Cisco 500-220 Practice Test 48
Question 470
A Cisco Meraki deployment engineer must choose a safe configuration decision and one validating observation. A new printer is connected to an MS port assigned to the guest VLAN rather than the server VLAN. Which TWO steps together provide a targeted response with objective verification? Select TWO answers.
- Inspect MS port configuration, VLAN tags, native VLAN choices and the endpoint's resulting IP lease.
- Check peer state, accepted and advertised prefixes and next-hop reachability at the intended datacenter edge.
- Inspect the Site-to-site VPN topology, hub selection and route advertisements for the affected branch.
- Set a switch access port to the required VLAN and use supported tagged trunk connections for multi-VLAN uplinks.
- Compare spectrum survey, channel overlap, expected client count, airtime use and retries at peak occupancy.
Explanation
Correct Answers
A:The discriminating evidence is: Inspect MS port configuration, VLAN tags, native VLAN choices and the endpoint's resulting IP lease.
D:The targeted next step is: Set a switch access port to the required VLAN and use supported tagged trunk connections for multi-VLAN uplinks. The technical reason is: An access port normally carries one untagged client VLAN while a trunk can carry explicitly permitted tagged VLANs. A successful verification would use: Inspect MS port configuration, VLAN tags, native VLAN choices and the endpoint's resulting IP lease.
Incorrect Answers
B:That evidence is relevant to the distinct Meraki subject of BGP route exchange at VPN hub and datacenter, not the specific MS access and trunk port VLAN assignment requirement.
C:That evidence is relevant to the distinct Meraki subject of Auto VPN hub-and-spoke site reachability, not the specific MS access and trunk port VLAN assignment requirement. For this scenario, the proper response is: Set a switch access port to the required VLAN and use supported tagged trunk connections for multi-VLAN uplinks. Verify it through: Inspect MS port configuration, VLAN tags, native VLAN choices and the endpoint's resulting IP lease.
E:That evidence is relevant to the distinct Meraki subject of High-density RF channel and AP count planning, not the specific MS access and trunk port VLAN assignment requirement.
Question 471
A Cisco Meraki deployment engineer investigates this operational case: An MX/MS interconnect carries several VLANs but the required camera VLAN is missing from the trunk's allowed list. What is the most appropriate FIRST action to address the stated requirement? Select ONE best answer.
- Use supported action batching or templates for repetitive network changes while monitoring per-action validation results.
- Set a switch access port to the required VLAN and use supported tagged trunk connections for multi-VLAN uplinks.
- Configure supported MS port access policies with a reachable RADIUS service and documented noncompliant-device handling.
- Define SD-WAN performance classes from measured application tolerance and available WAN path behavior before configuring traffic preferences.
Explanation
Correct Answer
B:The targeted next step is: Set a switch access port to the required VLAN and use supported tagged trunk connections for multi-VLAN uplinks.
Incorrect Answers
A:That action is relevant to the distinct Meraki subject of Action batches and template-based API efficiency, not the specific MS access and trunk port VLAN assignment requirement.
C:That action is relevant to the distinct Meraki subject of MS 802.1X access control and RADIUS, not the specific MS access and trunk port VLAN assignment requirement. For this scenario, the proper response is: Set a switch access port to the required VLAN and use supported tagged trunk connections for multi-VLAN uplinks. Verify it through: Inspect MS port configuration, VLAN tags, native VLAN choices and the endpoint's resulting IP lease.
D:That action is relevant to the distinct Meraki subject of Performance-class loss latency and jitter thresholds, not the specific MS access and trunk port VLAN assignment requirement.
Question 472
A peer reviewer evaluates the following Meraki case. An MX/MS interconnect carries several VLANs but the required camera VLAN is missing from the trunk's allowed list. The proposed action is: Set a switch access port to the required VLAN and use supported tagged trunk connections for multi-VLAN uplinks. Which technical principle BEST supports this decision? Select ONE best answer.
- A working overlay tunnel still needs compatible cloud-side routing for replies; asymmetric routing can break stateful services.
- Rogue or interfering AP observations require classification; an external neighboring AP is not automatically malicious corporate infrastructure.
- QoS classification and queue scheduling matter only at contention points, and policy must be consistent along the path.
- An access port normally carries one untagged client VLAN while a trunk can carry explicitly permitted tagged VLANs.
