Juniper JN0-664 Practice Test 44
Question 430
A Junos service-provider routing engineer investigates this service-provider network scenario. Two provider nodes have reachable loopbacks yet their Layer 2 circuit remains Down due to missing LDP signaling and the operator attempts to modify BGP unicast policy instead. Which TWO complementary steps combine a suitable technical action and its direct verification? Select TWO answers.
- Select the supported inter-AS or carrier-of-carriers VPN interconnection model according to trust, labels, MP-BGP signaling and administrative boundary requirements.
- Trace an LDP Layer 2 circuit end to end using neighbor signaling, pseudowire identifiers and operational connection state before changing customer VLANs.
- Use reverse-path forwarding checks to determine why an arriving multicast packet is accepted on one interface but discarded on another.
- Inspect show l2circuit connections, LDP session state, neighbor addresses, VC IDs, service-facing interfaces and transport LSP reachability.
- Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs.
Explanation
Correct Answers
B:The case-specific routing and services action is: Trace an LDP Layer 2 circuit end to end using neighbor signaling, pseudowire identifiers and operational connection state before changing customer VLANs. Verify the decision through: Inspect show l2circuit connections, LDP session state, neighbor addresses, VC IDs, service-facing interfaces and transport LSP reachability.
D:The direct discriminating observation is: Inspect show l2circuit connections, LDP session state, neighbor addresses, VC IDs, service-facing interfaces and transport LSP reachability.
Incorrect Answers
A:This alternative proposes: Select the supported inter-AS or carrier-of-carriers VPN interconnection model according to trust, labels, MP-BGP signaling and administrative boundary requirements. It concerns a different Junos engineering issue Interprovider Layer 3 VPN options and carrier of carriers, not the directly tested provider-network issue LDP signaled Layer 2 circuit pseudowire status and VC identifiers in the stated situation (Two provider nodes have reachable loopbacks yet their Layer 2 circuit remains Down due to missing LDP signaling and the operator attempts to modify BGP unicast policy instead.). A better case-specific check is: Inspect show l2circuit connections, LDP session state, neighbor addresses, VC IDs, service-facing interfaces and transport LSP reachability. The more targeted action is: Trace an LDP Layer 2 circuit end to end using neighbor signaling, pseudowire identifiers and operational connection state before changing customer VLANs.
C:This alternative proposes: Use reverse-path forwarding checks to determine why an arriving multicast packet is accepted on one interface but discarded on another. It concerns a different Junos engineering issue Multicast RPF validation and source reachability, not the directly tested provider-network issue LDP signaled Layer 2 circuit pseudowire status and VC identifiers.
E:This alternative proposes: Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs. It concerns a different Junos engineering issue Layer 2 pseudowire MTU and control-word interworking, not the directly tested provider-network issue LDP signaled Layer 2 circuit pseudowire status and VC identifiers in the stated situation (Two provider nodes have reachable loopbacks yet their Layer 2 circuit remains Down due to missing LDP signaling and the operator attempts to modify BGP unicast policy instead.). A better case-specific check is: Inspect show l2circuit connections, LDP session state, neighbor addresses, VC IDs, service-facing interfaces and transport LSP reachability. The more targeted action is: Trace an LDP Layer 2 circuit end to end using neighbor signaling, pseudowire identifiers and operational connection state before changing customer VLANs.
Question 431
A Junos service-provider routing engineer investigates the following routing and service incident: A wholesale Ethernet service passes small ping frames but drops larger customer frames after Q-in-Q tags and MPLS labels increase actual transmitted size. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.
- Validate EVPN multihoming Ethernet segment identifiers and designated-forwarder behavior before activating redundant customer links.
- Investigate an OSPF adjacency that remains in ExStart or Exchange by comparing interface MTU and protocol parameters before resetting every neighbor.
- Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail.
- Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding.
Explanation
Correct Answer
C:The case-specific routing and services action is: Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail. The governing Junos routing/service principle is: Pseudowire transport can impose encapsulation overhead and require compatible payload/MTU or control-word behavior; signaling Up does not guarantee all customer frame sizes are successfully delivered.
