CompTIA N10-009 Practice Test 79
Question 780
The original case was: A network technician needs to locate which patch-panel port carries an unlabeled copper pair. The requirement then changes: The cable is located but users report crossed wire pairs. Which revised action BEST meets this new condition?
- Use nslookup and infer the physical port from DNS results.
- Use a cable tester or certifier to validate pinout and pair mapping.
- Use a toner and probe or supported cable tracing equipment.
- The traced pair matches the expected wall outlet and switch port.
Explanation
Correct Answer
B:A toner establishes location while a tester checks electrical correctness. The revised requirement is: The cable is located but users report crossed wire pairs. The appropriate action is: Use a cable tester or certifier to validate pinout and pair mapping.
Incorrect Answers
A:Name resolution cannot identify unlabeled physical cable terminations. It remains inappropriate in the revised context.
C:This is the original control. Cable toners help locate conductors through patch panels and walls. It does not directly satisfy the revised requirement: The cable is located but users report crossed wire pairs.
D:The traced pair matches the expected wall outlet and switch port. The current requirement is: The cable is located but users report crossed wire pairs.
Question 781
A new fiber patch lead may be broken inside a wall but the optical route is undocumented. Which action MOST directly meets the stated networking requirement?
- Use a copper RJ45 continuity tester on the optical fiber core.
- Use a visual fault locator or suitable optical test equipment with proper safety precautions.
- Use calibrated optical power or OTDR testing as appropriate.
- Use show mac-address-table and show vlan with spanning-tree status checks.
Explanation
Correct Answer
B:Visible fault location can reveal accessible fiber breaks or severe bends. This specifically resolves: A new fiber patch lead may be broken inside a wall but the optical route is undocumented.
Incorrect Answers
A:Copper test pins cannot validate light propagation through fiber. The suggested approach is: Use a copper RJ45 continuity tester on the optical fiber core.
C:This action responds to a later condition: A long-haul fiber shows subtle distributed attenuation beyond a simple visible fault. Quantitative optical testing characterizes loss across extended spans.
D:This addresses another problem in objective 5.5: A switch reports unexpected MAC flapping between uplink ports and the engineer must identify the source VLAN.
Question 782
A new fiber patch lead may be broken inside a wall but the optical route is undocumented. A colleague instead suggests: Use a copper RJ45 continuity tester on the optical fiber core. Which finding MOST specifically explains why that suggestion is unsuitable?
- Quantitative optical testing characterizes loss across extended spans.
- DNS AAAA records concern IPv6 name resolution, not switch forwarding state.
- Visible fault location can reveal accessible fiber breaks or severe bends.
- Copper test pins cannot validate light propagation through fiber.
Explanation
Correct Answer
D:Copper test pins cannot validate light propagation through fiber. This flaw directly concerns the proposed action: Use a copper RJ45 continuity tester on the optical fiber core.
Incorrect Answers
A:This rationale belongs to a later changed condition: A long-haul fiber shows subtle distributed attenuation beyond a simple visible fault.
B:This flaw concerns a different case in objective 5.5: A switch reports unexpected MAC flapping between uplink ports and the engineer must identify the source VLAN. The current rejected proposal is: Use a copper RJ45 continuity tester on the optical fiber core.
C:This explains why the recommended control works: Use a visual fault locator or suitable optical test equipment with proper safety precautions.
Question 783
A new fiber patch lead may be broken inside a wall but the optical route is undocumented. After applying the solution 'Use a visual fault locator or suitable optical test equipment with proper safety precautions.', which observation MOST directly proves that the requirement was met?
- The affected VLAN and competing ports are identified and the loop corrected.
- Approval is recorded for 'Use a visual fault locator or suitable optical test equipment with proper safety precautions.' but no operational validation is performed.
- Power values and actual camera startup remain within the rated budget.
- A damaged section is located and the repaired fiber passes optical loss testing.
Explanation
Correct Answer
D:A damaged section is located and the repaired fiber passes optical loss testing. It tests the intended outcome because visible fault location can reveal accessible fiber breaks or severe bends.
Incorrect Answers
A:This observation is for a different condition: A switch reports unexpected MAC flapping between uplink ports and the engineer must identify the source VLAN. It does not directly test the target outcome: A new fiber patch lead may be broken inside a wall but the optical route is undocumented.
