Test Prep ASVAB Test Practice Test 52
Question 510
Which woodworking joint commonly uses an inserted projecting tongue and a matching cavity?
- Mortise-and-tenon joint
- Butt joint only
- Compression fitting
- Lap weld
Explanation
Correct Answer
A:Best answer. A tenon fits into a mortise. This is the concept directly requested by the question.
Incorrect Answers
B:Not best. Butt joint only: A basic butt joint joins edges without the mortise.
C:Not best. Compression fitting: Fittings seal tubing. It does not meet the specific requirement in the question.
D:Not best. Lap weld: Welding joins metals. It does not meet the specific requirement in the question.
Question 511
What is the intended function of a wood clamp during glue-up?
- Hold parts in alignment while adhesive cures
- Increase wood grain length
- Remove all sawdust from the shop
- Automatically dissolve glue
Explanation
Correct Answer
A:Best answer. Clamping maintains contact and geometry. This is the concept directly requested by the question.
Incorrect Answers
B:Not best. Increase wood grain length: Clamps do not alter fiber length.
C:Not best. Remove all sawdust from the shop: Dust collection is separate.
D:Not best. Automatically dissolve glue: Adhesive must still cure.
Question 512
Why is a pilot hole sometimes drilled before driving a wood screw?
- Increase screw diameter
- Eliminate the need for matching fasteners
- Turn softwood into hardwood
- Reduce splitting and guide the screw
Explanation
Correct Answer
D:Best answer. A pilot hole lowers wedging forces and helps alignment.
Incorrect Answers
A:Not best. Increase screw diameter: The screw remains the same size.
B:Not best. Eliminate the need for matching fasteners: Fastener selection remains important.
C:Not best. Turn softwood into hardwood: Drilling does not change wood type.
Question 513
What does a spirit level check?
- Material hardness
- Electrical current flow
- Horizontal or vertical orientation relative to gravity
- Engine horsepower
Explanation
Correct Answer
C:Best answer. The bubble centers when the instrument is level or plumb.
Incorrect Answers
A:Not best. Material hardness: Hardness tests use indentation methods.
B:Not best. Electrical current flow: Current meters are electrical.
D:Not best. Engine horsepower: A level is not a dynamometer.
Question 514
What is a plumb bob used for?
- Establish a vertical reference line
- Cut circular holes
- Verify wire insulation
- Measure fuel flow
Explanation
Correct Answer
A:Best answer. Gravity aligns a suspended weight vertically.
Incorrect Answers
B:Not best. Cut circular holes: Hole saws cut holes. It does not meet the specific requirement in the question.
C:Not best. Verify wire insulation: Electrical testers assess insulation.
D:Not best. Measure fuel flow: Flowmeters measure flow. It does not meet the specific requirement in the question.
Question 515
What is a framing square used to check or mark?
- Electrical capacitance
- Heat-treat temperature
- Oil viscosity
- Right angles in layout work
Explanation
Correct Answer
D:Best answer. A framing square helps establish perpendicular edges.
Incorrect Answers
A:Not best. Electrical capacitance: A capacitance meter measures farads.
B:Not best. Heat-treat temperature: A pyrometer measures temperature.
C:Not best. Oil viscosity: Viscosity tests measure fluid flow resistance.
Question 516
What is the main benefit of a dial indicator in machining?
- Detect small displacement or runout
- Measure arc-flash energy directly
- Drive nails quickly
- Cut a continuous thread
Explanation
Correct Answer
A:Best answer. A dial indicator shows tiny positional changes.
Incorrect Answers
B:Not best. Measure arc-flash energy directly: Arc energy assessment requires other data.
C:Not best. Drive nails quickly: Hammers and nailers do that.
D:Not best. Cut a continuous thread: Taps and dies cut threads.
Question 517
Why is material marked with a scribe before precise cutting?
- Anneal the metal
- Provide a fine layout line
- Increase tensile strength immediately
- Remove all tool burrs
Explanation
Correct Answer
B:Best answer. A scribe creates a narrow visible mark on a surface.
Incorrect Answers
A:Not best. Anneal the metal: Annealing requires controlled heating.
C:Not best. Increase tensile strength immediately: Scribing does not strengthen metal.
D:Not best. Remove all tool burrs: A scribe marks rather than deburrs.
Question 518
What is the purpose of a deburring tool?
- Change thread pitch
- Measure torque
- Create a center hole for drilling
- Remove sharp raised edges after machining
Explanation
Correct Answer
D:Best answer. Deburring improves fit and handling safety.
Incorrect Answers
A:Not best. Change thread pitch: Deburring does not rethread a part.
B:Not best. Measure torque: A torque wrench measures torque.
C:Not best. Create a center hole for drilling: A center drill starts holes.
Question 519
What does a wire brush commonly remove from metal?
- All metal fatigue permanently
- Loose rust, scale, or debris
- Deep internal cracks reliably
- Electrical current from a powered circuit
Explanation
Correct Answer
B:Best answer. Bristles scrape unwanted surface material.
Incorrect Answers
A:Not best. All metal fatigue permanently: Fatigue damage requires engineering assessment.
C:Not best. Deep internal cracks reliably: Visual brushing cannot detect all subsurface defects.
D:Not best. Electrical current from a powered circuit: Brushing does not make energized wiring safe.
Question 520
Which tool is normally used to tighten a hexagonal nut without damaging its flats?
- Correct-size box-end wrench
- Pliers with serrated jaws in all cases
- Center punch
- Flat file
Explanation
Correct Answer
A:Best answer. A fitted box end grips the nut flats securely.
Incorrect Answers
B:Not best. Pliers with serrated jaws in all cases: Pliers may round fastener heads.
C:Not best. Center punch: A punch marks positions. It does not meet the specific requirement in the question.
D:Not best. Flat file: A file removes material rather than tightens.