Incorrect Answers
A:This alternative proposes: Validate EVPN multihoming Ethernet segment identifiers and designated-forwarder behavior before activating redundant customer links. It concerns a different Junos engineering issue EVPN Ethernet segment multihoming and designated forwarder, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
B:This alternative proposes: Investigate an OSPF adjacency that remains in ExStart or Exchange by comparing interface MTU and protocol parameters before resetting every neighbor. It concerns a different Junos engineering issue OSPF adjacency MTU and hello compatibility diagnosis, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
D:This alternative proposes: Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding. It concerns a different Junos engineering issue EVPN MAC IP route type two control plane and learning, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
Question 432
A provider routing design review considers this situation. A wholesale Ethernet service passes small ping frames but drops larger customer frames after Q-in-Q tags and MPLS labels increase actual transmitted size. A colleague proposes: Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail. Which technical principle BEST supports that action? Select ONE best answer.
- EVPN commonly conveys MAC reachability through BGP route type 2; optional IP binding and policies support host learning and next-hop selection, while label or encapsulation rules depend on the deployment.
- OSPFv3 uses IPv6-related control-plane processing and link-local neighbor communication; it must be configured and verified according to the selected address family and release.
- Pseudowire transport can impose encapsulation overhead and require compatible payload/MTU or control-word behavior; signaling Up does not guarantee all customer frame sizes are successfully delivered.
- An LDP-signaled pseudowire uses locally and remotely agreed circuit identifiers, transport paths and VC labels; mismatched endpoints or identifiers can prevent service Up state.
Explanation
Correct Answer
C:The relevant Junos service-provider networking principle is: Pseudowire transport can impose encapsulation overhead and require compatible payload/MTU or control-word behavior; signaling Up does not guarantee all customer frame sizes are successfully delivered. In the described provider-network case (A wholesale Ethernet service passes small ping frames but drops larger customer frames after Q-in-Q tags and MPLS labels increase actual transmitted size.), it supports the planned action: Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail.
Incorrect Answers
A:This alternative proposes: EVPN commonly conveys MAC reachability through BGP route type 2; optional IP binding and policies support host learning and next-hop selection, while label or encapsulation rules depend on the deployment. It concerns a different Junos engineering issue EVPN MAC IP route type two control plane and learning, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
B:This alternative proposes: OSPFv3 uses IPv6-related control-plane processing and link-local neighbor communication; it must be configured and verified according to the selected address family and release. It concerns a different Junos engineering issue OSPFv3 IPv6 neighbor and IPv4 separation, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
D:This alternative proposes: An LDP-signaled pseudowire uses locally and remotely agreed circuit identifiers, transport paths and VC labels; mismatched endpoints or identifiers can prevent service Up state. It concerns a different Junos engineering issue LDP signaled Layer 2 circuit pseudowire status and VC identifiers, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
Question 433
A Juniper service-provider engineer needs decisive verification evidence for this situation. A wholesale Ethernet service passes small ping frames but drops larger customer frames after Q-in-Q tags and MPLS labels increase actual transmitted size. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.
- Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables.
- Review route-policy terms, L1 and L2 route databases, leaked prefix entries, interface scope and next-hop resolution from affected access devices.
- Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs.
- Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state.
Explanation
Correct Answer
C:The direct discriminating observation is: Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs. In the stated situation (A wholesale Ethernet service passes small ping frames but drops larger customer frames after Q-in-Q tags and MPLS labels increase actual transmitted size.), the intended acceptance outcome is: The customer transports frames within the agreed service MTU without unexplained fragmentation, truncation or interworking incompatibility.
