ACL1 , ACL mod, EIGRP troubleshooting and OSPF troubleshooting
The Dump still valid
Lab ACL1 ACL2 OSPF EIGRP on 9tut
Thank everyone.
i will appreciate it a lot abit desperate.
- This dump is 100% Valid in Egypt, but the answers order is changed in almost all questions, so you have to understand the answers.
Here’s my advice for everyone to PASS this exam:
- Download the book: (How to master CCNA) nicely and simply explaining things - good for studying CCNA in general.
- Check out the serious of videos for Ahmed Nazmy (in Arabic) on youtube for this dumb questions and answers, helps alot.
- Just like any other dump, I used this method to study it:
-Go through the whole dump 314 questions, if you answer a question alone then go next, if you fail to answer a question alone, then MARK IT , then keep going, do this until you finish the whole dump questions.
-Once finished, try to answer the MARKED Qs alone, you will do better this time, and keep the failed Qs MARKED to review them again.
-Repeat until you finish the WHOLE dump ALONE, then you're ready for the EXAM - good luck, and don't forget Doaa ;)
- Labs are the most important, and these what I have got in my exam:
OSPF , ACL1, ACl2, Eigrp, Eigrp troubleshooting.
(Remember to study all labs with its modifications (Mods)) , it happened to me that I didn't get the main ACL2 question otherwise I have got mod3 so make sure you study them all.
Make sure you solve ALL labs alone so you can do alone in the EXAM, at least solve them twice alone , and use packet tracer to open the labs and to actually practice the real lab simulations, when you can solve them all alone then you’re ready for the labs
If you have learned and understood CCNA in total, then you are going to need only 7 days to get prepared well for the exam.
Good luck everyone.
[email protected]
i will make exam tommorrow
dumps still valid ??
Regards
EIGRP Troubleshooting Sim (Changed)
1) Answer: The loopback addresses haven’t been advertised, and the network command is missing on R4.
2) Answer: The packets will go R1->R2->R5 AND R1->R3->R5 with equal-cost balancing (sh ip route and you’ll see two possible routes to R5 with equal eigrp metric)
3) Answer: The K values mismatch
4) Answer: The network statement is missing on R5
Just be careful and see what configured on all routers.
OSPF Neighbor Sim (same)
Access List Sim 2 (modification 3)
Access List Sim (same)
Just follow dump and 9tut.com, Goodluck!
EIGRP troubleshoot Sim ,, configuration on router had been changed ,
********************************
***********
EIGRP troubleshoot changing All question.
Q1. The loopback interfaces on R4 with the IP addresses of 10.4.4.4/32, 10.4.4.5/32 and 10.4.4.6/32 are
Ans: R4 and R5 is same AS number but R4 don’t advertised all loopback (10.4.4.4/32, 10.4.4.5/32 and 10.4.4.6/32). Answer is The loopback addresses haven’t been advertised, and the network command is missing on R4.
Q2. Which path does traffic take from R1 to R5?
Ans: The answer was that the packets will go R1->R2->R5 AND R1->R3->R5 with equal-cost balancing (sh ip route and you’ll see two possible routes to R5 with equal eigrp metric)
Q3. Router R6 does not form an EIGRP neighbor relationship correctly with router R1. What is the cause for this misconfiguration?
sh run in Router 6
router eigrp 1
network 10.6.6.6 0.0.0.0
network 192.168.16.0
metric weights 0 0 0 1 1 1 ******************
auto-summary
so the correct answer is The K values mismatch.
Q4. Study the following output taken on R1:
R1#ping 10.5.5.55 source 10.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.5.5.55, timeout is 2 seconds:
Packet sent with a source address of 10.1.1.1
. . . . .
Success rate is 0 percent (0/5)
Why are the pings failing?
Ans: R1 is advertised network 10.1.1.1 in EIGRP. But R5 isn’t advertised network 10.5.5.5.55 in EIGRP. So the correct answer is The network statement is missing o
thanks in advance
EIGRP AS 121, ACL-1, ACL-2 MOd 3
Passed today Score 917/1000. Simulation ACL1,ACL2 mod(4),EIGRP with AS no.221. Got 51 questions. Thank you all :)
Thanks!
