Juniper JN0-664 Practice Test 8
Question 70
A Junos routing design reviewer evaluates an unsafe shortcut in this network customer scenario. A security policy is intended to suppress one test prefix yet accidentally rejects all interarea summaries into a production OSPF backbone. Which assumption is MOST DIRECTLY dangerous or unsupported? Select ONE best answer.
- Assume an ASM PIM-SM network never needs any RP configuration or discovery because IGMP listeners exist at the leaf router.
- Configure one router in a shared area as NSSA while leaving its peer as a normal stub area and expect their adjacency and external imports to work.
- Install a summary for discontiguous customer access blocks and drop all component routes without verifying that the ABR actually forwards the entire aggregate.
- Declare that a Type 2 external metric always equals the sum of backbone hop costs and must be changed whenever an IGP link cost changes.
Explanation
Correct Answer
C:That conflicts with the edge-to-cloud principle: ABRs can advertise summary information between areas while routing policy and area ranges alter which routes are visible; overly broad aggregation can blackhole traffic if specifics lack coverage.
Incorrect Answers
A:This alternative proposes: Assume an ASM PIM-SM network never needs any RP configuration or discovery because IGMP listeners exist at the leaf router. It concerns a different Junos engineering issue PIM sparse mode rendezvous point and shared tree operation, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
B:This alternative proposes: Configure one router in a shared area as NSSA while leaving its peer as a normal stub area and expect their adjacency and external imports to work. It concerns a different Junos engineering issue OSPF stub NSSA and external LSA handling, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
D:This alternative proposes: Declare that a Type 2 external metric always equals the sum of backbone hop costs and must be changed whenever an IGP link cost changes. It concerns a different Junos engineering issue OSPF external type E1 E2 route cost evaluation, not the directly tested provider-network issue OSPF interarea route summarization and route restrictions.
Question 71
A Junos service-provider routing engineer investigates the following routing and service incident: An access area loses reachability to another region after an operator inadvertently disables Level 2 on the shared border router. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.
- Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP.
- Examine external route Type 1 versus Type 2 cost behavior and the forwarding cost toward the ASBR when determining why routers choose different exits.
- Diagnose divergent IS-IS topology by tracing LSP sequences, database scope and complete sequence-number packet exchange.
- Investigate rejected or down IS-IS adjacencies by verifying circuit levels, IS-IS NET identifiers, authentication and interface MTU before changing the full IGP.
Explanation
Correct Answer
A:Level 1 routers know their local IS-IS area, Level 2 routers maintain interarea connectivity, and L1/L2 systems can provide area exits with suitable reachability and attached signaling. Compare NET area addresses, circuit levels, show isis adjacency detail, L1 versus L2 route tables and the attached bit on designated exits.
Incorrect Answers
B:This alternative proposes: Examine external route Type 1 versus Type 2 cost behavior and the forwarding cost toward the ASBR when determining why routers choose different exits. It concerns a different Junos engineering issue OSPF external type E1 E2 route cost evaluation, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
C:This alternative proposes: Diagnose divergent IS-IS topology by tracing LSP sequences, database scope and complete sequence-number packet exchange. It concerns a different Junos engineering issue IS-IS link-state packet flooding and database consistency, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
D:This alternative proposes: Investigate rejected or down IS-IS adjacencies by verifying circuit levels, IS-IS NET identifiers, authentication and interface MTU before changing the full IGP. It concerns a different Junos engineering issue IS-IS adjacency NET and interface mismatch troubleshooting, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
Question 72
A provider routing design review considers this situation. An access area loses reachability to another region after an operator inadvertently disables Level 2 on the shared border router. A colleague proposes: Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP. Which technical principle BEST supports that action? Select ONE best answer.
- Level 1 routers know their local IS-IS area, Level 2 routers maintain interarea connectivity, and L1/L2 systems can provide area exits with suitable reachability and attached signaling.
- An L1 network may rely on attached/default routing toward L1/L2 routers; deliberate interlevel leaking or summarization can expose selected routes without making every area full Level 2.