Incorrect Answers
A:This alternative proposes: Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables. It concerns a different Junos engineering issue EVPN MAC IP route type two control plane and learning, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
B:This alternative proposes: Review route-policy terms, L1 and L2 route databases, leaked prefix entries, interface scope and next-hop resolution from affected access devices. It concerns a different Junos engineering issue IS-IS Level 2 to Level 1 route leaking and summaries, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
D:This alternative proposes: Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state. It concerns a different Junos engineering issue BGP-signaled Layer 2 VPN NLRI and route target import, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
Question 434
A service-provider acceptance team reviews the result of a provider-service change. A wholesale Ethernet service passes small ping frames but drops larger customer frames after Q-in-Q tags and MPLS labels increase actual transmitted size. The intended verification is: Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs. Which outcome BEST demonstrates success? Select ONE best answer.
- Customer traffic follows learned remote PE paths and floods only where required without generating a provider-wide bridging loop.
- The configured mode serves actual receivers without uncontrolled multicast flood in sparsely subscribed provider regions.
- A moved customer endpoint is reachable through its current PE and stale advertised paths are withdrawn or updated according to supported mobility behavior.
- The customer transports frames within the agreed service MTU without unexplained fragmentation, truncation or interworking incompatibility.
Explanation
Correct Answer
D:The verified success outcome is: The customer transports frames within the agreed service MTU without unexplained fragmentation, truncation or interworking incompatibility. Confirm this by: Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs.
Incorrect Answers
A:That option concerns VPLS MAC learning flooding and split-horizon safeguards. The related controlled intervention is: Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail.
B:That option concerns PIM dense mode versus sparse mode interface deployment. The related controlled intervention is: Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail.
C:This alternative proposes: A moved customer endpoint is reachable through its current PE and stale advertised paths are withdrawn or updated according to supported mobility behavior. It concerns a different Junos engineering issue EVPN MAC IP route type two control plane and learning, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
Question 435
A Junos routing design reviewer evaluates an unsafe shortcut in this network customer scenario. A wholesale Ethernet service passes small ping frames but drops larger customer frames after Q-in-Q tags and MPLS labels increase actual transmitted size. Which assumption is MOST DIRECTLY dangerous or unsupported? Select ONE best answer.
- Configure one PE for BGP-signaled VPLS and another for unrelated LDP service discovery then assume VLAN IDs alone create a multipoint interconnect.
- Disable all split-horizon checks and bridge every pseudowire to every other pseudowire as a first response to one unknown MAC address.
- Declare a pseudowire healthy based only on an Up connection flag despite large tagged frames being dropped on a transport link with insufficient payload MTU.
- Configure an ingress policer to discard every packet above a tiny burst threshold and claim it is equivalent to lossless queuing under egress shaping.
Explanation
Correct Answer
C:That conflicts with the edge-to-cloud principle: Pseudowire transport can impose encapsulation overhead and require compatible payload/MTU or control-word behavior; signaling Up does not guarantee all customer frame sizes are successfully delivered.
Incorrect Answers
A:This alternative proposes: Configure one PE for BGP-signaled VPLS and another for unrelated LDP service discovery then assume VLAN IDs alone create a multipoint interconnect. It concerns a different Junos engineering issue VPLS service control plane LDP versus BGP distribution, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
B:This alternative proposes: Disable all split-horizon checks and bridge every pseudowire to every other pseudowire as a first response to one unknown MAC address. It concerns a different Junos engineering issue VPLS MAC learning flooding and split-horizon safeguards, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
D:This alternative proposes: Configure an ingress policer to discard every packet above a tiny burst threshold and claim it is equivalent to lossless queuing under egress shaping. It concerns a different Junos engineering issue CoS policers traffic-shaping and committed-rate contracts, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
Question 436
A Junos service-provider routing engineer investigates the following routing and service incident: One PE enables pseudowire control-word handling and the remote PE uses a mismatched expectation, causing otherwise healthy transport to misinterpret payloads. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.
- Verify address-family negotiation and route transport for IPv4 unicast, VPNv4, VPNv6 or EVPN separately rather than treating Established BGP TCP state as proof each family works.
- Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail.
- Trace an LDP Layer 2 circuit end to end using neighbor signaling, pseudowire identifiers and operational connection state before changing customer VLANs.
