cert
cert-1
cert-2

Pass Cisco 500-220 Exam in First Attempt Guaranteed!

Get 100% Latest Exam Questions, Accurate & Verified Answers to Pass the Actual Exam!
30 Days Free Updates, Instant Download!

cert-5
cert-6
500-220 Exam - Verified By Experts
500-220 Premium File

500-220 Premium File

$69.99
$76.99
  • Premium File 85 Questions & Answers. Last Update: Nov 13, 2026

Whats Included:

  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
 
$76.99
$69.99
accept 13 downloads in the last 7 days
block-screenshots
Cisco 500-220 Practice Test 49

Question 480

A Cisco Meraki deployment engineer must choose a safe configuration decision and one validating observation. A campus moves employee and voice gateways onto a routing-capable MS but forgets to add a needed route to the MX. Which TWO steps together provide a targeted response with objective verification? Select TWO answers.

  1. Check SVI addressing, routing state, next hops and representative inter-VLAN traffic.
  2. Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning.
  3. Compare template binding state, site-specific subnet variables and the network configuration change history.
  4. Apply guest SSID access, splash and LAN-isolation settings that preserve required DHCP, DNS and permitted Internet services.
  5. Check the organization's licensing mode and the applicable Cisco Meraki model-specific guidance before interpreting a warning.

Explanation

Correct Answers

A:

The discriminating evidence is: Check SVI addressing, routing state, next hops and representative inter-VLAN traffic.

B:

The targeted next step is: Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning. The technical reason is: A routing-capable MS requires configured L3 interfaces and routes to forward between subnets; VLAN creation is not sufficient. A successful verification would use: Check SVI addressing, routing state, next hops and representative inter-VLAN traffic.

Incorrect Answers

C:

That evidence is relevant to the distinct Meraki subject of Configuration templates and network binding, not the specific MS switch routing interface and L3 reachability requirement.

D:

That action is relevant to the distinct Meraki subject of MR guest SSID splash and isolation settings, not the specific MS switch routing interface and L3 reachability requirement.

E:

That evidence is relevant to the distinct Meraki subject of Meraki subscription licensing versus historical per-device licensing, not the specific MS switch routing interface and L3 reachability requirement.

Question 481

A Cisco Meraki deployment engineer investigates this operational case: A branch adds VLAN 40 and sees local layer-2 traffic but no connectivity to VLAN 20 applications. What is the most appropriate FIRST action to address the stated requirement? Select ONE best answer.

  1. Set a switch access port to the required VLAN and use supported tagged trunk connections for multi-VLAN uplinks.
  2. Check device uplink and cloud reachability separately from local LAN forwarding before declaring a Meraki switch offline to users.
  3. Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning.
  4. Correlate a Meraki Dashboard alert with device event timestamps and a controlled client test before escalating a site outage.

Explanation

Correct Answer

C:

The targeted next step is: Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning.

Incorrect Answers

A:

That action is relevant to the distinct Meraki subject of MS access and trunk port VLAN assignment, not the specific MS switch routing interface and L3 reachability requirement. For this scenario, the proper response is: Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning. Verify it through: Check SVI addressing, routing state, next hops and representative inter-VLAN traffic.

B:

That action is relevant to the distinct Meraki subject of Dashboard cloud control plane versus local packet forwarding, not the specific MS switch routing interface and L3 reachability requirement.

D:

That action is relevant to the distinct Meraki subject of Dashboard alerts versus actual incident evidence, not the specific MS switch routing interface and L3 reachability requirement.

Question 482

A peer reviewer evaluates the following Meraki case. A branch adds VLAN 40 and sees local layer-2 traffic but no connectivity to VLAN 20 applications. The proposed action is: Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning. Which technical principle BEST supports this decision? Select ONE best answer.

  1. Camera recording and alerts are separate functions; a notification can fail despite accessible captured video or healthy camera connectivity.
  2. A routing-capable MS requires configured L3 interfaces and routes to forward between subnets; VLAN creation is not sufficient.
  3. An IDS alert, blocked attempt and confirmed endpoint compromise are different evidence levels; category or severity alone is not proof of infection.
  4. An 802.1X enabled switch port needs the correct supplicant and server exchange, distinct from default VLAN forwarding.

