cert
cert-1
cert-2

Pass Cisco 350-601 Exam in First Attempt Guaranteed!

Get 100% Latest Exam Questions, Accurate & Verified Answers to Pass the Actual Exam!
30 Days Free Updates, Instant Download!

cert-5
cert-6
350-601 Exam - Verified By Experts
350-601 Premium Bundle
$29.98

350-601 Premium Bundle

$79.99
$109.97
  • Premium File 613 Questions & Answers. Last update: Nov 10, 2026
  • Training Course 143 Video Lectures
  • Study Guide 1923 Pages
 
$109.97
$79.99
accept 46 downloads in last 7 days
block-screenshots
Purchase Cisco 350-601 Exam Training Products Individually
Cisco 350-601 Premium File
Premium File 613 Q&A
$76.99$69.99
Cisco 350-601 Video Training Course
Training Course 143 Lectures
$21.99 $19.99
Cisco 350-601 PDF Study Guide
Study Guide 1923 Pages
$21.99 $19.99
Cisco 350-601 Practice Test 6

Question 50

Route reflectors accept overlay BGP TCP sessions, yet the leaves receive no EVPN NLRI after a configuration migration. The observed failure is: a green BGP session alone is not proof that EVPN MAC and IP reachability is distributed. Which remediation most directly restores the intended behavior?

  1. The controlled remediation is to treat a base TCP session as sufficient proof of overlay convergence.
  2. The controlled remediation is to activate and inspect the appropriate AF policy and verify EVPN type routes propagate to the leaves.
  3. The controlled remediation is to change only the underlay MTU without checking BGP address-family configuration.
  4. The controlled remediation is to create an FC switch port channel to transport EVPN NLRIs.

Explanation

Correct Answer

B:

A BGP transport session can be established without the EVPN address family carrying overlay reachability. Validate against BGP EVPN neighbor AF state, advertised and received EVPN routes, and VXLAN VTEP forwarding entries.

Incorrect Answers

A:

Treat a base TCP session as sufficient proof of overlay convergence. This would not reliably restore service after the stated fault. A green BGP session alone is not proof that EVPN MAC and IP reachability is distributed. The controlled recovery is to activate and inspect the appropriate AF policy and verify EVPN type routes propagate to the leaves.

C:

Change only the underlay MTU without checking BGP address-family configuration. This would not reliably restore service after the stated fault. A green BGP session alone is not proof that EVPN MAC and IP reachability is distributed. The controlled recovery is to activate and inspect the appropriate AF policy and verify EVPN type routes propagate to the leaves.

D:

Create an FC switch port channel to transport EVPN NLRIs. This would not reliably restore service after the stated fault. A green BGP session alone is not proof that EVPN MAC and IP reachability is distributed. The controlled recovery is to activate and inspect the appropriate AF policy and verify EVPN type routes propagate to the leaves.

Question 51

Two tenant VRFs have the expected VNI numbers but remote prefix advertisements never enter the receiving VRF. Which configuration decision MOST directly resolves the issue?

  1. Disable every VRF on the switch to make routes globally visible.
  2. Change only an NTP server address and expect VRF import.
  3. Correct the intended EVPN route-target import and export policy for the tenant VNI or VRF.
  4. Advertise one universal route target to all tenants without an isolation review.

Explanation

Correct Answer

C:

This directly addresses EVPN route-target import and export because BGP EVPN route targets control which overlay reachability a receiving VRF imports. Confirm the change against EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

Incorrect Answers

A:

A route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. The relevant correction is to correct the intended EVPN route-target import and export policy for the tenant VNI or VRF.

B:

Change only an NTP server address and expect VRF import. The proposed change targets the wrong mechanism or lacks essential validation. BGP EVPN route targets control which overlay reachability a receiving VRF imports. Relevant evidence is EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

D:

A route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. The appropriate action remains to correct the intended EVPN route-target import and export policy for the tenant VNI or VRF.

Question 52

Two tenant VRFs have the expected VNI numbers but remote prefix advertisements never enter the receiving VRF. What should the engineer inspect to confirm the actual state?

  1. A pre-change network diagram with no live control-plane state.
  2. A healthy optical light without checking protocol neighbors or forwarding entries.
  3. An up management interface without the relevant routing or forwarding table.
  4. EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

Explanation

Correct Answer

D:

These observations test the actual EVPN route-target import and export mechanism rather than a superficial management status. BGP EVPN route targets control which overlay reachability a receiving VRF imports.

Incorrect Answers

A:

This information cannot independently verify EVPN route-target import and export. The decisive records instead include EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

B:

This information cannot independently verify EVPN route-target import and export. BGP EVPN route targets control which overlay reachability a receiving VRF imports.

C:

This information cannot independently verify EVPN route-target import and export. An up management interface without the relevant routing or forwarding table.

Question 53

Two tenant VRFs have the expected VNI numbers but remote prefix advertisements never enter the receiving VRF. What technical behavior underlies the correct decision?

