Juniper JN0-664 Practice Test 42
Question 410
A Junos routing design reviewer evaluates an unsafe shortcut in this network customer scenario. A remote PE receives IPv6 VPN NLRI but the subscriber VRF has no instance.inet6.0 route because the corresponding RT import policy is missing. Which assumption is MOST DIRECTLY dangerous or unsupported? Select ONE best answer.
- Import every spoke RT into all customer VRFs when the design explicitly requires isolation except for a controlled central inspection service.
- Enable MP-BGP VPN unicast for a tenant and promise its source multicast group will automatically traverse provider PEs with no MVPN or multicast setup.
- Assume every MAC learned on an EVPN remote PE must be discovered exclusively by data-plane flood without any BGP MAC/IP advertisement.
- Assume an established VPNv4 BGP session automatically advertises the IPv6 prefix 2001:db8:50::/48 into every remote instance.inet6.0.
Explanation
Correct Answer
D:That conflicts with the edge-to-cloud principle: IPv6 Layer 3 VPN routes use address-family-specific control-plane and forwarding information; a working IPv4 tenant VRF does not itself establish IPv6 connectivity.
Incorrect Answers
A:This alternative proposes: Import every spoke RT into all customer VRFs when the design explicitly requires isolation except for a controlled central inspection service. It concerns a different Junos engineering issue Layer 3 VPN hub spoke topology and controlled Internet breakout, not the directly tested provider-network issue IPv6 Layer 3 VPN VPNv6 route families and forwarding.
B:This alternative proposes: Enable MP-BGP VPN unicast for a tenant and promise its source multicast group will automatically traverse provider PEs with no MVPN or multicast setup. It concerns a different Junos engineering issue Multicast VPN provider and customer traffic separation, not the directly tested provider-network issue IPv6 Layer 3 VPN VPNv6 route families and forwarding.
C:This alternative proposes: Assume every MAC learned on an EVPN remote PE must be discovered exclusively by data-plane flood without any BGP MAC/IP advertisement. It concerns a different Junos engineering issue EVPN MAC IP route type two control plane and learning, not the directly tested provider-network issue IPv6 Layer 3 VPN VPNv6 route families and forwarding.
Question 411
A Junos service-provider routing engineer investigates the following routing and service incident: A media tenant can ping remote CE interfaces over its L3VPN but video packets never arrive because multicast state and transport were not established. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.
- Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies.
- Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone.
- Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
- Configure a scheduler map for the intended egress forwarding classes and verify bandwidth, buffer and priority behavior during real congestion.
Explanation
Correct Answer
B:The case-specific routing and services action is: Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone. The governing Junos routing/service principle is: MVPN carries customer multicast across provider networks using supported control-plane membership and provider transport mechanisms; unicast VRF reachability alone does not prove multicast distribution.
Incorrect Answers
A:This alternative proposes: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies. It concerns a different Junos engineering issue Layer 3 VPN route distinguishers versus route targets, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
C:This alternative proposes: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection. It concerns a different Junos engineering issue Site of Origin and OSPF sham-link loop control, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
D:This alternative proposes: Configure a scheduler map for the intended egress forwarding classes and verify bandwidth, buffer and priority behavior during real congestion. It concerns a different Junos engineering issue CoS schedulers scheduler-maps and bandwidth sharing, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
Question 412
A provider routing design review considers this situation. A media tenant can ping remote CE interfaces over its L3VPN but video packets never arrive because multicast state and transport were not established. A colleague proposes: Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone. Which technical principle BEST supports that action? Select ONE best answer.
- In a typical BGP/MPLS L3VPN, an outer transport label carries traffic toward the egress PE and an inner VPN label selects the egress service context as supported by the implementation.
- Multicast RPF checks the expected upstream interface toward the source using relevant routing information; correct downstream membership cannot compensate for a failed upstream RPF check.
- MVPN carries customer multicast across provider networks using supported control-plane membership and provider transport mechanisms; unicast VRF reachability alone does not prove multicast distribution.
- IPv6 Layer 3 VPN routes use address-family-specific control-plane and forwarding information; a working IPv4 tenant VRF does not itself establish IPv6 connectivity.
Explanation
Correct Answer
C:The relevant Junos service-provider networking principle is: MVPN carries customer multicast across provider networks using supported control-plane membership and provider transport mechanisms; unicast VRF reachability alone does not prove multicast distribution. In the described provider-network case (A media tenant can ping remote CE interfaces over its L3VPN but video packets never arrive because multicast state and transport were not established.), it supports the planned action: Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone.