OSPF T-shoot
EIGRP T-Shoot
ACL SIM 1
ACL SIM 2 MOD 3
passed today .
good luck for all
Egypt, Passed today with 922/1000
Thanks Comments
dump is 100% Valid and there are new questions in Dump Konrad
pls confirm this file is valid until today please
i passed today
thank you allah
الحمدلله الاختبار جميل وبسيط
i am from vietnam and need your help,
my email: [email protected]
dump =364 questions
-ACL2 —mod3 (only ip change)
-ACL1 — same
-OSPF — same
-EİGRP troubleshooting —answer change
EİGRP troubleshooting answer =
Q1= The loopback addresses haven’t been advertised, and the network command is missing on R4.
Q2= The traffic is equally load-balanced over R2 and R3.
Q3= The K values mismatch.
Q4= The network statement is missing on R5
good luck guys…
Simulations x 4.
EIGRP, OSPF ACL1 and ACL2 from 9tut.
Dump is valid but, you need to know hsrp, syslog, snmp, and netflow questions. 1 etherchannel question too. Sims: ACL,1,2, EIGRP LAB Question (from 9tut.
Thanks 9tut, examtut and Watson 310q.
Sims: 9tut acl1 acl2 eigrp222
I passed today with 931/1000 score. SIM labs are EIGRP, ACL1, and ACL2 (the same 9tut).
Thank Waston and 9tut for supported.
1 lab access-list 2
1 Access List Sim
1 ospf troublershooting Sim
1 EIGRP troubleshooting Sim
The dump is still valid.
one question about ethnet-chanel is added
Thank 9tut.
1 New question from Etherchannel
there's 4 labs (Ospf, Eigrp , ACL1, ACL2)
This dump is 100% valid
passed last Tuesday,
got 1000 score, dump is still valid
good luck y'all
Labs: EIGRP, OSPF, ACL1 and ACL2
i have exam in few days
Hoy aprobé, 986/1000, gracias a Watson, Examtut y 9tut.
3 laboratorios:
CCNA Access List Sim 2 (Mod 2): http://www.9tut.com/78-ccna-access-list-sim-2
CCNA Access List Sim: http://www.9tut.com/70-ccna-access-list-sim
CCNA EIGRP LAB Question (AS 12): http://www.9tut.com/64-ccna-eigrp-lab-question
Tambien 3 drag and drop.
Suerte a todos!!!
I thank everyone for sharing all these notes.
I will pass my exam this Friday. Please, does the questions and labs will be the same or the IP @ will be different ? Thank you
Passed on 19/10/2017 with 972\1000.
Studied only dump and ACL1, ACl & EIGRP
Good Luck!
If there is any news in the simulations i studied acl 1 acl 2 eigrp please need help
LAb: Eigrp - ACL1 - ACL1
there's 4 labs (Ospf, Eigrp , ACL1, ACL2)
only one configuration in ACL2 ,
[email protected]
there's 4 labs (Ospf, Eigrp , ACL1, ACL2)
only one configuration in ACL2 ,
other labs is only hotspot.
before enter the exam make sure to check other dumps just to be sure like (kornard and examtut)
for labs only 9tut
If anyone from PAKISTAN need any kind of help regarding exam and on fee DISCOUNT on exam then email me at [email protected]
thanks alot to prepaway
ospf, eigrp, acl1, acl2
980/1000
This dump is valid 98%
two new questions
laps
1-Acl 1 same
2-Acl 2 Mod 3 (Host C should be able to use a web browser(HTTP)to access the Finance Web Server access-list 100 permit tcp host 192.168.66.3 host 172.22.167.17 eq 80 – Other types of access from host C to the Finance Web Server should be blocked – All access from hosts in the Core or access-list 100 deny ip any host 172.22.242.23 (because the requirement says we can not use more
local LAN to the Finance Web Server should be blocked than 3 statements so we have to use “any” here for the hosts in the Core and hosts in local LAN) – All hosts in the Core and local LAN should be able to access the Public Web Server * access-list 100 permit ip any host (If the question asks this, surely it has to give you the IP of Public Web Server) but in the exam you should use “access-list 100 permit ip any any”)
3-Eigrp K value part
4-Ospf same
there are few question need to be update
check latest updates before you give your try! good luck
I pass 902/1000 in Cambodia
Is there any changes in dump > waht about sims ?
I'm going to get my exam after two days .
