Cisco 300-410 Practice Test 55
Question 540
Following a production change at the Newark enterprise edge, a spoke can reach the hub's public interface but GRE traffic is rejected following a tunnel template change. The incident is affecting an operations uplink; the response team has a rollback window. The new configuration worsens service. Which controlled rollback should the team perform?
- Restore the prior multicast map if the change floods routing hellos to unintended endpoints.
- Disable the shortcut change if dynamic mappings direct traffic to an untrusted or unreachable NBMA address.
- Reapply the last common tunnel key if multiple peers lose overlay connectivity.
- Roll back the IPsec proposal atomically on both sides if secure tunnel establishment fails.
Explanation
Correct Answer
C:Reapply the last common tunnel key if multiple peers lose overlay connectivity. A GRE tunnel key mismatch can prevent compatible overlay traffic from being accepted.
Incorrect Answers
A:Restore the prior multicast map if the change floods routing hellos to unintended endpoints. This is a rollback for a different component (DMVPN multicast neighbor discovery), where Dynamic routing across GRE/mGRE requires the overlay to carry its multicast or broadcast control traffic. Here the evidence instead concerns dmvpn tunnel key consistency: A GRE tunnel key mismatch can prevent compatible overlay traffic from being accepted.
B:Disable the shortcut change if dynamic mappings direct traffic to an untrusted or unreachable NBMA address. This is a rollback for a different component (DMVPN phase 3 shortcut), where DMVPN phase 3 uses hub redirects and spoke shortcuts to facilitate direct spoke-to-spoke forwarding. Here the evidence instead concerns dmvpn tunnel key consistency: A GRE tunnel key mismatch can prevent compatible overlay traffic from being accepted.
D:Roll back the IPsec proposal atomically on both sides if secure tunnel establishment fails. This is a rollback for a different component (DMVPN IPsec protection mismatch), where DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay. Here the evidence instead concerns dmvpn tunnel key consistency: A GRE tunnel key mismatch can prevent compatible overlay traffic from being accepted.
Question 541
Following a production change at the Portland regional hub, remote SSH management fails only from the new administration subnet while other approved management subnets work. The incident is affecting a business-critical application; the response team has a rollback window. Which observation is the strongest first diagnostic check for this symptom?
- Inspect IP SLA UDP-jitter measurements for one-way or round-trip delay variation and loss.
- Inspect the VTY access-class, source subnet permit entries, and applied inbound direction.
- Compare local logging buffer settings with remote trap severity and collector-side filtering.
- Check UDP/69 transfer initiation, server write permissions, and return data-channel filtering.
Explanation
Correct Answer
B:Inspect the VTY access-class, source subnet permit entries, and applied inbound direction. A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
Incorrect Answers
A:Inspect IP SLA UDP-jitter measurements for one-way or round-trip delay variation and loss. This is an investigation for a different failure condition (IP SLA UDP jitter monitoring), where Jitter-sensitive applications need measurements of delay variation and loss, not just ICMP reachability. Here the evidence instead concerns vty access-class: A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
C:Compare local logging buffer settings with remote trap severity and collector-side filtering. This is an investigation for a different failure condition (Syslog severity filtering), where Local logging and remote syslog use separate targets and severity thresholds. Here the evidence instead concerns vty access-class: A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
D:Check UDP/69 transfer initiation, server write permissions, and return data-channel filtering. This is an investigation for a different failure condition (TFTP configuration transfer), where TFTP is a UDP file-transfer service; successful ICMP reachability does not prove file-transfer access. Here the evidence instead concerns vty access-class: A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
Question 542
Following a production change at the Portland regional hub, remote SSH management fails only from the new administration subnet while other approved management subnets work. The incident is affecting a business-critical application; the response team has a rollback window. What change best addresses the root mechanism without unnecessarily changing other paths?
- Deploy an appropriately timed UDP-jitter operation to a supported responder for the voice path.
- Add a least-privilege VTY access-class exception for the authorized administration subnet.
- Correct the VTY AAA binding for remote access while preserving console emergency management.
- Correct the exporter's receiver, source, and transport settings without changing the flow record unnecessarily.
Explanation
Correct Answer
B:Add a least-privilege VTY access-class exception for the authorized administration subnet. A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
Incorrect Answers
A:Deploy an appropriately timed UDP-jitter operation to a supported responder for the voice path. This is a configuration change for a different root cause (IP SLA UDP jitter monitoring), where Jitter-sensitive applications need measurements of delay variation and loss, not just ICMP reachability. Here the evidence instead concerns vty access-class: A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
C:Correct the VTY AAA binding for remote access while preserving console emergency management. This is a configuration change for a different root cause (Console versus VTY authentication), where Console and VTY lines can use different authentication and authorization methods. Here the evidence instead concerns vty access-class: A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
D:Correct the exporter's receiver, source, and transport settings without changing the flow record unnecessarily. This is a configuration change for a different root cause (NetFlow exporter destination), where Flow collection and export are distinct: valid local cache entries do not imply successful export transport. Here the evidence instead concerns vty access-class: A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
Question 543
Following a production change at the Portland regional hub, remote SSH management fails only from the new administration subnet while other approved management subnets work. The incident is affecting a business-critical application; the response team has a rollback window. Which verification result would provide the most relevant acceptance evidence?