- ASM PIM-SM may use a rendezvous point for rendezvous and shared tree creation, after which routers can move eligible traffic onto source-based trees.
- IS-IS hello compatibility requires suitable circuit level, area relation for Level 1, supported MTU/parameters and authentication; physical link Up alone is insufficient.
Explanation
Correct Answer
A:The relevant Junos service-provider networking principle is: Level 1 routers know their local IS-IS area, Level 2 routers maintain interarea connectivity, and L1/L2 systems can provide area exits with suitable reachability and attached signaling. In the described provider-network case (An access area loses reachability to another region after an operator inadvertently disables Level 2 on the shared border router.), it supports the planned action: Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP.
Incorrect Answers
B:This alternative proposes: An L1 network may rely on attached/default routing toward L1/L2 routers; deliberate interlevel leaking or summarization can expose selected routes without making every area full Level 2. It concerns a different Junos engineering issue IS-IS Level 2 to Level 1 route leaking and summaries, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
C:This alternative proposes: ASM PIM-SM may use a rendezvous point for rendezvous and shared tree creation, after which routers can move eligible traffic onto source-based trees. It concerns a different Junos engineering issue PIM sparse mode rendezvous point and shared tree operation, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
D:This alternative proposes: IS-IS hello compatibility requires suitable circuit level, area relation for Level 1, supported MTU/parameters and authentication; physical link Up alone is insufficient. It concerns a different Junos engineering issue IS-IS adjacency NET and interface mismatch troubleshooting, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
Question 73
A Juniper service-provider engineer needs decisive verification evidence for this situation. An access area loses reachability to another region after an operator inadvertently disables Level 2 on the shared border router. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.
- Review route-policy terms, L1 and L2 route databases, leaked prefix entries, interface scope and next-hop resolution from affected access devices.
- Inspect SSM group range, IGMPv3 (S,G) membership, source unicast route, RPF state, PIM joins and actual packet counts.
- Compare NET area addresses, circuit levels, show isis adjacency detail, L1 versus L2 route tables and the attached bit on designated exits.
- Compare show isis database, LSP sequence numbers, CSNP/PSNP exchange, interface errors and per-level adjacency status for the affected path.
Explanation
Correct Answer
C:In the stated situation (An access area loses reachability to another region after an operator inadvertently disables Level 2 on the shared border router.), the intended acceptance outcome is: Each subscriber region reaches its own internal endpoints and approved destinations through the selected L1/L2 border systems without losing its default path.
Incorrect Answers
A:This alternative proposes: Review route-policy terms, L1 and L2 route databases, leaked prefix entries, interface scope and next-hop resolution from affected access devices. It concerns a different Junos engineering issue IS-IS Level 2 to Level 1 route leaking and summaries, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
B:This alternative proposes: Inspect SSM group range, IGMPv3 (S,G) membership, source unicast route, RPF state, PIM joins and actual packet counts. It concerns a different Junos engineering issue Source-specific multicast and IGMPv3 source filtering, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
D:This alternative proposes: Compare show isis database, LSP sequence numbers, CSNP/PSNP exchange, interface errors and per-level adjacency status for the affected path. It concerns a different Junos engineering issue IS-IS link-state packet flooding and database consistency, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
Question 74
A service-provider acceptance team reviews the result of a provider-service change. An access area loses reachability to another region after an operator inadvertently disables Level 2 on the shared border router. The intended verification is: Compare NET area addresses, circuit levels, show isis adjacency detail, L1 versus L2 route tables and the attached bit on designated exits. Which outcome BEST demonstrates success? Select ONE best answer.
- The neighbor reaches Full, both routers synchronize the relevant link-state database, and no unrelated adjacencies are disrupted.
- The expected DIS represents the shared LAN in the LSDB and routes converge when a controlled election change takes place.
- Each subscriber region reaches its own internal endpoints and approved destinations through the selected L1/L2 border systems without losing its default path.
- Neighbor databases converge on consistent current LSPs and the intended network prefixes resolve through matching shortest-path computations.
