cert
cert-1
cert-2

Pass Fortinet NSE5_FSW_AD-7.6 Exam in First Attempt Guaranteed!

Get 100% Latest Exam Questions, Accurate & Verified Answers to Pass the Actual Exam!
30 Days Free Updates, Instant Download!

cert-5
cert-6
NSE5_FSW_AD-7.6 Exam - Verified By Experts
NSE5_FSW_AD-7.6 Premium File

NSE5_FSW_AD-7.6 Premium File

$69.99
$76.99
  • Premium File 64 Questions & Answers. Last Update: Nov 15, 2026

Whats Included:

  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
 
$76.99
$69.99
accept 42 downloads in the last 7 days
block-screenshots
Fortinet NSE5_FSW_AD-7.6 Practice Test 40

Question 390

An approved static-IP server is blocked because its switch port lacks a binding entry after enabling source guard. Which observable result BEST proves the intended FortiSwitch operation or security policy works?

  1. Unauthorized source IP packets fail while an approved host continues using its assigned IP and address policy.
  2. Exactly the intended serial joins managed inventory and receives approved controller settings after authorization.
  3. Authorized endpoints enter only permitted VLANs while failed authentication is denied or restricted according to policy.
  4. Legitimate clients lease addresses while rogue DHCP servers connected to untrusted access ports cannot answer.

Explanation

Correct Answer

A:

Unauthorized source IP packets fail while an approved host continues using its assigned IP and address policy. Source guard is an ingress source-binding check, not a full replacement for routed firewall policies or endpoint security.

Incorrect Answers

B:

Exactly the intended serial joins managed inventory and receives approved controller settings after authorization. This result relates to Discovered versus authorized FortiSwitch state, not the acceptance condition under test. The relevant result is: Unauthorized source IP packets fail while an approved host continues using its assigned IP and address policy.

C:

Authorized endpoints enter only permitted VLANs while failed authentication is denied or restricted according to policy. This result relates to FortiSwitch 802.1X port-based authentication, not the acceptance condition under test. The relevant result is: Unauthorized source IP packets fail while an approved host continues using its assigned IP and address policy.

D:

Legitimate clients lease addresses while rogue DHCP servers connected to untrusted access ports cannot answer. This result relates to DHCP snooping trust-boundary enforcement, not the acceptance condition under test. The relevant result is: Unauthorized source IP packets fail while an approved host continues using its assigned IP and address policy.

Question 391

A PoE access switch can power legacy phones but sheds newer high-power access points after lunch. Which TWO complementary steps identify the appropriate FortiSwitch response AND the evidence needed to verify it? Select TWO.

  1. Compare controller desired VLAN map, current switch running state, configuration synchronization and post-reboot behavior.
  2. Check switch PoE budget, port class, negotiated allocation, PSU state, LLDP-MED power TLV and port events.
  3. Management control and authorized user traffic work over the direct connection without confusing them.
  4. Validate the supported PoE budget and LLDP-MED endpoint power negotiation rather than equating link up with adequate wattage.
  5. Configure supported LLDP-MED voice policy so a compatible handset learns its VLAN and traffic priority.

Explanation

Correct Answers

B:

Check switch PoE budget, port class, negotiated allocation, PSU state, LLDP-MED power TLV and port events. Port count and Ethernet link state do not guarantee sufficient power for high-draw endpoints. The paired action is: Validate the supported PoE budget and LLDP-MED endpoint power negotiation rather than equating link up with adequate wattage. This is the diagnostic or verification half of the requested TWO-step pair.

D:

Validate the supported PoE budget and LLDP-MED endpoint power negotiation rather than equating link up with adequate wattage. Port count and Ethernet link state do not guarantee sufficient power for high-draw endpoints. Verify the action with: Check switch PoE budget, port class, negotiated allocation, PSU state, LLDP-MED power TLV and port events. This is the configuration or remediation half of the requested TWO-step pair.

