Juniper JN0-664 Practice Test 34
Question 330
A Junos service-provider routing engineer investigates this service-provider network scenario. An ISP changes multicast routing policy during an RP maintenance event, accidentally suppressing one valid customer group while unrelated groups stay healthy. Which TWO complementary steps combine a suitable technical action and its direct verification? Select TWO answers.
- Compare protocol mode on all transit interfaces, show pim interfaces/neighbors, joins or pruning state, multicast flow and CPU/link exposure.
- Apply explicit import and export routing-policy terms to control which customer or upstream prefixes enter the provider BGP routing domain.
- Inspect RP node reachability, anycast route advertisement, appropriate state synchronization, peer status, group registration and service traffic during failover.
- Build resilient ASM rendezvous-point service using supported Anycast RP design and validate source and receiver registration continuity under failover.
- Validate that all nonbackbone OSPF areas have a supported logical connection to area 0, and use virtual links only as a documented transitional design.
Explanation
Correct Answers
C:The direct discriminating observation is: Inspect RP node reachability, anycast route advertisement, appropriate state synchronization, peer status, group registration and service traffic during failover.
D:The case-specific routing and services action is: Build resilient ASM rendezvous-point service using supported Anycast RP design and validate source and receiver registration continuity under failover. The governing Junos routing/service principle is: Anycast RP can let multiple RPs share an RP address with protocol mechanisms to coordinate state, but a reachable shared address alone does not prove group information is synchronized. Verify the decision through: Inspect RP node reachability, anycast route advertisement, appropriate state synchronization, peer status, group registration and service traffic during failover.
Incorrect Answers
A:This alternative proposes: Compare protocol mode on all transit interfaces, show pim interfaces/neighbors, joins or pruning state, multicast flow and CPU/link exposure. It concerns a different Junos engineering issue PIM dense mode versus sparse mode interface deployment, not the directly tested provider-network issue Anycast RP resilient multicast service and routing policy in the stated situation (An ISP changes multicast routing policy during an RP maintenance event, accidentally suppressing one valid customer group while unrelated groups stay healthy.). A better case-specific check is: Inspect RP node reachability, anycast route advertisement, appropriate state synchronization, peer status, group registration and service traffic during failover.
B:This alternative proposes: Apply explicit import and export routing-policy terms to control which customer or upstream prefixes enter the provider BGP routing domain. It concerns a different Junos engineering issue BGP export import policy and prefix controls, not the directly tested provider-network issue Anycast RP resilient multicast service and routing policy.
E:This alternative proposes: Validate that all nonbackbone OSPF areas have a supported logical connection to area 0, and use virtual links only as a documented transitional design. It concerns a different Junos engineering issue OSPF multi-area backbone connectivity and virtual-link limitations, not the directly tested provider-network issue Anycast RP resilient multicast service and routing policy.
Question 331
A Junos service-provider routing engineer investigates the following routing and service incident: Two separate customers both use 10.10.0.0/16 and an engineer proposes one shared RD with no RT isolation on the PE. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.
- Choose a supported VPLS signaling model and verify peer discovery, service membership and MPLS forwarding transport independently.
- Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone.
- Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies.
- Trace a VPNv4 prefix from MP-BGP reception to a customer VRF routing table, distinguishing provider VPN control-plane storage and installed customer forwarding routes.
Explanation
Correct Answer
C:The case-specific routing and services action is: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies. The governing Junos routing/service principle is: An RD distinguishes overlapping customer prefix routes in MP-BGP VPN NLRI, whereas RT extended communities guide import/export membership across VPN routing instances.
Incorrect Answers
A:This alternative proposes: Choose a supported VPLS signaling model and verify peer discovery, service membership and MPLS forwarding transport independently. It concerns a different Junos engineering issue VPLS service control plane LDP versus BGP distribution, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
B:This alternative proposes: Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone. It concerns a different Junos engineering issue Multicast VPN provider and customer traffic separation, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
D:This alternative proposes: Trace a VPNv4 prefix from MP-BGP reception to a customer VRF routing table, distinguishing provider VPN control-plane storage and installed customer forwarding routes. It concerns a different Junos engineering issue VPNv4 bgp.l3vpn.0 versus customer VRF route tables, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
Question 332
A provider routing design review considers this situation. Two separate customers both use 10.10.0.0/16 and an engineer proposes one shared RD with no RT isolation on the PE. A colleague proposes: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies. Which technical principle BEST supports that action? Select ONE best answer.
- An RD distinguishes overlapping customer prefix routes in MP-BGP VPN NLRI, whereas RT extended communities guide import/export membership across VPN routing instances.
- SoO identifies the originating customer site for policy-based loop prevention; OSPF sham links can influence customer OSPF path choice across the VPN backbone in particular backdoor-link designs.