B:The missing direct test is: A damaged section is located and the repaired fiber passes optical loss testing.
C:This test addresses a separate problem: A technician needs to verify whether an edge switch has enough PoE capacity for newly installed cameras.
Question 784
The original case was: A new fiber patch lead may be broken inside a wall but the optical route is undocumented. The requirement then changes: A long-haul fiber shows subtle distributed attenuation beyond a simple visible fault. Which revised action BEST meets this new condition?
- Use calibrated optical power or OTDR testing as appropriate.
- Use a copper RJ45 continuity tester on the optical fiber core.
- Use a visual fault locator or suitable optical test equipment with proper safety precautions.
- A damaged section is located and the repaired fiber passes optical loss testing.
Explanation
Correct Answer
A:Quantitative optical testing characterizes loss across extended spans. The revised requirement is: A long-haul fiber shows subtle distributed attenuation beyond a simple visible fault. The appropriate action is: Use calibrated optical power or OTDR testing as appropriate.
Incorrect Answers
B:Copper test pins cannot validate light propagation through fiber. It remains inappropriate in the revised context.
C:This is the original control. Visible fault location can reveal accessible fiber breaks or severe bends. It does not directly satisfy the revised requirement: A long-haul fiber shows subtle distributed attenuation beyond a simple visible fault.
D:A damaged section is located and the repaired fiber passes optical loss testing. The current requirement is: A long-haul fiber shows subtle distributed attenuation beyond a simple visible fault.
Question 785
An engineer suspects an unknown switch is connected behind a port and wants to identify its neighbor. Which action MOST directly meets the stated networking requirement?
- Trace cables and inspect switch MAC learning instead.
- Use only a public website speed test to identify the physically adjacent switch.
- Inspect LLDP or CDP neighbor data with proper trust and device inventory checks.
- Use show power or platform PoE diagnostics and compare draw to budget.
Explanation
Correct Answer
C:Discovery protocols advertise adjacent infrastructure identity and interface details. This specifically resolves: An engineer suspects an unknown switch is connected behind a port and wants to identify its neighbor.
Incorrect Answers
A:This action responds to a later condition: The adjacent endpoint is a legacy appliance that sends no discovery frames. Physical and switching evidence can locate neighbors without discovery advertising.
B:Internet throughput testing does not establish connected neighbor identity. The suggested approach is: Use only a public website speed test to identify the physically adjacent switch.
D:This addresses another problem in objective 5.5: A technician needs to verify whether an edge switch has enough PoE capacity for newly installed cameras.
Question 786
An engineer suspects an unknown switch is connected behind a port and wants to identify its neighbor. A colleague instead suggests: Use only a public website speed test to identify the physically adjacent switch. Which finding MOST specifically explains why that suggestion is unsuitable?
- Internet throughput testing does not establish connected neighbor identity.
- Physical and switching evidence can locate neighbors without discovery advertising.
- Path probes do not measure PoE capacity.
- Discovery protocols advertise adjacent infrastructure identity and interface details.
Explanation
Correct Answer
A:Internet throughput testing does not establish connected neighbor identity. This flaw directly concerns the proposed action: Use only a public website speed test to identify the physically adjacent switch.
Incorrect Answers
B:This rationale belongs to a later changed condition: The adjacent endpoint is a legacy appliance that sends no discovery frames.
C:This flaw concerns a different case in objective 5.5: A technician needs to verify whether an edge switch has enough PoE capacity for newly installed cameras. The current rejected proposal is: Use only a public website speed test to identify the physically adjacent switch.
D:This explains why the recommended control works: Inspect LLDP or CDP neighbor data with proper trust and device inventory checks.
Question 787
An engineer suspects an unknown switch is connected behind a port and wants to identify its neighbor. After applying the solution 'Inspect LLDP or CDP neighbor data with proper trust and device inventory checks.', which observation MOST directly proves that the requirement was met?
- Approval is recorded for 'Inspect LLDP or CDP neighbor data with proper trust and device inventory checks.' but no operational validation is performed.
- Power values and actual camera startup remain within the rated budget.
- Survey results associate weak service with measured coverage or channel contention.
- Neighbor ID and local port agree with the verified topology diagram.