  1. BGP EVPN route targets control which overlay reachability a receiving VRF imports.
  2. All control-plane protocols exchange state automatically after a cable is inserted.
  3. Physical link carrier guarantees all overlay and routing states are correct.
  4. A working management-plane ping proves every tenant and application path is healthy.

Explanation

Correct Answer

A:

Validation depends on EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation. This explains why the most appropriate response is to correct the intended EVPN route-target import and export policy for the tenant VNI or VRF.

Incorrect Answers

B:

All control-plane protocols exchange state automatically after a cable is inserted. This is an incorrect generalization for EVPN route-target import and export. The applicable technical behavior is that BGP EVPN route targets control which overlay reachability a receiving VRF imports. The operator should verify EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

C:

Physical link carrier guarantees all overlay and routing states are correct. This is an incorrect generalization for EVPN route-target import and export. The applicable technical behavior is that BGP EVPN route targets control which overlay reachability a receiving VRF imports. The operator should verify EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

D:

A working management-plane ping proves every tenant and application path is healthy. This is an incorrect generalization for EVPN route-target import and export. The applicable technical behavior is that BGP EVPN route targets control which overlay reachability a receiving VRF imports. The operator should verify EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

Question 54

Two tenant VRFs have the expected VNI numbers but remote prefix advertisements never enter the receiving VRF. Assume an engineer instead chooses to disable every VRF on the switch to make routes globally visible. Which resulting risk or fault should the reviewer identify?

  1. Preserving neighbor-state evidence is itself the source of the observed outage.
  2. A route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF.
  3. Investigating the forwarding table is the reason a broken route cannot converge.
  4. The only consequence of the wrong change is a different device description.

Explanation

Correct Answer

B:

The proper corrective action is to correct the intended EVPN route-target import and export policy for the tenant VNI or VRF. That is the direct consequence of choosing the misleading shortcut.

Incorrect Answers

A:

Preserving neighbor-state evidence is itself the source of the observed outage. This does not explain the actual EVPN route-target import and export defect after the shortcut. The meaningful failure is that a route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. The relevant evidence is EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

C:

Investigating the forwarding table is the reason a broken route cannot converge. This does not explain the actual EVPN route-target import and export defect after the shortcut. The meaningful failure is that a route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. The relevant evidence is EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

D:

The only consequence of the wrong change is a different device description. This does not explain the actual EVPN route-target import and export defect after the shortcut. The meaningful failure is that a route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. The relevant evidence is EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

Question 55

Two tenant VRFs have the expected VNI numbers but remote prefix advertisements never enter the receiving VRF. The observed failure is: a route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. Which remediation most directly restores the intended behavior?

  1. Change only an NTP server address and expect VRF import.
  2. Advertise one universal route target to all tenants without an isolation review.
  3. Repair the narrowly scoped RT mapping and verify the expected tenant routes and isolation.
  4. Disable every VRF on the switch to make routes globally visible.

Explanation

Correct Answer

C:

This addresses the observable fault while preserving a check of the expected result. BGP EVPN route targets control which overlay reachability a receiving VRF imports.

Incorrect Answers

A:

That option would change only an NTP server address and expect VRF import, but it addresses a different concern. This addresses the observable fault while preserving a check of the expected result.

B:

Advertise one universal route target to all tenants without an isolation review. This would not reliably restore service after the stated fault. A route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. The controlled recovery is to repair the narrowly scoped RT mapping and verify the expected tenant routes and isolation.

D:

That option would disable every VRF on the switch to make routes globally visible, but it addresses a different concern. This addresses the observable fault while preserving a check of the expected result.

Question 56

A VXLAN fabric can see a remote EVPN route in BGP, yet it is not installed into the intended tenant routing table. Which operator action best meets this technical requirement?

  1. On this affected device, the engineer should change only an NTP server address and expect VRF import.
  2. On this affected device, the engineer should advertise one universal route target to all tenants without an isolation review.
  3. On this affected device, the engineer should disable every VRF on the switch to make routes globally visible.
  4. On this affected device, the engineer should correct the intended EVPN route-target import and export policy for the tenant VNI or VRF.

Explanation

Correct Answer

D:

This directly addresses EVPN route-target import and export because BGP EVPN route targets control which overlay reachability a receiving VRF imports.

Incorrect Answers

A:

Change only an NTP server address and expect VRF import. The proposed change targets the wrong mechanism or lacks essential validation. BGP EVPN route targets control which overlay reachability a receiving VRF imports. Relevant evidence is EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

B:

A route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. Advertise one universal route target to all tenants without an isolation review.

C:

A route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. Disable every VRF on the switch to make routes globally visible.

Question 57

A VXLAN fabric can see a remote EVPN route in BGP, yet it is not installed into the intended tenant routing table. Which collection of observations most directly tests the suspected cause?

  1. For this deployment, examine EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.
  2. For this deployment, examine one successful ping to an unrelated management address.
  3. For this deployment, examine a pre-change network diagram with no live control-plane state.
  4. For this deployment, examine a healthy optical light without checking protocol neighbors or forwarding entries.