Incorrect Answers

A:

Compare controller desired VLAN map, current switch running state, configuration synchronization and post-reboot behavior. This step concerns VLAN configuration persistence and drift control and is not part of the required paired solution. The correct action and evidence are: Validate the supported PoE budget and LLDP-MED endpoint power negotiation rather than equating link up with adequate wattage. Together with: Check switch PoE budget, port class, negotiated allocation, PSU state, LLDP-MED power TLV and port events.

C:

Management control and authorized user traffic work over the direct connection without confusing them. This step concerns Single FortiGate and single FortiSwitch topology and is not part of the required paired solution. The correct action and evidence are: Validate the supported PoE budget and LLDP-MED endpoint power negotiation rather than equating link up with adequate wattage. Together with: Check switch PoE budget, port class, negotiated allocation, PSU state, LLDP-MED power TLV and port events.

E:

Configure supported LLDP-MED voice policy so a compatible handset learns its VLAN and traffic priority. This step concerns LLDP-MED voice network policy advertisements and is not part of the required paired solution. The correct action and evidence are: Validate the supported PoE budget and LLDP-MED endpoint power negotiation rather than equating link up with adequate wattage. Together with: Check switch PoE budget, port class, negotiated allocation, PSU state, LLDP-MED power TLV and port events.

Question 392

A contractor requests a full week of unfiltered packet data from a production finance VLAN to diagnose one DHCP issue. Which observable result BEST proves the intended FortiSwitch operation or security policy works?

  1. The failing physical or logical port is identified through reproducible counters rather than visual LED assumptions.
  2. The new FortiSwitch discovers the designated controller while unrelated FortiGate interfaces retain their normal function.
  3. Troubleshooting evidence is sufficient to establish the fault without exporting unnecessary private communications.
  4. The intended switch appears in discovery after restoring the precise missing interface or transport prerequisite.

Explanation

Correct Answer

C:

Troubleshooting evidence is sufficient to establish the fault without exporting unnecessary private communications. A packet-capture tool may record payloads and credentials, so evidence handling is part of the network security process.

Incorrect Answers

A:

The failing physical or logical port is identified through reproducible counters rather than visual LED assumptions. This result relates to Managed switch port statistics and counter analysis, not the acceptance condition under test. The relevant result is: Troubleshooting evidence is sufficient to establish the fault without exporting unnecessary private communications.

B:

The new FortiSwitch discovers the designated controller while unrelated FortiGate interfaces retain their normal function. This result relates to FortiLink management interface provisioning, not the acceptance condition under test. The relevant result is: Troubleshooting evidence is sufficient to establish the fault without exporting unnecessary private communications.

D:

The intended switch appears in discovery after restoring the precise missing interface or transport prerequisite. This result relates to FortiLink discovery failure and physical uplink path, not the acceptance condition under test. The relevant result is: Troubleshooting evidence is sufficient to establish the fault without exporting unnecessary private communications.

Question 393

A relay receives mismatched Option 82 information and discards legitimate client renewals. Which diagnostic evidence should the FortiSwitch administrator examine FIRST?

  1. Inspect frame-rate counters by class, threshold configuration, affected VLANs and protocol health under controlled load.
  2. Inspect ARP inspection status, DHCP snooping binding database, source MAC/IP, trusted ports and violation logs.
  3. Check per-member speed, partner identity, state, optical counters, VLAN tags and aggregate distribution.
  4. Inspect DHCP server permitted list, Option 82 insertion/trust state, relay path, client bindings and lease evidence.

Explanation

Correct Answer

D:

Inspect DHCP server permitted list, Option 82 insertion/trust state, relay path, client bindings and lease evidence. DHCP server allowlist and Option 82 metadata provide additional context but cannot correct a failed VLAN or missing upstream relay. The paired action is: Use documented trusted DHCP-server lists or Option 82 information where supported to enforce authorized address assignment.