Explanation
Correct Answer
D:Neighbor ID and local port agree with the verified topology diagram. It tests the intended outcome because discovery protocols advertise adjacent infrastructure identity and interface details.
Incorrect Answers
A:Approval alone does not demonstrate operating effectiveness. The missing direct test is: Neighbor ID and local port agree with the verified topology diagram.
B:This observation is for a different condition: A technician needs to verify whether an edge switch has enough PoE capacity for newly installed cameras. It does not directly test the target outcome: An engineer suspects an unknown switch is connected behind a port and wants to identify its neighbor.
C:This test addresses a separate problem: A wireless investigator needs a map of neighboring SSIDs, channels and approximate RSSI around a meeting room.
Question 788
The original case was: An engineer suspects an unknown switch is connected behind a port and wants to identify its neighbor. The requirement then changes: The adjacent endpoint is a legacy appliance that sends no discovery frames. Which revised action BEST meets this new condition?
- Use only a public website speed test to identify the physically adjacent switch.
- Trace cables and inspect switch MAC learning instead.
- Neighbor ID and local port agree with the verified topology diagram.
- Inspect LLDP or CDP neighbor data with proper trust and device inventory checks.
Explanation
Correct Answer
B:Physical and switching evidence can locate neighbors without discovery advertising. The revised requirement is: The adjacent endpoint is a legacy appliance that sends no discovery frames. The appropriate action is: Trace cables and inspect switch MAC learning instead.
Incorrect Answers
A:Internet throughput testing does not establish connected neighbor identity. It remains inappropriate in the revised context.
C:Neighbor ID and local port agree with the verified topology diagram. The current requirement is: The adjacent endpoint is a legacy appliance that sends no discovery frames.
D:This is the original control. Discovery protocols advertise adjacent infrastructure identity and interface details. It does not directly satisfy the revised requirement: The adjacent endpoint is a legacy appliance that sends no discovery frames.
Question 789
A switch reports unexpected MAC flapping between uplink ports and the engineer must identify the source VLAN. Which action MOST directly meets the stated networking requirement?
- Inspect show route and next-hop reachability on routers.
- Use show mac-address-table and show vlan with spanning-tree status checks.
- Use a Wi-Fi analyzer or approved RF survey software to inspect channel and signal distribution.
- Rely only on a DNS AAAA lookup for MAC learning instability.
Explanation
Correct Answer
B:MAC table and VLAN commands identify where layer-2 addresses are learned. This specifically resolves: A switch reports unexpected MAC flapping between uplink ports and the engineer must identify the source VLAN.
Incorrect Answers
A:This action responds to a later condition: The fault moves to a routed network with incorrect gateway choice. Layer 3 route selection needs routing tools rather than MAC-only tables.
C:This addresses another problem in objective 5.5: A wireless investigator needs a map of neighboring SSIDs, channels and approximate RSSI around a meeting room.
D:DNS AAAA records concern IPv6 name resolution, not switch forwarding state. The suggested approach is: Rely only on a DNS AAAA lookup for MAC learning instability.
Question 790
A switch reports unexpected MAC flapping between uplink ports and the engineer must identify the source VLAN. A colleague instead suggests: Rely only on a DNS AAAA lookup for MAC learning instability. Which finding MOST specifically explains why that suggestion is unsuitable?
- Layer 3 route selection needs routing tools rather than MAC-only tables.
- DNS AAAA records concern IPv6 name resolution, not switch forwarding state.
- MAC table and VLAN commands identify where layer-2 addresses are learned.
- Cable toners do not measure radio channels and signal strengths.
Explanation
Correct Answer
B:DNS AAAA records concern IPv6 name resolution, not switch forwarding state. This flaw directly concerns the proposed action: Rely only on a DNS AAAA lookup for MAC learning instability.
Incorrect Answers
A:This rationale belongs to a later changed condition: The fault moves to a routed network with incorrect gateway choice.
C:This explains why the recommended control works: Use show mac-address-table and show vlan with spanning-tree status checks.
D:This flaw concerns a different case in objective 5.5: A wireless investigator needs a map of neighboring SSIDs, channels and approximate RSSI around a meeting room. The current rejected proposal is: Rely only on a DNS AAAA lookup for MAC learning instability.