Juniper JN0-664 Practice Test 7
Question 60
A Junos routing design reviewer evaluates an unsafe shortcut in this network customer scenario. Two Junos routers share an IPv4 OSPF area but an incorrectly applied OSPFv3 interface configuration prevents the IPv6 neighbor from forming. Which assumption is MOST DIRECTLY dangerous or unsupported? Select ONE best answer.
- Set an arbitrary unused BGP community and promise every transit operator will lower its preference without agreeing a corresponding community policy.
- Conclude that working OSPFv2 routes automatically provide IPv6 reachability on Junos without any OSPFv3 or other IPv6 routing configuration.
- Install a summary for discontiguous customer access blocks and drop all component routes without verifying that the ABR actually forwards the entire aggregate.
- Configure one router in a shared area as NSSA while leaving its peer as a normal stub area and expect their adjacency and external imports to work.
Explanation
Correct Answer
B:That conflicts with the edge-to-cloud principle: OSPFv3 uses IPv6-related control-plane processing and link-local neighbor communication; it must be configured and verified according to the selected address family and release.
Incorrect Answers
A:This alternative proposes: Set an arbitrary unused BGP community and promise every transit operator will lower its preference without agreeing a corresponding community policy. It concerns a different Junos engineering issue BGP communities and selective transit routing policy, not the directly tested provider-network issue OSPFv3 IPv6 neighbor and IPv4 separation.
C:This alternative proposes: Install a summary for discontiguous customer access blocks and drop all component routes without verifying that the ABR actually forwards the entire aggregate. It concerns a different Junos engineering issue OSPF interarea route summarization and route restrictions, not the directly tested provider-network issue OSPFv3 IPv6 neighbor and IPv4 separation.
D:This alternative proposes: Configure one router in a shared area as NSSA while leaving its peer as a normal stub area and expect their adjacency and external imports to work. It concerns a different Junos engineering issue OSPF stub NSSA and external LSA handling, not the directly tested provider-network issue OSPFv3 IPv6 neighbor and IPv4 separation.
Question 61
A Junos service-provider routing engineer investigates the following routing and service incident: An ISP aggregates several access loopback prefixes between areas, but one unassigned address range in the summary attracts traffic with no valid downstream path. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.
- Apply summarization or import/export controls at the appropriate OSPF area boundary after proving which access prefixes should be reachable.
- Trace an LDP Layer 2 circuit end to end using neighbor signaling, pseudowire identifiers and operational connection state before changing customer VLANs.
- Investigate an OSPF adjacency that remains in ExStart or Exchange by comparing interface MTU and protocol parameters before resetting every neighbor.
- Choose the correct OSPF stub or NSSA area design according to the requirement for redistributed external routes and verify supported Type 7 translation.
Explanation
Correct Answer
A:ABRs can advertise summary information between areas while routing policy and area ranges alter which routes are visible; overly broad aggregation can blackhole traffic if specifics lack coverage. Inspect specific prefixes at the ABR, area range configuration, policy match criteria, summary LSA presence and forwarding toward the aggregated destinations.
Incorrect Answers
B:This alternative proposes: Trace an LDP Layer 2 circuit end to end using neighbor signaling, pseudowire identifiers and operational connection state before changing customer VLANs. It concerns a different Junos engineering issue LDP signaled Layer 2 circuit pseudowire status and VC identifiers, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
C:This alternative proposes: Investigate an OSPF adjacency that remains in ExStart or Exchange by comparing interface MTU and protocol parameters before resetting every neighbor. It concerns a different Junos engineering issue OSPF adjacency MTU and hello compatibility diagnosis, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
D:This alternative proposes: Choose the correct OSPF stub or NSSA area design according to the requirement for redistributed external routes and verify supported Type 7 translation. It concerns a different Junos engineering issue OSPF stub NSSA and external LSA handling, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
Question 62
A provider routing design review considers this situation. An ISP aggregates several access loopback prefixes between areas, but one unassigned address range in the summary attracts traffic with no valid downstream path. A colleague proposes: Apply summarization or import/export controls at the appropriate OSPF area boundary after proving which access prefixes should be reachable. Which technical principle BEST supports that action? Select ONE best answer.
- On an OSPF broadcast network a DR and BDR reduce full-adjacency fanout; elections depend on eligible interface priorities and router IDs, and are not always preemptive.
- A stub area generally suppresses external Type 5 LSAs, while an NSSA can inject external prefixes as Type 7 LSAs for translation at an ABR under configured conditions.