- Diagnose unknown unicast flooding and Layer 2 loops by distinguishing learned customer MAC paths, BUM handling and VPLS split-horizon behavior.
Explanation
Correct Answer
B:The case-specific routing and services action is: Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail. The governing Junos routing/service principle is: Pseudowire transport can impose encapsulation overhead and require compatible payload/MTU or control-word behavior; signaling Up does not guarantee all customer frame sizes are successfully delivered. Verify the decision through: Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs.
Incorrect Answers
A:This alternative proposes: Verify address-family negotiation and route transport for IPv4 unicast, VPNv4, VPNv6 or EVPN separately rather than treating Established BGP TCP state as proof each family works. It concerns a different Junos engineering issue Multiprotocol BGP family negotiations and VPN routes, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
C:This alternative proposes: Trace an LDP Layer 2 circuit end to end using neighbor signaling, pseudowire identifiers and operational connection state before changing customer VLANs. It concerns a different Junos engineering issue LDP signaled Layer 2 circuit pseudowire status and VC identifiers, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
D:This alternative proposes: Diagnose unknown unicast flooding and Layer 2 loops by distinguishing learned customer MAC paths, BUM handling and VPLS split-horizon behavior. It concerns a different Junos engineering issue VPLS MAC learning flooding and split-horizon safeguards, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
Question 437
A provider routing design review considers this situation. One PE enables pseudowire control-word handling and the remote PE uses a mismatched expectation, causing otherwise healthy transport to misinterpret payloads. A colleague proposes: Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail. Which technical principle BEST supports that action? Select ONE best answer.
- VPLS presents multipoint Ethernet LAN semantics across provider nodes, while LDP or BGP signaling can distribute service state and labels; mixing models requires supported interworking.
- In a typical BGP/MPLS L3VPN, an outer transport label carries traffic toward the egress PE and an inner VPN label selects the egress service context as supported by the implementation.
- Pseudowire transport can impose encapsulation overhead and require compatible payload/MTU or control-word behavior; signaling Up does not guarantee all customer frame sizes are successfully delivered.
- An LDP-signaled pseudowire uses locally and remotely agreed circuit identifiers, transport paths and VC labels; mismatched endpoints or identifiers can prevent service Up state.
Explanation
Correct Answer
C:The relevant Junos service-provider networking principle is: Pseudowire transport can impose encapsulation overhead and require compatible payload/MTU or control-word behavior; signaling Up does not guarantee all customer frame sizes are successfully delivered. In the described provider-network case (One PE enables pseudowire control-word handling and the remote PE uses a mismatched expectation, causing otherwise healthy transport to misinterpret payloads.), it supports the planned action: Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail.
Incorrect Answers
A:This alternative proposes: VPLS presents multipoint Ethernet LAN semantics across provider nodes, while LDP or BGP signaling can distribute service state and labels; mixing models requires supported interworking. It concerns a different Junos engineering issue VPLS service control plane LDP versus BGP distribution, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
B:This alternative proposes: In a typical BGP/MPLS L3VPN, an outer transport label carries traffic toward the egress PE and an inner VPN label selects the egress service context as supported by the implementation. It concerns a different Junos engineering issue MPLS VPN transport label stack and next hop, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
D:This alternative proposes: An LDP-signaled pseudowire uses locally and remotely agreed circuit identifiers, transport paths and VC labels; mismatched endpoints or identifiers can prevent service Up state. It concerns a different Junos engineering issue LDP signaled Layer 2 circuit pseudowire status and VC identifiers, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
Question 438
A Juniper service-provider engineer needs decisive verification evidence for this situation. One PE enables pseudowire control-word handling and the remote PE uses a mismatched expectation, causing otherwise healthy transport to misinterpret payloads. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.
- Inspect IS-IS metric configuration on both ends, extended TLV capability, show isis route, and SPF results before changing costs.
- Inspect show l2circuit connections, LDP session state, neighbor addresses, VC IDs, service-facing interfaces and transport LSP reachability.
