Log into your Prepaway Account
Please Log In to download ETE file or view Training Course
Registration is free and easy - just provide your E-mail address.
Click Here to Register
Exam: | 200-105 - ICND Interconnecting Cisco Networking Devices Part 2 |
Size: | 6.3 MB |
Posted: | Monday, September 11, 2017 |
Download:
|
Cisco.Actualtests.200-105.v2017-09-11.by.paisley.120q.ete |
Download Free 200-105 Exam Questions |
Log in to make your opinion count.
Registration is free and easy - just provide your E-mail address.
Click Here to Register
Use Discount Code:
A confirmation link was sent to your e-mail.
Please check your mailbox for a message from [email protected] and follow the directions.
Passed today 907/1000!
Points to pass: 825
Questions: 47
Simulations: OSPF Hotspot Q93 & Frame Relay Q86
this problem was fixed
Questions 47
Lab: OSPF Hotspot and frame relay.
100% valid. All questions I had came from this ETE.
An big hug from london.
Took it today and scored above 900.
Every question I had was on this collection.
Good luck
No simulation(ospf,Nat)
I have only 47 total questions with all the the simulation in dump. I'm Glad my score is legit now and i am CCNA.
Resources:
200-125 Cisco Press - Well Odom
Packet Tracer
Read carefully and practice!
Questions 47
Lab: OSPF Hotspot and frame relay.
To be honest, i forgot them. But one for sure was 1 Question with 4 sub Questions where they give you tapology to check router settings.
If you know study the dump. You should pass
"
A+ player doesn't open ETE files correctly. A+ Player tends to provide users with irrelevant files from its own repository when it's unable to open the user's ETE file. Therefore, the file you view in A+ Player might not be the file you think you have opened. Use ETE Exam Simulator or ETEViewer to play ETE files properly."
ETEViewer only allows file sizes up to 5MB. Unfortunately most of the revelant ete files to this thread are larger than the 5MB cap. Worth mentioning...
can someone tell me which lap come to exam
thinks
When I did ICND1 it said the same thing about validatin, I was worried because I didn't run commands to get answers, but it went through 1000/1000 on ICND1. You should be fine and congrats. Btw what lab did you get on your ICND2?
answer for simlet question is *enable was right
read carefully and do router configure carefully....
I saw in comments that the possible sims are either Frame Relay, OSPF or EIGRP.
In dump I only saw a no config Frame Relay sim which had like 4 questions, one OSPF sim with the protocol activated on the wrong subnet and a NAT sim that requires the configuration of the NAT pool and ACL.
Are these the sims you had in your exams?
Also, what is required in the EIGRP sim?
Ty!
Questions 47
Lab: OSPF Hotspot and frame relay.
I'm from india but now i'm here at Brazil and i wanna do this test
thanks!
Cheers.
Next Step CCNP.
This ETE is all you need. Literally studied nothing else. Passed with a 973/1000.
Nada is enough to pass, took me 20 minutes to finish the test.
Good luck everyone! hurry up, at september cisco change the tests!
I had the OSPF and Frame Relay sim, but pretty much the exact scenario was shown in dump (provided you know the basic show commands that others have mentioned).
Thanks to everyone who commented with a score recently - it really helped my confidence with this.
[email protected]
I have a feeling Cisco will be updating their questions soon as the dump has been uploaded for a while. Good Luck to everyone that is looking to be certified
Hello
Can someone kindly send me the updated questions pdf, please?
I am about to take my exam soon
thanks in advance
Hi guys just passed icnd2 right now 011-10-2017 united state Texas the Nada dump still valid like 98%
i studied Nada dump and Debra
but i focus on Nada dump coz most the questions same
Now For CCNP CLASS
Good Luck Guys
Also used Debra, Kate and Larry to study.
No configuration questions, just the Frame-relay (Dubai) and OSPF hotspot (with slight differences).
Good Luck!
Just passed today.. all questions and answers were there.
I had frame relay sim.. 3 drag and drop from this ete.
Bear in mind that you must know the concepts.
Good luck all
Big hug from london.
A. I want to make it clear to everyone, DO NOT JUST USE THE DUMPS.Study the material for real world, or you will regret it.
B. I studied the material for the ICND2/CCNA on my own for 1 year (eBooks, 9TUT, videos, Packet Tracer, Bought my own routers/switches, etc).
C. Majority of questions and answers from Nada dump. Lots of switching questions (20-25 out of the 47).
D. Sims were OSPF1, OSPF2, and Frame Relay from 9TUT. IP's were different in each scenario.
E. Make sure you study practice questions from all the .ETE listed below. You can find all of them with an easy google search.
