Juniper JN0-664 Practice Test 9
Question 80
A Junos routing design reviewer evaluates an unsafe shortcut in this network customer scenario. A provider adds a new IS-IS area but assigns all edge routers to Level 1 only and assumes they will independently discover routes in remote areas. Which assumption is MOST DIRECTLY dangerous or unsupported? Select ONE best answer.
- Treat an IS-IS DIS as permanently paired with a mandatory BDR and declare the broadcast domain broken when a backup election is not shown.
- Treat a customer's multi-site VPN backdoor link as automatically equivalent to an OSPF intra-area backbone path and disable all route-loop safeguards.
- Assume a core link with more bandwidth automatically has the lowest IS-IS metric when no operator metric policy has been configured.
- Expect two pure Level 1 routers in different IS-IS areas to exchange routes directly across the core without an eligible Level 2 path.
Explanation
Correct Answer
D:That conflicts with the edge-to-cloud principle: Level 1 routers know their local IS-IS area, Level 2 routers maintain interarea connectivity, and L1/L2 systems can provide area exits with suitable reachability and attached signaling.
Incorrect Answers
A:This alternative proposes: Treat an IS-IS DIS as permanently paired with a mandatory BDR and declare the broadcast domain broken when a backup election is not shown. It concerns a different Junos engineering issue IS-IS DIS pseudonode and broadcast circuit election, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
B:This alternative proposes: Treat a customer's multi-site VPN backdoor link as automatically equivalent to an OSPF intra-area backbone path and disable all route-loop safeguards. It concerns a different Junos engineering issue Site of Origin and OSPF sham-link loop control, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
C:This alternative proposes: Assume a core link with more bandwidth automatically has the lowest IS-IS metric when no operator metric policy has been configured. It concerns a different Junos engineering issue IS-IS wide metrics traffic engineering and cost selection, not the directly tested provider-network issue IS-IS level one level two hierarchy and area boundaries.
Question 81
A Junos service-provider routing engineer investigates the following routing and service incident: On a provider Ethernet segment, an operator searches for a BDR field in Junos IS-IS output and concludes no resilience exists. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.
- Investigate rejected or down IS-IS adjacencies by verifying circuit levels, IS-IS NET identifiers, authentication and interface MTU before changing the full IGP.
- Deploy BGP route reflection to scale iBGP while monitoring originator-id and cluster-list loop prevention and correct client membership.
- Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
- Check whether the deployed IS-IS metric style and link costs support the provider's intended routing and traffic-engineering behavior.
Explanation
Correct Answer
C:The case-specific routing and services action is: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm. The governing Junos routing/service principle is: IS-IS elects a DIS on a broadcast segment to originate pseudonode information; it has no OSPF-style separately elected backup designated router, and election behavior differs.
Incorrect Answers
A:This alternative proposes: Investigate rejected or down IS-IS adjacencies by verifying circuit levels, IS-IS NET identifiers, authentication and interface MTU before changing the full IGP. It concerns a different Junos engineering issue IS-IS adjacency NET and interface mismatch troubleshooting, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
B:This alternative proposes: Deploy BGP route reflection to scale iBGP while monitoring originator-id and cluster-list loop prevention and correct client membership. It concerns a different Junos engineering issue BGP route reflectors originator and cluster loop prevention, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
D:This alternative proposes: Check whether the deployed IS-IS metric style and link costs support the provider's intended routing and traffic-engineering behavior. It concerns a different Junos engineering issue IS-IS wide metrics traffic engineering and cost selection, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
Question 82
A provider routing design review considers this situation. On a provider Ethernet segment, an operator searches for a BDR field in Junos IS-IS output and concludes no resilience exists. A colleague proposes: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm. Which technical principle BEST supports that action? Select ONE best answer.
- IS-IS elects a DIS on a broadcast segment to originate pseudonode information; it has no OSPF-style separately elected backup designated router, and election behavior differs.