Explanation
Correct Answer
D:An access port normally carries one untagged client VLAN while a trunk can carry explicitly permitted tagged VLANs. In this situation (An MX/MS interconnect carries several VLANs but the required camera VLAN is missing from the trunk's allowed list.), it justifies the action: Set a switch access port to the required VLAN and use supported tagged trunk connections for multi-VLAN uplinks.
Incorrect Answers
A:That principle is relevant to the distinct Meraki subject of vMX traffic symmetry and cloud return routing, not the specific MS access and trunk port VLAN assignment requirement.
B:That principle is relevant to the distinct Meraki subject of MR Air Marshal threat and rogue SSID monitoring, not the specific MS access and trunk port VLAN assignment requirement. For this scenario, the proper response is: Set a switch access port to the required VLAN and use supported tagged trunk connections for multi-VLAN uplinks. Verify it through: Inspect MS port configuration, VLAN tags, native VLAN choices and the endpoint's resulting IP lease.
C:That principle is relevant to the distinct Meraki subject of MS QoS trust and voice traffic classification, not the specific MS access and trunk port VLAN assignment requirement.
Question 473
A Meraki support engineer must distinguish facts from assumptions. An MX/MS interconnect carries several VLANs but the required camera VLAN is missing from the trunk's allowed list. Which diagnostic observation MOST DIRECTLY verifies the problem or requirement? Select ONE best answer.
- Inspect MS port configuration, VLAN tags, native VLAN choices and the endpoint's resulting IP lease.
- Review event action, source/destination, signature or category and corroborating endpoint logs.
- Correlate interface health, performance-class violations and observed traffic transition during controlled impairment.
- Compare source and destination port roles, VLANs, PoE, labels and actual endpoint connectivity.
Explanation
Correct Answer
A:The discriminating evidence is: Inspect MS port configuration, VLAN tags, native VLAN choices and the endpoint's resulting IP lease. Expected result: A client reaches its intended subnet and no unauthorized VLAN is transported to an access port.
Incorrect Answers
B:That evidence is relevant to the distinct Meraki subject of Security Center incident classification from threat events, not the specific MS access and trunk port VLAN assignment requirement.
C:That evidence is relevant to the distinct Meraki subject of Brownout versus hard WAN link-down detection, not the specific MS access and trunk port VLAN assignment requirement.
D:That evidence is relevant to the distinct Meraki subject of MS configuration templates and switch port cloning, not the specific MS access and trunk port VLAN assignment requirement. For this scenario, the proper response is: Set a switch access port to the required VLAN and use supported tagged trunk connections for multi-VLAN uplinks. Verify it through: Inspect MS port configuration, VLAN tags, native VLAN choices and the endpoint's resulting IP lease.
Question 474
An implementation lead needs a measurable acceptance criterion for a Meraki change. An MX/MS interconnect carries several VLANs but the required camera VLAN is missing from the trunk's allowed list. The proposed validation is: Inspect MS port configuration, VLAN tags, native VLAN choices and the endpoint's resulting IP lease. Which result BEST demonstrates that the intended requirement is satisfied? Select ONE best answer.
- Required video evidence remains accessible and alerts fire only for the intended conditions.
- A client reaches its intended subnet and no unauthorized VLAN is transported to an access port.
- Voice stays intelligible while bulk traffic shares the link according to the approved policy.
- The on-premises branch reaches the approved private cloud service through a valid end-to-end route.
Explanation
Correct Answer
B:The acceptance criterion is: A client reaches its intended subnet and no unauthorized VLAN is transported to an access port. Verify it using: Inspect MS port configuration, VLAN tags, native VLAN choices and the endpoint's resulting IP lease. The associated corrective action is: Set a switch access port to the required VLAN and use supported tagged trunk connections for multi-VLAN uplinks.
Incorrect Answers
A:That outcome is relevant to the distinct Meraki subject of MV smart camera video availability and alert settings, not the specific MS access and trunk port VLAN assignment requirement.
C:That outcome is relevant to the distinct Meraki subject of MS QoS trust and voice traffic classification, not the specific MS access and trunk port VLAN assignment requirement.
D:That outcome is relevant to the distinct Meraki subject of vMX private cloud connectivity and deployment mode, not the specific MS access and trunk port VLAN assignment requirement.
Question 475
A Meraki operations reviewer examines this case. An MX/MS interconnect carries several VLANs but the required camera VLAN is missing from the trunk's allowed list. Which assumption is the MOST DIRECTLY relevant unsafe or technically wrong shortcut to reject here? Select ONE best answer.