- ABRs can advertise summary information between areas while routing policy and area ranges alter which routes are visible; overly broad aggregation can blackhole traffic if specifics lack coverage.
- IS-IS hello compatibility requires suitable circuit level, area relation for Level 1, supported MTU/parameters and authentication; physical link Up alone is insufficient.
Explanation
Correct Answer
C:The relevant Junos service-provider networking principle is: ABRs can advertise summary information between areas while routing policy and area ranges alter which routes are visible; overly broad aggregation can blackhole traffic if specifics lack coverage. In the described provider-network case (An ISP aggregates several access loopback prefixes between areas, but one unassigned address range in the summary attracts traffic with no valid downstream path.), it supports the planned action: Apply summarization or import/export controls at the appropriate OSPF area boundary after proving which access prefixes should be reachable.
Incorrect Answers
A:This alternative proposes: On an OSPF broadcast network a DR and BDR reduce full-adjacency fanout; elections depend on eligible interface priorities and router IDs, and are not always preemptive. It concerns a different Junos engineering issue OSPF designated router election on a multiaccess segment, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
B:This alternative proposes: A stub area generally suppresses external Type 5 LSAs, while an NSSA can inject external prefixes as Type 7 LSAs for translation at an ABR under configured conditions. It concerns a different Junos engineering issue OSPF stub NSSA and external LSA handling, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
D:This alternative proposes: IS-IS hello compatibility requires suitable circuit level, area relation for Level 1, supported MTU/parameters and authentication; physical link Up alone is insufficient. It concerns a different Junos engineering issue IS-IS adjacency NET and interface mismatch troubleshooting, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
Question 63
A Juniper service-provider engineer needs decisive verification evidence for this situation. An ISP aggregates several access loopback prefixes between areas, but one unassigned address range in the summary attracts traffic with no valid downstream path. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.
- Inspect show ospf neighbor detail, interface MTU, hello/dead timers, authentication, area settings, and database exchange errors on both routers.
- Inspect specific prefixes at the ABR, area range configuration, policy match criteria, summary LSA presence and forwarding toward the aggregated destinations.
- Review show pim neighbors, RP mapping, IGMP membership, PIM joins, source registration and multicast forwarding entries for affected groups.
- Check area IDs, ABR relationships, backbone LSA visibility, virtual-link state, and show ospf neighbor and database before adjusting policies.
Explanation
Correct Answer
B:The direct discriminating observation is: Inspect specific prefixes at the ABR, area range configuration, policy match criteria, summary LSA presence and forwarding toward the aggregated destinations. In the stated situation (An ISP aggregates several access loopback prefixes between areas, but one unassigned address range in the summary attracts traffic with no valid downstream path.), the intended acceptance outcome is: Core route volume decreases while every authorized covered access subnet remains reachable and unintended prefixes stay filtered.
Incorrect Answers
A:This alternative proposes: Inspect show ospf neighbor detail, interface MTU, hello/dead timers, authentication, area settings, and database exchange errors on both routers. It concerns a different Junos engineering issue OSPF adjacency MTU and hello compatibility diagnosis, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
C:This alternative proposes: Review show pim neighbors, RP mapping, IGMP membership, PIM joins, source registration and multicast forwarding entries for affected groups. It concerns a different Junos engineering issue PIM sparse mode rendezvous point and shared tree operation, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
D:This alternative proposes: Check area IDs, ABR relationships, backbone LSA visibility, virtual-link state, and show ospf neighbor and database before adjusting policies. It concerns a different Junos engineering issue OSPF multi-area backbone connectivity and virtual-link limitations, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
Question 64
A service-provider acceptance team reviews the result of a provider-service change. An ISP aggregates several access loopback prefixes between areas, but one unassigned address range in the summary attracts traffic with no valid downstream path. The intended verification is: Inspect specific prefixes at the ABR, area range configuration, policy match criteria, summary LSA presence and forwarding toward the aggregated destinations. Which outcome BEST demonstrates success? Select ONE best answer.
- Core route volume decreases while every authorized covered access subnet remains reachable and unintended prefixes stay filtered.
- The intended external subnet is reachable under the area policy without exposing all provider external LSAs to remote access routers.
- The intended remote VPN site can reach its authorized peer across the AS boundary without transferring unrelated tenants' routes or losing required label resolution.
- The neighbor reaches Full, both routers synchronize the relevant link-state database, and no unrelated adjacencies are disrupted.