1.Nada ETE
2.Debra ETE
3.Examtut ETE
4.Watson ETE
5.Testking 999Q ETE
The testking ETE gives you a lot of off base questions not in the other ETE's. I studied that just in case any weird or random questions came up.
F. ***Important*** Make sure you find and download "101 CCNA Labs with solutions" and "101 CCNP Labs with solutions" file on the internet. Again, a simple google or duckduckgo search can locate this. These practice labs are absolutely essential.
F-2. ***Important*** If you CANNOT perform any of these practice labs in the set time they provide before you take the exam, then don't even bother.
I will appreciate it kindly.
My email is [email protected]
Thanks in advance
Thanks for the help
Like from J, United Kingdom's comment, as he said it...exactly!!!
Thanks in advance.
One lab was new.
Interested in seeing if it is similar to dump
Thanks
Can someone kindly send me the updated questions pdf, please?
I will be taking the exam at the end of the month. Thanks in advance
[email protected]
thank you
In my case 100% valid, no new questions.
After question 44 I failed all of them on purpose not to be suspicious.
Score: 920.
The only sim i had was the frame relay one.
I studied NADA, DEBRA and of course, 9tut
could I have the ICND2 pdf please?I can't open .ete file.My e-mail address is [email protected]
Many thanks in advance
Know those 5 commands and you will find the answer.
show ip eigrp topology
show ip route
show ip protocols
show running-config
show frame-relay map
Used: Nada, RonBoot, Debra and Sims from 9tut.
Debra was the most efficient.
SIMS: OSPF, EIGRP, Frame Relay.
Had 3-4 new questions, but if you know your stuff, it will be extremely easy.
Finally, CCNA certified.
Thanks!
I have a question.. Enter question in the exam of the drag and drop?? For example, question 82, 83, 84, 85
Thanks!!
Dump 100% valid.
CCNA GOT IT DONE :P
How will router2 be affected by the configuration of R1 that is shown in the exhibit
I cannot understand the explanation and the correct answer.(A)
The process ID is local to the router, and two OSPF neighboring routers can have different OSPF process IDs
Unlike EIGRP for example, the process id does not have to match between 2 neighbors for a neigborship to establish.
You can run multiple OSPF processes on the same physical router and the process id would be how the router distinguishes between the processes. Also when redistributing OSPF into another routing protocol you need to specify the process id.
Both routers are in Area 0
Referred Nada, Debtra and 9Tut
2 new questions
had 2 non config sim (ospf+frame-relay)
[email protected]
Can someone please forward me the dumos in PDF via email.
Thanks in advance
plz let me know
Thanks !
Thx
passed today with 986 Dump is still valid but you have study both dumps Debra and NADA.
Thank You
OSPF in the DUMP,
Frame-Relay in the dump
and EIGRP just know you show commands on these and you will be sorted.
the rest of the questions were on the dump there was only one question that was not in there which wanted to select possiible answers for the difference between OSPFv2 and OSPFv3 Good Luck guys
Dumps were accurate about 85-90%
any one took the exam recently
I am waiting u guys to answer
make sure to practice sim labs from 9tut. download the sims and practice the commands..
Dump still valid in Argentina.
Using Debra, Nada and RonBoot.
Some different labs, but very easy to solve.
TIA
But if you know show commands you should be fine.
whic is the righ link to 9tut's questions? I found "explanations" but no "questions".
Thanks
Good luck :)
Good luck all ....
What are the 3 factors a network administrator must consider before implementing Netflow in the network.
Debra says port availabilty.
9tut says the number of devices exporting netflow data
Both choose
cpu utilzation and
where Netflow data will be sent.
Who is correct.
Finally CCNA certified.
This dump is valid 90%
3 Sims(EIGRP,Frame Relay & OSPF)
some new questions also. So be prepared.
Best of Luck !
Excellent work cisconerd.
How about this as an explanation :
Static routes are configured with lower administrative distances than OSPF routes
meaning that static routes override OSPF routes, provided they pertain to the same destination prefix.
Because static routes and directly connected routes admin distance is less than ospf, static routes and directly connected routes will only populate the routing table of R1
53 Questions
All Questions from dump and Ophelia dump
Only New scenario contain 4 Questions
Cheers
3 simulations ( eigrp- frameRelay- ospf)
All multipleChoise no configration
Olso There are some new questions i found in carolina dump
Can some one provide full link to Nada, RonBoot, Debra and Sims dumps please.