Incorrect Answers
A:This alternative proposes: In a typical BGP/MPLS L3VPN, an outer transport label carries traffic toward the egress PE and an inner VPN label selects the egress service context as supported by the implementation. It concerns a different Junos engineering issue MPLS VPN transport label stack and next hop, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
B:This alternative proposes: Multicast RPF checks the expected upstream interface toward the source using relevant routing information; correct downstream membership cannot compensate for a failed upstream RPF check. It concerns a different Junos engineering issue Multicast RPF validation and source reachability, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
D:This alternative proposes: IPv6 Layer 3 VPN routes use address-family-specific control-plane and forwarding information; a working IPv4 tenant VRF does not itself establish IPv6 connectivity. It concerns a different Junos engineering issue IPv6 Layer 3 VPN VPNv6 route families and forwarding, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
Question 413
A Juniper service-provider engineer needs decisive verification evidence for this situation. A media tenant can ping remote CE interfaces over its L3VPN but video packets never arrive because multicast state and transport were not established. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.
- Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding.
- Inspect show bgp neighbor advertised/received family capabilities, relevant family statements, VPN/EVPN route tables, route-target policy and next-hop reachability.
- Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population.
- Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy.
Explanation
Correct Answer
A:The direct discriminating observation is: Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding. In the stated situation (A media tenant can ping remote CE interfaces over its L3VPN but video packets never arrive because multicast state and transport were not established.), the intended acceptance outcome is: Customer multicast subscribers receive their authorized streams through the VPN without flooding other tenants or depending on unavailable default multicast underlay features.
Incorrect Answers
B:This alternative proposes: Inspect show bgp neighbor advertised/received family capabilities, relevant family statements, VPN/EVPN route tables, route-target policy and next-hop reachability. It concerns a different Junos engineering issue Multiprotocol BGP family negotiations and VPN routes, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
C:This alternative proposes: Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population. It concerns a different Junos engineering issue Layer 3 VPN route distinguishers versus route targets, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
D:This alternative proposes: Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy. It concerns a different Junos engineering issue Site of Origin and OSPF sham-link loop control, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
Question 414
A service-provider acceptance team reviews the result of a provider-service change. A media tenant can ping remote CE interfaces over its L3VPN but video packets never arrive because multicast state and transport were not established. The intended verification is: Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding. Which outcome BEST demonstrates success? Select ONE best answer.
- The intended remote VPN site can reach its authorized peer across the AS boundary without transferring unrelated tenants' routes or losing required label resolution.
- Authorized IPv6 subnets communicate across customer sites while overlapping IPv4 tenant routing remains isolated and unchanged.
- The customer contract rate is enforced with predictable handling of permitted bursts and no unintended control-plane traffic drops.
- Customer multicast subscribers receive their authorized streams through the VPN without flooding other tenants or depending on unavailable default multicast underlay features.
Explanation
Correct Answer
D:The verified success outcome is: Customer multicast subscribers receive their authorized streams through the VPN without flooding other tenants or depending on unavailable default multicast underlay features. Confirm this by: Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding.
Incorrect Answers
A:This alternative proposes: The intended remote VPN site can reach its authorized peer across the AS boundary without transferring unrelated tenants' routes or losing required label resolution. It concerns a different Junos engineering issue Interprovider Layer 3 VPN options and carrier of carriers, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
B:That option concerns IPv6 Layer 3 VPN VPNv6 route families and forwarding. The related controlled intervention is: Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone.
C:That option concerns CoS policers traffic-shaping and committed-rate contracts. The related controlled intervention is: Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone.
Question 415
A Junos service-provider routing engineer investigates this service-provider network scenario. A media tenant can ping remote CE interfaces over its L3VPN but video packets never arrive because multicast state and transport were not established. Which TWO complementary steps combine a suitable technical action and its direct verification? Select TWO answers.
- Confirm appropriate PIM sparse-mode RP reachability and registration for any-source multicast groups before treating receiver membership as full service health.
- Choose a supported VPLS signaling model and verify peer discovery, service membership and MPLS forwarding transport independently.
- Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy.
- Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding.
- Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone.
Explanation
Correct Answers
D:The direct discriminating observation is: Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding.
E:The case-specific routing and services action is: Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone. The governing Junos routing/service principle is: MVPN carries customer multicast across provider networks using supported control-plane membership and provider transport mechanisms; unicast VRF reachability alone does not prove multicast distribution. Verify the decision through: Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding.
