Cisco 500-220 Practice Test 45
Question 440
A Cisco Meraki deployment engineer must choose a safe configuration decision and one validating observation. A call center's video app should prefer a low-jitter ISP while large cloud backups can tolerate the other link. Which TWO steps together provide a targeted response with objective verification? Select TWO answers.
- Test captive portal redirection, permitted DNS/DHCP, Internet egress and denied internal subnet access.
- Correlate interface health, performance-class violations and observed traffic transition during controlled impairment.
- Configure application-specific traffic shaping and flow preference using observed WAN behavior and a limited change plan.
- Compare selected organization, networks, time period, report recipients and raw Dashboard activity for a known date.
- Inspect classification, configured rules, uplink loss/latency and a sampled flow before and after a test.
Explanation
Correct Answers
C:The targeted next step is: Configure application-specific traffic shaping and flow preference using observed WAN behavior and a limited change plan. The technical reason is: Uplink traffic shaping and performance-based preferences can influence selected flows but require accurately matched policies. A successful verification would use: Inspect classification, configured rules, uplink loss/latency and a sampled flow before and after a test.
E:The discriminating evidence is: Inspect classification, configured rules, uplink loss/latency and a sampled flow before and after a test.
Incorrect Answers
A:That evidence is relevant to the distinct Meraki subject of Guest Wi-Fi captive portal and traffic isolation, not the specific MX SD-WAN traffic preferences and shaping requirement.
B:That evidence is relevant to the distinct Meraki subject of Brownout versus hard WAN link-down detection, not the specific MX SD-WAN traffic preferences and shaping requirement.
D:That evidence is relevant to the distinct Meraki subject of Scheduled dashboard reports and audit interpretation, not the specific MX SD-WAN traffic preferences and shaping requirement.
Question 441
A Cisco Meraki deployment engineer investigates this operational case: An MX is configured to steer a SaaS application, but Dashboard flow analysis shows traffic following the generic rule. What is the most appropriate FIRST action to address the stated requirement? Select ONE best answer.
- Design separate guest, employee and IoT VLANs with deliberate inter-VLAN routing and firewall rules.
- Enable VPN participation for only authorized local subnets and verify advertised remote paths.
- Verify the administrator's organization role, MFA status and intended scope before granting access to a new network.
- Configure application-specific traffic shaping and flow preference using observed WAN behavior and a limited change plan.
Explanation
Correct Answer
D:The targeted next step is: Configure application-specific traffic shaping and flow preference using observed WAN behavior and a limited change plan.
Incorrect Answers
A:That action is relevant to the distinct Meraki subject of Network segmentation with VLANs and routed boundaries, not the specific MX SD-WAN traffic preferences and shaping requirement.
B:That action is relevant to the distinct Meraki subject of MX Auto VPN participation for selected VLANs, not the specific MX SD-WAN traffic preferences and shaping requirement.
C:That action is relevant to the distinct Meraki subject of Dashboard administrator authentication and least privilege, not the specific MX SD-WAN traffic preferences and shaping requirement.
Question 442
A peer reviewer evaluates the following Meraki case. An MX is configured to steer a SaaS application, but Dashboard flow analysis shows traffic following the generic rule. The proposed action is: Configure application-specific traffic shaping and flow preference using observed WAN behavior and a limited change plan. Which technical principle BEST supports this decision? Select ONE best answer.
- Apply the most aggressive low-rate shaping rule to every application to improve performance.
- A routing-capable MS requires configured L3 interfaces and routes to forward between subnets; VLAN creation is not sufficient.
- Uplink traffic shaping and performance-based preferences can influence selected flows but require accurately matched policies.
- The security appliance's network-layer firewall policy does not by itself complete endpoint EAP authentication at a switch or WLAN port.
Explanation
Correct Answer
C:Uplink traffic shaping and performance-based preferences can influence selected flows but require accurately matched policies. In this situation (An MX is configured to steer a SaaS application, but Dashboard flow analysis shows traffic following the generic rule.), it justifies the action: Configure application-specific traffic shaping and flow preference using observed WAN behavior and a limited change plan.
Incorrect Answers
A:This is an unsafe shortcut: Apply the most aggressive low-rate shaping rule to every application to improve performance. It does not establish the needed behavior: Uplink traffic shaping and performance-based preferences can influence selected flows but require accurately matched policies. The controlled response is: Configure application-specific traffic shaping and flow preference using observed WAN behavior and a limited change plan.