- Generate known flows and verify cache entries and corresponding exported records.
- Flap a test interface and confirm an event notification reaches the NMS promptly.
- Test SSH access from the approved source and denial from unauthorized sources.
- Trigger a known test event and verify the message arrives with expected severity and facility.
Explanation
Correct Answer
C:Test SSH access from the approved source and denial from unauthorized sources. A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
Incorrect Answers
A:Generate known flows and verify cache entries and corresponding exported records. This is a validation for another mechanism (Flexible NetFlow monitor attachment), where Flexible NetFlow requires a record/monitor and an appropriate interface or platform attachment to observe flows. Here the evidence instead concerns vty access-class: A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
B:Flap a test interface and confirm an event notification reaches the NMS promptly. This is a validation for another mechanism (SNMP traps versus polling), where SNMP traps and informs send asynchronous notifications; polling alone is periodic and can miss brief events. Here the evidence instead concerns vty access-class: A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
D:Trigger a known test event and verify the message arrives with expected severity and facility. This is a validation for another mechanism (Syslog severity filtering), where Local logging and remote syslog use separate targets and severity thresholds. Here the evidence instead concerns vty access-class: A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
Question 544
Following a production change at the Portland regional hub, remote SSH management fails only from the new administration subnet while other approved management subnets work. The incident is affecting a business-critical application; the response team has a rollback window. Which TWO complementary steps provide both relevant fault isolation and a controlled correction?
- Check RA managed-config flag, DHCPv6 relay destination, and routed reachability to the service.
- Inspect the VTY access-class, source subnet permit entries, and applied inbound direction.
- Configure the correct ip helper-address on the client-facing routed interface.
- Add a least-privilege VTY access-class exception for the authorized administration subnet.
Explanation
Correct Answers
B:Inspect the VTY access-class, source subnet permit entries, and applied inbound direction. A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
D:Add a least-privilege VTY access-class exception for the authorized administration subnet. A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
Incorrect Answers
A:Check RA managed-config flag, DHCPv6 relay destination, and routed reachability to the service. This is an investigation for a different failure condition (DHCPv6 relay), where DHCPv6 relaying transports client messages to a remote server; Router Advertisements still convey default-router details. Here the evidence instead concerns vty access-class: A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
C:Configure the correct ip helper-address on the client-facing routed interface. This is a configuration change for a different root cause (IPv4 DHCP relay), where IPv4 DHCP Discover broadcasts require a relay when the DHCP server resides beyond a Layer 3 boundary. Here the evidence instead concerns vty access-class: A VTY access-class restricts which source addresses can open remote terminal sessions to the router.
Question 545
Following a production change at the Dayton hospital campus, a BGP session remains Idle or Active after the neighbor router's autonomous-system assignment changes. The incident is affecting a monitored campus segment; the response team has a rollback window. Which observation is the strongest first diagnostic check for this symptom?
- Check the client's reflector-client configuration, session state, and cluster metadata.
- Inspect local preference distributed in iBGP along with route selection results.
- Inspect the received BGP next-hop address and its reachability in the IGP or VRF.
- Inspect TCP reachability and confirm the neighbor's configured remote-as matches its new AS.
Explanation
Correct Answer
D:Inspect TCP reachability and confirm the neighbor's configured remote-as matches its new AS. BGP neighbors must agree on configured peer AS identity and establish a TCP session.
Incorrect Answers
A:Check the client's reflector-client configuration, session state, and cluster metadata. This is an investigation for a different failure condition (BGP route reflector clients), where Route reflectors relax iBGP split-horizon for configured clients while using loop-prevention attributes. Here the evidence instead concerns bgp peer remote as: BGP neighbors must agree on configured peer AS identity and establish a TCP session.
B:Inspect local preference distributed in iBGP along with route selection results. This is an investigation for a different failure condition (BGP outbound path local preference), where Within an AS, higher BGP local preference normally wins before AS-path length and MED. Here the evidence instead concerns bgp peer remote as: BGP neighbors must agree on configured peer AS identity and establish a TCP session.
