cert
cert-1
cert-2

Pass Juniper JN0-664 Exam in First Attempt Guaranteed!

Get 100% Latest Exam Questions, Accurate & Verified Answers to Pass the Actual Exam!
30 Days Free Updates, Instant Download!

cert-5
cert-6
JN0-664 Exam - Verified By Experts
JN0-664 Premium File

JN0-664 Premium File

$69.99
$76.99
  • Premium File 96 Questions & Answers. Last Update: Nov 19, 2026

Whats Included:

  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
 
$76.99
$69.99
accept 20 downloads in the last 7 days
block-screenshots
Juniper JN0-664 Practice Test 45

Question 440

A Junos service-provider routing engineer investigates this service-provider network scenario. One PE enables pseudowire control-word handling and the remote PE uses a mismatched expectation, causing otherwise healthy transport to misinterpret payloads. Which TWO complementary steps combine a suitable technical action and its direct verification? Select TWO answers.

  1. Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm.
  2. Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.
  3. Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs.
  4. Inspect VPLS instance configuration, signaling session state, remote PE discovery, VPLS route or LDP label distribution and actual MAC reachability.
  5. Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail.

Explanation

Correct Answers

C:

The direct discriminating observation is: Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs.

E:

The case-specific routing and services action is: Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail.

Incorrect Answers

A:

This alternative proposes: Validate Designated Intermediate System behavior on a LAN segment rather than confusing it with the OSPF DR/BDR algorithm. It concerns a different Junos engineering issue IS-IS DIS pseudonode and broadcast circuit election, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.

B:

This alternative proposes: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access. It concerns a different Junos engineering issue Layer 3 VPN hub spoke topology and controlled Internet breakout, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.

D:

This alternative proposes: Inspect VPLS instance configuration, signaling session state, remote PE discovery, VPLS route or LDP label distribution and actual MAC reachability. It concerns a different Junos engineering issue VPLS service control plane LDP versus BGP distribution, not the directly tested provider-network issue Layer 2 pseudowire MTU and control-word interworking.

Question 441

A Junos service-provider routing engineer investigates the following routing and service incident: Two edge nodes can ping each other's loopbacks but their BGP Layer 2 VPN never comes Up because the required signaling family was not negotiated. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.

  1. Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail.
  2. Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings.
  3. Plan VPLS multihoming with supported service site identifiers, redundancy roles and failover controls to avoid a duplicate active attachment loop.
  4. Confirm appropriate PIM sparse-mode RP reachability and registration for any-source multicast groups before treating receiver membership as full service health.

Explanation

Correct Answer

B:

The case-specific routing and services action is: Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings. The governing Junos routing/service principle is: A BGP-signaled Layer 2 VPN advertises service-related NLRI and label reachability; route-target and instance-policy behavior determine which remote service participates.

Incorrect Answers

A:

This alternative proposes: Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail. It concerns a different Junos engineering issue Layer 2 pseudowire MTU and control-word interworking, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

C:

This alternative proposes: Plan VPLS multihoming with supported service site identifiers, redundancy roles and failover controls to avoid a duplicate active attachment loop. It concerns a different Junos engineering issue VPLS site identifiers multihoming and service convergence, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

D:

This alternative proposes: Confirm appropriate PIM sparse-mode RP reachability and registration for any-source multicast groups before treating receiver membership as full service health. It concerns a different Junos engineering issue PIM sparse mode rendezvous point and shared tree operation, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

Question 442

A provider routing design review considers this situation. Two edge nodes can ping each other's loopbacks but their BGP Layer 2 VPN never comes Up because the required signaling family was not negotiated. A colleague proposes: Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings. Which technical principle BEST supports that action? Select ONE best answer.

  1. EVPN all-active or single-active multihoming uses a shared ESI and appropriate DF/aliasing coordination to prevent BUM duplication and maintain reachable paths under failure.
  2. A BGP-signaled Layer 2 VPN advertises service-related NLRI and label reachability; route-target and instance-policy behavior determine which remote service participates.
  3. Pseudowire transport can impose encapsulation overhead and require compatible payload/MTU or control-word behavior; signaling Up does not guarantee all customer frame sizes are successfully delivered.
  4. Junos routing policies match routes and apply actions at protocol boundaries; match order, accept/reject and explicit default behavior determine effective advertisements.

Explanation

Correct Answer

B:

The relevant Junos service-provider networking principle is: A BGP-signaled Layer 2 VPN advertises service-related NLRI and label reachability; route-target and instance-policy behavior determine which remote service participates. In the described provider-network case (Two edge nodes can ping each other's loopbacks but their BGP Layer 2 VPN never comes Up because the required signaling family was not negotiated.), it supports the planned action: Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings.