OSPF,EIGRP AND FRAME-RELAY SIM! check on 9tut ICND 2.! GOOD LUCK
SIMS that came in are OSPF, EIGRP and Frame Relay.
A lot of drag&drop questions.
Dump 95% valid!
Please STOP asking for PDF to your email! this is not a charity. If you need the test buy it like everyone else. What is the point of posting your email and begging?? you are ruining the forum by asking the same thing. This page is supposed to be used to discuss the questions and answers or updates/alternation not people rudely asking for piracy.
Best of luck.
I have my exam on 9/29/2017..
Thanks in advance!!
Passed easily today. Had Frame Relay, EIGRP, and OSPF.
-USA
passed yesterday with 881 no configs only show run commands found the 6 routers EIRGP sim and the Dubai frame relay thanks you now I'm CCNA certified....
BEST OF LUCK....
Thanks..
are these dumps still valid in uk?
please tell me.. IS THIS DUMP STILL VALID?
Huge thanks to www.prepaway.com and your contributors. I passed both ICND1 and ICND2 thanks to Todd Lammle's CCNA Study Guide and your awesome dumps. Great job, keep it up. You guys change lives!
Did one one write ICND2 exam for this week?
(9/29/2017-9/29/2017)?
If so, can someone confirm if the dump questions are still valid?
Also used the CBT nugget videos & 9tut.
But dumps are still valid. One had new one question. But learn the show commands esp for frame frlay!
I got:-
- 50 questions
- and, 3 Sims
a. EIGRP Troubleshooting Sim
b. Frame Relay Sim
c. OSPF
prepaway.com/200-105.html
Exactly same questions with jumbled answers. EIGRP, Frame – relay and OSPF SIM with different questions. Know your show commands well and basic concepts of EIGRP and OSPF. No IPv6 questions at all. Masha Allah , I’m CCNA Certified now. CCNP next, Insha Allah.
Enjoy ;)
I'm going to take the ICND2 exam next week and i wanted to ask:
is there a lot of questions about frame relay in this exam?? its very old technology...
thanks
Your gonna get grilled hard on Frame Relay so understand how DLCI's work
EIGRP your gonna have to know the concept behind EIGRP and how routers manage to establish neighbor relations.
I got no questions that required configuring, so that kinda ticked me off as i spent over 50+ practicing on live equipment.
I will be taking this exam in couple of weeks time, are the dumps still valid?
Thanks,
Can someone Confirm?
Guys, can you share your experience in the last 200-105 exam?
**Congrats people who passed last days!!!
Only 5-6 questions different.
I Got the EIGRP question.
1) K values were NOT mismatched in mine. the AS was mismatched: eigrp 111 vs eigrp 1
2) The loopback interfaces were also in a shutdown state, the problem was NOT that they were not being advertised.
3) Load balancing question was present
Passed today in Saudi Arabia with 1000/1000
Just you need to do labs
This ETE is valid, Almost all there.
Thanks a lot for prepaway.com,9tut.net,testking.com & orbitco-ccna-pastquestions.com for the new questions.
On 9tut i wrote more detail about the questions on this exam
http://www.9tut.net/icnd2-200-105/share-your-new-icnd2-experience
score 854...
Could please someone confirm?
Don't relay on dumps only,but throughly study EIGRP protocol and concept (Todd Lammle's book),otherwise,you are probably about to fail exam.Good luck fellas !
I'm implement packet tracer to verify it. The correct is B.
@Ciscoita: yep, B is correct.
You can verity by Packet tracer. Good luck to all :)
Thanks Prepaway, Nada and 9TUT
three sims, eigrp,osfp fram relay, same on the exam, but sometime, they change question, you have to read the question goed and anderstan. for example, the netframe quesion, they change the dlci numbers, and which connetion uses the default encapsulation, for serial int. the anwar on my quesion was deesouth.so becarefu.
PS The default route is seen in the routing table of R2. The correct setup should be that the default route should be pointing out of S1/0 not S0/0 which causes the loop. This question isn't concerned about the routing loop so taking all criteria into account answer B is the only correct option.
thanks for your support
dump still valid
and 9tut for lab
https://www.testking.com/200-125.htm
and on EIGRP qusetion about summrization,
the lab ( no configuration required )
OSPF from dump + EIGRP from 9tut + Frame-relay
53 Questions.
it has the biggest amout of question among the exams.
but most important it has good explanations of the answers and some question even have a link to webpage that explains the tpic.
ty very much for that exam
This dump is still valid.
I learned from dump and 9tut.com
Did you only study from dump? Did you get any new questions that was not in dump?
- 53q, passing score: 825.