C:Inspect the received BGP next-hop address and its reachability in the IGP or VRF. This is an investigation for a different failure condition (BGP iBGP next-hop reachability), where An iBGP speaker commonly preserves next-hop attributes unless explicitly changed, so next-hop resolution matters. Here the evidence instead concerns bgp peer remote as: BGP neighbors must agree on configured peer AS identity and establish a TCP session.
Question 546
Following a production change at the Dayton hospital campus, a BGP session remains Idle or Active after the neighbor router's autonomous-system assignment changes. The incident is affecting a monitored campus segment; the response team has a rollback window. What change best addresses the root mechanism without unnecessarily changing other paths?
- Correct the BGP neighbor remote-as and related peer policy for the intended eBGP or iBGP relationship.
- Apply an explicit allowlist prefix policy outbound to the external BGP peer.
- Use next-hop-self at the correct iBGP advertising boundary or repair the actual next-hop reachability.
- Prepend the local AS on selected backup advertisements if permitted by upstream routing policy.
Explanation
Correct Answer
A:Correct the BGP neighbor remote-as and related peer policy for the intended eBGP or iBGP relationship. BGP neighbors must agree on configured peer AS identity and establish a TCP session.
Incorrect Answers
B:Apply an explicit allowlist prefix policy outbound to the external BGP peer. This is a configuration change for a different root cause (BGP prefix leak prevention), where BGP outbound prefix policies are the control point for which routes are advertised to an external neighbor. Here the evidence instead concerns bgp peer remote as: BGP neighbors must agree on configured peer AS identity and establish a TCP session.
C:Use next-hop-self at the correct iBGP advertising boundary or repair the actual next-hop reachability. This is a configuration change for a different root cause (BGP iBGP next-hop reachability), where An iBGP speaker commonly preserves next-hop attributes unless explicitly changed, so next-hop resolution matters. Here the evidence instead concerns bgp peer remote as: BGP neighbors must agree on configured peer AS identity and establish a TCP session.
D:Prepend the local AS on selected backup advertisements if permitted by upstream routing policy. This is a configuration change for a different root cause (BGP inbound traffic engineering), where AS-path prepending can make an advertised path less attractive to remote BGP networks, but cannot guarantee inbound routing. Here the evidence instead concerns bgp peer remote as: BGP neighbors must agree on configured peer AS identity and establish a TCP session.
Question 547
Following a production change at the Dayton hospital campus, a BGP session remains Idle or Active after the neighbor router's autonomous-system assignment changes. The incident is affecting a monitored campus segment; the response team has a rollback window. Which verification result would provide the most relevant acceptance evidence?
- Confirm internal BGP speakers consistently choose the preferred exit while backup remains available.
- Verify TCP 179 establishment using the loopback source and an Established BGP session.
- Verify the BGP session establishes and receives only authorized prefixes.
- Confirm the BGP next hop resolves and received routes become installable in the RIB.
Explanation
Correct Answer
C:Verify the BGP session establishes and receives only authorized prefixes. BGP neighbors must agree on configured peer AS identity and establish a TCP session.
Incorrect Answers
A:Confirm internal BGP speakers consistently choose the preferred exit while backup remains available. This is a validation for another mechanism (BGP outbound path local preference), where Within an AS, higher BGP local preference normally wins before AS-path length and MED. Here the evidence instead concerns bgp peer remote as: BGP neighbors must agree on configured peer AS identity and establish a TCP session.
B:Verify TCP 179 establishment using the loopback source and an Established BGP session. This is a validation for another mechanism (Loopback-sourced eBGP session), where Default eBGP TTL and packet source are designed for directly connected peers; loopback peering needs explicit settings. Here the evidence instead concerns bgp peer remote as: BGP neighbors must agree on configured peer AS identity and establish a TCP session.
D:Confirm the BGP next hop resolves and received routes become installable in the RIB. This is a validation for another mechanism (BGP iBGP next-hop reachability), where An iBGP speaker commonly preserves next-hop attributes unless explicitly changed, so next-hop resolution matters. Here the evidence instead concerns bgp peer remote as: BGP neighbors must agree on configured peer AS identity and establish a TCP session.
Question 548
Following a production change at the Dayton hospital campus, a BGP session remains Idle or Active after the neighbor router's autonomous-system assignment changes. The incident is affecting a monitored campus segment; the response team has a rollback window. Which TWO complementary steps provide both relevant fault isolation and a controlled correction?
- Correct the BGP neighbor remote-as and related peer policy for the intended eBGP or iBGP relationship.
- Inspect TCP reachability and confirm the neighbor's configured remote-as matches its new AS.
- Inspect outbound prefix filters and route-map hit counts for unauthorized advertisements.
- Set a higher local preference for the preferred egress using a scoped inbound policy at the edge.