Explanation

Correct Answer

B:

A routing-capable MS requires configured L3 interfaces and routes to forward between subnets; VLAN creation is not sufficient. In this situation (A branch adds VLAN 40 and sees local layer-2 traffic but no connectivity to VLAN 20 applications.), it justifies the action: Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning.

Incorrect Answers

A:

That principle is relevant to the distinct Meraki subject of MV smart camera video availability and alert settings, not the specific MS switch routing interface and L3 reachability requirement.

C:

That principle is relevant to the distinct Meraki subject of Security Center incident classification from threat events, not the specific MS switch routing interface and L3 reachability requirement.

D:

That principle is relevant to the distinct Meraki subject of MS 802.1X access control and RADIUS, not the specific MS switch routing interface and L3 reachability requirement.

Question 483

A Meraki support engineer must distinguish facts from assumptions. A branch adds VLAN 40 and sees local layer-2 traffic but no connectivity to VLAN 20 applications. Which diagnostic observation MOST DIRECTLY verifies the problem or requirement? Select ONE best answer.

  1. Check SVI addressing, routing state, next hops and representative inter-VLAN traffic.
  2. Inspect MS port configuration, VLAN tags, native VLAN choices and the endpoint's resulting IP lease.
  3. Compare baseline application response measurements, configured thresholds and controlled warning events.
  4. Compare client event history, AP channel/utilization, RSSI trends and authentication records during the failure.

Explanation

Correct Answer

A:

The discriminating evidence is: Check SVI addressing, routing state, next hops and representative inter-VLAN traffic. Expected result: Two authorized VLANs communicate through the intended L3 boundary while others stay isolated.

Incorrect Answers

B:

That evidence is relevant to the distinct Meraki subject of MS access and trunk port VLAN assignment, not the specific MS switch routing interface and L3 reachability requirement. For this scenario, the proper response is: Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning. Verify it through: Check SVI addressing, routing state, next hops and representative inter-VLAN traffic.

C:

That evidence is relevant to the distinct Meraki subject of Meraki Insight application threshold and alert tuning, not the specific MS switch routing interface and L3 reachability requirement.

D:

That evidence is relevant to the distinct Meraki subject of MR wireless RF interference and roaming diagnosis, not the specific MS switch routing interface and L3 reachability requirement.

Question 484

An implementation lead needs a measurable acceptance criterion for a Meraki change. A branch adds VLAN 40 and sees local layer-2 traffic but no connectivity to VLAN 20 applications. The proposed validation is: Check SVI addressing, routing state, next hops and representative inter-VLAN traffic. Which result BEST demonstrates that the intended requirement is satisfied? Select ONE best answer.

  1. Voice stays intelligible while bulk traffic shares the link according to the approved policy.
  2. The design assigns wireless, switching, security, camera, endpoint and application monitoring tasks to suitable components.
  3. The network engineer can identify rising errors or utilization without confusing cumulative totals with instantaneous rates.
  4. Two authorized VLANs communicate through the intended L3 boundary while others stay isolated.

Explanation

Correct Answer

D:

The acceptance criterion is: Two authorized VLANs communicate through the intended L3 boundary while others stay isolated. Verify it using: Check SVI addressing, routing state, next hops and representative inter-VLAN traffic.

Incorrect Answers

A:

That outcome is relevant to the distinct Meraki subject of MS QoS trust and voice traffic classification, not the specific MS switch routing interface and L3 reachability requirement.

B:

That outcome is relevant to the distinct Meraki subject of Product family capabilities and integrated Dashboard view, not the specific MS switch routing interface and L3 reachability requirement.

C:

That outcome is relevant to the distinct Meraki subject of SNMP telemetry and counter interpretation, not the specific MS switch routing interface and L3 reachability requirement.

Question 485

A Meraki operations reviewer examines this case. A branch adds VLAN 40 and sees local layer-2 traffic but no connectivity to VLAN 20 applications. Which assumption is the MOST DIRECTLY relevant unsafe or technically wrong shortcut to reject here? Select ONE best answer.

  1. Disable all access controls because one unmanaged printer lacks a compatible 802.1X supplicant.
  2. Assume a newly shipped replacement serial must always receive a fresh unrelated paid license without checking RMA linkage.
  3. Assume an MS MAC address table alone routes between distinct IP subnets without L3 configuration.
  4. Bridge unauthenticated guests straight into the internal finance VLAN merely because the SSID has a splash page.