Incorrect Answers
A:This alternative proposes: Confirm appropriate PIM sparse-mode RP reachability and registration for any-source multicast groups before treating receiver membership as full service health. It concerns a different Junos engineering issue PIM sparse mode rendezvous point and shared tree operation, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
B:This alternative proposes: Choose a supported VPLS signaling model and verify peer discovery, service membership and MPLS forwarding transport independently. It concerns a different Junos engineering issue VPLS service control plane LDP versus BGP distribution, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
C:This alternative proposes: Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy. It concerns a different Junos engineering issue Site of Origin and OSPF sham-link loop control, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation in the stated situation (A media tenant can ping remote CE interfaces over its L3VPN but video packets never arrive because multicast state and transport were not established.). A better case-specific check is: Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding.
Question 416
A Junos service-provider routing engineer investigates the following routing and service incident: A provider mistakenly imports an MVPN customer group's traffic into another VRF and must restore per-tenant multicast isolation while keeping authorized streams active. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.
- Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone.
- Verify the transport and service label roles in an MPLS Layer 3 VPN before attributing a forwarding failure to the customer routing protocol.
- Trace a VPNv4 prefix from MP-BGP reception to a customer VRF routing table, distinguishing provider VPN control-plane storage and installed customer forwarding routes.
- Restrict interlevel IS-IS route advertisements to the intended prefixes with controlled L1/L2 policy and verify return reachability.
Explanation
Correct Answer
A:The case-specific routing and services action is: Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone.
Incorrect Answers
B:This alternative proposes: Verify the transport and service label roles in an MPLS Layer 3 VPN before attributing a forwarding failure to the customer routing protocol. It concerns a different Junos engineering issue MPLS VPN transport label stack and next hop, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
C:This alternative proposes: Trace a VPNv4 prefix from MP-BGP reception to a customer VRF routing table, distinguishing provider VPN control-plane storage and installed customer forwarding routes. It concerns a different Junos engineering issue VPNv4 bgp.l3vpn.0 versus customer VRF route tables, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
D:This alternative proposes: Restrict interlevel IS-IS route advertisements to the intended prefixes with controlled L1/L2 policy and verify return reachability. It concerns a different Junos engineering issue IS-IS Level 2 to Level 1 route leaking and summaries, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
Question 417
A provider routing design review considers this situation. A provider mistakenly imports an MVPN customer group's traffic into another VRF and must restore per-tenant multicast isolation while keeping authorized streams active. A colleague proposes: Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone. Which technical principle BEST supports that action? Select ONE best answer.
- Route reflectors relax the default prohibition against propagating iBGP-learned routes to other iBGP peers, with originator and cluster attributes limiting reflection loops.
- SoO identifies the originating customer site for policy-based loop prevention; OSPF sham links can influence customer OSPF path choice across the VPN backbone in particular backdoor-link designs.
- MVPN carries customer multicast across provider networks using supported control-plane membership and provider transport mechanisms; unicast VRF reachability alone does not prove multicast distribution.
- Interprovider options vary in whether adjacent ASBRs exchange VRF routes or labeled VPN/transport routes; carrier-of-carriers provides specialized labeled connectivity, not free unrestricted access.
Explanation
Correct Answer
C:The relevant Junos service-provider networking principle is: MVPN carries customer multicast across provider networks using supported control-plane membership and provider transport mechanisms; unicast VRF reachability alone does not prove multicast distribution. In the described provider-network case (A provider mistakenly imports an MVPN customer group's traffic into another VRF and must restore per-tenant multicast isolation while keeping authorized streams active.), it supports the planned action: Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone.
Incorrect Answers
A:This alternative proposes: Route reflectors relax the default prohibition against propagating iBGP-learned routes to other iBGP peers, with originator and cluster attributes limiting reflection loops. It concerns a different Junos engineering issue BGP route reflectors originator and cluster loop prevention, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
B:This alternative proposes: SoO identifies the originating customer site for policy-based loop prevention; OSPF sham links can influence customer OSPF path choice across the VPN backbone in particular backdoor-link designs. It concerns a different Junos engineering issue Site of Origin and OSPF sham-link loop control, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
D:This alternative proposes: Interprovider options vary in whether adjacent ASBRs exchange VRF routes or labeled VPN/transport routes; carrier-of-carriers provides specialized labeled connectivity, not free unrestricted access. It concerns a different Junos engineering issue Interprovider Layer 3 VPN options and carrier of carriers, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
Question 418
A Juniper service-provider engineer needs decisive verification evidence for this situation. A provider mistakenly imports an MVPN customer group's traffic into another VRF and must restore per-tenant multicast isolation while keeping authorized streams active. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.
- Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding.
- Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state.
- Inspect VPN route label, resolved tunnel in inet.3, label-switched path, control-plane next hop, penultimate-hop behavior and egress VRF lookup.
- Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries.