Explanation
Correct Answer
A:The verified success outcome is: Core route volume decreases while every authorized covered access subnet remains reachable and unintended prefixes stay filtered. Confirm this by: Inspect specific prefixes at the ABR, area range configuration, policy match criteria, summary LSA presence and forwarding toward the aggregated destinations.
Incorrect Answers
B:That option concerns OSPF stub NSSA and external LSA handling. The related controlled intervention is: Apply summarization or import/export controls at the appropriate OSPF area boundary after proving which access prefixes should be reachable.
C:That option concerns Interprovider Layer 3 VPN options and carrier of carriers. The related controlled intervention is: Apply summarization or import/export controls at the appropriate OSPF area boundary after proving which access prefixes should be reachable.
D:This alternative proposes: The neighbor reaches Full, both routers synchronize the relevant link-state database, and no unrelated adjacencies are disrupted. It concerns a different Junos engineering issue OSPF adjacency MTU and hello compatibility diagnosis, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
Question 65
A Junos service-provider routing engineer investigates this service-provider network scenario. An ISP aggregates several access loopback prefixes between areas, but one unassigned address range in the summary attracts traffic with no valid downstream path. Which TWO complementary steps combine a suitable technical action and its direct verification? Select TWO answers.
- Inspect show ospf3 neighbor, show ospf3 interface, IPv6 link-local addresses, area association, LSDB and inet6 routes independently of OSPFv2.
- Validate candidate BGP FlowSpec rules against agreed DDoS filtering policy and propagation controls before applying them to production forwarding hardware.
- Trace an LDP Layer 2 circuit end to end using neighbor signaling, pseudowire identifiers and operational connection state before changing customer VLANs.
- Apply summarization or import/export controls at the appropriate OSPF area boundary after proving which access prefixes should be reachable.
- Inspect specific prefixes at the ABR, area range configuration, policy match criteria, summary LSA presence and forwarding toward the aggregated destinations.
Explanation
Correct Answers
D:The case-specific routing and services action is: Apply summarization or import/export controls at the appropriate OSPF area boundary after proving which access prefixes should be reachable. The governing Junos routing/service principle is: ABRs can advertise summary information between areas while routing policy and area ranges alter which routes are visible; overly broad aggregation can blackhole traffic if specifics lack coverage.
E:The direct discriminating observation is: Inspect specific prefixes at the ABR, area range configuration, policy match criteria, summary LSA presence and forwarding toward the aggregated destinations.
Incorrect Answers
A:This alternative proposes: Inspect show ospf3 neighbor, show ospf3 interface, IPv6 link-local addresses, area association, LSDB and inet6 routes independently of OSPFv2. It concerns a different Junos engineering issue OSPFv3 IPv6 neighbor and IPv4 separation, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
B:This alternative proposes: Validate candidate BGP FlowSpec rules against agreed DDoS filtering policy and propagation controls before applying them to production forwarding hardware. It concerns a different Junos engineering issue BGP FlowSpec validation and filtering boundaries, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
C:This alternative proposes: Trace an LDP Layer 2 circuit end to end using neighbor signaling, pseudowire identifiers and operational connection state before changing customer VLANs. It concerns a different Junos engineering issue LDP signaled Layer 2 circuit pseudowire status and VC identifiers, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions in the stated situation (An ISP aggregates several access loopback prefixes between areas, but one unassigned address range in the summary attracts traffic with no valid downstream path.). A better case-specific check is: Inspect specific prefixes at the ABR, area range configuration, policy match criteria, summary LSA presence and forwarding toward the aggregated destinations. The more targeted action is: Apply summarization or import/export controls at the appropriate OSPF area boundary after proving which access prefixes should be reachable.
Question 66
A Junos service-provider routing engineer investigates the following routing and service incident: A security policy is intended to suppress one test prefix yet accidentally rejects all interarea summaries into a production OSPF backbone. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.
- Use BGP communities as controlled signals for provider routing policies instead of confusing tagging with guaranteed remote traffic behavior.
- Apply summarization or import/export controls at the appropriate OSPF area boundary after proving which access prefixes should be reachable.
- Inspect broadcast-network DR and BDR election state and interface priority before attempting to control database exchange behavior on an Ethernet shared segment.
- Validate that all nonbackbone OSPF areas have a supported logical connection to area 0, and use virtual links only as a documented transitional design.
