Cisco 350-601 Practice Test 7
Question 60
A VXLAN fabric can see a remote EVPN route in BGP, yet it is not installed into the intended tenant routing table. The observed failure is: a route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. What should the engineer do to recover and validate the service?
- The controlled remediation is to advertise one universal route target to all tenants without an isolation review.
- The controlled remediation is to disable every VRF on the switch to make routes globally visible.
- The controlled remediation is to change only an NTP server address and expect VRF import.
- The controlled remediation is to repair the narrowly scoped RT mapping and verify the expected tenant routes and isolation.
Explanation
Correct Answer
D:This addresses the observable fault while preserving a check of the expected result. Validate against EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.
Incorrect Answers
A:Advertise one universal route target to all tenants without an isolation review. This would not reliably restore service after the stated fault. A route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. The controlled recovery is to repair the narrowly scoped RT mapping and verify the expected tenant routes and isolation.
B:Disable every VRF on the switch to make routes globally visible. This would not reliably restore service after the stated fault. A route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. The controlled recovery is to repair the narrowly scoped RT mapping and verify the expected tenant routes and isolation.
C:Change only an NTP server address and expect VRF import. This would not reliably restore service after the stated fault. A route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. The controlled recovery is to repair the narrowly scoped RT mapping and verify the expected tenant routes and isolation.
Question 61
Leaf switches are BGP peers of a pair of route reflectors, but prefixes received from one leaf are not reflected to another. Which operator action best meets this technical requirement?
- Validate route-reflector client configuration and address-family policy on the designated reflectors.
- Force a full iBGP mesh by deleting the reflectors without a design review.
- Clear the entire underlay OSPF process whenever one EVPN route is missing.
- Turn off route advertisement on all leaves as a permanent workaround.
Explanation
Correct Answer
A:This directly addresses BGP route-reflector client policy because route reflectors can distribute iBGP routes between clients while preserving control-plane policies. Confirm the change against BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
Incorrect Answers
B:An up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned. The relevant correction is to validate route-reflector client configuration and address-family policy on the designated reflectors.
C:Clear the entire underlay OSPF process whenever one EVPN route is missing. The proposed change targets the wrong mechanism or lacks essential validation. Route reflectors can distribute iBGP routes between clients while preserving control-plane policies. Relevant evidence is BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
D:An up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned. The appropriate action remains to validate route-reflector client configuration and address-family policy on the designated reflectors.
Question 62
Leaf switches are BGP peers of a pair of route reflectors, but prefixes received from one leaf are not reflected to another. Which collection of observations most directly tests the suspected cause?
- One successful ping to an unrelated management address.
- BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
- An interface description without the effective peer or VXLAN policy.
- A healthy optical light without checking protocol neighbors or forwarding entries.
Explanation
Correct Answer
B:These observations test the actual BGP route-reflector client policy mechanism rather than a superficial management status. Route reflectors can distribute iBGP routes between clients while preserving control-plane policies.
Incorrect Answers
A:This information cannot independently verify BGP route-reflector client policy. The decisive records instead include BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
C:This information cannot independently verify BGP route-reflector client policy. Route reflectors can distribute iBGP routes between clients while preserving control-plane policies.
D:This information cannot independently verify BGP route-reflector client policy. A healthy optical light without checking protocol neighbors or forwarding entries.
Question 63
Leaf switches are BGP peers of a pair of route reflectors, but prefixes received from one leaf are not reflected to another. Which statement most accurately explains this scenario?
- A device description always determines actual forwarding policy regardless of running configuration.
- All control-plane protocols exchange state automatically after a cable is inserted.
- Route reflectors can distribute iBGP routes between clients while preserving control-plane policies.
- Configuration differences between peer switches cannot affect network traffic.
Explanation
Correct Answer
C:Validation depends on BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility. This explains why the most appropriate response is to validate route-reflector client configuration and address-family policy on the designated reflectors.
