Cisco 350-601 Practice Test 2
Question 10
A newly added routed transit link shows bidirectional hellos, but the OSPF peers cannot become fully adjacent because their interface area identifiers differ. The observed failure is: adding an unrelated static route does not repair the OSPF area mismatch, leaving the expected adjacency and learned routes absent. Which remediation most directly restores the intended behavior?
- The controlled remediation is to move the affected interfaces into unrelated VRFs without a design change.
- The controlled remediation is to correct the area inconsistency, clear only the affected adjacency if required, and verify full neighbor state.
- The controlled remediation is to set a static default route and ignore the failed adjacency.
- The controlled remediation is to disable authentication on every routing interface to force convergence.
Explanation
Correct Answer
B:OSPF neighbors on a common link must agree on area and required adjacency parameters before exchanging a full link-state database. Validate against interface OSPF area settings, neighbor state, hello fields, and resulting link-state database synchronization.
Incorrect Answers
A:Move the affected interfaces into unrelated VRFs without a design change. This would not reliably restore service after the stated fault. Adding an unrelated static route does not repair the OSPF area mismatch, leaving the expected adjacency and learned routes absent. The controlled recovery is to correct the area inconsistency, clear only the affected adjacency if required, and verify full neighbor state.
C:Set a static default route and ignore the failed adjacency. This would not reliably restore service after the stated fault. Adding an unrelated static route does not repair the OSPF area mismatch, leaving the expected adjacency and learned routes absent. The controlled recovery is to correct the area inconsistency, clear only the affected adjacency if required, and verify full neighbor state.
D:Disable authentication on every routing interface to force convergence. This would not reliably restore service after the stated fault. Adding an unrelated static route does not repair the OSPF area mismatch, leaving the expected adjacency and learned routes absent. The controlled recovery is to correct the area inconsistency, clear only the affected adjacency if required, and verify full neighbor state.
Question 11
A pair of Nexus routers has IPv6 addressing on its transit link, but the OSPFv3 neighbors never form after the routing process was enabled on different interfaces. Which configuration decision MOST directly resolves the issue?
- Configure only an IPv4 OSPFv2 network statement and expect OSPFv3 to discover peers.
- Replace all IPv6 link-local addresses with NAT translations.
- Enable the correct OSPFv3 instance and area on both participating IPv6 interfaces and validate the link-local neighbor exchange.
- Disable IPv6 routing on the transit link while retaining OSPFv3.
Explanation
Correct Answer
C:This directly addresses OSPFv3 IPv6 neighbor discovery because OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link. Confirm the change against OSPFv3 interface enablement, link-local addresses, IPv6 hello captures, and neighbor state on both peers.
Incorrect Answers
A:IPv6 reachability alone does not establish that OSPFv3 is enabled on the same adjacency interfaces. The relevant correction is to enable the correct OSPFv3 instance and area on both participating IPv6 interfaces and validate the link-local neighbor exchange.
B:That option would replace all IPv6 link-local addresses with NAT translations, but it addresses a different concern. This directly addresses OSPFv3 IPv6 neighbor discovery because OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link.
D:IPv6 reachability alone does not establish that OSPFv3 is enabled on the same adjacency interfaces. The appropriate action remains to enable the correct OSPFv3 instance and area on both participating IPv6 interfaces and validate the link-local neighbor exchange.
Question 12
A pair of Nexus routers has IPv6 addressing on its transit link, but the OSPFv3 neighbors never form after the routing process was enabled on different interfaces. What should the engineer inspect to confirm the actual state?
- One successful ping to an unrelated management address.
- An interface description without the effective peer or VXLAN policy.
- A healthy optical light without checking protocol neighbors or forwarding entries.
- OSPFv3 interface enablement, link-local addresses, IPv6 hello captures, and neighbor state on both peers.
Explanation
Correct Answer
D:These observations test the actual OSPFv3 IPv6 neighbor discovery mechanism rather than a superficial management status. OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link.