Explanation

Correct Answer

C:

It conflicts with the relevant behavior: A routing-capable MS requires configured L3 interfaces and routes to forward between subnets; VLAN creation is not sufficient.

Incorrect Answers

A:

That proposal is unsafe in its own context (the separate topic of MS 802.1X access control and RADIUS), but it is not the shortcut tied most directly to this incident. The case-specific fault to reject concerns MS switch routing interface and L3 reachability: Assume an MS MAC address table alone routes between distinct IP subnets without L3 configuration.

B:

That proposal is unsafe in its own context (the separate topic of Licensing entitlement after hardware replacement), but it is not the shortcut tied most directly to this incident. The case-specific fault to reject concerns MS switch routing interface and L3 reachability: Assume an MS MAC address table alone routes between distinct IP subnets without L3 configuration.

D:

That proposal is unsafe in its own context (the separate topic of MR guest SSID splash and isolation settings), but it is not the shortcut tied most directly to this incident. The case-specific fault to reject concerns MS switch routing interface and L3 reachability: Assume an MS MAC address table alone routes between distinct IP subnets without L3 configuration.

Question 486

A Cisco Meraki deployment engineer investigates this operational case: A desk phone and PC share one MS port while calls degrade during file copies over the uplink. What is the most appropriate FIRST action to address the stated requirement? Select ONE best answer.

  1. Design voice prioritization consistently on access ports, switches and WAN shaping instead of setting one isolated queue.
  2. Validate the device's management network DNS, gateway and permitted outbound cloud connectivity before changing user firewall rules.
  3. Configure appropriate MS port QoS trust and handling for known voice endpoints while measuring contention.
  4. Set a switch access port to the required VLAN and use supported tagged trunk connections for multi-VLAN uplinks.

Explanation

Correct Answer

C:

The targeted next step is: Configure appropriate MS port QoS trust and handling for known voice endpoints while measuring contention. The technical reason is: QoS classification and queue scheduling matter only at contention points, and policy must be consistent along the path.

Incorrect Answers

A:

That action is relevant to the distinct Meraki subject of End-to-end QoS trust and voice policy, not the specific MS QoS trust and voice traffic classification requirement.

B:

That action is relevant to the distinct Meraki subject of Meraki device check-in requirements and upstream firewall rules, not the specific MS QoS trust and voice traffic classification requirement.

D:

That action is relevant to the distinct Meraki subject of MS access and trunk port VLAN assignment, not the specific MS QoS trust and voice traffic classification requirement. For this scenario, the proper response is: Configure appropriate MS port QoS trust and handling for known voice endpoints while measuring contention.

Question 487

A peer reviewer evaluates the following Meraki case. A desk phone and PC share one MS port while calls degrade during file copies over the uplink. The proposed action is: Configure appropriate MS port QoS trust and handling for known voice endpoints while measuring contention. Which technical principle BEST supports this decision? Select ONE best answer.

  1. Port configuration cloning can accelerate standardized deployments, but VLAN, uplink and security context must still be validated.
  2. Dynamic routing relies on consistent interfaces, adjacency and advertisement policy; the presence of an MX does not imply automatic OSPF peering everywhere.
  3. An 802.1X enabled switch port needs the correct supplicant and server exchange, distinct from default VLAN forwarding.
  4. QoS classification and queue scheduling matter only at contention points, and policy must be consistent along the path.

Explanation

Correct Answer

D:

QoS classification and queue scheduling matter only at contention points, and policy must be consistent along the path. In this situation (A desk phone and PC share one MS port while calls degrade during file copies over the uplink.), it justifies the action: Configure appropriate MS port QoS trust and handling for known voice endpoints while measuring contention.

Incorrect Answers

A:

That principle is relevant to the distinct Meraki subject of MS configuration templates and switch port cloning, not the specific MS QoS trust and voice traffic classification requirement.

B:

That principle is relevant to the distinct Meraki subject of OSPF LAN exchange and MX routing design, not the specific MS QoS trust and voice traffic classification requirement.

C:

That principle is relevant to the distinct Meraki subject of MS 802.1X access control and RADIUS, not the specific MS QoS trust and voice traffic classification requirement.

Question 488

A Meraki support engineer must distinguish facts from assumptions. A desk phone and PC share one MS port while calls degrade during file copies over the uplink. Which diagnostic observation MOST DIRECTLY verifies the problem or requirement? Select ONE best answer.

