Cisco 300-410 Practice Test 20
Question 190
Following a production change at the Aurora remote operations location, a router learns 10.44.0.0/16 from OSPF and from a floating static route, but the static next hop is used even while OSPF is healthy. The incident is affecting remote-site route stability; the response team has a rollback window. What change best addresses the root mechanism without unnecessarily changing other paths?
- Tag routes on first redistribution and deny that tag when importing them back into the source domain.
- Allow the intended subnet with classless redistribution and a scoped route map instead of exporting everything.
- Raise the static route's distance above the intended OSPF route or remove the unwanted override.
- Correct the more-specific route or its advertisement if it is unintended; do not only change the aggregate's distance.
Explanation
Correct Answer
C:Raise the static route's distance above the intended OSPF route or remove the unwanted override. For the same destination prefix, the router prefers the eligible route with the lower administrative distance after longest-prefix selection.
Incorrect Answers
A:Tag routes on first redistribution and deny that tag when importing them back into the source domain. This is a configuration change for a different root cause (Redistribution loop prevention tags), where Consistent route tagging and inbound redistribution filters help prevent feedback loops across routing domains. Here the evidence instead concerns administrative distance: For the same destination prefix, the router prefers the eligible route with the lower administrative distance after longest-prefix selection.
B:Allow the intended subnet with classless redistribution and a scoped route map instead of exporting everything. This is a configuration change for a different root cause (OSPF classless redistribution), where Redistribution must explicitly cover intended classless networks while avoiding uncontrolled route leakage. Here the evidence instead concerns administrative distance: For the same destination prefix, the router prefers the eligible route with the lower administrative distance after longest-prefix selection.
D:Correct the more-specific route or its advertisement if it is unintended; do not only change the aggregate's distance. This is a configuration change for a different root cause (Longest-prefix selection), where A longer matching prefix is selected before administrative distance is compared among equal-length routes. Here the evidence instead concerns administrative distance: For the same destination prefix, the router prefers the eligible route with the lower administrative distance after longest-prefix selection.
Question 191
Following a production change at the Aurora remote operations location, a router learns 10.44.0.0/16 from OSPF and from a floating static route, but the static next hop is used even while OSPF is healthy. The incident is affecting remote-site route stability; the response team has a rollback window. Which verification result would provide the most relevant acceptance evidence?
- Verify the OSPF route wins when healthy and the static route takes over only when the primary disappears.
- Use a destination-specific forwarding lookup to confirm which most-specific route is selected.
- Verify the external EIGRP route and plausible composite metric appear in neighbor tables.
- Verify reimported tagged routes are blocked while fresh authorized external prefixes remain visible.
Explanation
Correct Answer
A:Verify the OSPF route wins when healthy and the static route takes over only when the primary disappears. For the same destination prefix, the router prefers the eligible route with the lower administrative distance after longest-prefix selection.
Incorrect Answers
B:Use a destination-specific forwarding lookup to confirm which most-specific route is selected. This is a validation for another mechanism (Longest-prefix selection), where A longer matching prefix is selected before administrative distance is compared among equal-length routes. Here the evidence instead concerns administrative distance: For the same destination prefix, the router prefers the eligible route with the lower administrative distance after longest-prefix selection.
C:Verify the external EIGRP route and plausible composite metric appear in neighbor tables. This is a validation for another mechanism (EIGRP redistribution seed metric), where EIGRP redistribution generally needs an appropriate seed metric for external routes. Here the evidence instead concerns administrative distance: For the same destination prefix, the router prefers the eligible route with the lower administrative distance after longest-prefix selection.
D:Verify reimported tagged routes are blocked while fresh authorized external prefixes remain visible. This is a validation for another mechanism (Redistribution loop prevention tags), where Consistent route tagging and inbound redistribution filters help prevent feedback loops across routing domains. Here the evidence instead concerns administrative distance: For the same destination prefix, the router prefers the eligible route with the lower administrative distance after longest-prefix selection.