- Reset every organization's Auto VPN tunnel whenever one local application fails.
- Assume BGP automatically advertises all private networks from any device plugged into the VPN hub.
- Set a user-facing port to an unrestricted trunk and expect VLAN separation to become stronger automatically.
- Clone an uplink trunk to every end-user access port without confirming their role.
Explanation
Correct Answer
C:It conflicts with the relevant behavior: An access port normally carries one untagged client VLAN while a trunk can carry explicitly permitted tagged VLANs.
Incorrect Answers
A:That proposal is unsafe in its own context (the separate topic of Auto VPN peer tunnel health and route advertisement), but it is not the shortcut tied most directly to this incident. The case-specific fault to reject concerns MS access and trunk port VLAN assignment: Set a user-facing port to an unrestricted trunk and expect VLAN separation to become stronger automatically.
B:That proposal is unsafe in its own context (the separate topic of BGP route exchange at VPN hub and datacenter), but it is not the shortcut tied most directly to this incident. The case-specific fault to reject concerns MS access and trunk port VLAN assignment: Set a user-facing port to an unrestricted trunk and expect VLAN separation to become stronger automatically.
D:That proposal is unsafe in its own context (the separate topic of MS configuration templates and switch port cloning), but it is not the shortcut tied most directly to this incident. The case-specific fault to reject concerns MS access and trunk port VLAN assignment: Set a user-facing port to an unrestricted trunk and expect VLAN separation to become stronger automatically.
Question 476
A Cisco Meraki deployment engineer investigates this operational case: A campus moves employee and voice gateways onto a routing-capable MS but forgets to add a needed route to the MX. What is the most appropriate FIRST action to address the stated requirement? Select ONE best answer.
- Set a switch access port to the required VLAN and use supported tagged trunk connections for multi-VLAN uplinks.
- Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning.
- Select supervised or device-owner enrollment only for appropriate corporate devices and define a lighter approved BYOD path.
- Define a guest-authorization and isolation path that supports Internet access without access to staff LAN services.
Explanation
Correct Answer
B:The targeted next step is: Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning. The technical reason is: A routing-capable MS requires configured L3 interfaces and routes to forward between subnets; VLAN creation is not sufficient.
Incorrect Answers
A:That action is relevant to the distinct Meraki subject of MS access and trunk port VLAN assignment, not the specific MS switch routing interface and L3 reachability requirement. For this scenario, the proper response is: Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning.
C:That action is relevant to the distinct Meraki subject of Systems Manager managed enrollment versus BYOD privacy, not the specific MS switch routing interface and L3 reachability requirement.
D:That action is relevant to the distinct Meraki subject of Guest Wi-Fi captive portal and traffic isolation, not the specific MS switch routing interface and L3 reachability requirement.
Question 477
A peer reviewer evaluates the following Meraki case. A campus moves employee and voice gateways onto a routing-capable MS but forgets to add a needed route to the MX. The proposed action is: Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning. Which technical principle BEST supports this decision? Select ONE best answer.
- Port configuration cloning can accelerate standardized deployments, but VLAN, uplink and security context must still be validated.
- A routing-capable MS requires configured L3 interfaces and routes to forward between subnets; VLAN creation is not sufficient.
- A wireless client can associate at the radio level yet fail access because RADIUS, certificate or VLAN policy rejects it.
- Managed enrollment status enables device-policy functions only where the platform and ownership mode support them.
Explanation
Correct Answer
B:A routing-capable MS requires configured L3 interfaces and routes to forward between subnets; VLAN creation is not sufficient. In this situation (A campus moves employee and voice gateways onto a routing-capable MS but forgets to add a needed route to the MX.), it justifies the action: Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning.
Incorrect Answers
A:That principle is relevant to the distinct Meraki subject of MS configuration templates and switch port cloning, not the specific MS switch routing interface and L3 reachability requirement.
C:That principle is relevant to the distinct Meraki subject of MR authentication and RADIUS reject troubleshooting, not the specific MS switch routing interface and L3 reachability requirement.
D:That principle is relevant to the distinct Meraki subject of Systems Manager MDM enrollment and compliance profiles, not the specific MS switch routing interface and L3 reachability requirement.