Explanation
Correct Answer
C:The verified success outcome is: Each subscriber region reaches its own internal endpoints and approved destinations through the selected L1/L2 border systems without losing its default path. Confirm this by: Compare NET area addresses, circuit levels, show isis adjacency detail, L1 versus L2 route tables and the attached bit on designated exits.
Incorrect Answers
A:That option concerns OSPF adjacency MTU and hello compatibility diagnosis. The related controlled intervention is: Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP.
B:That option concerns IS-IS DIS pseudonode and broadcast circuit election. The related controlled intervention is: Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP.
D:That option concerns IS-IS link-state packet flooding and database consistency. The related controlled intervention is: Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP.
Question 75
A Junos service-provider routing engineer investigates this service-provider network scenario. An access area loses reachability to another region after an operator inadvertently disables Level 2 on the shared border router. Which TWO complementary steps combine a suitable technical action and its direct verification? Select TWO answers.
- Run show isis adjacency extensive, inspect down reason, show isis interface, interface errors, NET area values, hello parameters and authentication state on both neighbors.
- Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP.
- Compare NET area addresses, circuit levels, show isis adjacency detail, L1 versus L2 route tables and the attached bit on designated exits.
- Diagnose unknown unicast flooding and Layer 2 loops by distinguishing learned customer MAC paths, BUM handling and VPLS split-horizon behavior.
- Validate candidate BGP FlowSpec rules against agreed DDoS filtering policy and propagation controls before applying them to production forwarding hardware.
Explanation
Correct Answers
B:The case-specific routing and services action is: Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP. The governing Junos routing/service principle is: Level 1 routers know their local IS-IS area, Level 2 routers maintain interarea connectivity, and L1/L2 systems can provide area exits with suitable reachability and attached signaling.
C:The direct discriminating observation is: Compare NET area addresses, circuit levels, show isis adjacency detail, L1 versus L2 route tables and the attached bit on designated exits. In the stated situation (An access area loses reachability to another region after an operator inadvertently disables Level 2 on the shared border router.), the intended acceptance outcome is: Each subscriber region reaches its own internal endpoints and approved destinations through the selected L1/L2 border systems without losing its default path.
Incorrect Answers
A:This alternative proposes: Run show isis adjacency extensive, inspect down reason, show isis interface, interface errors, NET area values, hello parameters and authentication state on both neighbors. It concerns a different Junos engineering issue IS-IS adjacency NET and interface mismatch troubleshooting, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
D:This alternative proposes: Diagnose unknown unicast flooding and Layer 2 loops by distinguishing learned customer MAC paths, BUM handling and VPLS split-horizon behavior. It concerns a different Junos engineering issue VPLS MAC learning flooding and split-horizon safeguards, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
E:This alternative proposes: Validate candidate BGP FlowSpec rules against agreed DDoS filtering policy and propagation controls before applying them to production forwarding hardware. It concerns a different Junos engineering issue BGP FlowSpec validation and filtering boundaries, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
Question 76
A Junos service-provider routing engineer investigates the following routing and service incident: A provider adds a new IS-IS area but assigns all edge routers to Level 1 only and assumes they will independently discover routes in remote areas. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.
- Plan VPLS multihoming with supported service site identifiers, redundancy roles and failover controls to avoid a duplicate active attachment loop.
- Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP.
- Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
- Investigate rejected or down IS-IS adjacencies by verifying circuit levels, IS-IS NET identifiers, authentication and interface MTU before changing the full IGP.
Explanation
Correct Answer
B:The case-specific routing and services action is: Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP. The governing Junos routing/service principle is: Level 1 routers know their local IS-IS area, Level 2 routers maintain interarea connectivity, and L1/L2 systems can provide area exits with suitable reachability and attached signaling. Verify the decision through: Compare NET area addresses, circuit levels, show isis adjacency detail, L1 versus L2 route tables and the attached bit on designated exits.
