CompTIA N10-009 Practice Test 78
Question 770
A security engineer needs a packet-level record of a TCP reset sequence during a client-to-server failure. A colleague instead suggests: Use a Wi-Fi antenna meter to decode a routed TCP reset on a wired LAN. Which finding MOST specifically explains why that suggestion is unsuitable?
- Packet captures expose flags, timing and retransmissions not visible in simple ping.
- Name resolution cannot identify unlabeled physical cable terminations.
- Flow metrics efficiently summarize usage without full payload storage.
- RF tools are not substitutes for packet protocol decoding.
Explanation
Correct Answer
D:RF tools are not substitutes for packet protocol decoding. This flaw directly concerns the proposed action: Use a Wi-Fi antenna meter to decode a routed TCP reset on a wired LAN.
Incorrect Answers
A:This explains why the recommended control works: Capture traffic with tcpdump or a protocol analyzer at an authorized observation point.
B:This flaw concerns a different case in objective 5.5: A network technician needs to locate which patch-panel port carries an unlabeled copper pair. The current rejected proposal is: Use a Wi-Fi antenna meter to decode a routed TCP reset on a wired LAN.
C:This rationale belongs to a later changed condition: The task changes to collecting high-level traffic volume over a month.
Question 771
A security engineer needs a packet-level record of a TCP reset sequence during a client-to-server failure. After applying the solution 'Capture traffic with tcpdump or a protocol analyzer at an authorized observation point.', which observation MOST directly proves that the requirement was met?
- A damaged section is located and the repaired fiber passes optical loss testing.
- Approval is recorded for 'Capture traffic with tcpdump or a protocol analyzer at an authorized observation point.' but no operational validation is performed.
- The traced pair matches the expected wall outlet and switch port.
- The capture shows reset direction, port and sequence in the affected flow.
Explanation
Correct Answer
D:The capture shows reset direction, port and sequence in the affected flow. It tests the intended outcome because packet captures expose flags, timing and retransmissions not visible in simple ping.
Incorrect Answers
A:This test addresses a separate problem: A new fiber patch lead may be broken inside a wall but the optical route is undocumented.
B:The missing direct test is: The capture shows reset direction, port and sequence in the affected flow.
C:This observation is for a different condition: A network technician needs to locate which patch-panel port carries an unlabeled copper pair. It does not directly test the target outcome: A security engineer needs a packet-level record of a TCP reset sequence during a client-to-server failure.
Question 772
The original case was: A security engineer needs a packet-level record of a TCP reset sequence during a client-to-server failure. The requirement then changes: The task changes to collecting high-level traffic volume over a month. Which revised action BEST meets this new condition?
- Capture traffic with tcpdump or a protocol analyzer at an authorized observation point.
- The capture shows reset direction, port and sequence in the affected flow.
- Use flow telemetry and baseline monitoring rather than retaining every packet.
- Use a Wi-Fi antenna meter to decode a routed TCP reset on a wired LAN.
Explanation
Correct Answer
C:Flow metrics efficiently summarize usage without full payload storage. The revised requirement is: The task changes to collecting high-level traffic volume over a month. The appropriate action is: Use flow telemetry and baseline monitoring rather than retaining every packet.
Incorrect Answers
A:This is the original control. Packet captures expose flags, timing and retransmissions not visible in simple ping. It does not directly satisfy the revised requirement: The task changes to collecting high-level traffic volume over a month.
B:The capture shows reset direction, port and sequence in the affected flow. The current requirement is: The task changes to collecting high-level traffic volume over a month.
D:RF tools are not substitutes for packet protocol decoding. It remains inappropriate in the revised context.
Question 773
An operator wants to inspect the active routes on a Linux gateway after a VPN change. Which action MOST directly meets the stated networking requirement?
- Use ip route or the platform's routing table command and verify selected next hops.
- Inspect ARP or neighbor tables and local link reachability.
- Use a visual fault locator or suitable optical test equipment with proper safety precautions.
- Use arp alone and assume it lists every remote IP route.
Explanation
Correct Answer
A:Routing-table tools display forwarding candidates, prefix lengths and gateways. This specifically resolves: An operator wants to inspect the active routes on a Linux gateway after a VPN change.