- Check service-site IDs, multihoming preference, attachment circuits, signaling reachability, MAC moves and measured forwarding during failover.
- Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs.
Explanation
Correct Answer
D:The direct discriminating observation is: Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs. In the stated situation (One PE enables pseudowire control-word handling and the remote PE uses a mismatched expectation, causing otherwise healthy transport to misinterpret payloads.), the intended acceptance outcome is: The customer transports frames within the agreed service MTU without unexplained fragmentation, truncation or interworking incompatibility.
Incorrect Answers
A:This alternative proposes: Inspect IS-IS metric configuration on both ends, extended TLV capability, show isis route, and SPF results before changing costs. It concerns a different Junos engineering issue IS-IS wide metrics traffic engineering and cost selection, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
B:This alternative proposes: Inspect show l2circuit connections, LDP session state, neighbor addresses, VC IDs, service-facing interfaces and transport LSP reachability. It concerns a different Junos engineering issue LDP signaled Layer 2 circuit pseudowire status and VC identifiers, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
C:This alternative proposes: Check service-site IDs, multihoming preference, attachment circuits, signaling reachability, MAC moves and measured forwarding during failover. It concerns a different Junos engineering issue VPLS site identifiers multihoming and service convergence, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
Question 439
A service-provider acceptance team reviews the result of a provider-service change. One PE enables pseudowire control-word handling and the remote PE uses a mismatched expectation, causing otherwise healthy transport to misinterpret payloads. The intended verification is: Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs. Which outcome BEST demonstrates success? Select ONE best answer.
- A moved customer endpoint is reachable through its current PE and stale advertised paths are withdrawn or updated according to supported mobility behavior.
- The two attachment circuits join only their authorized sites and the pseudowire status and customer traffic counters remain stable.
- Customer multicast subscribers receive their authorized streams through the VPN without flooding other tenants or depending on unavailable default multicast underlay features.
- The customer transports frames within the agreed service MTU without unexplained fragmentation, truncation or interworking incompatibility.
Explanation
Correct Answer
D:The verified success outcome is: The customer transports frames within the agreed service MTU without unexplained fragmentation, truncation or interworking incompatibility. Confirm this by: Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs. The related controlled intervention is: Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail.
Incorrect Answers
A:This alternative proposes: A moved customer endpoint is reachable through its current PE and stale advertised paths are withdrawn or updated according to supported mobility behavior. It concerns a different Junos engineering issue EVPN MAC IP route type two control plane and learning, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
B:This alternative proposes: The two attachment circuits join only their authorized sites and the pseudowire status and customer traffic counters remain stable. It concerns a different Junos engineering issue LDP signaled Layer 2 circuit pseudowire status and VC identifiers, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
C:That option concerns Multicast VPN provider and customer traffic separation. The related controlled intervention is: Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail.
Question 440
A Junos service-provider routing engineer investigates this service-provider network scenario. One PE enables pseudowire control-word handling and the remote PE uses a mismatched expectation, causing otherwise healthy transport to misinterpret payloads. Which TWO complementary steps combine a suitable technical action and its direct verification? Select TWO answers.
- Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
- Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.
- Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs.
- Inspect VPLS instance configuration, signaling session state, remote PE discovery, VPLS route or LDP label distribution and actual MAC reachability.
- Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail.
Explanation
Correct Answers
C:The direct discriminating observation is: Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs.
E:The case-specific routing and services action is: Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail.
Incorrect Answers
A:This alternative proposes: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm. It concerns a different Junos engineering issue IS-IS DIS pseudonode and broadcast circuit election, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
B:This alternative proposes: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access. It concerns a different Junos engineering issue Layer 3 VPN hub spoke topology and controlled Internet breakout, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.
D:This alternative proposes: Inspect VPLS instance configuration, signaling session state, remote PE discovery, VPLS route or LDP label distribution and actual MAC reachability. It concerns a different Junos engineering issue VPLS service control plane LDP versus BGP distribution, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.