- MP-BGP carries routes for negotiated address families and associated path attributes; mismatched family configuration can block specific NLRI even when the underlying BGP session remains up.
- PE/CE exchange can use a supported static, BGP, OSPF or other mechanism; the customer interface must belong to the intended VRF and outbound policy determines what enters VPN reachability.
Explanation
Correct Answer
A:The relevant Junos service-provider networking principle is: An RD distinguishes overlapping customer prefix routes in MP-BGP VPN NLRI, whereas RT extended communities guide import/export membership across VPN routing instances. In the described provider-network case (Two separate customers both use 10.10.0.0/16 and an engineer proposes one shared RD with no RT isolation on the PE.), it supports the planned action: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies.
Incorrect Answers
B:This alternative proposes: SoO identifies the originating customer site for policy-based loop prevention; OSPF sham links can influence customer OSPF path choice across the VPN backbone in particular backdoor-link designs. It concerns a different Junos engineering issue Site of Origin and OSPF sham-link loop control, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
C:This alternative proposes: MP-BGP carries routes for negotiated address families and associated path attributes; mismatched family configuration can block specific NLRI even when the underlying BGP session remains up. It concerns a different Junos engineering issue Multiprotocol BGP family negotiations and VPN routes, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
D:This alternative proposes: PE/CE exchange can use a supported static, BGP, OSPF or other mechanism; the customer interface must belong to the intended VRF and outbound policy determines what enters VPN reachability. It concerns a different Junos engineering issue PE to CE routing and customer route redistribution, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
Question 333
A Juniper service-provider engineer needs decisive verification evidence for this situation. Two separate customers both use 10.10.0.0/16 and an engineer proposes one shared RD with no RT isolation on the PE. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.
- Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population.
- Check CE neighbor health, routing-instance interface membership, customer prefixes in instance.inet.0, VRF export policy and remote import results.
- Inspect VPN route label, resolved tunnel in inet.3, label-switched path, control-plane next hop, penultimate-hop behavior and egress VRF lookup.
- Review route-policy terms, L1 and L2 route databases, leaked prefix entries, interface scope and next-hop resolution from affected access devices.
Explanation
Correct Answer
A:In the stated situation (Two separate customers both use 10.10.0.0/16 and an engineer proposes one shared RD with no RT isolation on the PE.), the intended acceptance outcome is: Two customers may use the same internal subnet without conflated control-plane identities and only authorized VPNs import each others' prefixes.
Incorrect Answers
B:This alternative proposes: Check CE neighbor health, routing-instance interface membership, customer prefixes in instance.inet.0, VRF export policy and remote import results. It concerns a different Junos engineering issue PE to CE routing and customer route redistribution, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
C:This alternative proposes: Inspect VPN route label, resolved tunnel in inet.3, label-switched path, control-plane next hop, penultimate-hop behavior and egress VRF lookup. It concerns a different Junos engineering issue MPLS VPN transport label stack and next hop, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
D:This alternative proposes: Review route-policy terms, L1 and L2 route databases, leaked prefix entries, interface scope and next-hop resolution from affected access devices. It concerns a different Junos engineering issue IS-IS Level 2 to Level 1 route leaking and summaries, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
Question 334
A service-provider acceptance team reviews the result of a provider-service change. Two separate customers both use 10.10.0.0/16 and an engineer proposes one shared RD with no RT isolation on the PE. The intended verification is: Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population. Which outcome BEST demonstrates success? Select ONE best answer.
- Clients receive authorized routes without a full iBGP mesh and no reflected route loops or unreachable forwarding next hops develop.
- Two customers may use the same internal subnet without conflated control-plane identities and only authorized VPNs import each others' prefixes.
- The ingress PE pushes an appropriate label stack and the egress PE forwards the packet in the authorized customer context without exposing traffic to another VPN.
- The correct VPN route is visible in the intended customer VRF with a valid forwarding next hop and is absent from unauthorized VRFs.
Explanation
Correct Answer
B:The verified success outcome is: Two customers may use the same internal subnet without conflated control-plane identities and only authorized VPNs import each others' prefixes. Confirm this by: Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population.
Incorrect Answers
A:That option concerns BGP route reflectors originator and cluster loop prevention. The related controlled intervention is: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies.
C:That option concerns MPLS VPN transport label stack and next hop. The related controlled intervention is: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies.
D:This alternative proposes: The correct VPN route is visible in the intended customer VRF with a valid forwarding next hop and is absent from unauthorized VRFs. It concerns a different Junos engineering issue VPNv4 bgp.l3vpn.0 versus customer VRF route tables, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets in the stated situation (Two separate customers both use 10.10.0.0/16 and an engineer proposes one shared RD with no RT isolation on the PE.). A better case-specific check is: Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population. The more targeted action is: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies.