Incorrect Answers
A:This information cannot independently verify OSPFv3 IPv6 neighbor discovery. The decisive records instead include OSPFv3 interface enablement, link-local addresses, IPv6 hello captures, and neighbor state on both peers.
B:This information cannot independently verify OSPFv3 IPv6 neighbor discovery. OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link.
C:This information cannot independently verify OSPFv3 IPv6 neighbor discovery. A healthy optical light without checking protocol neighbors or forwarding entries.
Question 13
A pair of Nexus routers has IPv6 addressing on its transit link, but the OSPFv3 neighbors never form after the routing process was enabled on different interfaces. What technical behavior underlies the correct decision?
- OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link.
- A device description always determines actual forwarding policy regardless of running configuration.
- All control-plane protocols exchange state automatically after a cable is inserted.
- Configuration differences between peer switches cannot affect network traffic.
Explanation
Correct Answer
A:Validation depends on OSPFv3 interface enablement, link-local addresses, IPv6 hello captures, and neighbor state on both peers. This explains why the most appropriate response is to enable the correct OSPFv3 instance and area on both participating IPv6 interfaces and validate the link-local neighbor exchange.
Incorrect Answers
B:A device description always determines actual forwarding policy regardless of running configuration. This is an incorrect generalization for OSPFv3 IPv6 neighbor discovery. The applicable technical behavior is that OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link. The operator should verify OSPFv3 interface enablement, link-local addresses, IPv6 hello captures, and neighbor state on both peers.
C:All control-plane protocols exchange state automatically after a cable is inserted. This is an incorrect generalization for OSPFv3 IPv6 neighbor discovery. The applicable technical behavior is that OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link. The operator should verify OSPFv3 interface enablement, link-local addresses, IPv6 hello captures, and neighbor state on both peers.
D:Configuration differences between peer switches cannot affect network traffic. This is an incorrect generalization for OSPFv3 IPv6 neighbor discovery. The applicable technical behavior is that OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link. The operator should verify OSPFv3 interface enablement, link-local addresses, IPv6 hello captures, and neighbor state on both peers.
Question 14
A pair of Nexus routers has IPv6 addressing on its transit link, but the OSPFv3 neighbors never form after the routing process was enabled on different interfaces. Assume an engineer instead chooses to configure only an IPv4 OSPFv2 network statement and expect OSPFv3 to discover peers. Which resulting risk or fault should the reviewer identify?
- The only consequence of the wrong change is a different device description.
- IPv6 reachability alone does not establish that OSPFv3 is enabled on the same adjacency interfaces.
- Verifying topology after maintenance automatically creates a switching loop.
- The defect exists solely because the engineer documented the change.
Explanation
Correct Answer
B:OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link. That is the direct consequence of choosing the misleading shortcut.
Incorrect Answers
A:This does not explain the actual OSPFv3 IPv6 neighbor discovery defect after the shortcut. The meaningful failure is that iPv6 reachability alone does not establish that OSPFv3 is enabled on the same adjacency interfaces.
C:This does not explain the actual OSPFv3 IPv6 neighbor discovery defect after the shortcut. The relevant evidence is OSPFv3 interface enablement, link-local addresses, IPv6 hello captures, and neighbor state on both peers.
D:This does not explain the actual OSPFv3 IPv6 neighbor discovery defect after the shortcut. The defect exists solely because the engineer documented the change.
Question 15
A pair of Nexus routers has IPv6 addressing on its transit link, but the OSPFv3 neighbors never form after the routing process was enabled on different interfaces. The observed failure is: iPv6 reachability alone does not establish that OSPFv3 is enabled on the same adjacency interfaces. Which remediation most directly restores the intended behavior?
- Replace all IPv6 link-local addresses with NAT translations.
- Disable IPv6 routing on the transit link while retaining OSPFv3.
- Restore matching OSPFv3 interface settings and confirm full neighbor state and learned IPv6 routes.
- Configure only an IPv4 OSPFv2 network statement and expect OSPFv3 to discover peers.
Explanation
Correct Answer
C:OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link. This addresses the observable fault while preserving a check of the expected result.