Explanation

Correct Answer

A:

These observations test the actual EVPN route-target import and export mechanism rather than a superficial management status. They should be checked after correct the intended EVPN route-target import and export policy for the tenant VNI or VRF.

Incorrect Answers

B:

This information cannot independently verify EVPN route-target import and export. In the given case, a VXLAN fabric can see a remote EVPN route in BGP, yet it is not installed into the intended tenant routing table.

C:

This information cannot independently verify EVPN route-target import and export. A pre-change network diagram with no live control-plane state.

D:

This information cannot independently verify EVPN route-target import and export. A healthy optical light without checking protocol neighbors or forwarding entries.

Question 58

A VXLAN fabric can see a remote EVPN route in BGP, yet it is not installed into the intended tenant routing table. Which statement most accurately explains this scenario?

  1. For this condition, the applicable principle is that a working management-plane ping proves every tenant and application path is healthy.
  2. For this condition, the applicable principle is that BGP EVPN route targets control which overlay reachability a receiving VRF imports.
  3. For this condition, the applicable principle is that all control-plane protocols exchange state automatically after a cable is inserted.
  4. For this condition, the applicable principle is that configuration differences between peer switches cannot affect network traffic.

Explanation

Correct Answer

B:

Validation depends on EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

Incorrect Answers

A:

A working management-plane ping proves every tenant and application path is healthy. This is an incorrect generalization for EVPN route-target import and export. The applicable technical behavior is that BGP EVPN route targets control which overlay reachability a receiving VRF imports. The operator should verify EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

C:

All control-plane protocols exchange state automatically after a cable is inserted. This is an incorrect generalization for EVPN route-target import and export. The applicable technical behavior is that BGP EVPN route targets control which overlay reachability a receiving VRF imports. The operator should verify EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

D:

Configuration differences between peer switches cannot affect network traffic. This is an incorrect generalization for EVPN route-target import and export. The applicable technical behavior is that BGP EVPN route targets control which overlay reachability a receiving VRF imports. The operator should verify EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

Question 59

A VXLAN fabric can see a remote EVPN route in BGP, yet it is not installed into the intended tenant routing table. Assume an engineer instead chooses to disable every VRF on the switch to make routes globally visible. What is the principal technical consequence of the mistaken choice?

  1. The resulting defect is that the only consequence of the wrong change is a different device description.
  2. The resulting defect is that verifying topology after maintenance automatically creates a switching loop.
  3. The resulting defect is that a route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF.
  4. The resulting defect is that investigating the forwarding table is the reason a broken route cannot converge.

Explanation

Correct Answer

C:

The proper corrective action is to correct the intended EVPN route-target import and export policy for the tenant VNI or VRF. BGP EVPN route targets control which overlay reachability a receiving VRF imports.

Incorrect Answers

A:

The only consequence of the wrong change is a different device description. This does not explain the actual EVPN route-target import and export defect after the shortcut. The meaningful failure is that a route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. The relevant evidence is EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

B:

Verifying topology after maintenance automatically creates a switching loop. This does not explain the actual EVPN route-target import and export defect after the shortcut. The meaningful failure is that a route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. The relevant evidence is EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

D:

Investigating the forwarding table is the reason a broken route cannot converge. This does not explain the actual EVPN route-target import and export defect after the shortcut. The meaningful failure is that a route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. The relevant evidence is EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

Question 60

A VXLAN fabric can see a remote EVPN route in BGP, yet it is not installed into the intended tenant routing table. The observed failure is: a route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. What should the engineer do to recover and validate the service?

  1. The controlled remediation is to advertise one universal route target to all tenants without an isolation review.
  2. The controlled remediation is to disable every VRF on the switch to make routes globally visible.
  3. The controlled remediation is to change only an NTP server address and expect VRF import.
  4. The controlled remediation is to repair the narrowly scoped RT mapping and verify the expected tenant routes and isolation.

Explanation

Correct Answer

D:

This addresses the observable fault while preserving a check of the expected result. Validate against EVPN route-target attributes, VRF import policy, received prefixes, and tenant route-table installation.

Incorrect Answers

A:

Advertise one universal route target to all tenants without an isolation review. This would not reliably restore service after the stated fault. A route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. The controlled recovery is to repair the narrowly scoped RT mapping and verify the expected tenant routes and isolation.

B:

Disable every VRF on the switch to make routes globally visible. This would not reliably restore service after the stated fault. A route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. The controlled recovery is to repair the narrowly scoped RT mapping and verify the expected tenant routes and isolation.

C:

Change only an NTP server address and expect VRF import. This would not reliably restore service after the stated fault. A route may arrive at a BGP peer but remain unusable when its route target does not match the importing VRF. The controlled recovery is to repair the narrowly scoped RT mapping and verify the expected tenant routes and isolation.

Implementing and Operating Cisco Data Center Core Technologies (DCCOR) (350-601) Practice Tests