Test Prep ASVAB Test Practice Test 51
Question 500
What is a reamer generally used for?
- Weld two pieces of sheet steel
- Tighten wire terminals
- Finish a predrilled hole to accurate size and surface
- Clean paint from wood
Explanation
Correct Answer
C:Best answer. Reaming removes a small allowance after drilling.
Incorrect Answers
A:Not best. Weld two pieces of sheet steel: Welding joins metal.
B:Not best. Tighten wire terminals: Crimpers make connections.
D:Not best. Clean paint from wood: Sandpaper removes coatings.
Question 501
What is the purpose of a drill press vise?
- Measure drill RPM
- Increase electric motor voltage
- Hold the workpiece securely against rotation
- Replace eye protection
Explanation
Correct Answer
C:Best answer. Clamping prevents the part being spun by the drill.
Incorrect Answers
A:Not best. Measure drill RPM: A tachometer measures speed.
B:Not best. Increase electric motor voltage: A vise does not alter electrical supply.
D:Not best. Replace eye protection: A clamp cannot prevent chips from reaching eyes.
Question 502
Why should a rotating machine's chips be removed with a brush after stopping?
- Increase spindle torque
- Sharpen the bit in place
- Make the metal nonconductive
- Avoid hand contact with sharp moving material
Explanation
Correct Answer
D:Best answer. A brush and stopped spindle reduce injury risk.
Incorrect Answers
A:Not best. Increase spindle torque: Chip cleaning does not add torque.
B:Not best. Sharpen the bit in place: Chip removal is not sharpening.
C:Not best. Make the metal nonconductive: Brushing does not change conductivity.
Question 503
What does a bench vise primarily do?
- Create gas pressure
- Mix paint at a calibrated rate
- Measure electric current
- Grip a workpiece for bench operations
Explanation
Correct Answer
D:Best answer. A vise holds material while filing or fitting.
Incorrect Answers
A:Not best. Create gas pressure: Compressors produce pressurized gas.
B:Not best. Mix paint at a calibrated rate: Mixers do that.
C:Not best. Measure electric current: An ammeter measures current.
Question 504
Which saw is typically selected for cutting metal stock by hand?
- Coping saw with coarse wood blade only
- Hacksaw
- Crosscut wood saw
- Hand plane
Explanation
Correct Answer
B:Best answer. A fine-tooth hacksaw blade cuts many metals.
Incorrect Answers
A:Not best. Coping saw with coarse wood blade only: A coping saw is chiefly a fine woodworking tool.
C:Not best. Crosscut wood saw: Its tooth geometry suits lumber.
D:Not best. Hand plane: A plane smooths wood surfaces. It does not meet the specific requirement in the question.
Question 505
For crosscutting wood, which saw teeth are arranged for cutting across the grain?
- Hacksaw
- Rip saw
- Crosscut saw
- Masonry saw
Explanation
Correct Answer
C:Best answer. Crosscut teeth sever wood fibers across grain.
Incorrect Answers
A:Not best. Hacksaw: A hacksaw is chiefly for metal. It does not meet the specific requirement in the question.
B:Not best. Rip saw: Rip teeth primarily cut parallel to grain.
D:Not best. Masonry saw: Masonry tooling cuts concrete or brick.
Question 506
What is the difference between a rip cut and a crosscut in lumber?
- Rip always follows a circle
- Both always use identical blade tooth geometry
- Crosscut only cuts metal
- Rip follows the grain; crosscut crosses it
Explanation
Correct Answer
D:Best answer. Wood grain direction determines these cutting terms.
Incorrect Answers
A:Not best. Rip always follows a circle: Rip is not defined by curvature.
B:Not best. Both always use identical blade tooth geometry: Tooth designs can differ.
C:Not best. Crosscut only cuts metal: Crosscut describes wood-grain orientation.
Question 507
What does a wood chisel do?
- Remove or shape wood by cutting fibers
- Measure ambient temperature
- Detect hidden electric wiring automatically
- Apply precise torque to bolts
Explanation
Correct Answer
A:Best answer. A sharp chisel pares or chops wood. This is the concept directly requested by the question.
Incorrect Answers
B:Not best. Measure ambient temperature: Thermometers do that.
C:Not best. Detect hidden electric wiring automatically: A chisel is not a detector.
D:Not best. Apply precise torque to bolts: Torque tools do that.
Question 508
What is a hand plane mainly used for?
- Generate arc welding current
- Cut internal steel threads
- Measure pipe pressure
- Smooth and dimension wood surfaces
Explanation
Correct Answer
D:Best answer. The blade shaves thin layers of wood. This is the concept directly requested by the question.
Incorrect Answers
A:Not best. Generate arc welding current: A plane is manual woodworking equipment.
B:Not best. Cut internal steel threads: A tap cuts metal threads.
C:Not best. Measure pipe pressure: Pressure gauges do that.
Question 509
What is sandpaper grit number generally associated with?
- Wood moisture percentage directly
- Torque applied to a bolt
- Electrical supply frequency
- Abrasive particle size
Explanation
Correct Answer
D:Best answer. Higher common grit numbers indicate finer particles.
Incorrect Answers
A:Not best. Wood moisture percentage directly: Moisture meters measure that.
B:Not best. Torque applied to a bolt: Torque uses N-m or ft-lb.
C:Not best. Electrical supply frequency: Frequency uses hertz.
Question 510
Which woodworking joint commonly uses an inserted projecting tongue and a matching cavity?
- Mortise-and-tenon joint
- Butt joint only
- Compression fitting
- Lap weld
Explanation
Correct Answer
A:Best answer. A tenon fits into a mortise. This is the concept directly requested by the question.
Incorrect Answers
B:Not best. Butt joint only: A basic butt joint joins edges without the mortise.
C:Not best. Compression fitting: Fittings seal tubing. It does not meet the specific requirement in the question.
D:Not best. Lap weld: Welding joins metals. It does not meet the specific requirement in the question.