Incorrect Answers
A:That option would replace all IPv6 link-local addresses with NAT translations, but it addresses a different concern. This addresses the observable fault while preserving a check of the expected result.
B:That option would disable IPv6 routing on the transit link while retaining OSPFv3, but it addresses a different concern. This addresses the observable fault while preserving a check of the expected result.
D:That option would configure only an IPv4 OSPFv2 network statement and expect OSPFv3 to discover peers, but it addresses a different concern. This addresses the observable fault while preserving a check of the expected result.
Question 16
A new IPv6 routed uplink carries IPv6 packets successfully, yet engineers see no OSPFv3 adjacency on one side. Which operator action best meets this technical requirement?
- On this affected device, the engineer should replace all IPv6 link-local addresses with NAT translations.
- On this affected device, the engineer should disable IPv6 routing on the transit link while retaining OSPFv3.
- On this affected device, the engineer should configure only an IPv4 OSPFv2 network statement and expect OSPFv3 to discover peers.
- On this affected device, the engineer should enable the correct OSPFv3 instance and area on both participating IPv6 interfaces and validate the link-local neighbor exchange.
Explanation
Correct Answer
D:This directly addresses OSPFv3 IPv6 neighbor discovery because OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link.
Incorrect Answers
A:Replace all IPv6 link-local addresses with NAT translations. The proposed change targets the wrong mechanism or lacks essential validation. OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link. Relevant evidence is OSPFv3 interface enablement, link-local addresses, IPv6 hello captures, and neighbor state on both peers.
B:IPv6 reachability alone does not establish that OSPFv3 is enabled on the same adjacency interfaces. Disable IPv6 routing on the transit link while retaining OSPFv3.
C:IPv6 reachability alone does not establish that OSPFv3 is enabled on the same adjacency interfaces. Configure only an IPv4 OSPFv2 network statement and expect OSPFv3 to discover peers.
Question 17
A new IPv6 routed uplink carries IPv6 packets successfully, yet engineers see no OSPFv3 adjacency on one side. Which collection of observations most directly tests the suspected cause?
- For this deployment, examine OSPFv3 interface enablement, link-local addresses, IPv6 hello captures, and neighbor state on both peers.
- For this deployment, examine an up management interface without the relevant routing or forwarding table.
- For this deployment, examine one successful ping to an unrelated management address.
- For this deployment, examine an interface description without the effective peer or VXLAN policy.
Explanation
Correct Answer
A:These observations test the actual OSPFv3 IPv6 neighbor discovery mechanism rather than a superficial management status. They should be checked after enable the correct OSPFv3 instance and area on both participating IPv6 interfaces and validate the link-local neighbor exchange.
Incorrect Answers
B:This information cannot independently verify OSPFv3 IPv6 neighbor discovery. An up management interface without the relevant routing or forwarding table.
C:This information cannot independently verify OSPFv3 IPv6 neighbor discovery. In the given case, a new IPv6 routed uplink carries IPv6 packets successfully, yet engineers see no OSPFv3 adjacency on one side.
D:This information cannot independently verify OSPFv3 IPv6 neighbor discovery. An interface description without the effective peer or VXLAN policy.
Question 18
A new IPv6 routed uplink carries IPv6 packets successfully, yet engineers see no OSPFv3 adjacency on one side. Which statement most accurately explains this scenario?
- For this condition, the applicable principle is that configuration differences between peer switches cannot affect network traffic.
- For this condition, the applicable principle is that OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link.
- For this condition, the applicable principle is that a device description always determines actual forwarding policy regardless of running configuration.
- For this condition, the applicable principle is that physical link carrier guarantees all overlay and routing states are correct.
Explanation
Correct Answer
B:Validation depends on OSPFv3 interface enablement, link-local addresses, IPv6 hello captures, and neighbor state on both peers.
Incorrect Answers
A:Configuration differences between peer switches cannot affect network traffic. This is an incorrect generalization for OSPFv3 IPv6 neighbor discovery. The applicable technical behavior is that OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link. The operator should verify OSPFv3 interface enablement, link-local addresses, IPv6 hello captures, and neighbor state on both peers.