Incorrect Answers
A:A device description always determines actual forwarding policy regardless of running configuration. This is an incorrect generalization for BGP route-reflector client policy. The applicable technical behavior is that route reflectors can distribute iBGP routes between clients while preserving control-plane policies. The operator should verify BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
B:All control-plane protocols exchange state automatically after a cable is inserted. This is an incorrect generalization for BGP route-reflector client policy. The applicable technical behavior is that route reflectors can distribute iBGP routes between clients while preserving control-plane policies. The operator should verify BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
D:Configuration differences between peer switches cannot affect network traffic. This is an incorrect generalization for BGP route-reflector client policy. The applicable technical behavior is that route reflectors can distribute iBGP routes between clients while preserving control-plane policies. The operator should verify BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
Question 64
Leaf switches are BGP peers of a pair of route reflectors, but prefixes received from one leaf are not reflected to another. Assume an engineer instead chooses to force a full iBGP mesh by deleting the reflectors without a design review. What is the principal technical consequence of the mistaken choice?
- The only consequence of the wrong change is a different device description.
- Verifying topology after maintenance automatically creates a switching loop.
- The defect exists solely because the engineer documented the change.
- An up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned.
Explanation
Correct Answer
D:The proper corrective action is to validate route-reflector client configuration and address-family policy on the designated reflectors. Route reflectors can distribute iBGP routes between clients while preserving control-plane policies.
Incorrect Answers
A:This does not explain the actual BGP route-reflector client policy defect after the shortcut. The meaningful failure is that an up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned.
B:This does not explain the actual BGP route-reflector client policy defect after the shortcut. The relevant evidence is BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
C:This does not explain the actual BGP route-reflector client policy defect after the shortcut. The defect exists solely because the engineer documented the change.
Question 65
Leaf switches are BGP peers of a pair of route reflectors, but prefixes received from one leaf are not reflected to another. The observed failure is: an up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned. What should the engineer do to recover and validate the service?
- Restore intended client-group and AF settings and confirm bidirectional route propagation.
- Clear the entire underlay OSPF process whenever one EVPN route is missing.
- Turn off route advertisement on all leaves as a permanent workaround.
- Force a full iBGP mesh by deleting the reflectors without a design review.
Explanation
Correct Answer
A:This addresses the observable fault while preserving a check of the expected result. Validate against BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
Incorrect Answers
B:Clear the entire underlay OSPF process whenever one EVPN route is missing. This would not reliably restore service after the stated fault. An up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned. The controlled recovery is to restore intended client-group and AF settings and confirm bidirectional route propagation.
C:Turn off route advertisement on all leaves as a permanent workaround. This would not reliably restore service after the stated fault. An up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned. The controlled recovery is to restore intended client-group and AF settings and confirm bidirectional route propagation.
D:Force a full iBGP mesh by deleting the reflectors without a design review. This would not reliably restore service after the stated fault. An up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned. The controlled recovery is to restore intended client-group and AF settings and confirm bidirectional route propagation.
Question 66
A scaled EVPN control plane shows route reflector adjacencies as up but leaves do not learn each other's advertised routes. Which next step should the data center engineer select?
- On this affected device, the engineer should clear the entire underlay OSPF process whenever one EVPN route is missing.
- On this affected device, the engineer should validate route-reflector client configuration and address-family policy on the designated reflectors.
- On this affected device, the engineer should turn off route advertisement on all leaves as a permanent workaround.
- On this affected device, the engineer should force a full iBGP mesh by deleting the reflectors without a design review.
Explanation
Correct Answer
B:This directly addresses BGP route-reflector client policy because route reflectors can distribute iBGP routes between clients while preserving control-plane policies.
Incorrect Answers
A:Clear the entire underlay OSPF process whenever one EVPN route is missing. The proposed change targets the wrong mechanism or lacks essential validation. Route reflectors can distribute iBGP routes between clients while preserving control-plane policies. Relevant evidence is BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
C:An up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned.
D:An up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned. Force a full iBGP mesh by deleting the reflectors without a design review.
Question 67
A scaled EVPN control plane shows route reflector adjacencies as up but leaves do not learn each other's advertised routes. Which diagnostic record would most strongly confirm the result?
- For this deployment, examine an up management interface without the relevant routing or forwarding table.
- For this deployment, examine one successful ping to an unrelated management address.
- For this deployment, examine BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
- For this deployment, examine an interface description without the effective peer or VXLAN policy.
Explanation
Correct Answer
C:These observations test the actual BGP route-reflector client policy mechanism rather than a superficial management status. They should be checked after validate route-reflector client configuration and address-family policy on the designated reflectors.
Incorrect Answers
A:This information cannot independently verify BGP route-reflector client policy. An up management interface without the relevant routing or forwarding table.