Please provide me with the latest dumps - [email protected]
Thanks,
Nir
don't worry guys This dump is still vaild 100 % there are 40 question only and for lab study ACL1 ACL2, EIGRP Troubleshoot, OSPF Troubleshoot and you will get only two labs for me I got ACL1 and OSPF Trubeshoot..
pass today 16/4 ((958/1000))thanks to watson & examtut .....from egypt ....tanta
eigrp 122 ((Acl 1 & Acl 2))
1 question about etherchannel DTP SETTINGS
http://www.9tut.com/eigrp-troubleshooting-sim#more-2252
Thanks in advace
Special thanks for eng.Ahmed nazmy (his videos on YouTube) and islam.
It was very hard first moments in exam. I was very nervous. But after that every thing going very well.
51 questions in 120min.
This dump is valid 100%.
Simulation Questions were ACL 2, ACL(Same as in 9tut), EIGRP config (AS 2) and make advertise the network between this router and another router.every thing easy just with little modifications.
Good luck every one :)
Please, can you send me the last dump [email protected]
I will passe my exam CCNA this friday.
Thank you.
Simulation acl1 , acl2 , eigrp 212.
Thanks
Passed le 15-11-2017 , Dump still valid ,no change in the labs ,GOOD LUCK EVERY BODY.
Lab ACL 1 same, ACL mod 3 IP change, EIGRP TSHOT change choice (Missing loopbacks R4, Load balance R2 & R3, K values, Network Missing R5), OSPF Neighbor same and 1 drag and drop (Router,DTE,DCE,CSU/DSU,Digital Line,WAN Provider).
passed
dumps valid but two new labs OSPF, EIGRP included..
total questions 53, configurations lab 2
multiple choice question labs 3
WATSON and 9TUT LABS - EIGRP ACL1 ACL2
There are couple of new question dont remember those but there were 3-4 questions.
Go for 9tut (questions and sims) and watson dumps thats more than enough.
This dump is not valid anymore.
There were ten new question in my test including new sim.
Sims were ospf,rigor,acl1,acl2 and the new ospf sim.
I nearly failed my exam.
845/1000.
Some of the question is valid but don't trust everything on dump
ACL,ACL and eigrp 112
only one question new as following
Question:
A network administrator creates a layer 3 EtherChannel, bundling four interfaces into
channel group 1. On what interface is the IP address configured?
A. the port-channel 1 interface
B. the highest number member interface
C. all member interfaces
D. the lowest number member interface
Answer: A
thanks..
Thanks
Simulations
ACL 1
ACL 2
OSPF
EIGRP
Passed today, DO NOT IGNORE SIMULATIONS.
Cheers from Bhopal
Piece of advice; For the sims, read and understand all tasks and mods because they can change just a section of the question. You can be confused if you cram the modifications so try to understand.
Special thanks for eng.Ahmed nazmy (his videos on YouTube) and islam.
It was very hard first moments in exam. I was very nervous. But after that every thing going very well.
51 questions in 120min.
This dump is valid 100%.
Simulation Questions were ACL 2, ACL(Same as in 9tut), EIGRP config (AS 2) and make advertise the network between this router and another router.every thing easy just with little modifications.
Good luck every one :)
Goodluck
which qustion in dump refer to LABs in exam
send me answer on email
[email protected]
This dump is still vaild but there are 8~10 questions that dump doesn't cover.
ACL1 ACL2, EIGRP Troubleshoot, OSPF Troubleshoot
Thank you, in advance!
i took the test yesterday. The Sim were ACL,ACL2 and EIGRP as 112.
Good luck !!
Simulation Questions were ACL 2 modification 3(change in IP address), ACL(Same as in 9tut) , EIGRP config (AS 122)
wasan + 9tut (Lab ACL 1,2 & Eigrp2) & ether-channel from 9TUT
I pass today 27-04 849
Does the dump still valid? coz i will take exam 2moro :D ???????
Pass today with 980/1000.
The exam is very easy , all question from dump.
Labs: OSPF,EIGRP AND ACL are the same on other dump, for ACL2 look modification 3.
Good luck!!
Today i have pass cisco exam with 961/1000
Watson/konrad still vaild dumps with 100%
there is 40 qustion with 4 labs
ACL1..ACL2 mode 3 only for ip change..OSPF mcq..EIGRP MCQ
GOOD LUCK FOR EVERYBODY..
Score 902.
Thanks guys.
From VietNam
passed today. Dump is 100% valid.
Study Watson and 9tut.com.
Labs from 9tut: eigrp, acl1,acl2 but try to understand it as there are some modifications in the task (IP addresses and networks to be added). I strongly reccomend you to check whether you placed the correct config by pings. I configured ACL on a different device and found it out by final tests (ping to financial server was not successful) so I had to correct it ...