Question 478
A Meraki support engineer must distinguish facts from assumptions. A campus moves employee and voice gateways onto a routing-capable MS but forgets to add a needed route to the MX. Which diagnostic observation MOST DIRECTLY verifies the problem or requirement? Select ONE best answer.
- Inspect returned Link next-page information, accumulated serial IDs and a Dashboard inventory comparison.
- Audit network role assignments and test event viewing separately from actual change permissions.
- Check SVI addressing, routing state, next hops and representative inter-VLAN traffic.
- Inspect MS port configuration, VLAN tags, native VLAN choices and the endpoint's resulting IP lease.
Explanation
Correct Answer
C:The discriminating evidence is: Check SVI addressing, routing state, next hops and representative inter-VLAN traffic. Expected result: Two authorized VLANs communicate through the intended L3 boundary while others stay isolated.
Incorrect Answers
A:That evidence is relevant to the distinct Meraki subject of API pagination and complete inventory reconciliation, not the specific MS switch routing interface and L3 reachability requirement.
B:That evidence is relevant to the distinct Meraki subject of Network-level privileges and separation of duties, not the specific MS switch routing interface and L3 reachability requirement.
D:That evidence is relevant to the distinct Meraki subject of MS access and trunk port VLAN assignment, not the specific MS switch routing interface and L3 reachability requirement. For this scenario, the proper response is: Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning.
Question 479
An implementation lead needs a measurable acceptance criterion for a Meraki change. A campus moves employee and voice gateways onto a routing-capable MS but forgets to add a needed route to the MX. The proposed validation is: Check SVI addressing, routing state, next hops and representative inter-VLAN traffic. Which result BEST demonstrates that the intended requirement is satisfied? Select ONE best answer.
- New access ports match the approved role while exceptional trunk and security settings remain correct.
- Clients preserve approved services after the designated active appliance fails, subject to expected reconvergence.
- Real-time audio meets target quality while bulk file transfers are correctly deprioritized when links saturate.
- Two authorized VLANs communicate through the intended L3 boundary while others stay isolated.
Explanation
Correct Answer
D:The acceptance criterion is: Two authorized VLANs communicate through the intended L3 boundary while others stay isolated. Verify it using: Check SVI addressing, routing state, next hops and representative inter-VLAN traffic. The associated corrective action is: Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning.
Incorrect Answers
A:That outcome is relevant to the distinct Meraki subject of MS configuration templates and switch port cloning, not the specific MS switch routing interface and L3 reachability requirement.
B:That outcome is relevant to the distinct Meraki subject of MX high availability warm spare and uplink failover, not the specific MS switch routing interface and L3 reachability requirement.
C:That outcome is relevant to the distinct Meraki subject of End-to-end QoS trust and voice policy, not the specific MS switch routing interface and L3 reachability requirement.
Question 480
A Cisco Meraki deployment engineer must choose a safe configuration decision and one validating observation. A campus moves employee and voice gateways onto a routing-capable MS but forgets to add a needed route to the MX. Which TWO steps together provide a targeted response with objective verification? Select TWO answers.
- Check SVI addressing, routing state, next hops and representative inter-VLAN traffic.
- Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning.
- Compare template binding state, site-specific subnet variables and the network configuration change history.
- Apply guest SSID access, splash and LAN-isolation settings that preserve required DHCP, DNS and permitted Internet services.
- Check the organization's licensing mode and the applicable Cisco Meraki model-specific guidance before interpreting a warning.
Explanation
Correct Answers
A:The discriminating evidence is: Check SVI addressing, routing state, next hops and representative inter-VLAN traffic.
B:The targeted next step is: Create and validate supported MS L3 interfaces for a routed distribution role rather than relying on Layer-2 MAC learning. The technical reason is: A routing-capable MS requires configured L3 interfaces and routes to forward between subnets; VLAN creation is not sufficient. A successful verification would use: Check SVI addressing, routing state, next hops and representative inter-VLAN traffic.
Incorrect Answers
C:That evidence is relevant to the distinct Meraki subject of Configuration templates and network binding, not the specific MS switch routing interface and L3 reachability requirement.
D:That action is relevant to the distinct Meraki subject of MR guest SSID splash and isolation settings, not the specific MS switch routing interface and L3 reachability requirement.
E:That evidence is relevant to the distinct Meraki subject of Meraki subscription licensing versus historical per-device licensing, not the specific MS switch routing interface and L3 reachability requirement.