- BGP selects eligible routes according to an ordered decision process; provider-assigned local preference can override a shorter AS path and operational policy matters.
- IS-IS hello compatibility requires suitable circuit level, area relation for Level 1, supported MTU/parameters and authentication; physical link Up alone is insufficient.
- An L1 network may rely on attached/default routing toward L1/L2 routers; deliberate interlevel leaking or summarization can expose selected routes without making every area full Level 2.
Explanation
Correct Answer
A:The relevant Junos service-provider networking principle is: IS-IS elects a DIS on a broadcast segment to originate pseudonode information; it has no OSPF-style separately elected backup designated router, and election behavior differs. In the described provider-network case (On a provider Ethernet segment, an operator searches for a BDR field in Junos IS-IS output and concludes no resilience exists.), it supports the planned action: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
Incorrect Answers
B:This alternative proposes: BGP selects eligible routes according to an ordered decision process; provider-assigned local preference can override a shorter AS path and operational policy matters. It concerns a different Junos engineering issue BGP best-path attributes and local preference, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
C:This alternative proposes: IS-IS hello compatibility requires suitable circuit level, area relation for Level 1, supported MTU/parameters and authentication; physical link Up alone is insufficient. It concerns a different Junos engineering issue IS-IS adjacency NET and interface mismatch troubleshooting, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
D:This alternative proposes: An L1 network may rely on attached/default routing toward L1/L2 routers; deliberate interlevel leaking or summarization can expose selected routes without making every area full Level 2. It concerns a different Junos engineering issue IS-IS Level 2 to Level 1 route leaking and summaries, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
Question 83
A Juniper service-provider engineer needs decisive verification evidence for this situation. On a provider Ethernet segment, an operator searches for a BDR field in Junos IS-IS output and concludes no resilience exists. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.
- Compare show isis database, LSP sequence numbers, CSNP/PSNP exchange, interface errors and per-level adjacency status for the affected path.
- Inspect Ethernet segment configuration, ESI values, DF election or relevant designated-forwarder state, ES routes, BGP reachability and measured failover forwarding.
- Review show isis interface detail, LAN priority, circuit level, elected DIS, neighbor states and pseudonode LSP records.
- Compare NET area addresses, circuit levels, show isis adjacency detail, L1 versus L2 route tables and the attached bit on designated exits.
Explanation
Correct Answer
C:In the stated situation (On a provider Ethernet segment, an operator searches for a BDR field in Junos IS-IS output and concludes no resilience exists.), the intended acceptance outcome is: The expected DIS represents the shared LAN in the LSDB and routes converge when a controlled election change takes place.
Incorrect Answers
A:This alternative proposes: Compare show isis database, LSP sequence numbers, CSNP/PSNP exchange, interface errors and per-level adjacency status for the affected path. It concerns a different Junos engineering issue IS-IS link-state packet flooding and database consistency, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
B:This alternative proposes: Inspect Ethernet segment configuration, ESI values, DF election or relevant designated-forwarder state, ES routes, BGP reachability and measured failover forwarding. It concerns a different Junos engineering issue EVPN Ethernet segment multihoming and designated forwarder, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
D:This alternative proposes: Compare NET area addresses, circuit levels, show isis adjacency detail, L1 versus L2 route tables and the attached bit on designated exits. It concerns a different Junos engineering issue IS-IS level one level two hierarchy and area boundaries, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
Question 84
A service-provider acceptance team reviews the result of a provider-service change. On a provider Ethernet segment, an operator searches for a BDR field in Junos IS-IS output and concludes no resilience exists. The intended verification is: Review show isis interface detail, LAN priority, circuit level, elected DIS, neighbor states and pseudonode LSP records. Which outcome BEST demonstrates success? Select ONE best answer.
- The appropriate designated and backup routers maintain required adjacencies and exchange reachability across the shared Ethernet without unnecessary resets.
- Each subscriber region reaches its own internal endpoints and approved destinations through the selected L1/L2 border systems without losing its default path.