Incorrect Answers

A:

This alternative proposes: EVPN all-active or single-active multihoming uses a shared ESI and appropriate DF/aliasing coordination to prevent BUM duplication and maintain reachable paths under failure. It concerns a different Junos engineering issue EVPN Ethernet segment multihoming and designated forwarder, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

C:

This alternative proposes: Pseudowire transport can impose encapsulation overhead and require compatible payload/MTU or control-word behavior; signaling Up does not guarantee all customer frame sizes are successfully delivered. It concerns a different Junos engineering issue Layer 2 pseudowire MTU and control-word interworking, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

D:

This alternative proposes: Junos routing policies match routes and apply actions at protocol boundaries; match order, accept/reject and explicit default behavior determine effective advertisements. It concerns a different Junos engineering issue BGP export import policy and prefix controls, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

Question 443

A Juniper service-provider engineer needs decisive verification evidence for this situation. Two edge nodes can ping each other's loopbacks but their BGP Layer 2 VPN never comes Up because the required signaling family was not negotiated. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.

  1. Check service-site IDs, multihoming preference, attachment circuits, signaling reachability, MAC moves and measured forwarding during failover.
  2. Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs.
  3. Review show configuration policy-options, protocol group policy attachments, route advertisements, route receive output and active versus hidden state.
  4. Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state.

Explanation

Correct Answer

D:

The direct discriminating observation is: Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state. In the stated situation (Two edge nodes can ping each other's loopbacks but their BGP Layer 2 VPN never comes Up because the required signaling family was not negotiated.), the intended acceptance outcome is: The appropriate PEs establish only the requested customer Layer 2 connections and do not merge different customer switching domains.

Incorrect Answers

A:

This alternative proposes: Check service-site IDs, multihoming preference, attachment circuits, signaling reachability, MAC moves and measured forwarding during failover. It concerns a different Junos engineering issue VPLS site identifiers multihoming and service convergence, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

B:

This alternative proposes: Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs. It concerns a different Junos engineering issue Layer 2 pseudowire MTU and control-word interworking, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

C:

This alternative proposes: Review show configuration policy-options, protocol group policy attachments, route advertisements, route receive output and active versus hidden state. It concerns a different Junos engineering issue BGP export import policy and prefix controls, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

Question 444

A service-provider acceptance team reviews the result of a provider-service change. Two edge nodes can ping each other's loopbacks but their BGP Layer 2 VPN never comes Up because the required signaling family was not negotiated. The intended verification is: Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state. Which outcome BEST demonstrates success? Select ONE best answer.

  1. Participating customer sites exchange permitted Ethernet frames through a correctly signaled multipoint service without bridging unrelated tenants.
  2. The configured mode serves actual receivers without uncontrolled multicast flood in sparsely subscribed provider regions.
  3. The authorized CE service survives a primary PE outage with the expected alternate active and without creating duplicated Ethernet forwarding.
  4. The appropriate PEs establish only the requested customer Layer 2 connections and do not merge different customer switching domains.

Explanation

Correct Answer

D:

The verified success outcome is: The appropriate PEs establish only the requested customer Layer 2 connections and do not merge different customer switching domains. Confirm this by: Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state.

Incorrect Answers

A:

That option concerns VPLS service control plane LDP versus BGP distribution. The related controlled intervention is: Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings.

B:

That option concerns PIM dense mode versus sparse mode interface deployment. The related controlled intervention is: Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings.

C:

This alternative proposes: The authorized CE service survives a primary PE outage with the expected alternate active and without creating duplicated Ethernet forwarding. It concerns a different Junos engineering issue VPLS site identifiers multihoming and service convergence, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

Question 445

A Junos routing design reviewer evaluates an unsafe shortcut in this network customer scenario. Two edge nodes can ping each other's loopbacks but their BGP Layer 2 VPN never comes Up because the required signaling family was not negotiated. Which assumption is MOST DIRECTLY dangerous or unsupported? Select ONE best answer.

  1. Declare a pseudowire healthy based only on an Up connection flag despite large tagged frames being dropped on a transport link with insufficient payload MTU.
  2. Assume an Established IPv4-unicast-only BGP session automatically distributes BGP Layer 2 VPN NLRI and labels to every PE.
  3. Assume a core link with more bandwidth automatically has the lowest IS-IS metric when no operator metric policy has been configured.
  4. Assume every MAC learned on an EVPN remote PE must be discovered exclusively by data-plane flood without any BGP MAC/IP advertisement.

Explanation

Correct Answer

B:

That conflicts with the edge-to-cloud principle: A BGP-signaled Layer 2 VPN advertises service-related NLRI and label reachability; route-target and instance-policy behavior determine which remote service participates.

