Test Prep ASVAB Test Practice Test 38
Question 370
How does an LED produce visible light?
- Electron-hole recombination in a semiconductor
- Magnetizing iron until luminous
- Heating a filament until incandescent
- Vibrating air with a cone
Explanation
Correct Answer
A:Best answer. An energized junction emits photons. This is the concept directly requested by the question.
Incorrect Answers
B:Not best. Magnetizing iron until luminous: Magnetism alone does not make a visible LED beam.
C:Not best. Heating a filament until incandescent: That describes an incandescent lamp.
D:Not best. Vibrating air with a cone: That describes a loudspeaker.
Question 371
What does a thermistor primarily respond to?
- Atmospheric pressure only
- Light only
- Temperature
- Mechanical vibration only
Explanation
Correct Answer
C:Best answer. Thermistors have resistance that varies with temperature.
Incorrect Answers
A:Not best. Atmospheric pressure only: Barometric sensors measure pressure.
B:Not best. Light only: Photoresistors respond to illumination.
D:Not best. Mechanical vibration only: Accelerometers detect motion.
Question 372
Which device is used to view voltage as a function of time?
- Oscilloscope
- Torque wrench
- Speedometer
- Ohmmeter only
Explanation
Correct Answer
A:Best answer. An oscilloscope displays waveform voltage versus time.
Incorrect Answers
B:Not best. Torque wrench: A torque wrench measures applied twisting torque.
C:Not best. Speedometer: A speedometer indicates speed. It does not meet the specific requirement in the question.
D:Not best. Ohmmeter only: An ohmmeter measures resistance.
Question 373
What should be done before measuring resistance with a typical ohmmeter?
- Short the mains with leads
- Remove power and discharge stored energy safely
- Attach the meter only across energized high voltage
- Increase supply to maximum voltage
Explanation
Correct Answer
B:Best answer. Resistance measurement normally uses meter-supplied test current and requires a de-energized circuit.
Incorrect Answers
A:Not best. Short the mains with leads: That creates a fault.
C:Not best. Attach the meter only across energized high voltage: An ohmmeter is not used that way.
D:Not best. Increase supply to maximum voltage: That may damage the meter and present hazards.
Question 374
In binary logic, what does an AND gate output when both inputs are 1?
- An analog sine wave
- 0
- 1
- An undefined alternating voltage always
Explanation
Correct Answer
C:Best answer. AND is high only when all inputs are high.
Incorrect Answers
A:Not best. An analog sine wave: Digital AND produces logic levels.
B:Not best. 0: Zero is the output if at least one input is zero.
D:Not best. An undefined alternating voltage always: Defined valid digital inputs yield a defined output.
Question 375
When one input of a two-input OR gate is 1, what is its output?
- An audio tone necessarily
- 0
- A negative resistance
- 1
Explanation
Correct Answer
D:Best answer. OR outputs high if at least one input is high.
Incorrect Answers
A:Not best. An audio tone necessarily: A logic output is a level, not necessarily audio.
B:Not best. 0: Both inputs must be zero for OR to be low.
C:Not best. A negative resistance: Logic gates do not output resistance.
Question 376
What is the purpose of an insulating jacket around a wire?
- Make current flow without a circuit
- Raise copper's atomic number
- Create a permanent magnet
- Prevent unintended contact and current paths
Explanation
Correct Answer
D:Best answer. Insulation restricts conduction and protects users.
Incorrect Answers
A:Not best. Make current flow without a circuit: A circuit still needs a path.
B:Not best. Raise copper's atomic number: Insulation does not change elements.
C:Not best. Create a permanent magnet: Plastic insulation is not magnetization.
Question 377
What is a common symptom of a short circuit across a low-voltage supply?
- Very high current until protection intervenes
- Supply voltage is always doubled
- Every lamp becomes a capacitor
- All conductors become superconductors
Explanation
Correct Answer
A:Best answer. A low-resistance unintended path can draw excessive current.
Incorrect Answers
B:Not best. Supply voltage is always doubled: A short tends to collapse voltage at the fault.
C:Not best. Every lamp becomes a capacitor: A short cannot change components into capacitors.
D:Not best. All conductors become superconductors: A short is not superconductivity.
Question 378
Which part of a basic DC motor interacts with a magnetic field to produce torque?
- A fuse holder
- Only a cooling fan
- A rubber casing
- Current-carrying winding
Explanation
Correct Answer
D:Best answer. Magnetic force on conductor currents produces motor torque.
Incorrect Answers
A:Not best. A fuse holder: A fuse holder does not generate torque.
B:Not best. Only a cooling fan: A fan removes heat, not electromagnetic torque.
C:Not best. A rubber casing: A casing is not the electromagnetically active element.
Question 379
What electrical component converts an analog input into a digital number?
- Relay only
- Heating resistor alone
- Rectifier diode alone
- Analog-to-digital converter
Explanation
Correct Answer
D:Best answer. An ADC samples and quantizes an analog signal.
Incorrect Answers
A:Not best. Relay only: A relay switches contacts. It does not meet the specific requirement in the question.
B:Not best. Heating resistor alone: A resistor cannot encode a digital measurement by itself.
C:Not best. Rectifier diode alone: A diode is not a digital converter.
Question 380
A capacitor in a DC circuit has fully charged and an ideal steady state is reached. What happens to current through it?
- It generates alternating current spontaneously
- It increases without limit
- It approaches zero
- It becomes an ideal short forever
Explanation
Correct Answer
C:Best answer. An ideal charged capacitor blocks steady DC current.
Incorrect Answers
A:Not best. It generates alternating current spontaneously: A passive capacitor does not oscillate by itself.
B:Not best. It increases without limit: Steady capacitor conduction does not diverge.
D:Not best. It becomes an ideal short forever: An ideal capacitor is open to steady DC after charging.