Cisco 350-601 Practice Test 76
Question 750
A SAN expansion connects two fabric switches but one side remains in a server-facing F-port mode. The observed failure is: mismatched port roles can prevent device logins or inter-switch fabric formation. Which recovery action addresses the underlying technical fault?
- The controlled remediation is to assign an L3 BGP peer instead of choosing FC port mode.
- The controlled remediation is to correct interface roles and verify FLOGI or inter-switch login according to the link purpose.
- The controlled remediation is to set every FC interface to an Ethernet access port.
- The controlled remediation is to assume any physical link light means FC port roles are compatible.
Explanation
Correct Answer
B:This addresses the observable fault while preserving a check of the expected result. Validate against interface operational FC port mode, neighbor type, FLOGI and E-port initialization status.
Incorrect Answers
A:Assign an L3 BGP peer instead of choosing FC port mode. This would not reliably restore service after the stated fault. Mismatched port roles can prevent device logins or inter-switch fabric formation. The controlled recovery is to correct interface roles and verify FLOGI or inter-switch login according to the link purpose.
C:Set every FC interface to an Ethernet access port. This would not reliably restore service after the stated fault. Mismatched port roles can prevent device logins or inter-switch fabric formation. The controlled recovery is to correct interface roles and verify FLOGI or inter-switch login according to the link purpose.
D:Assume any physical link light means FC port roles are compatible. This would not reliably restore service after the stated fault. Mismatched port roles can prevent device logins or inter-switch fabric formation. The controlled recovery is to correct interface roles and verify FLOGI or inter-switch login according to the link purpose.
Question 751
An extended FC link runs at low throughput with increasing credit starvation despite no physical errors. Which next step should the data center engineer select?
- Disable all FC flow control credits to allow unlimited transmission.
- Reduce zoning security to increase propagation speed.
- Check and size FC buffer-to-buffer credits appropriately for the supported long-distance port.
- Change an IP gateway address to add buffer credits to an FC ISL.
Explanation
Correct Answer
C:This directly addresses buffer-to-buffer credit starvation because Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits. Confirm the change against bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput.
Incorrect Answers
A:Insufficient credits can throttle a clean FC link even when optical errors are absent. The relevant correction is to check and size FC buffer-to-buffer credits appropriately for the supported long-distance port.
B:Reduce zoning security to increase propagation speed. The proposed change targets the wrong mechanism or lacks essential validation. Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits. Relevant evidence is bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput.
D:Insufficient credits can throttle a clean FC link even when optical errors are absent. The appropriate action remains to check and size FC buffer-to-buffer credits appropriately for the supported long-distance port.
Question 752
An extended FC link runs at low throughput with increasing credit starvation despite no physical errors. Which diagnostic record would most strongly confirm the result?
- An Ethernet ping that does not test the required SAN session or VSAN.
- A copied zoneset name without its active effective members.
- A green physical FC link light without fabric login, zoning or I/O evidence.
- BB-credit counters, zero-credit intervals, distance and line rate, and frame throughput.
Explanation
Correct Answer
D:These observations test the actual buffer-to-buffer credit starvation mechanism rather than a superficial management status. Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits.
Incorrect Answers
A:An Ethernet ping that does not test the required SAN session or VSAN. This information cannot independently verify buffer-to-buffer credit starvation. The decisive records instead include bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput. Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits.
B:A copied zoneset name without its active effective members. This information cannot independently verify buffer-to-buffer credit starvation. The decisive records instead include bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput. Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits.
C:A green physical FC link light without fabric login, zoning or I/O evidence. This information cannot independently verify buffer-to-buffer credit starvation. The decisive records instead include bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput. Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits.
Question 753
An extended FC link runs at low throughput with increasing credit starvation despite no physical errors. Which platform concept should guide the engineer’s assessment?
- Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits.
- Fibre Channel name service entries are identical to host multipath device state.
- A lit Fibre Channel link proves end-to-end LUN visibility and authorized I/O.
- WWPN zoning and IP access lists are interchangeable security primitives.
Explanation
Correct Answer
A:This explains why the most appropriate response is to check and size FC buffer-to-buffer credits appropriately for the supported long-distance port. Validation depends on bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput.
Incorrect Answers
B:Fibre Channel name service entries are identical to host multipath device state. This is an incorrect generalization for buffer-to-buffer credit starvation. The applicable technical behavior is that Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits. The operator should verify bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput.
C:A lit Fibre Channel link proves end-to-end LUN visibility and authorized I/O. This is an incorrect generalization for buffer-to-buffer credit starvation. The applicable technical behavior is that Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits. The operator should verify bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput.