Incorrect Answers

A:

Inspect frame-rate counters by class, threshold configuration, affected VLANs and protocol health under controlled load. These observations are applicable to Storm-control thresholds and broadcast containment, but would not isolate the main failure first. The decisive evidence is: Inspect DHCP server permitted list, Option 82 insertion/trust state, relay path, client bindings and lease evidence.

B:

Inspect ARP inspection status, DHCP snooping binding database, source MAC/IP, trusted ports and violation logs. These observations are applicable to Dynamic ARP inspection with DHCP snooping bindings, but would not isolate the main failure first. The decisive evidence is: Inspect DHCP server permitted list, Option 82 insertion/trust state, relay path, client bindings and lease evidence.

C:

Check per-member speed, partner identity, state, optical counters, VLAN tags and aggregate distribution. These observations are applicable to Link aggregation and port error recovery, but would not isolate the main failure first. The decisive evidence is: Inspect DHCP server permitted list, Option 82 insertion/trust state, relay path, client bindings and lease evidence.

Question 394

Two distribution switches have different MST region revisions and flood after a redundant connection is added. Which FortiSwitch configuration or corrective action BEST addresses the requirement?

  1. Check MAC-learning table and flooding behavior before replacing a switch or changing its IP routing.
  2. Use STP state and MAC move evidence to isolate one bad bridging path and change only the proven element.
  3. Select a consistent supported MSTP region and intentional root-bridge placement for loop-free L2 redundancy.
  4. Set model-supported dynamic MAC address learning limits and specific violation action on access-facing switch ports.

Explanation

Correct Answer

C:

Select a consistent supported MSTP region and intentional root-bridge placement for loop-free L2 redundancy. Different MST configuration identifiers split regions even if switch ports are physically connected. Verify the action with: Review MST region name, revision, VLAN instance map, bridge priorities, root ID and topology-change counters.

Incorrect Answers

A:

Check MAC-learning table and flooding behavior before replacing a switch or changing its IP routing. This action is relevant to Layer 2 MAC-learning and forwarding decisions, not the controlling requirement in this case. An L2 switch uses MAC destination and VLAN state for forwarding; a healthy SVI is not proof a host is on the proper port. The targeted response is: Select a consistent supported MSTP region and intentional root-bridge placement for loop-free L2 redundancy.

B:

Use STP state and MAC move evidence to isolate one bad bridging path and change only the proven element. This action is relevant to STP incident recovery with MAC flap evidence, not the controlling requirement in this case. Packet loss during a bridging loop can coexist with clean optical counters, so L1-only diagnostics miss the root cause. The targeted response is: Select a consistent supported MSTP region and intentional root-bridge placement for loop-free L2 redundancy.

D:

Set model-supported dynamic MAC address learning limits and specific violation action on access-facing switch ports. This action is relevant to Port MAC learning-limit and violation controls, not the controlling requirement in this case. Dynamic MAC learning limits reduce accidental fan-out but should be tuned for legitimate multi-device access designs. The targeted response is: Select a consistent supported MSTP region and intentional root-bridge placement for loop-free L2 redundancy.

Question 395

An engineer accidentally configures the laptop's analyzer port as a production access uplink rather than the monitor destination. Which FortiSwitch configuration or corrective action BEST addresses the requirement?

  1. Troubleshoot FortiLink discovery from physical and logical interface configuration through LLDP and management addressing.
  2. Investigate managed switch offline or configuration mismatch after firmware upgrade or controller resynchronization using both endpoints.
  3. Validate the supported PoE budget and LLDP-MED endpoint power negotiation rather than equating link up with adequate wattage.
  4. Mirror only the relevant source ports or VLAN traffic to a dedicated analyzer destination using supported SPAN settings.