  1. Inspect the configured collector, export transport, sampling context and observed flow keys for a controlled session.
  2. Review port classification, DSCP markings, counters and an actual call under controlled congestion.
  3. Check organization inventory, device serial assignment and the target network's product types before moving hardware.
  4. Inspect MS port configuration, VLAN tags, native VLAN choices and the endpoint's resulting IP lease.

Explanation

Correct Answer

B:

The discriminating evidence is: Review port classification, DSCP markings, counters and an actual call under controlled congestion. Expected result: Voice stays intelligible while bulk traffic shares the link according to the approved policy.

Incorrect Answers

A:

That evidence is relevant to the distinct Meraki subject of NetFlow export and traffic visibility limits, not the specific MS QoS trust and voice traffic classification requirement.

C:

That evidence is relevant to the distinct Meraki subject of Organization and network hierarchy in Dashboard, not the specific MS QoS trust and voice traffic classification requirement.

D:

That evidence is relevant to the distinct Meraki subject of MS access and trunk port VLAN assignment, not the specific MS QoS trust and voice traffic classification requirement.

Question 489

An implementation lead needs a measurable acceptance criterion for a Meraki change. A desk phone and PC share one MS port while calls degrade during file copies over the uplink. The proposed validation is: Review port classification, DSCP markings, counters and an actual call under controlled congestion. Which result BEST demonstrates that the intended requirement is satisfied? Select ONE best answer.

  1. The branch receives shared security settings while retaining its correct local VLAN and addressing requirements.
  2. The necessary prefix is routed in both directions and a controlled application connection works.
  3. Voice stays intelligible while bulk traffic shares the link according to the approved policy.
  4. A client reaches its intended subnet and no unauthorized VLAN is transported to an access port.

Explanation

Correct Answer

C:

The acceptance criterion is: Voice stays intelligible while bulk traffic shares the link according to the approved policy. Verify it using: Review port classification, DSCP markings, counters and an actual call under controlled congestion. The associated corrective action is: Configure appropriate MS port QoS trust and handling for known voice endpoints while measuring contention.

Incorrect Answers

A:

That outcome is relevant to the distinct Meraki subject of Configuration templates and network binding, not the specific MS QoS trust and voice traffic classification requirement.

B:

That outcome is relevant to the distinct Meraki subject of Layer three next-hop and return-route troubleshooting, not the specific MS QoS trust and voice traffic classification requirement.

D:

That outcome is relevant to the distinct Meraki subject of MS access and trunk port VLAN assignment, not the specific MS QoS trust and voice traffic classification requirement.

Question 490

A Cisco Meraki deployment engineer must choose a safe configuration decision and one validating observation. A desk phone and PC share one MS port while calls degrade during file copies over the uplink. Which TWO steps together provide a targeted response with objective verification? Select TWO answers.

  1. Review port classification, DSCP markings, counters and an actual call under controlled congestion.
  2. Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning.
  3. Configure appropriate MS port QoS trust and handling for known voice endpoints while measuring contention.
  4. Set a switch access port to the required VLAN and use supported tagged trunk connections for multi-VLAN uplinks.
  5. Review VPN status, peer paths, remote route presence and a matching inter-site traffic test.

Explanation

Correct Answers

A:

The discriminating evidence is: Review port classification, DSCP markings, counters and an actual call under controlled congestion.

C:

The targeted next step is: Configure appropriate MS port QoS trust and handling for known voice endpoints while measuring contention. The technical reason is: QoS classification and queue scheduling matter only at contention points, and policy must be consistent along the path. A successful verification would use: Review port classification, DSCP markings, counters and an actual call under controlled congestion.

Incorrect Answers

B:

That action is relevant to the distinct Meraki subject of MS switch routing interface and L3 reachability, not the specific MS QoS trust and voice traffic classification requirement.

D:

That action is relevant to the distinct Meraki subject of MS access and trunk port VLAN assignment, not the specific MS QoS trust and voice traffic classification requirement. For this scenario, the proper response is: Configure appropriate MS port QoS trust and handling for known voice endpoints while measuring contention. Verify it through: Review port classification, DSCP markings, counters and an actual call under controlled congestion.

E:

That evidence is relevant to the distinct Meraki subject of Auto VPN peer tunnel health and route advertisement, not the specific MS QoS trust and voice traffic classification requirement.

Cisco Meraki Solutions Specialist (500-220) Practice Tests