Incorrect Answers
A:This alternative proposes: Plan VPLS multihoming with supported service site identifiers, redundancy roles and failover controls to avoid a duplicate active attachment loop. It concerns a different Junos engineering issue VPLS site identifiers multihoming and service convergence, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
C:This alternative proposes: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm. It concerns a different Junos engineering issue IS-IS DIS pseudonode and broadcast circuit election, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
D:This alternative proposes: Investigate rejected or down IS-IS adjacencies by verifying circuit levels, IS-IS NET identifiers, authentication and interface MTU before changing the full IGP. It concerns a different Junos engineering issue IS-IS adjacency NET and interface mismatch troubleshooting, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
Question 77
A provider routing design review considers this situation. A provider adds a new IS-IS area but assigns all edge routers to Level 1 only and assumes they will independently discover routes in remote areas. A colleague proposes: Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP. Which technical principle BEST supports that action? Select ONE best answer.
- IS-IS wide metrics support extended values and modern topology use cases, but cost selection depends on configured interface metrics and supported protocol behavior.
- Level 1 routers know their local IS-IS area, Level 2 routers maintain interarea connectivity, and L1/L2 systems can provide area exits with suitable reachability and attached signaling.
- IS-IS elects a DIS on a broadcast segment to originate pseudonode information; it has no OSPF-style separately elected backup designated router, and election behavior differs.
- IPv6 Layer 3 VPN routes use address-family-specific control-plane and forwarding information; a working IPv4 tenant VRF does not itself establish IPv6 connectivity.
Explanation
Correct Answer
B:The relevant Junos service-provider networking principle is: Level 1 routers know their local IS-IS area, Level 2 routers maintain interarea connectivity, and L1/L2 systems can provide area exits with suitable reachability and attached signaling. In the described provider-network case (A provider adds a new IS-IS area but assigns all edge routers to Level 1 only and assumes they will independently discover routes in remote areas.), it supports the planned action: Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP.
Incorrect Answers
A:This alternative proposes: IS-IS wide metrics support extended values and modern topology use cases, but cost selection depends on configured interface metrics and supported protocol behavior. It concerns a different Junos engineering issue IS-IS wide metrics traffic engineering and cost selection, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
C:This alternative proposes: IS-IS elects a DIS on a broadcast segment to originate pseudonode information; it has no OSPF-style separately elected backup designated router, and election behavior differs. It concerns a different Junos engineering issue IS-IS DIS pseudonode and broadcast circuit election, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
D:This alternative proposes: IPv6 Layer 3 VPN routes use address-family-specific control-plane and forwarding information; a working IPv4 tenant VRF does not itself establish IPv6 connectivity. It concerns a different Junos engineering issue IPv6 Layer 3 VPN VPNv6 route families and forwarding, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
Question 78
A Juniper service-provider engineer needs decisive verification evidence for this situation. A provider adds a new IS-IS area but assigns all edge routers to Level 1 only and assumes they will independently discover routes in remote areas. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.
- Compare show isis database, LSP sequence numbers, CSNP/PSNP exchange, interface errors and per-level adjacency status for the affected path.
- Review forwarding-class definitions, queue identifiers, packet-loss priority classification, interface CoS output and measured packet counters.
- Compare NET area addresses, circuit levels, show isis adjacency detail, L1 versus L2 route tables and the attached bit on designated exits.
- Review show isis interface detail, LAN priority, circuit level, elected DIS, neighbor states and pseudonode LSP records.
Explanation
Correct Answer
C:The direct discriminating observation is: Compare NET area addresses, circuit levels, show isis adjacency detail, L1 versus L2 route tables and the attached bit on designated exits. In the stated situation (A provider adds a new IS-IS area but assigns all edge routers to Level 1 only and assumes they will independently discover routes in remote areas.), the intended acceptance outcome is: Each subscriber region reaches its own internal endpoints and approved destinations through the selected L1/L2 border systems without losing its default path.