Incorrect Answers

A:

This alternative proposes: Declare a pseudowire healthy based only on an Up connection flag despite large tagged frames being dropped on a transport link with insufficient payload MTU. It concerns a different Junos engineering issue Layer 2 pseudowire MTU and control-word interworking, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

C:

This alternative proposes: Assume a core link with more bandwidth automatically has the lowest IS-IS metric when no operator metric policy has been configured. It concerns a different Junos engineering issue IS-IS wide metrics traffic engineering and cost selection, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

D:

This alternative proposes: Assume every MAC learned on an EVPN remote PE must be discovered exclusively by data-plane flood without any BGP MAC/IP advertisement. It concerns a different Junos engineering issue EVPN MAC IP route type two control plane and learning, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

Question 446

A Junos service-provider routing engineer investigates the following routing and service incident: A customer circuit's BGP service route is received on a remote PE but is excluded from the correct instance by a route-target import mismatch. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.

  1. Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings.
  2. Use reverse-path forwarding checks to determine why an arriving multicast packet is accepted on one interface but discarded on another.
  3. Trace an LDP Layer 2 circuit end to end using neighbor signaling, pseudowire identifiers and operational connection state before changing customer VLANs.
  4. Plan VPLS multihoming with supported service site identifiers, redundancy roles and failover controls to avoid a duplicate active attachment loop.

Explanation

Correct Answer

A:

The case-specific routing and services action is: Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings. The governing Junos routing/service principle is: A BGP-signaled Layer 2 VPN advertises service-related NLRI and label reachability; route-target and instance-policy behavior determine which remote service participates. Verify the decision through: Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state.

Incorrect Answers

B:

This alternative proposes: Use reverse-path forwarding checks to determine why an arriving multicast packet is accepted on one interface but discarded on another. It concerns a different Junos engineering issue Multicast RPF validation and source reachability, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

C:

This alternative proposes: Trace an LDP Layer 2 circuit end to end using neighbor signaling, pseudowire identifiers and operational connection state before changing customer VLANs. It concerns a different Junos engineering issue LDP signaled Layer 2 circuit pseudowire status and VC identifiers, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

D:

This alternative proposes: Plan VPLS multihoming with supported service site identifiers, redundancy roles and failover controls to avoid a duplicate active attachment loop. It concerns a different Junos engineering issue VPLS site identifiers multihoming and service convergence, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

Question 447

A provider routing design review considers this situation. A customer circuit's BGP service route is received on a remote PE but is excluded from the correct instance by a route-target import mismatch. A colleague proposes: Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings. Which technical principle BEST supports that action? Select ONE best answer.

  1. EVPN all-active or single-active multihoming uses a shared ESI and appropriate DF/aliasing coordination to prevent BUM duplication and maintain reachable paths under failure.
  2. A BGP-signaled Layer 2 VPN advertises service-related NLRI and label reachability; route-target and instance-policy behavior determine which remote service participates.
  3. IS-IS uses LSPs to distribute link-state topology and SNP mechanisms to synchronize databases; incomplete flooding can leave routers computing different SPF paths.
  4. VPLS site identification and multihoming mechanisms help coordinate PE access, but customer-facing redundant paths need a supported convergence and loop-control design.

Explanation

Correct Answer

B:

The relevant Junos service-provider networking principle is: A BGP-signaled Layer 2 VPN advertises service-related NLRI and label reachability; route-target and instance-policy behavior determine which remote service participates. In the described provider-network case (A customer circuit's BGP service route is received on a remote PE but is excluded from the correct instance by a route-target import mismatch.), it supports the planned action: Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings.

Incorrect Answers

A:

This alternative proposes: EVPN all-active or single-active multihoming uses a shared ESI and appropriate DF/aliasing coordination to prevent BUM duplication and maintain reachable paths under failure. It concerns a different Junos engineering issue EVPN Ethernet segment multihoming and designated forwarder, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

C:

This alternative proposes: IS-IS uses LSPs to distribute link-state topology and SNP mechanisms to synchronize databases; incomplete flooding can leave routers computing different SPF paths. It concerns a different Junos engineering issue IS-IS link-state packet flooding and database consistency, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

D:

This alternative proposes: VPLS site identification and multihoming mechanisms help coordinate PE access, but customer-facing redundant paths need a supported convergence and loop-control design. It concerns a different Junos engineering issue VPLS site identifiers multihoming and service convergence, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

Question 448

A Juniper service-provider engineer needs decisive verification evidence for this situation. A customer circuit's BGP service route is received on a remote PE but is excluded from the correct instance by a route-target import mismatch. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.