B:This information cannot independently verify BGP route-reflector client policy. In the given case, a scaled EVPN control plane shows route reflector adjacencies as up but leaves do not learn each other's advertised routes.
D:This information cannot independently verify BGP route-reflector client policy. An interface description without the effective peer or VXLAN policy.
Question 68
A scaled EVPN control plane shows route reflector adjacencies as up but leaves do not learn each other's advertised routes. Which platform concept should guide the engineer’s assessment?
- For this condition, the applicable principle is that configuration differences between peer switches cannot affect network traffic.
- For this condition, the applicable principle is that a device description always determines actual forwarding policy regardless of running configuration.
- For this condition, the applicable principle is that physical link carrier guarantees all overlay and routing states are correct.
- For this condition, the applicable principle is that route reflectors can distribute iBGP routes between clients while preserving control-plane policies.
Explanation
Correct Answer
D:Validation depends on BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
Incorrect Answers
A:Configuration differences between peer switches cannot affect network traffic. This is an incorrect generalization for BGP route-reflector client policy. The applicable technical behavior is that route reflectors can distribute iBGP routes between clients while preserving control-plane policies. The operator should verify BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
B:A device description always determines actual forwarding policy regardless of running configuration. This is an incorrect generalization for BGP route-reflector client policy. The applicable technical behavior is that route reflectors can distribute iBGP routes between clients while preserving control-plane policies. The operator should verify BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
C:Physical link carrier guarantees all overlay and routing states are correct. This is an incorrect generalization for BGP route-reflector client policy. The applicable technical behavior is that route reflectors can distribute iBGP routes between clients while preserving control-plane policies. The operator should verify BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
Question 69
A scaled EVPN control plane shows route reflector adjacencies as up but leaves do not learn each other's advertised routes. Assume an engineer instead chooses to force a full iBGP mesh by deleting the reflectors without a design review. Which root-cause observation follows from that incorrect change?
- The resulting defect is that an up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned.
- The resulting defect is that the defect exists solely because the engineer documented the change.
- The resulting defect is that preserving neighbor-state evidence is itself the source of the observed outage.
- The resulting defect is that verifying topology after maintenance automatically creates a switching loop.
Explanation
Correct Answer
A:The proper corrective action is to validate route-reflector client configuration and address-family policy on the designated reflectors. That is the direct consequence of choosing the misleading shortcut.
Incorrect Answers
B:The defect exists solely because the engineer documented the change. This does not explain the actual BGP route-reflector client policy defect after the shortcut. The meaningful failure is that an up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned. The relevant evidence is BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
C:Preserving neighbor-state evidence is itself the source of the observed outage. This does not explain the actual BGP route-reflector client policy defect after the shortcut. The meaningful failure is that an up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned. The relevant evidence is BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
D:Verifying topology after maintenance automatically creates a switching loop. This does not explain the actual BGP route-reflector client policy defect after the shortcut. The meaningful failure is that an up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned. The relevant evidence is BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
Question 70
A scaled EVPN control plane shows route reflector adjacencies as up but leaves do not learn each other's advertised routes. The observed failure is: an up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned. Which recovery action addresses the underlying technical fault?
- The controlled remediation is to turn off route advertisement on all leaves as a permanent workaround.
- The controlled remediation is to restore intended client-group and AF settings and confirm bidirectional route propagation.
- The controlled remediation is to force a full iBGP mesh by deleting the reflectors without a design review.
- The controlled remediation is to clear the entire underlay OSPF process whenever one EVPN route is missing.
Explanation
Correct Answer
B:Validate against BGP client relationships, AF neighbor activation, received EVPN routes, and reflected route visibility.
Incorrect Answers
A:Turn off route advertisement on all leaves as a permanent workaround. This would not reliably restore service after the stated fault. An up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned. The controlled recovery is to restore intended client-group and AF settings and confirm bidirectional route propagation.
C:Force a full iBGP mesh by deleting the reflectors without a design review. This would not reliably restore service after the stated fault. An up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned. The controlled recovery is to restore intended client-group and AF settings and confirm bidirectional route propagation.
D:Clear the entire underlay OSPF process whenever one EVPN route is missing. This would not reliably restore service after the stated fault. An up neighbor session without correct route-reflector client policy can leave overlay reachability partitioned. The controlled recovery is to restore intended client-group and AF settings and confirm bidirectional route propagation.