Explanation
Correct Answer
B:The case-specific routing and services action is: Apply summarization or import/export controls at the appropriate OSPF area boundary after proving which access prefixes should be reachable. The governing Junos routing/service principle is: ABRs can advertise summary information between areas while routing policy and area ranges alter which routes are visible; overly broad aggregation can blackhole traffic if specifics lack coverage. Verify the decision through: Inspect specific prefixes at the ABR, area range configuration, policy match criteria, summary LSA presence and forwarding toward the aggregated destinations.
Incorrect Answers
A:This alternative proposes: Use BGP communities as controlled signals for provider routing policies instead of confusing tagging with guaranteed remote traffic behavior. It concerns a different Junos engineering issue BGP communities and selective transit routing policy, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
C:This alternative proposes: Inspect broadcast-network DR and BDR election state and interface priority before attempting to control database exchange behavior on an Ethernet shared segment. It concerns a different Junos engineering issue OSPF designated router election on a multiaccess segment, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
D:This alternative proposes: Validate that all nonbackbone OSPF areas have a supported logical connection to area 0, and use virtual links only as a documented transitional design. It concerns a different Junos engineering issue OSPF multi-area backbone connectivity and virtual-link limitations, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
Question 67
A provider routing design review considers this situation. A security policy is intended to suppress one test prefix yet accidentally rejects all interarea summaries into a production OSPF backbone. A colleague proposes: Apply summarization or import/export controls at the appropriate OSPF area boundary after proving which access prefixes should be reachable. Which technical principle BEST supports that action? Select ONE best answer.
- A stub area generally suppresses external Type 5 LSAs, while an NSSA can inject external prefixes as Type 7 LSAs for translation at an ABR under configured conditions.
- ABRs can advertise summary information between areas while routing policy and area ranges alter which routes are visible; overly broad aggregation can blackhole traffic if specifics lack coverage.
- OSPFv3 uses IPv6-related control-plane processing and link-local neighbor communication; it must be configured and verified according to the selected address family and release.
- ASM PIM-SM may use a rendezvous point for rendezvous and shared tree creation, after which routers can move eligible traffic onto source-based trees.
Explanation
Correct Answer
B:The relevant Junos service-provider networking principle is: ABRs can advertise summary information between areas while routing policy and area ranges alter which routes are visible; overly broad aggregation can blackhole traffic if specifics lack coverage. In the described provider-network case (A security policy is intended to suppress one test prefix yet accidentally rejects all interarea summaries into a production OSPF backbone.), it supports the planned action: Apply summarization or import/export controls at the appropriate OSPF area boundary after proving which access prefixes should be reachable.
Incorrect Answers
A:This alternative proposes: A stub area generally suppresses external Type 5 LSAs, while an NSSA can inject external prefixes as Type 7 LSAs for translation at an ABR under configured conditions. It concerns a different Junos engineering issue OSPF stub NSSA and external LSA handling, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
C:This alternative proposes: OSPFv3 uses IPv6-related control-plane processing and link-local neighbor communication; it must be configured and verified according to the selected address family and release. It concerns a different Junos engineering issue OSPFv3 IPv6 neighbor and IPv4 separation, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
D:This alternative proposes: ASM PIM-SM may use a rendezvous point for rendezvous and shared tree creation, after which routers can move eligible traffic onto source-based trees. It concerns a different Junos engineering issue PIM sparse mode rendezvous point and shared tree operation, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
Question 68
A Juniper service-provider engineer needs decisive verification evidence for this situation. A security policy is intended to suppress one test prefix yet accidentally rejects all interarea summaries into a production OSPF backbone. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.
- Examine scheduler-map bindings, allocated rates, interface queue statistics, high-priority activity and low-priority drain rate under load.
- Inspect specific prefixes at the ABR, area range configuration, policy match criteria, summary LSA presence and forwarding toward the aggregated destinations.
- Compare show ospf interface, election priorities, router IDs, two-way versus full neighbors, and current DR/BDR state after planned link transitions.
- Review ASBR origin, advertised external metric type, internal path-to-ASBR cost, routing table preferences, and selected next hops at each PE.
Explanation
Correct Answer
B:The direct discriminating observation is: Inspect specific prefixes at the ABR, area range configuration, policy match criteria, summary LSA presence and forwarding toward the aggregated destinations. In the stated situation (A security policy is intended to suppress one test prefix yet accidentally rejects all interarea summaries into a production OSPF backbone.), the intended acceptance outcome is: Core route volume decreases while every authorized covered access subnet remains reachable and unintended prefixes stay filtered.