B:That principle is relevant to the distinct Meraki subject of MS switch routing interface and L3 reachability, not the specific MX SD-WAN traffic preferences and shaping requirement.
D:That principle is relevant to the distinct Meraki subject of MX access policies and switch-side authentication boundary, not the specific MX SD-WAN traffic preferences and shaping requirement.
Question 443
A Meraki support engineer must distinguish facts from assumptions. An MX is configured to steer a SaaS application, but Dashboard flow analysis shows traffic following the generic rule. Which diagnostic observation MOST DIRECTLY verifies the problem or requirement? Select ONE best answer.
- Correlate client IP, destination, service, matched MX rule and relevant threat or content event in Dashboard.
- Inspect classification, configured rules, uplink loss/latency and a sampled flow before and after a test.
- Compare partner endpoint, supported IPsec proposals, subnets and route policies with the native VPN topology.
- Compare assignment rules, managed app status, device OS support and a controlled installation attempt.
Explanation
Correct Answer
B:The discriminating evidence is: Inspect classification, configured rules, uplink loss/latency and a sampled flow before and after a test. Expected result: The critical application selects the appropriate healthy uplink without indiscriminately throttling all users.
Incorrect Answers
A:That evidence is relevant to the distinct Meraki subject of MX layer three and layer seven security filtering, not the specific MX SD-WAN traffic preferences and shaping requirement.
C:That evidence is relevant to the distinct Meraki subject of Non-Meraki peer versus native Auto VPN compatibility, not the specific MX SD-WAN traffic preferences and shaping requirement.
D:That evidence is relevant to the distinct Meraki subject of Managed app rollout and assignment scoping, not the specific MX SD-WAN traffic preferences and shaping requirement. For this scenario, the proper response is: Configure application-specific traffic shaping and flow preference using observed WAN behavior and a limited change plan. Verify it through: Inspect classification, configured rules, uplink loss/latency and a sampled flow before and after a test.
Question 444
An implementation lead needs a measurable acceptance criterion for a Meraki change. An MX is configured to steer a SaaS application, but Dashboard flow analysis shows traffic following the generic rule. The proposed validation is: Inspect classification, configured rules, uplink loss/latency and a sampled flow before and after a test. Which result BEST demonstrates that the intended requirement is satisfied? Select ONE best answer.
- The remote internal subnet becomes reachable through the correct next hop without diverting unrelated traffic.
- The service's actual policy or threat-detection cause is established and any exception is narrowly authorized.
- Real rogue devices are investigated while legitimate neighboring wireless networks are not disrupted without evidence.
- The critical application selects the appropriate healthy uplink without indiscriminately throttling all users.
Explanation
Correct Answer
D:The acceptance criterion is: The critical application selects the appropriate healthy uplink without indiscriminately throttling all users. Verify it using: Inspect classification, configured rules, uplink loss/latency and a sampled flow before and after a test.
Incorrect Answers
A:That outcome is relevant to the distinct Meraki subject of MX static routes to downstream layer three network, not the specific MX SD-WAN traffic preferences and shaping requirement. For this scenario, the proper response is: Configure application-specific traffic shaping and flow preference using observed WAN behavior and a limited change plan. Verify it through: Inspect classification, configured rules, uplink loss/latency and a sampled flow before and after a test.
B:That outcome is relevant to the distinct Meraki subject of Security Center threat event investigation and false positive, not the specific MX SD-WAN traffic preferences and shaping requirement.
C:That outcome is relevant to the distinct Meraki subject of MR Air Marshal threat and rogue SSID monitoring, not the specific MX SD-WAN traffic preferences and shaping requirement.
Question 445
A Meraki operations reviewer examines this case. An MX is configured to steer a SaaS application, but Dashboard flow analysis shows traffic following the generic rule. Which assumption is the MOST DIRECTLY relevant unsafe or technically wrong shortcut to reject here? Select ONE best answer.
- Turn on VPN for a public guest subnet simply because the corporate subnet needed inter-site access.
- Switch off IDS/IPS for the entire company because one upload is flagged by a suspicious signature.
- Erase a branch's known-good VLAN mapping merely because its configuration differs from a template screenshot.
- Apply the most aggressive low-rate shaping rule to every application to improve performance.