Explanation
Correct Answer
A:The direct discriminating observation is: Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding. In the stated situation (A provider mistakenly imports an MVPN customer group's traffic into another VRF and must restore per-tenant multicast isolation while keeping authorized streams active.), the intended acceptance outcome is: Customer multicast subscribers receive their authorized streams through the VPN without flooding other tenants or depending on unavailable default multicast underlay features.
Incorrect Answers
B:This alternative proposes: Inspect BGP family negotiation, received Layer 2 VPN routes, RD/RT communities, service site identifiers, label mapping and per-instance state. It concerns a different Junos engineering issue BGP-signaled Layer 2 VPN NLRI and route target import, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
C:This alternative proposes: Inspect VPN route label, resolved tunnel in inet.3, label-switched path, control-plane next hop, penultimate-hop behavior and egress VRF lookup. It concerns a different Junos engineering issue MPLS VPN transport label stack and next hop, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
D:This alternative proposes: Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries. It concerns a different Junos engineering issue Layer 3 VPN hub spoke topology and controlled Internet breakout, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
Question 419
A service-provider acceptance team reviews the result of a provider-service change. A provider mistakenly imports an MVPN customer group's traffic into another VRF and must restore per-tenant multicast isolation while keeping authorized streams active. The intended verification is: Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding. Which outcome BEST demonstrates success? Select ONE best answer.
- The approved egress wins for the expected prefix for documented policy reasons, with a valid alternate when the preferred transit fails.
- Customer multicast subscribers receive their authorized streams through the VPN without flooding other tenants or depending on unavailable default multicast underlay features.
- The ingress PE pushes an appropriate label stack and the egress PE forwards the packet in the authorized customer context without exposing traffic to another VPN.
- The intended remote VPN site can reach its authorized peer across the AS boundary without transferring unrelated tenants' routes or losing required label resolution.
Explanation
Correct Answer
B:The verified success outcome is: Customer multicast subscribers receive their authorized streams through the VPN without flooding other tenants or depending on unavailable default multicast underlay features. Confirm this by: Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding. The related controlled intervention is: Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone.
Incorrect Answers
A:That option concerns BGP best-path attributes and local preference. The related controlled intervention is: Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone.
C:This alternative proposes: The ingress PE pushes an appropriate label stack and the egress PE forwards the packet in the authorized customer context without exposing traffic to another VPN. It concerns a different Junos engineering issue MPLS VPN transport label stack and next hop, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
D:This alternative proposes: The intended remote VPN site can reach its authorized peer across the AS boundary without transferring unrelated tenants' routes or losing required label resolution. It concerns a different Junos engineering issue Interprovider Layer 3 VPN options and carrier of carriers, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
Question 420
A Junos routing design reviewer evaluates an unsafe shortcut in this network customer scenario. A provider mistakenly imports an MVPN customer group's traffic into another VRF and must restore per-tenant multicast isolation while keeping authorized streams active. Which assumption is MOST DIRECTLY dangerous or unsupported? Select ONE best answer.
- Treat an RD as an access-control filter and set identical RDs for every unrelated VPN while leaving permissive RT import policy unrestricted.
- Assume every MAC learned on an EVPN remote PE must be discovered exclusively by data-plane flood without any BGP MAC/IP advertisement.
- Enable MP-BGP VPN unicast for a tenant and promise its source multicast group will automatically traverse provider PEs with no MVPN or multicast setup.
- Assume an established VPNv4 BGP session automatically advertises the IPv6 prefix 2001:db8:50::/48 into every remote instance.inet6.0.
Explanation
Correct Answer
C:That conflicts with the edge-to-cloud principle: MVPN carries customer multicast across provider networks using supported control-plane membership and provider transport mechanisms; unicast VRF reachability alone does not prove multicast distribution.
Incorrect Answers
A:This alternative proposes: Treat an RD as an access-control filter and set identical RDs for every unrelated VPN while leaving permissive RT import policy unrestricted. It concerns a different Junos engineering issue Layer 3 VPN route distinguishers versus route targets, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
B:This alternative proposes: Assume every MAC learned on an EVPN remote PE must be discovered exclusively by data-plane flood without any BGP MAC/IP advertisement. It concerns a different Junos engineering issue EVPN MAC IP route type two control plane and learning, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.
D:This alternative proposes: Assume an established VPNv4 BGP session automatically advertises the IPv6 prefix 2001:db8:50::/48 into every remote instance.inet6.0. It concerns a different Junos engineering issue IPv6 Layer 3 VPN VPNv6 route families and forwarding, not the directly tested provider-network issue Multicast VPN provider and customer traffic separation.