C:A device description always determines actual forwarding policy regardless of running configuration. This is an incorrect generalization for OSPFv3 IPv6 neighbor discovery. The applicable technical behavior is that OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link. The operator should verify OSPFv3 interface enablement, link-local addresses, IPv6 hello captures, and neighbor state on both peers.
D:Physical link carrier guarantees all overlay and routing states are correct. This is an incorrect generalization for OSPFv3 IPv6 neighbor discovery. The applicable technical behavior is that OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link. The operator should verify OSPFv3 interface enablement, link-local addresses, IPv6 hello captures, and neighbor state on both peers.
Question 19
A new IPv6 routed uplink carries IPv6 packets successfully, yet engineers see no OSPFv3 adjacency on one side. Assume an engineer instead chooses to configure only an IPv4 OSPFv2 network statement and expect OSPFv3 to discover peers. What is the principal technical consequence of the mistaken choice?
- The resulting defect is that the defect exists solely because the engineer documented the change.
- The resulting defect is that preserving neighbor-state evidence is itself the source of the observed outage.
- The resulting defect is that iPv6 reachability alone does not establish that OSPFv3 is enabled on the same adjacency interfaces.
- The resulting defect is that verifying topology after maintenance automatically creates a switching loop.
Explanation
Correct Answer
C:OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link. The proper corrective action is to enable the correct OSPFv3 instance and area on both participating IPv6 interfaces and validate the link-local neighbor exchange.
Incorrect Answers
A:This does not explain the actual OSPFv3 IPv6 neighbor discovery defect after the shortcut. In the given case, a new IPv6 routed uplink carries IPv6 packets successfully, yet engineers see no OSPFv3 adjacency on one side.
B:This does not explain the actual OSPFv3 IPv6 neighbor discovery defect after the shortcut. Preserving neighbor-state evidence is itself the source of the observed outage.
D:This does not explain the actual OSPFv3 IPv6 neighbor discovery defect after the shortcut. Verifying topology after maintenance automatically creates a switching loop.
Question 20
A new IPv6 routed uplink carries IPv6 packets successfully, yet engineers see no OSPFv3 adjacency on one side. The observed failure is: iPv6 reachability alone does not establish that OSPFv3 is enabled on the same adjacency interfaces. What should the engineer do to recover and validate the service?
- The controlled remediation is to disable IPv6 routing on the transit link while retaining OSPFv3.
- The controlled remediation is to configure only an IPv4 OSPFv2 network statement and expect OSPFv3 to discover peers.
- The controlled remediation is to replace all IPv6 link-local addresses with NAT translations.
- The controlled remediation is to restore matching OSPFv3 interface settings and confirm full neighbor state and learned IPv6 routes.
Explanation
Correct Answer
D:OSPFv3 adjacency formation relies on matching protocol configuration and IPv6 link-local exchanges on the link. Validate against OSPFv3 interface enablement, link-local addresses, IPv6 hello captures, and neighbor state on both peers.
Incorrect Answers
A:Disable IPv6 routing on the transit link while retaining OSPFv3. This would not reliably restore service after the stated fault. IPv6 reachability alone does not establish that OSPFv3 is enabled on the same adjacency interfaces. The controlled recovery is to restore matching OSPFv3 interface settings and confirm full neighbor state and learned IPv6 routes.
B:Configure only an IPv4 OSPFv2 network statement and expect OSPFv3 to discover peers. This would not reliably restore service after the stated fault. IPv6 reachability alone does not establish that OSPFv3 is enabled on the same adjacency interfaces. The controlled recovery is to restore matching OSPFv3 interface settings and confirm full neighbor state and learned IPv6 routes.
C:Replace all IPv6 link-local addresses with NAT translations. This would not reliably restore service after the stated fault. IPv6 reachability alone does not establish that OSPFv3 is enabled on the same adjacency interfaces. The controlled recovery is to restore matching OSPFv3 interface settings and confirm full neighbor state and learned IPv6 routes.