Wish a good luck to all of you;)
Simulation EIGRP, ACL 1,2
Simulation EIGRP, ACL 1,2
Thanks
Thank you
All : 40 => Sim 4 [ACL1, ACL2, Eigrp, OSPF]
1 New question : [ same as Tran Man Dat told ]
2 Different question : [ answer change 1 and detail in exhibit change 1 ]
I think if you carefully read it, Watson will be still valid for you.
Good luck.
there was one new question about port channel and the ACL simulation was with modification 3 from 9tut.com
all the best to all rest of my fellow networkers.
Thanks to 9tut ,watson,examtut,konard,jeremy,imran (Youtube) and cisco press....Please go through konard to get 1000.Sims are slightly changed(ips).All the best
Thanks GOD!!!
In ACL2-mode ,how do i check the IP address for server and PC? i'm first time taking exam.
I just notice i can click on CLI only and PC with web browser only.
HElp helo
all questions are in dump except only one question.
good luck all.
please .......
Watson still valid.I studied Watson 314, Examtut 278, Konnrad 338.
Lab are
EIGRP Troubleshooting
OSPF - Same
ACL1 - Same
ACL2 - Modification 3 with permit Host D
EIGRP Troubleshooting Answer:
Q1=the loopback addresses haven't been advertised, and the network command is missing on R4.
Q2=Th traffic is equally load-balanced over R2 and R3.
Q3=the K values mismatch.
Q4=The network statement is missing on R5.
Good Luck Everyone!!!
Sri Lanka
best wishes
7/5
I guess someone who has written the exam can answer this better? Much appreciated!
Special thanks for eng.Ahmed nazmy and eng. ayman el shawadfy
It was very hard first moments in exam. I was very nervous. But after that every thing going very well.
51 questions in 120min.
watson dump is valid 100%.
Simulation Questions were ACL 2, ACL(Same as in 9tut), EIGRP config (AS 2) and make advertise the network between this router and another router.every thing easy just with little modifications.
Good luck every one :)
can you tell me where do you get the new questions .. i have Watson + 9tut labs , anything else ? :)
There is only one new question and one question in the dump is answered wrong.
Lab is ACL 1, ACL 2 and EIGRP.
the wrong answered question was using the same subnet for both serial and Ethernet interfaces. it will not function correctly.
I passed today 986/1000 score!
Thanks Watson 100%, 9tut
Labs are ALC1, ACL2, EIGRP 222
Dump is valid (only 2 new questions out of "Watson" dump) may be in "Konard" i didn't revised it,only studied "Watson"
Laps:
ACL1 + EIGRP+ ACL2 Mod.(3)
Modified Ips in ACL2 lap than in dump:
Fa 0/0 192.168.81.254 for "Hosts"
Fa 0/1 172.22.47.30 for "Servers Lan"
S 0/0 192.168.3.65 for "Core"
Host c:192.168.81.3
Finance web server 172.22.47.17
Simulation acl1 , acl2 , eigrp 22.
sim questions are Eigrp 12 + ACL +ACL2 (9tut.com)
I passed today 960/1000 score
Can someone provide me the simulated in .pdf or dowload ete current player?
email: [email protected]
thank you!
This dumps still valid the labs ACL1,ACL2,EIGRP Troubleshoot sim & ospf sim.
Good luck guyz
Passed yasterday with 931/1000
Thanks to Watson Konard
Thank you to God and Friends
All questions are from dumps and stick with 9tut for practical questions
Just EIGRP Troubleshooting- k value mismatch
Focus on lap questions: EIGRP, ACL 1, ACL 2 (change ip)
51 questions
90 mins
Be aware!!! you mush go through each question carefully as there is no back button on the test. Paseds today with 973/1000. Good luck and thank you to prepaway and 9 tut.
This and 9 tut is all you need to pass the exam. missed 1 questions because I forgot the answer.
Watson
examtut
Matthew from prepaway.com
labs from 9tut.com
ACL 1. ACL 2 (modification 3) . EIGRP (22)
examtut, Watson and Konrad.
laboratory from 9tut: eigrp, acl1,acl2
Few new questions sims are Acl/ Acl2 Eigrp in 9 tut
This is my email address : [email protected]
Score 986/1000
I studied watson and 9tut labs and new questions.
Acl1, acl2 and eigrp 212
i passed yesterday with 903 dump still valid.