- SIM: EIGRP Troubleshooting (9tut.net), Frame Relay (q86 dump), OSPF (q90 dump).
- Other questions: dump + https://www.testking.com/200-125.htm
- q39 (dump) the correct is B: full table + default route.
dump is valid only few new questions, thanks for everyone.
- q39 correct answer is A: no neighbor relationship will formed because R2 is in Area 0 and R1 is configured with Area 1.
Maybe you had a different "modified" version of the question on your exam.
Aboodnet
default violation mode is shutdown which will generate an SNMP message as will restrict, only protected (not default) will not generate this message
if there is no port-security violation line assume it is in shutdown
Thanks ronbot and nada. (Ronbot q on nada)
Study all nada and 29q in the link. Eigrp
R1 and R2 are on the picture both in OSPF Area0, no indication R2 is not.
but still the awnser is: not neighboring.
and why is this link in the explanation between ''router OSPF1 and area 0, the OSPF proces das not mather to the area, you can have multiple processes running in an area or even on 1 router.
can anyone tell me the logic behind this?
All brain-dump are valid: 9tut+NADA-02.10
go through them all, not hard, you will pass for sure!!!!
important: eigrp+auto summarization (must know well on these subjects) if you want score 1000/1000.
thank you again, NADA-02.10!!!
on my way to CCNP now! long way to go, lol!
https://www.vumingo.com/exam-testing-engine.html
Correct answer for this question is neighbours will form and R2 will receive routing updates from R1. However, when R2 references a route not in its routing table a loop will occur as it will send the packet back to itself. I have labed it up in GNS3 I recommend the same for you. Best to see it first hand.
Router processor is only locally significant but area numbers must match.
Thanks
Valid dump
New EIGRP Lab Question- Read about passive interfaces, Some new questions on network monitoring, get familiar with network monitoring commands. The choice order can be changes, IP Addresses can be changed and some answers might be difference in few cases.
Good luck all.
any news on my previous post please?
How accurate was dump with your exam?
Thanks
Passed: scored 9XX/1000.
Studied using dump exclusively.
Regards
CiscoKid
EIGRP's AS on the other hand does need to be the same.
This dump is 95% valid. Pay attention to big EIGRP lab (6 x router, 2 x switch). Questions can differ. My friend had another portion of questions. Good preparation for this exam = 9tut.com, NADA.120q , and CCNA questions for completeness LUSI.272q or GILLBEAST.299q = success. However to be great IT guy you must go through Official Cert Guide Cisco CCNA Routing and Switching ICND2 200-105.
Thanks to NADA!!!
Explanation: For the command [router ospf 1], 1 is the process ID, not the ospf area. Process ID is locally significant, but has no bearing on the area of the network statements that follow. All three network interfaces are participating in area 0, along with all of R2's interfaces.
This configuration will allow for a neighbor relationship between R1 & R2 to form, but it results in a routing loop in area 0. R2 will see the default route of 0.0.0.0 via R1, but R1 shoves the packets right back out to R2.
Note that this is not the only ete with an incorrect answer for this question.
Source: CCNP with real equipment.
Cheers,
Will
960
The eigrp sim and the Dubi sim showed up, non-config. Dubi sim numbers were different so know why the answers were the answers. multiple choice are 100% from the NADA ete but orders were different. got 1 drag and drop (DTE, PVC, DLCI, LMI) EIGRP sim with the only new items. know all your show cmd, don't sweat it. even if miss all 4 EIGRP sim question, you'll pass.
Don't relay on dumps only,but throughly study EIGRP protocol and concept (Todd Lammle's book),otherwise,you are probably about to fail exam.Good luck fellas !
There are some Netflow and GLBP questions which are on examtut.
This DUMP will grantee pass. Thanks NADA.
Got 986 out of 1000. Go for it guys!!!!!!
I learned from dump and 9tut.com The dump valid.
I had 5-7 new question which is not in it.
In the exam there was no LAB task, only 3 topology task (2 in the dump)
The question q39 is the question about the ospf area 0 scenario about how will router R2 be affected by the configuration of R1 : and the answer is not the A in the dump but is B that obtain a full routing table, including a default route from R1 ?? :) thanks
Passed yesterday with 986
interface fastethernet0/4
switchport mode access
switchport port-security
switchport port-security mac-address 0000.1111.1111 switchport port-security maximum 2
switchport port-security
What is the result of the above configuration?
It states the switch can send a SNMP message to the network management station but wouldn't switchport port-security violation restrict have to be set for that answer to be correct?
Your answer is: No password is required its wrong !!