Cisco 350-601 Practice Test 10
Question 90
New receivers cannot join a PIM sparse-mode group although local IGMP reports work after an RP change. The observed failure is: an incorrect or unreachable RP prevents intended sparse-mode group registration and receiver joins. Which remediation most directly restores the intended behavior?
- The controlled remediation is to assume any OSPF adjacency automatically supplies the correct PIM RP.
- The controlled remediation is to correct RP reachability and mappings and verify group-specific multicast state.
- The controlled remediation is to disable IGMP on every receiver VLAN and rely on ARP.
- The controlled remediation is to change a Fibre Channel zone name to restore PIM joins.
Explanation
Correct Answer
B:PIM sparse mode relies on the configured RP for relevant shared-tree discovery and forwarding behavior. Validate against rP mapping, unicast reachability to the RP, PIM neighbors, and multicast join state.
Incorrect Answers
A:Assume any OSPF adjacency automatically supplies the correct PIM RP. This would not reliably restore service after the stated fault. An incorrect or unreachable RP prevents intended sparse-mode group registration and receiver joins. The controlled recovery is to correct RP reachability and mappings and verify group-specific multicast state.
C:Disable IGMP on every receiver VLAN and rely on ARP. This would not reliably restore service after the stated fault. An incorrect or unreachable RP prevents intended sparse-mode group registration and receiver joins. The controlled recovery is to correct RP reachability and mappings and verify group-specific multicast state.
D:Change a Fibre Channel zone name to restore PIM joins. This would not reliably restore service after the stated fault. An incorrect or unreachable RP prevents intended sparse-mode group registration and receiver joins. The controlled recovery is to correct RP reachability and mappings and verify group-specific multicast state.
Question 91
Two redundant first-hop gateways agree on a virtual IP, but active service does not move after the preferred upstream path fails. Which configuration decision MOST directly resolves the issue?
- Modify the hosts' DNS suffix to influence FHRP elections.
- Disable FHRP on both devices during normal production.
- Configure appropriate object or interface tracking and preemption policy for the FHRP design.
- Give both physical routers the exact same unique management address.
Explanation
Correct Answer
C:This directly addresses fHRP active gateway failover because first-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway. Confirm the change against fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability.
Incorrect Answers
A:Without tracking, an active gateway can continue attracting traffic despite loss of essential upstream reachability. The relevant correction is to configure appropriate object or interface tracking and preemption policy for the FHRP design.
B:Disable FHRP on both devices during normal production. The proposed change targets the wrong mechanism or lacks essential validation. First-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway. Relevant evidence is fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability.
D:Without tracking, an active gateway can continue attracting traffic despite loss of essential upstream reachability. The appropriate action remains to configure appropriate object or interface tracking and preemption policy for the FHRP design.
Question 92
Two redundant first-hop gateways agree on a virtual IP, but active service does not move after the preferred upstream path fails. What should the engineer inspect to confirm the actual state?
- An interface description without the effective peer or VXLAN policy.
- An up management interface without the relevant routing or forwarding table.
- One successful ping to an unrelated management address.
- FHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability.
Explanation
Correct Answer
D:These observations test the actual fHRP active gateway failover mechanism rather than a superficial management status. First-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway.
Incorrect Answers
A:This information cannot independently verify fHRP active gateway failover. The decisive records instead include fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability.
B:This information cannot independently verify fHRP active gateway failover. First-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway.
C:This information cannot independently verify fHRP active gateway failover. In the given case, two redundant first-hop gateways agree on a virtual IP, but active service does not move after the preferred upstream path fails.
Question 93
Two redundant first-hop gateways agree on a virtual IP, but active service does not move after the preferred upstream path fails. What technical behavior underlies the correct decision?
- First-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway.
- Physical link carrier guarantees all overlay and routing states are correct.
- Configuration differences between peer switches cannot affect network traffic.
- A device description always determines actual forwarding policy regardless of running configuration.
Explanation
Correct Answer
A:Validation depends on fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability. This explains why the most appropriate response is to configure appropriate object or interface tracking and preemption policy for the FHRP design.
Incorrect Answers
B:Physical link carrier guarantees all overlay and routing states are correct. This is an incorrect generalization for fHRP active gateway failover. The applicable technical behavior is that first-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway. The operator should verify fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability.
C:Configuration differences between peer switches cannot affect network traffic. This is an incorrect generalization for fHRP active gateway failover. The applicable technical behavior is that first-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway. The operator should verify fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability.