Can you guide me how many simulation questions asking for exam???
VALID DUMP 100%,Passed 930, Yesterday January 2nd.
EIGRP lab is the same like 9tut , ACL 2 modification 3, ACL smilet.
Good luck everyone.
thank you
pass tody score 941 !!!!
OSPF EIGRP ACL2 MOD 3 and ACL1
Special thanks for eng.Ahmed nazmy and eng. ayman el shawadfy
It was very hard first moments in exam. I was very nervous. But after that every thing going very well.
51 questions in 120min.
watson dump is valid 100%.
Simulation Questions were ACL 2, ACL(Same as in 9tut), EIGRP config (AS 2) and make advertise the network between this router and another router.every thing easy just with little modifications.
Good luck every one :)
this dumb is still valid but you must study mathew dump also,there is more question from it
LABs: EIGRP, ACL, ACL2
study hard dont worry
any question, contact with me
Email: [email protected]
Whatsapp: +201095478617
Watson dumps for mcqs and drag n drop questions
9tut for labs ( EIGRP , ACL1 and ACL2 )
Dont waste your time anywhere else
lab ( access list 1 and 2 + eigrp 2 )
pass today 1000/1000 الحمد لله
I passed today 960/1000 score
Keep calm and atteation with the ip' of labs because is different.
Thanks for God
BRAZIL
[email protected]
Thank you !
what are new lab questions
dump is 100% valid
goodluck
[email protected]
Thanks!
Alhamdullah i passed on 12/1/2017 with 961/1000
Dumps watson 364 q is valid 100%.
40 questions
Simulation questions
OSPF (Same)
Q1: There is an area ID mismatch
Q2: There is an OSPF hello and dead interval mismatch
Q3: R1 Fa0/1 configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
Q4: The R3 router ID is configured on R6.
ACL Sim 1 (Same)
Q1: Remove access-group 106 in from interface fa0/0 and add access-group 104 in
Q2: All traffic from the 10.4.4.0 network would be allow to go through
Q3: Hosts cannot connect to Router through s0/0/1
ACL Sim 2
(Modified Host B Modification 4 (Mod 4)) ip changed for Finance server = 172.22.213.17
EIGRP Troubleshooting Answer:
Q1=the loopback addresses haven't been advertised, and the network command is missing on R4.
Q2=Th traffic is equally load-balanced over R2 and R3.
Q3=the K values mismatch.
Q4=The network statement is missing on R5.
Simulation acl1 , acl2 (mod4) , eigrp 221.
ACL1 ,ACL2 ,Eigrp
Know your work guys! used these dumps at the end of my studies and was getting between 75% and 85% first time doing them. NO BACK BUTTON OR ABILITY TO REVIEW QUESTIONS IN EXAM!!
100% valid, useful and effective,
4 sims, tab shortcuts work but only if you try after ?, and then try tab in global conf,
eigrp 112, acl 1 and acl 2 on 9tut thanks to them it works you all can rock it, and yes please buy the ete player it is a worth investment. acl sim 4 is 5 line design. have inaccurate details... dont remember a lot just make sure you are clear for acl concept and eigrp needs command "net 0.0.0.0 255.255.255.255" for 1000 marks. acl now also needs sh ip access-list and sh access-list command.
Still Valid, I passed my exams 945/1000
Watson + 9tut for some extra questions
Labs ACL1, ACL2 Mod 2, EIGRP 222
917 dum still valid ..labs were ACL1, ACL2, EIGRP 212, thank you all .
an some one send me 200-125 exam dumps in pdf
mail; [email protected]
sims (ACL, Eigrp) are in www.9tut.com
ACL1, ACL2(mod 3), EIGRP
Watson dump valid 100%
but 1 new quest in Matthew dump
so you should read Matthew dump for some new questions
Thanks alots!!!
i got 51 questions with 3 sims. 1)EIGRP AS23 2)acl 1 3) acl 2.
EIGRP 23 ,ACL1 ,ACL2 IP address are changed
Passed on 08/10/2017 with the score of 972/1000.
This Dump is 100% valid. Labs are valid but with some modifications in names,numbers and IPs but u can understand from 9tut (EIGRP,ACL1,ACL2 mod3) got 52 question only 2 new questions out of Watson dump u can see it from here:
http://www.9tut.com/new-ccna-new-questions-2
Just study watson, examtut and 9tut its more than enough.
Thank you watson, examtut and 9tut.
good luck for all :)
Admin, Could you please update comments quickly?