- Access routers learn only authorized leaked routes, continue using their correct area exit and do not create interlevel routing loops.
- The expected DIS represents the shared LAN in the LSDB and routes converge when a controlled election change takes place.
Explanation
Correct Answer
D:The verified success outcome is: The expected DIS represents the shared LAN in the LSDB and routes converge when a controlled election change takes place. Confirm this by: Review show isis interface detail, LAN priority, circuit level, elected DIS, neighbor states and pseudonode LSP records.
Incorrect Answers
A:This alternative proposes: The appropriate designated and backup routers maintain required adjacencies and exchange reachability across the shared Ethernet without unnecessary resets. It concerns a different Junos engineering issue OSPF designated router election on a multiaccess segment, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
B:That option concerns IS-IS level one level two hierarchy and area boundaries. The related controlled intervention is: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
C:That option concerns IS-IS Level 2 to Level 1 route leaking and summaries. The related controlled intervention is: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
Question 85
A Junos service-provider routing engineer investigates this service-provider network scenario. On a provider Ethernet segment, an operator searches for a BDR field in Junos IS-IS output and concludes no resilience exists. Which TWO complementary steps combine a suitable technical action and its direct verification? Select TWO answers.
- Compare show isis database, LSP sequence numbers, CSNP/PSNP exchange, interface errors and per-level adjacency status for the affected path.
- Verify address-family negotiation and route transport for IPv4 unicast, VPNv4, VPNv6 or EVPN separately rather than treating Established BGP TCP state as proof each family works.
- Review show isis interface detail, LAN priority, circuit level, elected DIS, neighbor states and pseudonode LSP records.
- Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
- Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
Explanation
Correct Answers
C:The direct discriminating observation is: Review show isis interface detail, LAN priority, circuit level, elected DIS, neighbor states and pseudonode LSP records. In the stated situation (On a provider Ethernet segment, an operator searches for a BDR field in Junos IS-IS output and concludes no resilience exists.), the intended acceptance outcome is: The expected DIS represents the shared LAN in the LSDB and routes converge when a controlled election change takes place.
D:The case-specific routing and services action is: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm. The governing Junos routing/service principle is: IS-IS elects a DIS on a broadcast segment to originate pseudonode information; it has no OSPF-style separately elected backup designated router, and election behavior differs. Verify the decision through: Review show isis interface detail, LAN priority, circuit level, elected DIS, neighbor states and pseudonode LSP records.
Incorrect Answers
A:This alternative proposes: Compare show isis database, LSP sequence numbers, CSNP/PSNP exchange, interface errors and per-level adjacency status for the affected path. It concerns a different Junos engineering issue IS-IS link-state packet flooding and database consistency, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election in the stated situation (On a provider Ethernet segment, an operator searches for a BDR field in Junos IS-IS output and concludes no resilience exists.). A better case-specific check is: Review show isis interface detail, LAN priority, circuit level, elected DIS, neighbor states and pseudonode LSP records.
B:This alternative proposes: Verify address-family negotiation and route transport for IPv4 unicast, VPNv4, VPNv6 or EVPN separately rather than treating Established BGP TCP state as proof each family works. It concerns a different Junos engineering issue Multiprotocol BGP family negotiations and VPN routes, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
E:This alternative proposes: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection. It concerns a different Junos engineering issue Site of Origin and OSPF sham-link loop control, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
Question 86
A Junos service-provider routing engineer investigates the following routing and service incident: During link repair, a newly added higher-priority IS-IS router becomes DIS and technicians confuse the normal pseudonode update with a data-plane attack. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.
- Restrict interlevel IS-IS route advertisements to the intended prefixes with controlled L1/L2 policy and verify return reachability.
- Verify IPv6 customer prefixes across a supported L3VPN by checking VPNv6 MP-BGP family, route targets and IPv6 customer forwarding independently of IPv4 VPNv4 behavior.
- Check whether the deployed IS-IS metric style and link costs support the provider's intended routing and traffic-engineering behavior.
- Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
Explanation
Correct Answer
D:The case-specific routing and services action is: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
Incorrect Answers
A:This alternative proposes: Restrict interlevel IS-IS route advertisements to the intended prefixes with controlled L1/L2 policy and verify return reachability. It concerns a different Junos engineering issue IS-IS Level 2 to Level 1 route leaking and summaries, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
B:This alternative proposes: Verify IPv6 customer prefixes across a supported L3VPN by checking VPNv6 MP-BGP family, route targets and IPv6 customer forwarding independently of IPv4 VPNv4 behavior. It concerns a different Junos engineering issue IPv6 Layer 3 VPN VPNv6 route families and forwarding, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
C:This alternative proposes: Check whether the deployed IS-IS metric style and link costs support the provider's intended routing and traffic-engineering behavior. It concerns a different Junos engineering issue IS-IS wide metrics traffic engineering and cost selection, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
Question 87
A provider routing design review considers this situation. During link repair, a newly added higher-priority IS-IS router becomes DIS and technicians confuse the normal pseudonode update with a data-plane attack. A colleague proposes: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm. Which technical principle BEST supports that action? Select ONE best answer.
- Level 1 routers know their local IS-IS area, Level 2 routers maintain interarea connectivity, and L1/L2 systems can provide area exits with suitable reachability and attached signaling.
- A BGP route can be accepted yet hidden or unusable when the advertised next hop cannot be resolved through an appropriate routing table or transport tunnel.
- IS-IS elects a DIS on a broadcast segment to originate pseudonode information; it has no OSPF-style separately elected backup designated router, and election behavior differs.
- IS-IS wide metrics support extended values and modern topology use cases, but cost selection depends on configured interface metrics and supported protocol behavior.
Explanation
Correct Answer
C:The relevant Junos service-provider networking principle is: IS-IS elects a DIS on a broadcast segment to originate pseudonode information; it has no OSPF-style separately elected backup designated router, and election behavior differs. In the described provider-network case (During link repair, a newly added higher-priority IS-IS router becomes DIS and technicians confuse the normal pseudonode update with a data-plane attack.), it supports the planned action: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
Incorrect Answers
A:This alternative proposes: Level 1 routers know their local IS-IS area, Level 2 routers maintain interarea connectivity, and L1/L2 systems can provide area exits with suitable reachability and attached signaling. It concerns a different Junos engineering issue IS-IS level one level two hierarchy and area boundaries, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
B:This alternative proposes: A BGP route can be accepted yet hidden or unusable when the advertised next hop cannot be resolved through an appropriate routing table or transport tunnel. It concerns a different Junos engineering issue BGP NEXT_HOP reachability and inet.3 recursion, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
D:This alternative proposes: IS-IS wide metrics support extended values and modern topology use cases, but cost selection depends on configured interface metrics and supported protocol behavior. It concerns a different Junos engineering issue IS-IS wide metrics traffic engineering and cost selection, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
Question 88
A Juniper service-provider engineer needs decisive verification evidence for this situation. During link repair, a newly added higher-priority IS-IS router becomes DIS and technicians confuse the normal pseudonode update with a data-plane attack. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.
- Inspect IS-IS metric configuration on both ends, extended TLV capability, show isis route, and SPF results before changing costs.
- Compare NET area addresses, circuit levels, show isis adjacency detail, L1 versus L2 route tables and the attached bit on designated exits.
- Check area IDs, ABR relationships, backbone LSA visibility, virtual-link state, and show ospf neighbor and database before adjusting policies.
- Review show isis interface detail, LAN priority, circuit level, elected DIS, neighbor states and pseudonode LSP records.
Explanation
Correct Answer
D:The direct discriminating observation is: Review show isis interface detail, LAN priority, circuit level, elected DIS, neighbor states and pseudonode LSP records. In the stated situation (During link repair, a newly added higher-priority IS-IS router becomes DIS and technicians confuse the normal pseudonode update with a data-plane attack.), the intended acceptance outcome is: The expected DIS represents the shared LAN in the LSDB and routes converge when a controlled election change takes place.