D:A device description always determines actual forwarding policy regardless of running configuration. This is an incorrect generalization for fHRP active gateway failover. The applicable technical behavior is that first-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway. The operator should verify fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability.
Question 94
Two redundant first-hop gateways agree on a virtual IP, but active service does not move after the preferred upstream path fails. Assume an engineer instead chooses to modify the hosts' DNS suffix to influence FHRP elections. Which resulting risk or fault should the reviewer identify?
- Verifying topology after maintenance automatically creates a switching loop.
- Without tracking, an active gateway can continue attracting traffic despite loss of essential upstream reachability.
- The defect exists solely because the engineer documented the change.
- Preserving neighbor-state evidence is itself the source of the observed outage.
Explanation
Correct Answer
B:The proper corrective action is to configure appropriate object or interface tracking and preemption policy for the FHRP design. First-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway.
Incorrect Answers
A:This does not explain the actual fHRP active gateway failover defect after the shortcut. The meaningful failure is that without tracking, an active gateway can continue attracting traffic despite loss of essential upstream reachability.
C:This does not explain the actual fHRP active gateway failover defect after the shortcut. The relevant evidence is fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability.
D:This does not explain the actual fHRP active gateway failover defect after the shortcut. In the given case, two redundant first-hop gateways agree on a virtual IP, but active service does not move after the preferred upstream path fails.
Question 95
Two redundant first-hop gateways agree on a virtual IP, but active service does not move after the preferred upstream path fails. The observed failure is: without tracking, an active gateway can continue attracting traffic despite loss of essential upstream reachability. Which remediation most directly restores the intended behavior?
- Disable FHRP on both devices during normal production.
- Give both physical routers the exact same unique management address.
- Repair tracking and election policy, simulate controlled uplink failure, and validate gateway continuity.
- Modify the hosts' DNS suffix to influence FHRP elections.
Explanation
Correct Answer
C:Validate against fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability. This addresses the observable fault while preserving a check of the expected result.
Incorrect Answers
A:Disable FHRP on both devices during normal production. This would not reliably restore service after the stated fault. Without tracking, an active gateway can continue attracting traffic despite loss of essential upstream reachability. The controlled recovery is to repair tracking and election policy, simulate controlled uplink failure, and validate gateway continuity.
B:Give both physical routers the exact same unique management address. This would not reliably restore service after the stated fault. Without tracking, an active gateway can continue attracting traffic despite loss of essential upstream reachability. The controlled recovery is to repair tracking and election policy, simulate controlled uplink failure, and validate gateway continuity.
D:Modify the hosts' DNS suffix to influence FHRP elections. This would not reliably restore service after the stated fault. Without tracking, an active gateway can continue attracting traffic despite loss of essential upstream reachability. The controlled recovery is to repair tracking and election policy, simulate controlled uplink failure, and validate gateway continuity.
Question 96
A shared VLAN's HSRP active device loses its routed uplink yet retains the virtual gateway role and blackholes hosts. Which operator action best meets this technical requirement?
- On this affected device, the engineer should disable FHRP on both devices during normal production.
- On this affected device, the engineer should give both physical routers the exact same unique management address.
- On this affected device, the engineer should modify the hosts' DNS suffix to influence FHRP elections.
- On this affected device, the engineer should configure appropriate object or interface tracking and preemption policy for the FHRP design.
Explanation
Correct Answer
D:This directly addresses fHRP active gateway failover because first-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway.
Incorrect Answers
A:Disable FHRP on both devices during normal production. The proposed change targets the wrong mechanism or lacks essential validation. First-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway. Relevant evidence is fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability.
B:Without tracking, an active gateway can continue attracting traffic despite loss of essential upstream reachability. Give both physical routers the exact same unique management address.
C:Without tracking, an active gateway can continue attracting traffic despite loss of essential upstream reachability. Modify the hosts' DNS suffix to influence FHRP elections.
Question 97
A shared VLAN's HSRP active device loses its routed uplink yet retains the virtual gateway role and blackholes hosts. Which collection of observations most directly tests the suspected cause?
- For this deployment, examine fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability.
- For this deployment, examine a pre-change network diagram with no live control-plane state.
- For this deployment, examine an interface description without the effective peer or VXLAN policy.
- For this deployment, examine an up management interface without the relevant routing or forwarding table.
Explanation
Correct Answer
A:These observations test the actual fHRP active gateway failover mechanism rather than a superficial management status. They should be checked after configure appropriate object or interface tracking and preemption policy for the FHRP design.