Incorrect Answers
B:This action responds to a later condition: The VPN route is correct but a next-hop MAC remains unresolved. Correct routes still require local neighbor resolution.
C:This addresses another problem in objective 5.5: A new fiber patch lead may be broken inside a wall but the optical route is undocumented.
D:ARP stores local neighbor mappings rather than the full routing table. The suggested approach is: Use arp alone and assume it lists every remote IP route.
Question 774
An operator wants to inspect the active routes on a Linux gateway after a VPN change. A colleague instead suggests: Use arp alone and assume it lists every remote IP route. Which finding MOST specifically explains why that suggestion is unsuitable?
- ARP stores local neighbor mappings rather than the full routing table.
- Copper test pins cannot validate light propagation through fiber.
- Correct routes still require local neighbor resolution.
- Routing-table tools display forwarding candidates, prefix lengths and gateways.
Explanation
Correct Answer
A:ARP stores local neighbor mappings rather than the full routing table. This flaw directly concerns the proposed action: Use arp alone and assume it lists every remote IP route.
Incorrect Answers
B:This flaw concerns a different case in objective 5.5: A new fiber patch lead may be broken inside a wall but the optical route is undocumented. The current rejected proposal is: Use arp alone and assume it lists every remote IP route.
C:This rationale belongs to a later changed condition: The VPN route is correct but a next-hop MAC remains unresolved.
D:This explains why the recommended control works: Use ip route or the platform's routing table command and verify selected next hops.
Question 775
An operator wants to inspect the active routes on a Linux gateway after a VPN change. Which TWO entries together specify the appropriate corrective measure AND the strongest direct evidence that it works? (Select TWO.)
- Use arp alone and assume it lists every remote IP route.
- Use ip route or the platform's routing table command and verify selected next hops.
- The gateway routing output matches the intended VPN prefix and next hop.
- Inspect ARP or neighbor tables and local link reachability.
- Use a visual fault locator or suitable optical test equipment with proper safety precautions.
Explanation
Correct Answers
B:Correct control. Routing-table tools display forwarding candidates, prefix lengths and gateways. It addresses the present requirement: An operator wants to inspect the active routes on a Linux gateway after a VPN change.
C:Correct verification. The gateway routing output matches the intended VPN prefix and next hop. This demonstrates the outcome expected from: Use ip route or the platform's routing table command and verify selected next hops.
Incorrect Answers
A:Incorrect control. ARP stores local neighbor mappings rather than the full routing table. The inappropriate proposal is: Use arp alone and assume it lists every remote IP route.
D:This is a response to a different later requirement: The VPN route is correct but a next-hop MAC remains unresolved. Correct routes still require local neighbor resolution. It is not the original control-and-evidence pair.
E:This control fits another scenario in objective 5.5: A new fiber patch lead may be broken inside a wall but the optical route is undocumented. It does not directly verify or implement the present issue.
Question 776
The original case was: An operator wants to inspect the active routes on a Linux gateway after a VPN change. The requirement then changes: The VPN route is correct but a next-hop MAC remains unresolved. Which revised action BEST meets this new condition?
- Inspect ARP or neighbor tables and local link reachability.
- The gateway routing output matches the intended VPN prefix and next hop.
- Use arp alone and assume it lists every remote IP route.
- Use ip route or the platform's routing table command and verify selected next hops.
Explanation
Correct Answer
A:Correct routes still require local neighbor resolution. The revised requirement is: The VPN route is correct but a next-hop MAC remains unresolved. The appropriate action is: Inspect ARP or neighbor tables and local link reachability.
Incorrect Answers
B:The gateway routing output matches the intended VPN prefix and next hop. The current requirement is: The VPN route is correct but a next-hop MAC remains unresolved.
C:ARP stores local neighbor mappings rather than the full routing table. It remains inappropriate in the revised context.
D:This is the original control. Routing-table tools display forwarding candidates, prefix lengths and gateways. It does not directly satisfy the revised requirement: The VPN route is correct but a next-hop MAC remains unresolved.
Question 777
A network technician needs to locate which patch-panel port carries an unlabeled copper pair. Which action MOST directly meets the stated networking requirement?