Explanation

Correct Answer

D:

Mirror only the relevant source ports or VLAN traffic to a dedicated analyzer destination using supported SPAN settings. A mirrored stream is passive evidence and can be incomplete if analyzer bandwidth is lower than the observed traffic. Verify the action with: Inspect mirror direction, source and destination ports, speed constraints, physical capture link and switch statistics.

Incorrect Answers

A:

Troubleshoot FortiLink discovery from physical and logical interface configuration through LLDP and management addressing. This action is relevant to FortiLink discovery failure and physical uplink path, not the controlling requirement in this case. A green Ethernet link is necessary for many paths but does not prove the FortiLink management protocol or discovery is working. The targeted response is: Mirror only the relevant source ports or VLAN traffic to a dedicated analyzer destination using supported SPAN settings.

B:

Investigate managed switch offline or configuration mismatch after firmware upgrade or controller resynchronization using both endpoints. This action is relevant to FortiLink synchronization and upgrade troubleshooting, not the controlling requirement in this case. Managed switches can be reachable at Layer 2 yet show stale policy after incompatible upgrade or failed controller push. The targeted response is: Mirror only the relevant source ports or VLAN traffic to a dedicated analyzer destination using supported SPAN settings.

C:

Validate the supported PoE budget and LLDP-MED endpoint power negotiation rather than equating link up with adequate wattage. This action is relevant to PoE and LLDP-MED endpoint power coordination, not the controlling requirement in this case. Port count and Ethernet link state do not guarantee sufficient power for high-draw endpoints. The targeted response is: Mirror only the relevant source ports or VLAN traffic to a dedicated analyzer destination using supported SPAN settings.

Question 396

A previously used standalone switch never auto-discovers because its old configuration prevents expected default provisioning. Which diagnostic evidence should the FortiSwitch administrator examine FIRST?

  1. Inspect port profile assignment, FortiGate controller policy, client role, enforcement counters and overlapping static controls.
  2. Inspect factory-default mode, DHCP or discovery exchange, upstream native VLAN, FortiLink enablement, NTP and controller authorization.
  3. Inspect FortiLink mode, physical or aggregate link state, switch authorization, VLAN interfaces and test-client path.
  4. Check ingress port, assigned VLAN ID, owner VDOM, gateway, firewall session path and cross-tenant deny counters.

Explanation

Correct Answer

B:

Inspect factory-default mode, DHCP or discovery exchange, upstream native VLAN, FortiLink enablement, NTP and controller authorization. Zero-touch deployment works only when the necessary discovery path and identity checks function; a link LED is insufficient. The paired action is: Prepare supported provisioning, DHCP, management connectivity and secure bootstrap before assuming a factory-default FortiSwitch will auto-configure.

Incorrect Answers

A:

Inspect port profile assignment, FortiGate controller policy, client role, enforcement counters and overlapping static controls. These observations are applicable to FortiSwitch security profile application and precedence, but would not isolate the main failure first. The decisive evidence is: Inspect factory-default mode, DHCP or discovery exchange, upstream native VLAN, FortiLink enablement, NTP and controller authorization.

C:

Inspect FortiLink mode, physical or aggregate link state, switch authorization, VLAN interfaces and test-client path. These observations are applicable to Single FortiGate and single FortiSwitch topology, but would not isolate the main failure first. The decisive evidence is: Inspect factory-default mode, DHCP or discovery exchange, upstream native VLAN, FortiLink enablement, NTP and controller authorization.

D:

Check ingress port, assigned VLAN ID, owner VDOM, gateway, firewall session path and cross-tenant deny counters. These observations are applicable to Managed tenant troubleshooting across controller and access layer, but would not isolate the main failure first. The decisive evidence is: Inspect factory-default mode, DHCP or discovery exchange, upstream native VLAN, FortiLink enablement, NTP and controller authorization.

Question 397

An organization disconnects FortiLink to deploy standalone management but fails to assign a reachable management IP and default route. Which TWO complementary steps identify the appropriate FortiSwitch response AND the evidence needed to verify it? Select TWO.