D:WWPN zoning and IP access lists are interchangeable security primitives. This is an incorrect generalization for buffer-to-buffer credit starvation. The applicable technical behavior is that Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits. The operator should verify bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput.
Question 754
An extended FC link runs at low throughput with increasing credit starvation despite no physical errors. Assume an engineer instead chooses to disable all FC flow control credits to allow unlimited transmission. Which root-cause observation follows from that incorrect change?
- Examining FCNS entries automatically removes the authorized zoning policy.
- Insufficient credits can throttle a clean FC link even when optical errors are absent.
- The SAN failed because operators retained correct WWPN identity records.
- The sole error was using a verified SAN maintenance window for a risky operation.
Explanation
Correct Answer
B:Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits. That is the direct consequence of choosing the misleading shortcut.
Incorrect Answers
A:This does not explain the actual buffer-to-buffer credit starvation defect after the shortcut. The meaningful failure is that insufficient credits can throttle a clean FC link even when optical errors are absent.
C:This does not explain the actual buffer-to-buffer credit starvation defect after the shortcut. The relevant evidence is bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput.
D:This does not explain the actual buffer-to-buffer credit starvation defect after the shortcut. The sole error was using a verified SAN maintenance window for a risky operation.
Question 755
An extended FC link runs at low throughput with increasing credit starvation despite no physical errors. The observed failure is: insufficient credits can throttle a clean FC link even when optical errors are absent. Which recovery action addresses the underlying technical fault?
- Reduce zoning security to increase propagation speed.
- Change an IP gateway address to add buffer credits to an FC ISL.
- Allocate supported credits and confirm credit recovery and throughput under load.
- Disable all FC flow control credits to allow unlimited transmission.
Explanation
Correct Answer
C:Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits. This addresses the observable fault while preserving a check of the expected result.
Incorrect Answers
A:Reduce zoning security to increase propagation speed. This would not reliably restore service after the stated fault. Insufficient credits can throttle a clean FC link even when optical errors are absent. The controlled recovery is to allocate supported credits and confirm credit recovery and throughput under load.
B:Change an IP gateway address to add buffer credits to an FC ISL. This would not reliably restore service after the stated fault. Insufficient credits can throttle a clean FC link even when optical errors are absent. The controlled recovery is to allocate supported credits and confirm credit recovery and throughput under load.
D:Disable all FC flow control credits to allow unlimited transmission. This would not reliably restore service after the stated fault. Insufficient credits can throttle a clean FC link even when optical errors are absent. The controlled recovery is to allocate supported credits and confirm credit recovery and throughput under load.
Question 756
An MDS ISL traverses a long-distance optical circuit where the default buffer-to-buffer credit budget cannot fill the bandwidth-delay product. What is the BEST supported implementation or corrective action?
- On this affected device, the engineer should reduce zoning security to increase propagation speed.
- On this affected device, the engineer should change an IP gateway address to add buffer credits to an FC ISL.
- On this affected device, the engineer should disable all FC flow control credits to allow unlimited transmission.
- On this affected device, the engineer should check and size FC buffer-to-buffer credits appropriately for the supported long-distance port.
Explanation
Correct Answer
D:This directly addresses buffer-to-buffer credit starvation because Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits.
Incorrect Answers
A:Reduce zoning security to increase propagation speed. The proposed change targets the wrong mechanism or lacks essential validation. Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits. Relevant evidence is bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput.
B:Insufficient credits can throttle a clean FC link even when optical errors are absent. In the given case, an MDS ISL traverses a long-distance optical circuit where the default buffer-to-buffer credit budget cannot fill the bandwidth-delay product.
C:Insufficient credits can throttle a clean FC link even when optical errors are absent. Disable all FC flow control credits to allow unlimited transmission.
Question 757
An MDS ISL traverses a long-distance optical circuit where the default buffer-to-buffer credit budget cannot fill the bandwidth-delay product. Which evidence BEST verifies the intended technical behavior?
- For this deployment, examine bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput.
- For this deployment, examine a historical FC topology drawing with no current WWPN or port state.
- For this deployment, examine an Ethernet ping that does not test the required SAN session or VSAN.
- For this deployment, examine a copied zoneset name without its active effective members.
Explanation
Correct Answer
A:These observations test the actual buffer-to-buffer credit starvation mechanism rather than a superficial management status. They should be checked after check and size FC buffer-to-buffer credits appropriately for the supported long-distance port.