Incorrect Answers
A:This alternative proposes: Inspect IS-IS metric configuration on both ends, extended TLV capability, show isis route, and SPF results before changing costs. It concerns a different Junos engineering issue IS-IS wide metrics traffic engineering and cost selection, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
B:This alternative proposes: Compare NET area addresses, circuit levels, show isis adjacency detail, L1 versus L2 route tables and the attached bit on designated exits. It concerns a different Junos engineering issue IS-IS level one level two hierarchy and area boundaries, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
C:This alternative proposes: Check area IDs, ABR relationships, backbone LSA visibility, virtual-link state, and show ospf neighbor and database before adjusting policies. It concerns a different Junos engineering issue OSPF multi-area backbone connectivity and virtual-link limitations, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
Question 89
A service-provider acceptance team reviews the result of a provider-service change. During link repair, a newly added higher-priority IS-IS router becomes DIS and technicians confuse the normal pseudonode update with a data-plane attack. The intended verification is: Review show isis interface detail, LAN priority, circuit level, elected DIS, neighbor states and pseudonode LSP records. Which outcome BEST demonstrates success? Select ONE best answer.
- Neighbor state reaches Up at the expected level and routing recovers without exposing a different operator's area or changing every circuit.
- The expected DIS represents the shared LAN in the LSDB and routes converge when a controlled election change takes place.
- Neighbor databases converge on consistent current LSPs and the intended network prefixes resolve through matching shortest-path computations.
- Prefixes carry the intended tagged policy signal and any permitted local preference or propagation change is confirmed at the correct peer.
Explanation
Correct Answer
B:The verified success outcome is: The expected DIS represents the shared LAN in the LSDB and routes converge when a controlled election change takes place. Confirm this by: Review show isis interface detail, LAN priority, circuit level, elected DIS, neighbor states and pseudonode LSP records. The related controlled intervention is: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
Incorrect Answers
A:That option concerns IS-IS adjacency NET and interface mismatch troubleshooting. The related controlled intervention is: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
C:That option concerns IS-IS link-state packet flooding and database consistency. The related controlled intervention is: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
D:That option concerns BGP communities and selective transit routing policy. The related controlled intervention is: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
Question 90
A Junos routing design reviewer evaluates an unsafe shortcut in this network customer scenario. During link repair, a newly added higher-priority IS-IS router becomes DIS and technicians confuse the normal pseudonode update with a data-plane attack. Which assumption is MOST DIRECTLY dangerous or unsupported? Select ONE best answer.
- Assume a core link with more bandwidth automatically has the lowest IS-IS metric when no operator metric policy has been configured.
- Treat an IS-IS DIS as permanently paired with a mandatory BDR and declare the broadcast domain broken when a backup election is not shown.
- Advertise the same RP anycast address from two routers without configuring or verifying required RP-state coordination and call the design fully resilient.
- Expect two pure Level 1 routers in different IS-IS areas to exchange routes directly across the core without an eligible Level 2 path.
Explanation
Correct Answer
B:Apply instead: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
Incorrect Answers
A:This alternative proposes: Assume a core link with more bandwidth automatically has the lowest IS-IS metric when no operator metric policy has been configured. It concerns a different Junos engineering issue IS-IS wide metrics traffic engineering and cost selection, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
C:This alternative proposes: Advertise the same RP anycast address from two routers without configuring or verifying required RP-state coordination and call the design fully resilient. It concerns a different Junos engineering issue Anycast RP resilient multicast service and routing policy, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.
D:This alternative proposes: Expect two pure Level 1 routers in different IS-IS areas to exchange routes directly across the core without an eligible Level 2 path. It concerns a different Junos engineering issue IS-IS level one level two hierarchy and area boundaries, not the directly tested provider-network issue IS-IS DIS pseudonode and broadcast circuit election.