Explanation
Correct Answers
A:Correct the BGP neighbor remote-as and related peer policy for the intended eBGP or iBGP relationship. BGP neighbors must agree on configured peer AS identity and establish a TCP session.
B:Inspect TCP reachability and confirm the neighbor's configured remote-as matches its new AS. BGP neighbors must agree on configured peer AS identity and establish a TCP session.
Incorrect Answers
C:Inspect outbound prefix filters and route-map hit counts for unauthorized advertisements. This is an investigation for a different failure condition (BGP prefix leak prevention), where BGP outbound prefix policies are the control point for which routes are advertised to an external neighbor. Here the evidence instead concerns bgp peer remote as: BGP neighbors must agree on configured peer AS identity and establish a TCP session.
D:Set a higher local preference for the preferred egress using a scoped inbound policy at the edge. This is a configuration change for a different root cause (BGP outbound path local preference), where Within an AS, higher BGP local preference normally wins before AS-path length and MED. Here the evidence instead concerns bgp peer remote as: BGP neighbors must agree on configured peer AS identity and establish a TCP session.
Question 549
Following a production change at the Mobile distribution campus, a redistribution route map includes a deny clause followed by a permit clause, and some authorized prefixes never reach the next routing process. The incident is affecting management access; the response team has a rollback window. Which observation is the strongest first diagnostic check for this symptom?
- Compare summary reachability with the actual set of component subnets and the summary discard route.
- Inspect route-map sequence order, each match condition, and hit counts against the missing prefixes.
- Inspect the redistribution source, subnets handling, and whether a match or prefix filter excludes /27.
- Trace route tags and redistribution points to identify reintroduction of the same route.
Explanation
Correct Answer
B:Inspect route-map sequence order, each match condition, and hit counts against the missing prefixes. Route maps are processed by ordered sequence; the first matching clause determines the permit or deny action.
Incorrect Answers
A:Compare summary reachability with the actual set of component subnets and the summary discard route. This is an investigation for a different failure condition (Summary route black hole), where An aggregate can intentionally create a discard route and must not promise reachability for withdrawn component networks. Here the evidence instead concerns route-map permit sequence: Route maps are processed by ordered sequence; the first matching clause determines the permit or deny action.
C:Inspect the redistribution source, subnets handling, and whether a match or prefix filter excludes /27. This is an investigation for a different failure condition (OSPF classless redistribution), where Redistribution must explicitly cover intended classless networks while avoiding uncontrolled route leakage. Here the evidence instead concerns route-map permit sequence: Route maps are processed by ordered sequence; the first matching clause determines the permit or deny action.
D:Trace route tags and redistribution points to identify reintroduction of the same route. This is an investigation for a different failure condition (Redistribution loop prevention tags), where Consistent route tagging and inbound redistribution filters help prevent feedback loops across routing domains. Here the evidence instead concerns route-map permit sequence: Route maps are processed by ordered sequence; the first matching clause determines the permit or deny action.
Question 550
Following a production change at the Mobile distribution campus, a redistribution route map includes a deny clause followed by a permit clause, and some authorized prefixes never reach the next routing process. The incident is affecting management access; the response team has a rollback window. What change best addresses the root mechanism without unnecessarily changing other paths?
- Provide the required EIGRP seed metric through redistribution or a route map for the intended source.
- Correct the more-specific route or its advertisement if it is unintended; do not only change the aggregate's distance.
- Refine the aggregate or restore specific reachable routes so the advertisement does not imply missing coverage.
- Put the intended permit conditions before the catch-all deny or narrow the deny match.
Explanation
Correct Answer
D:Put the intended permit conditions before the catch-all deny or narrow the deny match. Route maps are processed by ordered sequence; the first matching clause determines the permit or deny action.
Incorrect Answers
A:Provide the required EIGRP seed metric through redistribution or a route map for the intended source. This is a configuration change for a different root cause (EIGRP redistribution seed metric), where EIGRP redistribution generally needs an appropriate seed metric for external routes. Here the evidence instead concerns route-map permit sequence: Route maps are processed by ordered sequence; the first matching clause determines the permit or deny action.
B:Correct the more-specific route or its advertisement if it is unintended; do not only change the aggregate's distance. This is a configuration change for a different root cause (Longest-prefix selection), where A longer matching prefix is selected before administrative distance is compared among equal-length routes. Here the evidence instead concerns route-map permit sequence: Route maps are processed by ordered sequence; the first matching clause determines the permit or deny action.
C:Refine the aggregate or restore specific reachable routes so the advertisement does not imply missing coverage. This is a configuration change for a different root cause (Summary route black hole), where An aggregate can intentionally create a discard route and must not promise reachability for withdrawn component networks. Here the evidence instead concerns route-map permit sequence: Route maps are processed by ordered sequence; the first matching clause determines the permit or deny action.