Question 192
Following a production change at the Aurora remote operations location, a router learns 10.44.0.0/16 from OSPF and from a floating static route, but the static next hop is used even while OSPF is healthy. The incident is affecting remote-site route stability; the response team has a rollback window. The new configuration worsens service. Which controlled rollback should the team perform?
- Reapply the former metric and route-map configuration if new routes displace stable paths.
- Restore the previously recorded distances and route source if the intended failover changes.
- Undo the new redistribution scope if unexpected external routes appear.
- Restore the previous ordered route-map clauses if the permitted set becomes too broad.
Explanation
Correct Answer
B:Restore the previously recorded distances and route source if the intended failover changes. For the same destination prefix, the router prefers the eligible route with the lower administrative distance after longest-prefix selection.
Incorrect Answers
A:Reapply the former metric and route-map configuration if new routes displace stable paths. This is a rollback for a different component (EIGRP redistribution seed metric), where EIGRP redistribution generally needs an appropriate seed metric for external routes. Here the evidence instead concerns administrative distance: For the same destination prefix, the router prefers the eligible route with the lower administrative distance after longest-prefix selection.
C:Undo the new redistribution scope if unexpected external routes appear. This is a rollback for a different component (OSPF classless redistribution), where Redistribution must explicitly cover intended classless networks while avoiding uncontrolled route leakage. Here the evidence instead concerns administrative distance: For the same destination prefix, the router prefers the eligible route with the lower administrative distance after longest-prefix selection.
D:Restore the previous ordered route-map clauses if the permitted set becomes too broad. This is a rollback for a different component (Route-map permit sequence), where Route maps are processed by ordered sequence; the first matching clause determines the permit or deny action. Here the evidence instead concerns administrative distance: For the same destination prefix, the router prefers the eligible route with the lower administrative distance after longest-prefix selection.
Question 193
During a scheduled validation at the Madison enterprise edge, a spoke's NHRP adjacency worked until the IPsec proposal changed, after which GRE-over-IPsec traffic stops. Engineers must restore a monitored campus segment without disturbing unrelated production services. Which investigation should be prioritized before the engineer modifies configuration?
- Check NHRP multicast mapping and the GRE mode used to carry multicast routing hellos.
- Inspect the IKE peer identity, key selection, and authentication failure logs for the changed NBMA address.
- Inspect NHRP redirect generation on the hub and shortcut handling on spokes.
- Compare IKE/IPsec negotiation output, transform proposals, key lifetimes, and peer reachability.
Explanation
Correct Answer
D:Compare IKE/IPsec negotiation output, transform proposals, key lifetimes, and peer reachability. DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
Incorrect Answers
A:Check NHRP multicast mapping and the GRE mode used to carry multicast routing hellos. This is an investigation for a different failure condition (DMVPN multicast neighbor discovery), where Dynamic routing across GRE/mGRE requires the overlay to carry its multicast or broadcast control traffic. Here the evidence instead concerns dmvpn ipsec protection mismatch: DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
B:Inspect the IKE peer identity, key selection, and authentication failure logs for the changed NBMA address. This is an investigation for a different failure condition (IKE peer authentication), where IKE peer authentication is independent of NHRP and must match the correct endpoint identity and credentials. Here the evidence instead concerns dmvpn ipsec protection mismatch: DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
C:Inspect NHRP redirect generation on the hub and shortcut handling on spokes. This is an investigation for a different failure condition (DMVPN phase 3 shortcut), where DMVPN phase 3 uses hub redirects and spoke shortcuts to facilitate direct spoke-to-spoke forwarding. Here the evidence instead concerns dmvpn ipsec protection mismatch: DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
Question 194
During a scheduled validation at the Madison enterprise edge, a spoke's NHRP adjacency worked until the IPsec proposal changed, after which GRE-over-IPsec traffic stops. Engineers must restore a monitored campus segment without disturbing unrelated production services. Which targeted configuration or policy correction best resolves the described fault?