Incorrect Answers
B:This information cannot independently verify fHRP active gateway failover. A pre-change network diagram with no live control-plane state.
C:This information cannot independently verify fHRP active gateway failover. An interface description without the effective peer or VXLAN policy.
D:This information cannot independently verify fHRP active gateway failover. An up management interface without the relevant routing or forwarding table.
Question 98
A shared VLAN's HSRP active device loses its routed uplink yet retains the virtual gateway role and blackholes hosts. Which statement most accurately explains this scenario?
- For this condition, the applicable principle is that a device description always determines actual forwarding policy regardless of running configuration.
- For this condition, the applicable principle is that first-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway.
- For this condition, the applicable principle is that physical link carrier guarantees all overlay and routing states are correct.
- For this condition, the applicable principle is that a working management-plane ping proves every tenant and application path is healthy.
Explanation
Correct Answer
B:Validation depends on fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability. First-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway.
Incorrect Answers
A:A device description always determines actual forwarding policy regardless of running configuration. This is an incorrect generalization for fHRP active gateway failover. The applicable technical behavior is that first-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway. The operator should verify fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability.
C:Physical link carrier guarantees all overlay and routing states are correct. This is an incorrect generalization for fHRP active gateway failover. The applicable technical behavior is that first-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway. The operator should verify fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability.
D:A working management-plane ping proves every tenant and application path is healthy. This is an incorrect generalization for fHRP active gateway failover. The applicable technical behavior is that first-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway. The operator should verify fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability.
Question 99
A shared VLAN's HSRP active device loses its routed uplink yet retains the virtual gateway role and blackholes hosts. Assume an engineer instead chooses to modify the hosts' DNS suffix to influence FHRP elections. What is the principal technical consequence of the mistaken choice?
- The resulting defect is that preserving neighbor-state evidence is itself the source of the observed outage.
- The resulting defect is that investigating the forwarding table is the reason a broken route cannot converge.
- The resulting defect is that without tracking, an active gateway can continue attracting traffic despite loss of essential upstream reachability.
- The resulting defect is that the defect exists solely because the engineer documented the change.
Explanation
Correct Answer
C:The proper corrective action is to configure appropriate object or interface tracking and preemption policy for the FHRP design. That is the direct consequence of choosing the misleading shortcut.
Incorrect Answers
A:This does not explain the actual fHRP active gateway failover defect after the shortcut. Preserving neighbor-state evidence is itself the source of the observed outage.
B:This does not explain the actual fHRP active gateway failover defect after the shortcut. Investigating the forwarding table is the reason a broken route cannot converge.
D:This does not explain the actual fHRP active gateway failover defect after the shortcut. The defect exists solely because the engineer documented the change.
Question 100
A shared VLAN's HSRP active device loses its routed uplink yet retains the virtual gateway role and blackholes hosts. The observed failure is: without tracking, an active gateway can continue attracting traffic despite loss of essential upstream reachability. What should the engineer do to recover and validate the service?
- The controlled remediation is to give both physical routers the exact same unique management address.
- The controlled remediation is to modify the hosts' DNS suffix to influence FHRP elections.
- The controlled remediation is to disable FHRP on both devices during normal production.
- The controlled remediation is to repair tracking and election policy, simulate controlled uplink failure, and validate gateway continuity.
Explanation
Correct Answer
D:Validate against fHRP active and standby states, tracked-object status, priority changes, and host default-gateway reachability. First-hop redundancy requires a health-aware election so the reachable device carries the virtual gateway.
Incorrect Answers
A:Give both physical routers the exact same unique management address. This would not reliably restore service after the stated fault. Without tracking, an active gateway can continue attracting traffic despite loss of essential upstream reachability. The controlled recovery is to repair tracking and election policy, simulate controlled uplink failure, and validate gateway continuity.
B:Modify the hosts' DNS suffix to influence FHRP elections. This would not reliably restore service after the stated fault. Without tracking, an active gateway can continue attracting traffic despite loss of essential upstream reachability. The controlled recovery is to repair tracking and election policy, simulate controlled uplink failure, and validate gateway continuity.
C:Disable FHRP on both devices during normal production. This would not reliably restore service after the stated fault. Without tracking, an active gateway can continue attracting traffic despite loss of essential upstream reachability. The controlled recovery is to repair tracking and election policy, simulate controlled uplink failure, and validate gateway continuity.