  1. Inspect FortiLink operational mode, controller ownership, current management address, VDOM and switch model support.
  2. Check MAC-learning table and flooding behavior before replacing a switch or changing its IP routing.
  3. Unauthorized source IP packets fail while an approved host continues using its assigned IP and address policy.
  4. Determine whether a switch is managed by FortiGate or standalone before setting interfaces, routes or admin policies.
  5. Check per-member speed, partner identity, state, optical counters, VLAN tags and aggregate distribution.

Explanation

Correct Answers

A:

Inspect FortiLink operational mode, controller ownership, current management address, VDOM and switch model support. Direct edits on a managed switch can be overridden; standalone configuration must be maintained and backed up independently. The paired action is: Determine whether a switch is managed by FortiGate or standalone before setting interfaces, routes or admin policies. This is the diagnostic or verification half of the requested TWO-step pair.

D:

Determine whether a switch is managed by FortiGate or standalone before setting interfaces, routes or admin policies. Direct edits on a managed switch can be overridden; standalone configuration must be maintained and backed up independently. Verify the action with: Inspect FortiLink operational mode, controller ownership, current management address, VDOM and switch model support. This is the configuration or remediation half of the requested TWO-step pair.

Incorrect Answers

B:

Check MAC-learning table and flooding behavior before replacing a switch or changing its IP routing. This step concerns Layer 2 MAC-learning and forwarding decisions and is not part of the required paired solution. The correct action and evidence are: Determine whether a switch is managed by FortiGate or standalone before setting interfaces, routes or admin policies. Together with: Inspect FortiLink operational mode, controller ownership, current management address, VDOM and switch model support.

C:

Unauthorized source IP packets fail while an approved host continues using its assigned IP and address policy. This step concerns IPv4 source guard and binding-based packet filtering and is not part of the required paired solution. The correct action and evidence are: Determine whether a switch is managed by FortiGate or standalone before setting interfaces, routes or admin policies. Together with: Inspect FortiLink operational mode, controller ownership, current management address, VDOM and switch model support.

E:

Check per-member speed, partner identity, state, optical counters, VLAN tags and aggregate distribution. This step concerns Link aggregation and port error recovery and is not part of the required paired solution. The correct action and evidence are: Determine whether a switch is managed by FortiGate or standalone before setting interfaces, routes or admin policies. Together with: Inspect FortiLink operational mode, controller ownership, current management address, VDOM and switch model support.

Question 398

A network engineer selects a breakout option not supported by its FortiSwitch hardware revision. Which observable result BEST proves the intended FortiSwitch operation or security policy works?

  1. All expected child interfaces enumerate at supported speeds without disrupting unrelated uplinks.
  2. An access host receives the right subnet while only approved tagged VLANs traverse the uplink.
  3. A controlled FortiGate HA failover leaves managed switches authorized and required client access functioning.
  4. Rapid MAC moves stop and normal forwarding returns with a verified alternate redundant path.

Explanation

Correct Answer

A:

All expected child interfaces enumerate at supported speeds without disrupting unrelated uplinks. A physical QSFP cage does not guarantee that four independent Ethernet child ports can be enabled on every model.

Incorrect Answers

B:

An access host receives the right subnet while only approved tagged VLANs traverse the uplink. This result relates to FortiSwitch native VLAN versus allowed VLANs, not the acceptance condition under test. The relevant result is: All expected child interfaces enumerate at supported speeds without disrupting unrelated uplinks.

C:

A controlled FortiGate HA failover leaves managed switches authorized and required client access functioning. This result relates to HA FortiGate pair managing switch topology, not the acceptance condition under test. The relevant result is: All expected child interfaces enumerate at supported speeds without disrupting unrelated uplinks.