Incorrect Answers
A:This alternative proposes: Examine scheduler-map bindings, allocated rates, interface queue statistics, high-priority activity and low-priority drain rate under load. It concerns a different Junos engineering issue CoS schedulers scheduler-maps and bandwidth sharing, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
C:This alternative proposes: Compare show ospf interface, election priorities, router IDs, two-way versus full neighbors, and current DR/BDR state after planned link transitions. It concerns a different Junos engineering issue OSPF designated router election on a multiaccess segment, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
D:This alternative proposes: Review ASBR origin, advertised external metric type, internal path-to-ASBR cost, routing table preferences, and selected next hops at each PE. It concerns a different Junos engineering issue OSPF external type E1 E2 route cost evaluation, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
Question 69
A service-provider acceptance team reviews the result of a provider-service change. A security policy is intended to suppress one test prefix yet accidentally rejects all interarea summaries into a production OSPF backbone. The intended verification is: Inspect specific prefixes at the ABR, area range configuration, policy match criteria, summary LSA presence and forwarding toward the aggregated destinations. Which outcome BEST demonstrates success? Select ONE best answer.
- The appropriate designated and backup routers maintain required adjacencies and exchange reachability across the shared Ethernet without unnecessary resets.
- Core route volume decreases while every authorized covered access subnet remains reachable and unintended prefixes stay filtered.
- Traffic shares suitable eligible next hops according to supported hashing behavior and fails over without blackholing during neighbor loss.
- The neighbor reaches Full, both routers synchronize the relevant link-state database, and no unrelated adjacencies are disrupted.
Explanation
Correct Answer
B:The verified success outcome is: Core route volume decreases while every authorized covered access subnet remains reachable and unintended prefixes stay filtered. Confirm this by: Inspect specific prefixes at the ABR, area range configuration, policy match criteria, summary LSA presence and forwarding toward the aggregated destinations. The related controlled intervention is: Apply summarization or import/export controls at the appropriate OSPF area boundary after proving which access prefixes should be reachable.
Incorrect Answers
A:That option concerns OSPF designated router election on a multiaccess segment. The related controlled intervention is: Apply summarization or import/export controls at the appropriate OSPF area boundary after proving which access prefixes should be reachable.
C:That option concerns BGP multipath equal cost and per-flow forwarding. The related controlled intervention is: Apply summarization or import/export controls at the appropriate OSPF area boundary after proving which access prefixes should be reachable.
D:This alternative proposes: The neighbor reaches Full, both routers synchronize the relevant link-state database, and no unrelated adjacencies are disrupted. It concerns a different Junos engineering issue OSPF adjacency MTU and hello compatibility diagnosis, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
Question 70
A Junos routing design reviewer evaluates an unsafe shortcut in this network customer scenario. A security policy is intended to suppress one test prefix yet accidentally rejects all interarea summaries into a production OSPF backbone. Which assumption is MOST DIRECTLY dangerous or unsupported? Select ONE best answer.
- Assume an ASM PIM-SM network never needs any RP configuration or discovery because IGMP listeners exist at the leaf router.
- Configure one router in a shared area as NSSA while leaving its peer as a normal stub area and expect their adjacency and external imports to work.
- Install a summary for discontiguous customer access blocks and drop all component routes without verifying that the ABR actually forwards the entire aggregate.
- Declare that a Type 2 external metric always equals the sum of backbone hop costs and must be changed whenever an IGP link cost changes.
Explanation
Correct Answer
C:That conflicts with the edge-to-cloud principle: ABRs can advertise summary information between areas while routing policy and area ranges alter which routes are visible; overly broad aggregation can blackhole traffic if specifics lack coverage.
Incorrect Answers
A:This alternative proposes: Assume an ASM PIM-SM network never needs any RP configuration or discovery because IGMP listeners exist at the leaf router. It concerns a different Junos engineering issue PIM sparse mode rendezvous point and shared tree operation, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
B:This alternative proposes: Configure one router in a shared area as NSSA while leaving its peer as a normal stub area and expect their adjacency and external imports to work. It concerns a different Junos engineering issue OSPF stub NSSA and external LSA handling, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
D:This alternative proposes: Declare that a Type 2 external metric always equals the sum of backbone hop costs and must be changed whenever an IGP link cost changes. It concerns a different Junos engineering issue OSPF external type E1 E2 route cost evaluation, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.