- Inspect LLDP or CDP neighbor data with proper trust and device inventory checks.
- Use nslookup and infer the physical port from DNS results.
- Use a toner and probe or supported cable tracing equipment.
- Use a cable tester or certifier to validate pinout and pair mapping.
Explanation
Correct Answer
C:Cable toners help locate conductors through patch panels and walls. This specifically resolves: A network technician needs to locate which patch-panel port carries an unlabeled copper pair.
Incorrect Answers
A:This addresses another problem in objective 5.5: An engineer suspects an unknown switch is connected behind a port and wants to identify its neighbor.
B:Name resolution cannot identify unlabeled physical cable terminations. The suggested approach is: Use nslookup and infer the physical port from DNS results.
D:This action responds to a later condition: The cable is located but users report crossed wire pairs. A toner establishes location while a tester checks electrical correctness.
Question 778
A network technician needs to locate which patch-panel port carries an unlabeled copper pair. A colleague instead suggests: Use nslookup and infer the physical port from DNS results. Which finding MOST specifically explains why that suggestion is unsuitable?
- Internet throughput testing does not establish connected neighbor identity.
- Name resolution cannot identify unlabeled physical cable terminations.
- Cable toners help locate conductors through patch panels and walls.
- A toner establishes location while a tester checks electrical correctness.
Explanation
Correct Answer
B:Name resolution cannot identify unlabeled physical cable terminations. This flaw directly concerns the proposed action: Use nslookup and infer the physical port from DNS results.
Incorrect Answers
A:This flaw concerns a different case in objective 5.5: An engineer suspects an unknown switch is connected behind a port and wants to identify its neighbor. The current rejected proposal is: Use nslookup and infer the physical port from DNS results.
C:This explains why the recommended control works: Use a toner and probe or supported cable tracing equipment.
D:This rationale belongs to a later changed condition: The cable is located but users report crossed wire pairs.
Question 779
A network technician needs to locate which patch-panel port carries an unlabeled copper pair. After applying the solution 'Use a toner and probe or supported cable tracing equipment.', which observation MOST directly proves that the requirement was met?
- The affected VLAN and competing ports are identified and the loop corrected.
- Neighbor ID and local port agree with the verified topology diagram.
- The traced pair matches the expected wall outlet and switch port.
- Approval is recorded for 'Use a toner and probe or supported cable tracing equipment.' but no operational validation is performed.
Explanation
Correct Answer
C:The traced pair matches the expected wall outlet and switch port. It tests the intended outcome because cable toners help locate conductors through patch panels and walls.
Incorrect Answers
A:This test addresses a separate problem: A switch reports unexpected MAC flapping between uplink ports and the engineer must identify the source VLAN.
B:This observation is for a different condition: An engineer suspects an unknown switch is connected behind a port and wants to identify its neighbor. It does not directly test the target outcome: A network technician needs to locate which patch-panel port carries an unlabeled copper pair.
D:Approval alone does not demonstrate operating effectiveness. The missing direct test is: The traced pair matches the expected wall outlet and switch port.
Question 780
The original case was: A network technician needs to locate which patch-panel port carries an unlabeled copper pair. The requirement then changes: The cable is located but users report crossed wire pairs. Which revised action BEST meets this new condition?
- Use nslookup and infer the physical port from DNS results.
- Use a cable tester or certifier to validate pinout and pair mapping.
- Use a toner and probe or supported cable tracing equipment.
- The traced pair matches the expected wall outlet and switch port.
Explanation
Correct Answer
B:A toner establishes location while a tester checks electrical correctness. The revised requirement is: The cable is located but users report crossed wire pairs. The appropriate action is: Use a cable tester or certifier to validate pinout and pair mapping.
Incorrect Answers
A:Name resolution cannot identify unlabeled physical cable terminations. It remains inappropriate in the revised context.
C:This is the original control. Cable toners help locate conductors through patch panels and walls. It does not directly satisfy the revised requirement: The cable is located but users report crossed wire pairs.
D:The traced pair matches the expected wall outlet and switch port. The current requirement is: The cable is located but users report crossed wire pairs.