Ty
Is this Dump still valid in New Zealand??
Please Let me Know.Thanks
Many Many thanks To ALLah
I have passed today with 958/1000
EIGRP with Mobification ,ACL1 same as 9tut ,ACL2 IP address are changed.All dums are from watson, examtut
This dump still valid
Have some new question
ACL 1 . ACL 2 host B mod 3 , EIGRP lab
Thank you 9tut and Watson so much
watson's Dump 100% valid and its more than enough..
there was 51 questions including 3 simulations [EIGRP AS 212 ,ACL1, ACL2(mod 3)]only one new question on etherchannel.
Thank you watson dump and http://www.9tut.com/
I passed today score 1000/1000, the dump is valid and sim eigrp 122,acl1,acl2 mod3
but there was a new question about ospf not in the dump asking about advertise all networks to ospf area 0
thanks 9tut and watson
thankx to Watson and 9TUT.
Use Watson dumps, Konrad dumps and a dump ETE which was mailed to me buy someone on the internet.
There were a lot of new questions. I think around 10 to 12. I don't remember all though.
For people who are mugging the dumps, you will fail. Definitely. Because Cisco is not twisting the questions. Instead of asking you the answer, they give the answer and ask you the question. So make sure you actually do know the concepts. If all you're doing is mugging, don't give the exam. Save your money.
I don't remember all the questions, but here are few I remember.
1. What command will create a DHCP pool?
Ans: # ip dhcp pool Dhcp_POOL
2. What subnet mask is used for IPv6 in Point to point links?
Ans: /127
3. Something related to translation if ipv4 to ipv6.
Ans: NAT46
4. What levels of logging will be enabled if we type "#Logging warning" command? (Question similar to this)
Ans: 0 - 4
Please note:
Question 2 is not the whole question. This was a part of the question that I remember. This was a question with "Choose Two/Three" answers and this is one part of it.
Question 3, I don't remember the question, but it was something to do with translation of ipv4 to ipv6 and the answer is definitely NAT46. Remember one thing.
IPv4 to IPv6 Translation = NAT46
IPv6 to IPv4 Translation = NAT64
This is all I can remember.
Here is all the dumps, PDF and labs I used to prepare. :)
http://goo.gl/gbldYO
You can always contact me for any questions :) Please do not email to mail you dumps and all as I've attached it in the link above.
My Email:
[email protected]
Yes, that is a real email address.
Or you can find me on Telegram App for doubts:
https://telegram.me/AnonUse
Good luck for your exams :)
and ospf and EIgrp .. takecare Eigrp request no3.3 no neighbor between R1 And R6 because network at router 192.168.6.. at 6 are not advertised if it's advertised then Answer is K vaules no match
thanks in advance
Lab - ACL2
Simlet - EIGRP, OSPF, ACL1
Two new questions are present in KONRAD ETE file.
9tut website is a very good study guide.
update plz.thanks
I would go for mine tomorrow.For the EIGRP Lab, was it a different one, or just some changes ?
sim: ACL; ACL2 and EIGRP ( change IP)
a valid dump watson + some new question: SMMP : MD5
ethernet channel: mode passive
Thanks
Is dump still valid?
Lab questions are, ACL , EIGRP and SIM.
watson+9tut
Passed today 6jun 972/1000
Laps :ACL1-ACL2-EIGRP
dump watson last 30 q konrad
lab ( acl 1 acl 2 eigrp 2 )
http://www.9tut.com/70-ccna-access-list-sim#more-39
http://www.9tut.com/64-ccna-eigrp-lab-question#more-29
http://www.9tut.com/78-ccna-access-list-sim-2#more-41
got 958
http://www.ccnalearn.cf/simulation.html
Exam taken on 28-Jul in SG.
only
EIGRP troubleshoot Sim ,, configuration on router had been changed ,
********************************
***********
EIGRP troubleshoot changing All question.
Q1. The loopback interfaces on R4 with the IP addresses of 10.4.4.4/32, 10.4.4.5/32 and 10.4.4.6/32 are
Ans: R4 and R5 is same AS number but R4 don’t advertised all loopback (10.4.4.4/32, 10.4.4.5/32 and 10.4.4.6/32). Answer is The loopback addresses haven’t been advertised, and the network command is missing on R4.
Q2. Which path does traffic take from R1 to R5?