Incorrect Answers
B:A historical FC topology drawing with no current WWPN or port state. This information cannot independently verify buffer-to-buffer credit starvation. The decisive records instead include bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput. Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits.
C:An Ethernet ping that does not test the required SAN session or VSAN. This information cannot independently verify buffer-to-buffer credit starvation. The decisive records instead include bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput. Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits.
D:A copied zoneset name without its active effective members. This information cannot independently verify buffer-to-buffer credit starvation. The decisive records instead include bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput. Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits.
Question 758
An MDS ISL traverses a long-distance optical circuit where the default buffer-to-buffer credit budget cannot fill the bandwidth-delay product. Which principle BEST explains why the recommended solution is appropriate?
- For this condition, the applicable principle is that wWPN zoning and IP access lists are interchangeable security primitives.
- For this condition, the applicable principle is that Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits.
- For this condition, the applicable principle is that Fibre Channel name service entries are identical to host multipath device state.
- For this condition, the applicable principle is that an unused VSAN number can replace an active zoning or port security rule.
Explanation
Correct Answer
B:This explains why the most appropriate response is to check and size FC buffer-to-buffer credits appropriately for the supported long-distance port.
Incorrect Answers
A:WWPN zoning and IP access lists are interchangeable security primitives. This is an incorrect generalization for buffer-to-buffer credit starvation. The applicable technical behavior is that Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits. The operator should verify bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput.
C:Fibre Channel name service entries are identical to host multipath device state. This is an incorrect generalization for buffer-to-buffer credit starvation. The applicable technical behavior is that Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits. The operator should verify bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput.
D:An unused VSAN number can replace an active zoning or port security rule. This is an incorrect generalization for buffer-to-buffer credit starvation. The applicable technical behavior is that Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits. The operator should verify bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput.
Question 759
An MDS ISL traverses a long-distance optical circuit where the default buffer-to-buffer credit budget cannot fill the bandwidth-delay product. Assume an engineer instead chooses to disable all FC flow control credits to allow unlimited transmission. What is the MOST significant failure introduced by that shortcut?
- The resulting defect is that the sole error was using a verified SAN maintenance window for a risky operation.
- The resulting defect is that inspecting credit counters prevents FC frames from forwarding.
- The resulting defect is that insufficient credits can throttle a clean FC link even when optical errors are absent.
- The resulting defect is that the SAN failed because operators retained correct WWPN identity records.
Explanation
Correct Answer
C:Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits. The proper corrective action is to check and size FC buffer-to-buffer credits appropriately for the supported long-distance port.
Incorrect Answers
A:This does not explain the actual buffer-to-buffer credit starvation defect after the shortcut. In the given case, an MDS ISL traverses a long-distance optical circuit where the default buffer-to-buffer credit budget cannot fill the bandwidth-delay product.
B:The meaningful failure is that insufficient credits can throttle a clean FC link even when optical errors are absent.
D:This does not explain the actual buffer-to-buffer credit starvation defect after the shortcut. The SAN failed because operators retained correct WWPN identity records.
Question 760
An MDS ISL traverses a long-distance optical circuit where the default buffer-to-buffer credit budget cannot fill the bandwidth-delay product. The observed failure is: insufficient credits can throttle a clean FC link even when optical errors are absent. What is the BEST controlled recovery once this failure is recognized?
- The controlled remediation is to change an IP gateway address to add buffer credits to an FC ISL.
- The controlled remediation is to disable all FC flow control credits to allow unlimited transmission.
- The controlled remediation is to reduce zoning security to increase propagation speed.
- The controlled remediation is to allocate supported credits and confirm credit recovery and throughput under load.
Explanation
Correct Answer
D:Fibre Channel uses buffer-to-buffer credits for hop flow control, so long propagation delay can require more credits. Validate against bB-credit counters, zero-credit intervals, distance and line rate, and frame throughput.
Incorrect Answers
A:Change an IP gateway address to add buffer credits to an FC ISL. This would not reliably restore service after the stated fault. Insufficient credits can throttle a clean FC link even when optical errors are absent. The controlled recovery is to allocate supported credits and confirm credit recovery and throughput under load.
B:Disable all FC flow control credits to allow unlimited transmission. This would not reliably restore service after the stated fault. Insufficient credits can throttle a clean FC link even when optical errors are absent. The controlled recovery is to allocate supported credits and confirm credit recovery and throughput under load.
C:Reduce zoning security to increase propagation speed. This would not reliably restore service after the stated fault. Insufficient credits can throttle a clean FC link even when optical errors are absent. The controlled recovery is to allocate supported credits and confirm credit recovery and throughput under load.