Explanation
Correct Answer
D:It conflicts with the relevant behavior: Uplink traffic shaping and performance-based preferences can influence selected flows but require accurately matched policies.
Incorrect Answers
A:That proposal is unsafe in its own context (the separate topic of MX Auto VPN participation for selected VLANs), but it is not the shortcut tied most directly to this incident. The case-specific fault to reject concerns MX SD-WAN traffic preferences and shaping: Apply the most aggressive low-rate shaping rule to every application to improve performance.
B:That proposal is unsafe in its own context (the separate topic of Security Center threat event investigation and false positive), but it is not the shortcut tied most directly to this incident. The case-specific fault to reject concerns MX SD-WAN traffic preferences and shaping: Apply the most aggressive low-rate shaping rule to every application to improve performance.
C:That proposal is unsafe in its own context (the separate topic of Template drift and configuration audit), but it is not the shortcut tied most directly to this incident. The case-specific fault to reject concerns MX SD-WAN traffic preferences and shaping: Apply the most aggressive low-rate shaping rule to every application to improve performance.
Question 446
A Cisco Meraki deployment engineer investigates this operational case: A school allows general HTTPS but denies a risky content category through its configured content policy. What is the most appropriate FIRST action to address the stated requirement? Select ONE best answer.
- Assign the appropriate MX VLAN interface, subnet and DHCP scope after confirming the routed LAN design.
- Replicate known-good supported switch port settings from a verified source without duplicating site-specific mistakes.
- Write targeted network and application controls and verify the specific matched traffic using Security Center and event logs.
- Read the current setting and keep a before/after audit when applying API configuration changes across many networks.
Explanation
Correct Answer
C:The targeted next step is: Write targeted network and application controls and verify the specific matched traffic using Security Center and event logs. The technical reason is: L3/L7 firewall and threat inspection may block different stages of a session; port reachability does not guarantee application permission.
Incorrect Answers
A:That action is relevant to the distinct Meraki subject of MX VLAN interfaces and DHCP configuration, not the specific MX layer three and layer seven security filtering requirement. For this scenario, the proper response is: Write targeted network and application controls and verify the specific matched traffic using Security Center and event logs.
B:That action is relevant to the distinct Meraki subject of MS configuration templates and switch port cloning, not the specific MX layer three and layer seven security filtering requirement. For this scenario, the proper response is: Write targeted network and application controls and verify the specific matched traffic using Security Center and event logs.
D:That action is relevant to the distinct Meraki subject of Dashboard API idempotent change and preflight audit, not the specific MX layer three and layer seven security filtering requirement.
Question 447
A peer reviewer evaluates the following Meraki case. A school allows general HTTPS but denies a risky content category through its configured content policy. The proposed action is: Write targeted network and application controls and verify the specific matched traffic using Security Center and event logs. Which technical principle BEST supports this decision? Select ONE best answer.
- L3/L7 firewall and threat inspection may block different stages of a session; port reachability does not guarantee application permission.
- Organization and network administrator privileges are not equivalent; authenticating to Dashboard alone does not imply permission to edit all networks.
- Uplink traffic shaping and performance-based preferences can influence selected flows but require accurately matched policies.
- VLANs separate layer-2 broadcast domains, while access between them requires a suitable routed and policy-controlled boundary.
Explanation
Correct Answer
A:L3/L7 firewall and threat inspection may block different stages of a session; port reachability does not guarantee application permission. In this situation (A school allows general HTTPS but denies a risky content category through its configured content policy.), it justifies the action: Write targeted network and application controls and verify the specific matched traffic using Security Center and event logs.
Incorrect Answers
B:That principle is relevant to the distinct Meraki subject of Dashboard administrator authentication and least privilege, not the specific MX layer three and layer seven security filtering requirement.
C:That principle is relevant to the distinct Meraki subject of MX SD-WAN traffic preferences and shaping, not the specific MX layer three and layer seven security filtering requirement.
D:That principle is relevant to the distinct Meraki subject of Network segmentation with VLANs and routed boundaries, not the specific MX layer three and layer seven security filtering requirement.
Question 448
A Meraki support engineer must distinguish facts from assumptions. A school allows general HTTPS but denies a risky content category through its configured content policy. Which diagnostic observation MOST DIRECTLY verifies the problem or requirement? Select ONE best answer.
- Verify one authorized managed client, one unauthorized client and their resulting VLAN and firewall policy.