  1. Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state.
  2. Inspect show route table bgp.l3vpn.0, instance.inet.0, accepted RT communities, next-hop resolution and label information at both PEs.
  3. Inspect Ethernet segment configuration, ESI values, DF election or relevant designated-forwarder state, ES routes, BGP reachability and measured failover forwarding.
  4. Inspect show l2circuit connections, LDP session state, neighbor addresses, VC IDs, service-facing interfaces and transport LSP reachability.

Explanation

Correct Answer

A:

The direct discriminating observation is: Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state. In the stated situation (A customer circuit's BGP service route is received on a remote PE but is excluded from the correct instance by a route-target import mismatch.), the intended acceptance outcome is: The appropriate PEs establish only the requested customer Layer 2 connections and do not merge different customer switching domains.

Incorrect Answers

B:

This alternative proposes: Inspect show route table bgp.l3vpn.0, instance.inet.0, accepted RT communities, next-hop resolution and label information at both PEs. It concerns a different Junos engineering issue VPNv4 bgp.l3vpn.0 versus customer VRF route tables, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import in the stated situation (A customer circuit's BGP service route is received on a remote PE but is excluded from the correct instance by a route-target import mismatch.). A better case-specific check is: Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state. The more targeted action is: Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings.

C:

This alternative proposes: Inspect Ethernet segment configuration, ESI values, DF election or relevant designated-forwarder state, ES routes, BGP reachability and measured failover forwarding. It concerns a different Junos engineering issue EVPN Ethernet segment multihoming and designated forwarder, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

D:

This alternative proposes: Inspect show l2circuit connections, LDP session state, neighbor addresses, VC IDs, service-facing interfaces and transport LSP reachability. It concerns a different Junos engineering issue LDP signaled Layer 2 circuit pseudowire status and VC identifiers, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

Question 449

A service-provider acceptance team reviews the result of a provider-service change. A customer circuit's BGP service route is received on a remote PE but is excluded from the correct instance by a route-target import mismatch. The intended verification is: Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state. Which outcome BEST demonstrates success? Select ONE best answer.

  1. Clients receive authorized routes without a full iBGP mesh and no reflected route loops or unreachable forwarding next hops develop.
  2. The appropriate PEs establish only the requested customer Layer 2 connections and do not merge different customer switching domains.
  3. The authorized CE service survives a primary PE outage with the expected alternate active and without creating duplicated Ethernet forwarding.
  4. The two attachment circuits join only their authorized sites and the pseudowire status and customer traffic counters remain stable.

Explanation

Correct Answer

B:

The verified success outcome is: The appropriate PEs establish only the requested customer Layer 2 connections and do not merge different customer switching domains. Confirm this by: Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state. The related controlled intervention is: Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings.

Incorrect Answers

A:

This alternative proposes: Clients receive authorized routes without a full iBGP mesh and no reflected route loops or unreachable forwarding next hops develop. It concerns a different Junos engineering issue BGP route reflectors originator and cluster loop prevention, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

C:

This alternative proposes: The authorized CE service survives a primary PE outage with the expected alternate active and without creating duplicated Ethernet forwarding. It concerns a different Junos engineering issue VPLS site identifiers multihoming and service convergence, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

D:

That option concerns LDP signaled Layer 2 circuit pseudowire status and VC identifiers. The related controlled intervention is: Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings.

Question 450

A Junos service-provider routing engineer investigates this service-provider network scenario. A customer circuit's BGP service route is received on a remote PE but is excluded from the correct instance by a route-target import mismatch. Which TWO complementary steps combine a suitable technical action and its direct verification? Select TWO answers.

  1. Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state.
  2. Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings.
  3. Check service-site IDs, multihoming preference, attachment circuits, signaling reachability, MAC moves and measured forwarding during failover.
  4. Classify subscriber traffic with an appropriate behavior-aggregate or multifield classifier and confirm forwarding-class assignments at ingress.
  5. Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone.

Explanation

Correct Answers

A:

The direct discriminating observation is: Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state.

B:

The case-specific routing and services action is: Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings.

Incorrect Answers

C:

This alternative proposes: Check service-site IDs, multihoming preference, attachment circuits, signaling reachability, MAC moves and measured forwarding during failover. It concerns a different Junos engineering issue VPLS site identifiers multihoming and service convergence, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

D:

This alternative proposes: Classify subscriber traffic with an appropriate behavior-aggregate or multifield classifier and confirm forwarding-class assignments at ingress. It concerns a different Junos engineering issue Junos CoS behavior aggregate versus multifield classifiers, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

E:

This alternative proposes: Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone. It concerns a different Junos engineering issue Multicast VPN provider and customer traffic separation, not the directly tested provider-network issue BGP-signaled Layer 2 VPN NLRI and route target import.

Service Provider Routing and Switching, Professional (JNCIP-SP) (JN0-664) Practice Tests