Ans: The answer was that the packets will go R1->R2->R5 AND R1->R3->R5 with equal-cost balancing (sh ip route and you’ll see two possible routes to R5 with equal eigrp metric)
Q3. Router R6 does not form an EIGRP neighbor relationship correctly with router R1. What is the cause for this misconfiguration?
sh run in Router 6
router eigrp 1
network 10.6.6.6 0.0.0.0
network 192.168.16.0
metric weights 0 0 0 1 1 1 ******************
auto-summary
so the correct answer is The K values mismatch.
Q4. Study the following output taken on R1:
R1#ping 10.5.5.55 source 10.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.5.5.55, timeout is 2 seconds:
Packet sent with a source address of 10.1.1.1
. . . . .
Success rate is 0 percent (0/5)
Why are the pings failing?
Ans: R1 is advertised network 10.1.1.1 in EIGRP. But R5 isn’t advertised network 10.5.5.5.55 in EIGRP. So the correct answer is The network statement is missing on R5.
********************************************
search for me on FaceB/id.ramy
hope success for all Inshallah <3
Thanks to Allah then jermy & Prepaway
This dump is valid labs are Acl1,Acl 2 mod3 , Eigrp.
This dump is still valid. I passed today. 945/1000.
Labs eigrp. Acl1.Acl2. 1 new questions egypt
ACL1 ,ACL2and Eigrp
Passed today
This dump is 100% valid
1Q new
sims (ACL1 & ACL2 & Eigrp AS 212)
good luck for all :)
2/10/2017
sim are: EIGRP , ACL1 , ACL2 mod 3
ACL1 and ACL2 and Eigrp23 labs in the site 9tut.com
Thanks examtut, Watson and Konrad.
laboratory from 9tut: eigrp, acl1,acl2
Very Important
Study last 40 Questions of Konrad dump.
All a new Questions already there.
Many thanks to Watson & 9tut & examtut
Dumps from Watson are walid and ACL1 and ACL2 and Eigrp were the labs got in the test
Simulation acl1 , acl2 , eigrp 212.
Pakistan
1 It about SNMP-Answer is "community string"
2 It about ospf.What wildcard mask and ip addresses need pass in the command network that all ip addresses will pass in area 0.Answer is "network 0.0,0.0 255.255.255.255 area 0"
3 Its about ethernet channel.Question was : what ip addresses will pass if four interface will be in one aggregation." I think answer is the highest ip addressee
4 I diddnt remember
About Lab.All lab in 9tut is valid but when i troubleshoting in ospf I thought that there was a network 192.168.41.0.This network wasnt be in the topology,i was write "no network 192.168.41.0"
About all exam in one question there was another ip addresses not so in the dumps.The valid answer in dumps was not valin in real exam,be carefully.passed with 1000 score.
ACL1 ACL2 mod3 EIGRP
review dump.ete dumps to get a perfect score
[email protected]
please any one send dump to me PDF
[email protected]
thank you in advance for cooperation
Thank for prepaway.
Dump still valid in Israel.
Passed on Thursday with 849\1000.
Studied only dump and ACL1, ACl & EIGRP.
Two new questions.
Good Luck!
Many Many thanks To ALLah.
I passed today with 958/1000
dumps are 100% valid
EIGRP with Mobification ,ACL1 same as 9tut ,ACL2 IP address are changed ,Mod 3 as 9tut,got 51 qestoin.
email me my id [email protected]
Gave the exam today and passed with 958.
51 question (which included 3 Simulations –> EIGRP , Access List & Access List (ACL) 2 with modification 3).
Duration - 120 mins
Study materials used –
1. Studied CBT Nuggets series of ICND1 & ICND2 for about 20days. Jeremy (the trainer) was awesome and once done with the series a person would have a very good understanding on Networks. I could answer 60-70% of dumps questions with just learning through videos.
2. 9tut.com (http://www.9tut.com/category/ccna-lab-sim) practiced all the Simulations using packet tracer. I am pretty sure that if you would learn networks through cbt nuggets all the simluations could be practiced in few hours (2-3 hrs. ;) ).
3. And some new questions provided @ 9tut -> http://www.9tut.com/new-ccna-new-questions-2
4. Finally, Mr. Watson’s dump which really helped as all questions except 1 were from dump.
Coming back to the exams
---------------------------
I was asked 51 questions as mentioned before which had 3 simulations included. I would like to give you a tip if in cause you do a mistake which even I did. In Access List 2 (http://www.9tut.com/78-ccna-access-list-sim-2) as you know we have to apply the command “ip access-group 100 out” on f0/1 but I applied it on f0/0 by mistake. Now this problem can be easily resolved by using the command “no ip access-group 100 out” but the problem I faced is that CISCO DOESN’T ALLOW “NO” commands. I tried removing the access-list also by using “no router access-list…..” but even this didn’t work.