- Update the authorized peer authentication mapping or identity policy to match the new underlay endpoint.
- Correct the spoke's NHRP next-hop server and hub tunnel-to-NBMA map for its reachable hub.
- Align supported IPsec proposals and tunnel protection profiles on both endpoints without downgrading policy.
- Apply a routing policy consistent with the chosen DMVPN phase and intended spoke next-hop behavior.
Explanation
Correct Answer
C:Align supported IPsec proposals and tunnel protection profiles on both endpoints without downgrading policy. DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
Incorrect Answers
A:Update the authorized peer authentication mapping or identity policy to match the new underlay endpoint. This is a configuration change for a different root cause (IKE peer authentication), where IKE peer authentication is independent of NHRP and must match the correct endpoint identity and credentials. Here the evidence instead concerns dmvpn ipsec protection mismatch: DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
B:Correct the spoke's NHRP next-hop server and hub tunnel-to-NBMA map for its reachable hub. This is a configuration change for a different root cause (DMVPN NHS mapping), where A spoke typically needs valid NHRP hub mappings and an NHS to bootstrap DMVPN registration. Here the evidence instead concerns dmvpn ipsec protection mismatch: DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
D:Apply a routing policy consistent with the chosen DMVPN phase and intended spoke next-hop behavior. This is a configuration change for a different root cause (EIGRP on DMVPN hub), where DMVPN routing adjacency, next-hop propagation, and NHRP shortcut operation must be designed together. Here the evidence instead concerns dmvpn ipsec protection mismatch: DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
Question 195
During a scheduled validation at the Madison enterprise edge, a spoke's NHRP adjacency worked until the IPsec proposal changed, after which GRE-over-IPsec traffic stops. Engineers must restore a monitored campus segment without disturbing unrelated production services. Which post-change check most directly establishes that the repair is correct?
- Verify IPsec SAs form and protected DMVPN traffic increments encapsulation/decapsulation counters.
- Verify a spoke obtains a shortcut mapping and subsequent traffic uses a direct spoke-to-spoke tunnel.
- Check show ip nhrp and tunnel state for successful registration after the correction.
- Verify secure IKE and IPsec associations form with the expected peer identity.
Explanation
Correct Answer
A:Verify IPsec SAs form and protected DMVPN traffic increments encapsulation/decapsulation counters. DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
Incorrect Answers
B:Verify a spoke obtains a shortcut mapping and subsequent traffic uses a direct spoke-to-spoke tunnel. This is a validation for another mechanism (DMVPN phase 3 shortcut), where DMVPN phase 3 uses hub redirects and spoke shortcuts to facilitate direct spoke-to-spoke forwarding. Here the evidence instead concerns dmvpn ipsec protection mismatch: DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
C:Check show ip nhrp and tunnel state for successful registration after the correction. This is a validation for another mechanism (DMVPN NHRP network ID), where NHRP network identifiers help distinguish DMVPN clouds and must match the intended overlay design. Here the evidence instead concerns dmvpn ipsec protection mismatch: DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
D:Verify secure IKE and IPsec associations form with the expected peer identity. This is a validation for another mechanism (IKE peer authentication), where IKE peer authentication is independent of NHRP and must match the correct endpoint identity and credentials. Here the evidence instead concerns dmvpn ipsec protection mismatch: DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
Question 196
During a scheduled validation at the Madison enterprise edge, a spoke's NHRP adjacency worked until the IPsec proposal changed, after which GRE-over-IPsec traffic stops. Engineers must restore a monitored campus segment without disturbing unrelated production services. The attempted fix creates a regression. Which scoped recovery action is most appropriate?
- Revert any change that strips the VPN label before the egress PE can identify the target VRF.
- Roll back the IPsec proposal atomically on both sides if secure tunnel establishment fails.
- Restore the previous hub route propagation policy if spoke reachability regresses.
- Remove the new RT imports if other customers' routes become visible.