Question 335
A provider change-review board examines this Junos service case. Two separate customers both use 10.10.0.0/16 and an engineer proposes one shared RD with no RT isolation on the PE. Which THREE statements together give an appropriate corrective action, supporting diagnostic check and success outcome? Select THREE answers.
- Two customers may use the same internal subnet without conflated control-plane identities and only authorized VPNs import each others' prefixes.
- Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding.
- Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies.
- Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population.
- Tune congestion drop behavior and outbound packet markings while preserving intentional service differentiation across trusted interfaces.
- Check OSPFv3 adjacency and IPv6 reachability through supported Junos ospf3 operational commands rather than assuming an IPv4 OSPFv2 adjacency proves IPv6 is working.
Explanation
Correct Answers
A:Confirm this by: Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population.
C:The case-specific routing and services action is: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies. The governing Junos routing/service principle is: An RD distinguishes overlapping customer prefix routes in MP-BGP VPN NLRI, whereas RT extended communities guide import/export membership across VPN routing instances. Verify the decision through: Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population.
D:The direct discriminating observation is: Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population. In the stated situation (Two separate customers both use 10.10.0.0/16 and an engineer proposes one shared RD with no RT isolation on the PE.), the intended acceptance outcome is: Two customers may use the same internal subnet without conflated control-plane identities and only authorized VPNs import each others' prefixes.
Incorrect Answers
B:That option concerns Multicast VPN provider and customer traffic separation. Confirm this by: Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population.
E:That option concerns CoS RED drop profiles and rewrite-marking validation. Confirm this by: Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population.
F:That option concerns OSPFv3 IPv6 neighbor and IPv4 separation. Confirm this by: Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population.
Question 336
A Junos service-provider routing engineer investigates the following routing and service incident: A provider changes an RT export value but expects remote PE VRFs to import the same routes despite no matching import targets. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.
- Verify the transport and service label roles in an MPLS Layer 3 VPN before attributing a forwarding failure to the customer routing protocol.
- Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
- Verify the recursive resolution of a BGP NEXT_HOP before changing route selection preferences or assuming a received prefix is usable.
- Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies.
Explanation
Correct Answer
D:The case-specific routing and services action is: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies.
Incorrect Answers
A:This alternative proposes: Verify the transport and service label roles in an MPLS Layer 3 VPN before attributing a forwarding failure to the customer routing protocol. It concerns a different Junos engineering issue MPLS VPN transport label stack and next hop, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
B:This alternative proposes: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection. It concerns a different Junos engineering issue Site of Origin and OSPF sham-link loop control, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
C:This alternative proposes: Verify the recursive resolution of a BGP NEXT_HOP before changing route selection preferences or assuming a received prefix is usable. It concerns a different Junos engineering issue BGP NEXT_HOP reachability and inet.3 recursion, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
Question 337
A provider routing design review considers this situation. A provider changes an RT export value but expects remote PE VRFs to import the same routes despite no matching import targets. A colleague proposes: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies. Which technical principle BEST supports that action? Select ONE best answer.
- An RD distinguishes overlapping customer prefix routes in MP-BGP VPN NLRI, whereas RT extended communities guide import/export membership across VPN routing instances.
- IS-IS uses LSPs to distribute link-state topology and SNP mechanisms to synchronize databases; incomplete flooding can leave routers computing different SPF paths.
- VPN topology is shaped by which prefixes are imported/exported between sites, and a shared service or Internet breakout must be explicitly engineered rather than assumed by one RT value.
- SoO identifies the originating customer site for policy-based loop prevention; OSPF sham links can influence customer OSPF path choice across the VPN backbone in particular backdoor-link designs.
Explanation
Correct Answer
A:The relevant Junos service-provider networking principle is: An RD distinguishes overlapping customer prefix routes in MP-BGP VPN NLRI, whereas RT extended communities guide import/export membership across VPN routing instances. In the described provider-network case (A provider changes an RT export value but expects remote PE VRFs to import the same routes despite no matching import targets.), it supports the planned action: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies.
Incorrect Answers
B:This alternative proposes: IS-IS uses LSPs to distribute link-state topology and SNP mechanisms to synchronize databases; incomplete flooding can leave routers computing different SPF paths. It concerns a different Junos engineering issue IS-IS link-state packet flooding and database consistency, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
C:This alternative proposes: VPN topology is shaped by which prefixes are imported/exported between sites, and a shared service or Internet breakout must be explicitly engineered rather than assumed by one RT value. It concerns a different Junos engineering issue Layer 3 VPN hub spoke topology and controlled Internet breakout, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
D:This alternative proposes: SoO identifies the originating customer site for policy-based loop prevention; OSPF sham links can influence customer OSPF path choice across the VPN backbone in particular backdoor-link designs. It concerns a different Junos engineering issue Site of Origin and OSPF sham-link loop control, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
Question 338
A Juniper service-provider engineer needs decisive verification evidence for this situation. A provider changes an RT export value but expects remote PE VRFs to import the same routes despite no matching import targets. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.