D:

Rapid MAC moves stop and normal forwarding returns with a verified alternate redundant path. This result relates to STP incident recovery with MAC flap evidence, not the acceptance condition under test. The relevant result is: All expected child interfaces enumerate at supported speeds without disrupting unrelated uplinks.

Question 399

An engineer moves a port into a different security group without verifying the FortiGate controller template. Which FortiSwitch configuration or corrective action BEST addresses the requirement?

  1. Apply changes on the FortiGate controller and verify installed FortiSwitch state and reconciliation before rebooting.
  2. Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context.
  3. Authorize only intended discovered FortiSwitch serial numbers and confirm management mode after the expected transition.
  4. Create an appropriate FortiGate FortiLink physical or logical interface with supported addressing and controller capabilities before onboarding a switch.

Explanation

Correct Answer

A:

Apply changes on the FortiGate controller and verify installed FortiSwitch state and reconciliation before rebooting. Local changes on a FortiLink-managed switch can be discarded when the FortiGate controller reapplies its known configuration. Verify the action with: Compare desired switch controller settings, switch synchronization indicators, port VLANs, user roles and post-reboot configuration.

Incorrect Answers

B:

Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context. This action is relevant to FortiSwitch SVI routing and connected routes, not the controlling requirement in this case. Layer-3 SVI configuration and actual usable forwarding are separate from having a named Layer-2 VLAN. The targeted response is: Apply changes on the FortiGate controller and verify installed FortiSwitch state and reconciliation before rebooting.

C:

Authorize only intended discovered FortiSwitch serial numbers and confirm management mode after the expected transition. This action is relevant to Discovered versus authorized FortiSwitch state, not the controlling requirement in this case. Switch discovery is not the same as authorization; auto-authorization has governance implications and a managed-mode transition may reboot the device. The targeted response is: Apply changes on the FortiGate controller and verify installed FortiSwitch state and reconciliation before rebooting.

D:

Create an appropriate FortiGate FortiLink physical or logical interface with supported addressing and controller capabilities before onboarding a switch. This action is relevant to FortiLink management interface provisioning, not the controlling requirement in this case. A FortiGate port not configured for FortiLink cannot assume managed-switch ownership from physical connection alone. The targeted response is: Apply changes on the FortiGate controller and verify installed FortiSwitch state and reconciliation before rebooting.

Question 400

Two distribution switches report an unexpected LLDP neighbor after a contractor reroutes patch cables. Which observable result BEST proves the intended FortiSwitch operation or security policy works?

  1. The current neighboring device and optional endpoint location are visible and match approved cabling documentation.
  2. Phones and access points receive stable allocated power while redundant PSU and priority policies remain within budget.
  3. Known printers and IoT devices enter their restricted VLANs while unknown endpoints have no excessive access.
  4. Latency-sensitive flows improve under representative load while other business services remain functional.

Explanation

Correct Answer

A:

The current neighboring device and optional endpoint location are visible and match approved cabling documentation. LLDP is an L2 discovery protocol and cannot prove the whole routed service path or phone emergency-location correctness by itself.

Incorrect Answers

B:

Phones and access points receive stable allocated power while redundant PSU and priority policies remain within budget. This result relates to PoE and LLDP-MED endpoint power coordination, not the acceptance condition under test. The relevant result is: The current neighboring device and optional endpoint location are visible and match approved cabling documentation.

C:

Known printers and IoT devices enter their restricted VLANs while unknown endpoints have no excessive access. This result relates to NAC dynamic port policy device classification, not the acceptance condition under test. The relevant result is: The current neighboring device and optional endpoint location are visible and match approved cabling documentation.

D:

Latency-sensitive flows improve under representative load while other business services remain functional. This result relates to Egress priority scheduling and congestion visibility, not the acceptance condition under test. The relevant result is: The current neighboring device and optional endpoint location are visible and match approved cabling documentation.

Fortinet NSE 5 - FortiSwitch 7.6 Administrator (NSE5_FSW_AD-7.6) Practice Tests