Now, considering the scenario given if we apply the access list to f0/0 and leave it as it is then also it’s not a problem as it doesn’t block any of our configurations. You can keep it as it is and apply the access list to f0/1 and all your given requirements in the questions would work absolutely fine but I am not sure if CISCO would deduct points for that or not.
So, what I did was just this – “copy startup-config running-config” (not and “copy running-config startup-config”) and what it did was the startup configuration came back i.e., the initial configuration provided with the question. After that it was simple, I just created the access-list again and applied it to f0/1.
Exams has 3 sections –
1. 15 mins of information on how to write the exams, rules, etc. and I recommend all of you to read it without fail.
2. The exam for 120 mins (I forgot to mention one more thing, there is also a comment option with every question which allows you to input any comments / feedback regarding that question. Not sure how helpful it would be but can be used if required as it would be read by the CISCO people after few days of exams and if required they might call / mail you too. :p)
3. Survey on how the exam was.
I know it’s a very big post but could be helpful for those appearing for the exams in the upcoming days. :) All the best. I will soon be launching a website for those who wish to learn CCNA and appear for the certifications. Would post the URL on this forum.
For any doubts you may drop me a mail and I will try my best to clear any doubts if I can ;)
Mail : [email protected]
-there are aboute 7 new question (2 etherchannel-ospf -2 ospf id -dtp setting)
labs were ACL2 and EIGRP
For your informaiton, all questions except for simulation and below one were from Watson. my simulation question of ACL2 was modification 3(however, workstaion was changed from C to B). And, orders of all muliple choices are mixed, not following orders from Watson dump.
(A New Question)
What setting does not require to be the same on different ports on an etherchannel?"
* speed
* DTP negotiation setting (right answer!)
* duplex
* trunking encapsulation
GOOD LUCK!
passed today(11.8.15) with 1000/835...close call really :)
ACL1, ACL2(MOD 4) and EIGRP(122)
did all self-study including JEREMY vdos, online material, notes and finally watson dumps.
BEST OV LUCK all you cisco future :-)
Tomorrow will have exam...
Passed on 19th June got 1000/1000. Simulation ACL1,ACL2 mod(3),EIGRP with AS no.12. Got 51 questions.
Dump Still valid
Sim : ACL1,2 - EIGRP 12
No New questions
I passed today 972/1000 score!
Thanks Watson 100%, 9tut
Labs are ALC, ACL2(MOD3), EIGRP 2...
Labs:EIGRP , ACL1 like 9tut and ACL2 modification3 instead of host C there were host B
https://www.vumingo.com/exam-testing-engine.html
The labs need to study what?
My proof is marked for early February
Hug and Success to all.
Ass:Bruno
pass today
EIGRP lab and ACL same but ip changed
lab: EIGRP, ACL and ACL2 From 9tut.com
and Watson valid 100% except 2 questions
Network Admin creates a layer 3 Etherchannel, bounding 4 interfaces into channel group 1. On what interface is the IP address configured?
A) the port-channel 1 interface
B) the highest number member interface
C) all member interfaces
D) the lowest number member interface
Answer is A
one new question on SNMP:
Q1. What is SNMPv2 authentication procol.
A. Community Strings
B. HMAC-MD5
C. HDMAC-SHA
Lab
eigrp 2, acl sim 1, acl simlet 2 mod 3
Labs:EIGRP 222, ACL1, ACL2.
Look at new questions in Konrad dump(there was an etherchannel question in my exam)
Passed today got 917/1000. Simulation ACL1,ACL2 mod(4),EIGRP with AS no.221. Got 51 questions. Thank you all for your comments study 9tut,watson and examtut.
dump valid
there is a new ques and i don't know correct ans:
what is the parameter do not need match in a ether channel?
a- duplex
b- trunk encapsulation
c- negotiation trunk status
d- speed
i 'm not good at english :D sorry sory .. :))
I'm giving the exam this Tuesday and I can't open this file with bluestacks a+. How do you open this file? Please advise asap!
an some one send me 200-125 exam dumps in pdf
mail; [email protected]
Email to: [email protected]
thanks to 9tut.com and Watson