Explanation
Correct Answer
B:Roll back the IPsec proposal atomically on both sides if secure tunnel establishment fails. DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
Incorrect Answers
A:Revert any change that strips the VPN label before the egress PE can identify the target VRF. This is a rollback for a different component (MPLS L3VPN label stack), where In MPLS L3VPN, the transport label carries packets across the core and the VPN label identifies the service at the egress PE. Here the evidence instead concerns dmvpn ipsec protection mismatch: DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
C:Restore the previous hub route propagation policy if spoke reachability regresses. This is a rollback for a different component (EIGRP on DMVPN hub), where DMVPN routing adjacency, next-hop propagation, and NHRP shortcut operation must be designed together. Here the evidence instead concerns dmvpn ipsec protection mismatch: DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
D:Remove the new RT imports if other customers' routes become visible. This is a rollback for a different component (MPLS VPN route target import), where Route targets control which VPNv4 routes a VRF imports and exports; an RD provides uniqueness rather than membership. Here the evidence instead concerns dmvpn ipsec protection mismatch: DMVPN tunnel protection requires compatible IPsec/IKE parameters for a successful protected GRE overlay.
Question 197
During a scheduled validation at the Chandler warehouse network, iPv6 clients receive DNS options from an unauthorized DHCPv6 responder on a user access switch port. Engineers must restore an operations uplink without disturbing unrelated production services. Which investigation should be prioritized before the engineer modifies configuration?
- Inspect DHCPv6 Guard policy role and identify which port is sourcing server replies.
- Read ACL entries in sequence and review hit counts for the relevant source, destination, protocol, and port.
- Check ACL type, source-only matching, direction, and placement relative to branch and destination.
- Inspect AAA command-authorization method lists, server response attributes, and privilege level for the operator.
Explanation
Correct Answer
A:Inspect DHCPv6 Guard policy role and identify which port is sourcing server replies. DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.
Incorrect Answers
B:Read ACL entries in sequence and review hit counts for the relevant source, destination, protocol, and port. This is an investigation for a different failure condition (Extended ACL first-match semantics), where Extended ACL processing stops on the first matching entry, followed by an implicit deny if none matches. Here the evidence instead concerns dhcpv6 server guard: DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.
C:Check ACL type, source-only matching, direction, and placement relative to branch and destination. This is an investigation for a different failure condition (Standard IPv4 ACL placement), where Standard IPv4 ACLs match source addresses, so placement can cause unintended broad filtering. Here the evidence instead concerns dhcpv6 server guard: DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.
D:Inspect AAA command-authorization method lists, server response attributes, and privilege level for the operator. This is an investigation for a different failure condition (TACACS+ command authorization), where TACACS+ can authorize individual CLI commands separately from successful login authentication. Here the evidence instead concerns dhcpv6 server guard: DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.
Question 198
During a scheduled validation at the Chandler warehouse network, iPv6 clients receive DNS options from an unauthorized DHCPv6 responder on a user access switch port. Engineers must restore an operations uplink without disturbing unrelated production services. Which targeted configuration or policy correction best resolves the described fault?
- Apply DHCPv6 guard to untrusted client ports and permit only the authorized server-facing path.
- Enable supported ND inspection and guard policies on the affected access segment with proper trust boundaries.
- Correct the scoped TACACS+ command set or method-list binding without granting unrestricted administrative privilege.
- Place the standard ACL nearer the intended destination or use a scoped extended ACL when destination precision is required.
Explanation
Correct Answer
A:Apply DHCPv6 guard to untrusted client ports and permit only the authorized server-facing path. DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.
Incorrect Answers
B:Enable supported ND inspection and guard policies on the affected access segment with proper trust boundaries. This is a configuration change for a different root cause (IPv6 Neighbor Discovery inspection), where IPv6 ND inspection uses neighbor state and filtering to mitigate neighbor-discovery spoofing. Here the evidence instead concerns dhcpv6 server guard: DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.