- Check CE neighbor health, routing-instance interface membership, customer prefixes in instance.inet.0, VRF export policy and remote import results.
- Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population.
- Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding.
- Inspect SSM group range, IGMPv3 (S,G) membership, source unicast route, RPF state, PIM joins and actual packet counts.
Explanation
Correct Answer
B:In the stated situation (A provider changes an RT export value but expects remote PE VRFs to import the same routes despite no matching import targets.), the intended acceptance outcome is: Two customers may use the same internal subnet without conflated control-plane identities and only authorized VPNs import each others' prefixes.
Incorrect Answers
A:This alternative proposes: Check CE neighbor health, routing-instance interface membership, customer prefixes in instance.inet.0, VRF export policy and remote import results. It concerns a different Junos engineering issue PE to CE routing and customer route redistribution, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
C:This alternative proposes: Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding. It concerns a different Junos engineering issue Multicast VPN provider and customer traffic separation, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
D:This alternative proposes: Inspect SSM group range, IGMPv3 (S,G) membership, source unicast route, RPF state, PIM joins and actual packet counts. It concerns a different Junos engineering issue Source-specific multicast and IGMPv3 source filtering, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
Question 339
A service-provider acceptance team reviews the result of a provider-service change. A provider changes an RT export value but expects remote PE VRFs to import the same routes despite no matching import targets. The intended verification is: Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population. Which outcome BEST demonstrates success? Select ONE best answer.
- Two customers may use the same internal subnet without conflated control-plane identities and only authorized VPNs import each others' prefixes.
- The session establishes over the intended transport and advertises only authorized routing information even across a link failure.
- Each site advertises and learns only authorized enterprise routes, without leaking internal core routes or other tenants' networks.
- The intended remote VPN site can reach its authorized peer across the AS boundary without transferring unrelated tenants' routes or losing required label resolution.
Explanation
Correct Answer
A:The verified success outcome is: Two customers may use the same internal subnet without conflated control-plane identities and only authorized VPNs import each others' prefixes. Confirm this by: Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population. The related controlled intervention is: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies.
Incorrect Answers
B:That option concerns BGP external multihop and loopback peer reachability. The related controlled intervention is: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies.
C:That option concerns PE to CE routing and customer route redistribution. The related controlled intervention is: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies.
D:That option concerns Interprovider Layer 3 VPN options and carrier of carriers. The related controlled intervention is: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies.
Question 340
A Junos service-provider routing engineer investigates this service-provider network scenario. A provider changes an RT export value but expects remote PE VRFs to import the same routes despite no matching import targets. Which TWO complementary steps combine a suitable technical action and its direct verification? Select TWO answers.
- Inspect broadcast-network DR and BDR election state and interface priority before attempting to control database exchange behavior on an Ethernet shared segment.
- Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies.
- Design an eBGP multihop session with explicit remote loopback reachability and appropriate TTL/session transport settings when directly connected peering is not used.
- Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population.
- Inspect show route table bgp.l3vpn.0, instance.inet.0, accepted RT communities, next-hop resolution and label information at both PEs.
Explanation
Correct Answers
B:The case-specific routing and services action is: Separate route distinguishers for VPN-IPv4 address uniqueness from route targets that control eligible VPN route import and export policies. Verify the decision through: Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population.
D:The direct discriminating observation is: Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population. In the stated situation (A provider changes an RT export value but expects remote PE VRFs to import the same routes despite no matching import targets.), the intended acceptance outcome is: Two customers may use the same internal subnet without conflated control-plane identities and only authorized VPNs import each others' prefixes.
Incorrect Answers
A:This alternative proposes: Inspect broadcast-network DR and BDR election state and interface priority before attempting to control database exchange behavior on an Ethernet shared segment. It concerns a different Junos engineering issue OSPF designated router election on a multiaccess segment, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
C:This alternative proposes: Design an eBGP multihop session with explicit remote loopback reachability and appropriate TTL/session transport settings when directly connected peering is not used. It concerns a different Junos engineering issue BGP external multihop and loopback peer reachability, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.
E:This alternative proposes: Inspect show route table bgp.l3vpn.0, instance.inet.0, accepted RT communities, next-hop resolution and label information at both PEs. It concerns a different Junos engineering issue VPNv4 bgp.l3vpn.0 versus customer VRF route tables, not the directly tested provider-network issue Layer 3 VPN route distinguishers versus route targets.