Incorrect Answers
A:This alternative proposes: Compare show isis database, LSP sequence numbers, CSNP/PSNP exchange, interface errors and per-level adjacency status for the affected path. It concerns a different Junos engineering issue IS-IS link-state packet flooding and database consistency, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
B:This alternative proposes: Review forwarding-class definitions, queue identifiers, packet-loss priority classification, interface CoS output and measured packet counters. It concerns a different Junos engineering issue CoS forwarding classes packet-loss priority and egress queue binding, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
D:This alternative proposes: Review show isis interface detail, LAN priority, circuit level, elected DIS, neighbor states and pseudonode LSP records. It concerns a different Junos engineering issue IS-IS DIS pseudonode and broadcast circuit election, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
Question 79
A service-provider acceptance team reviews the result of a provider-service change. A provider adds a new IS-IS area but assigns all edge routers to Level 1 only and assumes they will independently discover routes in remote areas. The intended verification is: Compare NET area addresses, circuit levels, show isis adjacency detail, L1 versus L2 route tables and the attached bit on designated exits. Which outcome BEST demonstrates success? Select ONE best answer.
- Traffic shares suitable eligible next hops according to supported hashing behavior and fails over without blackholing during neighbor loss.
- Traffic prefers the engineered feasible lower-cost path and uses a documented alternate when a critical link fails.
- Neighbor state reaches Up at the expected level and routing recovers without exposing a different operator's area or changing every circuit.
- Each subscriber region reaches its own internal endpoints and approved destinations through the selected L1/L2 border systems without losing its default path.
Explanation
Correct Answer
D:The verified success outcome is: Each subscriber region reaches its own internal endpoints and approved destinations through the selected L1/L2 border systems without losing its default path. Confirm this by: Compare NET area addresses, circuit levels, show isis adjacency detail, L1 versus L2 route tables and the attached bit on designated exits. The related controlled intervention is: Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP.
Incorrect Answers
A:That option concerns BGP multipath equal cost and per-flow forwarding. The related controlled intervention is: Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP.
B:That option concerns IS-IS wide metrics traffic engineering and cost selection. The related controlled intervention is: Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP.
C:That option concerns IS-IS adjacency NET and interface mismatch troubleshooting. The related controlled intervention is: Separate Level 1 intra-area and Level 2 inter-area IS-IS forwarding responsibilities when building a multi-area service-provider IGP.
Question 80
A Junos routing design reviewer evaluates an unsafe shortcut in this network customer scenario. A provider adds a new IS-IS area but assigns all edge routers to Level 1 only and assumes they will independently discover routes in remote areas. Which assumption is MOST DIRECTLY dangerous or unsupported? Select ONE best answer.
- Treat an IS-IS DIS as permanently paired with a mandatory BDR and declare the broadcast domain broken when a backup election is not shown.
- Treat a customer's multi-site VPN backdoor link as automatically equivalent to an OSPF intra-area backbone path and disable all route-loop safeguards.
- Assume a core link with more bandwidth automatically has the lowest IS-IS metric when no operator metric policy has been configured.
- Expect two pure Level 1 routers in different IS-IS areas to exchange routes directly across the core without an eligible Level 2 path.
Explanation
Correct Answer
D:That conflicts with the edge-to-cloud principle: Level 1 routers know their local IS-IS area, Level 2 routers maintain interarea connectivity, and L1/L2 systems can provide area exits with suitable reachability and attached signaling.
Incorrect Answers
A:This alternative proposes: Treat an IS-IS DIS as permanently paired with a mandatory BDR and declare the broadcast domain broken when a backup election is not shown. It concerns a different Junos engineering issue IS-IS DIS pseudonode and broadcast circuit election, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
B:This alternative proposes: Treat a customer's multi-site VPN backdoor link as automatically equivalent to an OSPF intra-area backbone path and disable all route-loop safeguards. It concerns a different Junos engineering issue Site of Origin and OSPF sham-link loop control, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
C:This alternative proposes: Assume a core link with more bandwidth automatically has the lowest IS-IS metric when no operator metric policy has been configured. It concerns a different Junos engineering issue IS-IS wide metrics traffic engineering and cost selection, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.