C:Correct the scoped TACACS+ command set or method-list binding without granting unrestricted administrative privilege. This is a configuration change for a different root cause (TACACS+ command authorization), where TACACS+ can authorize individual CLI commands separately from successful login authentication. Here the evidence instead concerns dhcpv6 server guard: DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.
D:Place the standard ACL nearer the intended destination or use a scoped extended ACL when destination precision is required. This is a configuration change for a different root cause (Standard IPv4 ACL placement), where Standard IPv4 ACLs match source addresses, so placement can cause unintended broad filtering. Here the evidence instead concerns dhcpv6 server guard: DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.
Question 199
During a scheduled validation at the Chandler warehouse network, iPv6 clients receive DNS options from an unauthorized DHCPv6 responder on a user access switch port. Engineers must restore an operations uplink without disturbing unrelated production services. Which post-change check most directly establishes that the repair is correct?
- Validate known legitimate asymmetric flows pass while spoofed invalid-source packets remain denied.
- Test traffic during and after the authorized window and inspect relevant ACL hit counts.
- Check authorized encrypted SSH access succeeds and Telnet connection attempts fail.
- Verify clients retain legitimate DHCPv6 configuration and reject responses from the unauthorized access port.
Explanation
Correct Answer
D:Verify clients retain legitimate DHCPv6 configuration and reject responses from the unauthorized access port. DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.
Incorrect Answers
A:Validate known legitimate asymmetric flows pass while spoofed invalid-source packets remain denied. This is a validation for another mechanism (Strict uRPF asymmetric routing), where Strict uRPF can reject a packet when the best reverse route points to an interface other than its ingress. Here the evidence instead concerns dhcpv6 server guard: DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.
B:Test traffic during and after the authorized window and inspect relevant ACL hit counts. This is a validation for another mechanism (Time-based ACL), where Time-based ACL entries depend on correct local time and an actively applied time-range definition. Here the evidence instead concerns dhcpv6 server guard: DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.
C:Check authorized encrypted SSH access succeeds and Telnet connection attempts fail. This is a validation for another mechanism (Router SSH hardened management), where SSH provides encrypted remote CLI transport; Telnet sends sessions without encryption. Here the evidence instead concerns dhcpv6 server guard: DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.
Question 200
During a scheduled validation at the Chandler warehouse network, iPv6 clients receive DNS options from an unauthorized DHCPv6 responder on a user access switch port. Engineers must restore an operations uplink without disturbing unrelated production services. The attempted fix creates a regression. Which scoped recovery action is most appropriate?
- Restore the previous server command set if the change unintentionally expands administrator access.
- Restore the former ACL order if the specific permit unintentionally opens additional sources.
- Revert transport restriction only under controlled emergency access if SSH setup breaks all management.
- Restore a legitimately trusted uplink role if authorized DHCPv6 replies stop reaching clients.
Explanation
Correct Answer
D:Restore a legitimately trusted uplink role if authorized DHCPv6 replies stop reaching clients. DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.
Incorrect Answers
A:Restore the previous server command set if the change unintentionally expands administrator access. This is a rollback for a different component (TACACS+ command authorization), where TACACS+ can authorize individual CLI commands separately from successful login authentication. Here the evidence instead concerns dhcpv6 server guard: DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.
B:Restore the former ACL order if the specific permit unintentionally opens additional sources. This is a rollback for a different component (Extended ACL first-match semantics), where Extended ACL processing stops on the first matching entry, followed by an implicit deny if none matches. Here the evidence instead concerns dhcpv6 server guard: DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.
C:Revert transport restriction only under controlled emergency access if SSH setup breaks all management. This is a rollback for a different component (Router SSH hardened management), where SSH provides encrypted remote CLI transport; Telnet sends sessions without encryption. Here the evidence instead concerns dhcpv6 server guard: DHCPv6 Guard helps prevent rogue DHCPv6 server messages from untrusted switch ports.