- Audit network role assignments and test event viewing separately from actual change permissions.
- Compare edge access policy, RADIUS response, assigned VLAN and MX permitted subnet flow.
- Correlate client IP, destination, service, matched MX rule and relevant threat or content event in Dashboard.
Explanation
Correct Answer
D:The discriminating evidence is: Correlate client IP, destination, service, matched MX rule and relevant threat or content event in Dashboard. Expected result: Approved application traffic succeeds while prohibited categories and services remain blocked and auditable.
Incorrect Answers
A:That evidence is relevant to the distinct Meraki subject of Enterprise SSID design for authentication and segmentation, not the specific MX layer three and layer seven security filtering requirement.
B:That evidence is relevant to the distinct Meraki subject of Network-level privileges and separation of duties, not the specific MX layer three and layer seven security filtering requirement.
C:That evidence is relevant to the distinct Meraki subject of MX access policies and switch-side authentication boundary, not the specific MX layer three and layer seven security filtering requirement. For this scenario, the proper response is: Write targeted network and application controls and verify the specific matched traffic using Security Center and event logs.
Question 449
An implementation lead needs a measurable acceptance criterion for a Meraki change. A school allows general HTTPS but denies a risky content category through its configured content policy. The proposed validation is: Correlate client IP, destination, service, matched MX rule and relevant threat or content event in Dashboard. Which result BEST demonstrates that the intended requirement is satisfied? Select ONE best answer.
- The remote internal subnet becomes reachable through the correct next hop without diverting unrelated traffic.
- Approved application traffic succeeds while prohibited categories and services remain blocked and auditable.
- The root cause is classified as RF, association, authentication or upstream network issue with confirming tests.
- The branch receives shared security settings while retaining its correct local VLAN and addressing requirements.
Explanation
Correct Answer
B:The acceptance criterion is: Approved application traffic succeeds while prohibited categories and services remain blocked and auditable. Verify it using: Correlate client IP, destination, service, matched MX rule and relevant threat or content event in Dashboard.
Incorrect Answers
A:That outcome is relevant to the distinct Meraki subject of MX static routes to downstream layer three network, not the specific MX layer three and layer seven security filtering requirement. For this scenario, the proper response is: Write targeted network and application controls and verify the specific matched traffic using Security Center and event logs.
C:That outcome is relevant to the distinct Meraki subject of MR wireless RF interference and roaming diagnosis, not the specific MX layer three and layer seven security filtering requirement.
D:That outcome is relevant to the distinct Meraki subject of Configuration templates and network binding, not the specific MX layer three and layer seven security filtering requirement.
Question 450
A Cisco Meraki deployment engineer must choose a safe configuration decision and one validating observation. A school allows general HTTPS but denies a risky content category through its configured content policy. Which TWO steps together provide a targeted response with objective verification? Select TWO answers.
- Replicate known-good supported switch port settings from a verified source without duplicating site-specific mistakes.
- Select suitable Meraki Insight application and WAN metrics to determine whether delay occurs in the WAN or at the application.
- Correlate client IP, destination, service, matched MX rule and relevant threat or content event in Dashboard.
- Write targeted network and application controls and verify the specific matched traffic using Security Center and event logs.
- Map the topology's role requirements to device inventory, physical uplinks and Dashboard product tabs.
Explanation
Correct Answers
C:The discriminating evidence is: Correlate client IP, destination, service, matched MX rule and relevant threat or content event in Dashboard.
D:The targeted next step is: Write targeted network and application controls and verify the specific matched traffic using Security Center and event logs. The technical reason is: L3/L7 firewall and threat inspection may block different stages of a session; port reachability does not guarantee application permission. A successful verification would use: Correlate client IP, destination, service, matched MX rule and relevant threat or content event in Dashboard.
Incorrect Answers
A:That action is relevant to the distinct Meraki subject of MS configuration templates and switch port cloning, not the specific MX layer three and layer seven security filtering requirement. For this scenario, the proper response is: Write targeted network and application controls and verify the specific matched traffic using Security Center and event logs. Verify it through: Correlate client IP, destination, service, matched MX rule and relevant threat or content event in Dashboard.
B:That action is relevant to the distinct Meraki subject of Meraki Insight application health and WAN visibility, not the specific MX layer three and layer seven security filtering requirement.
E:That evidence is relevant to the distinct Meraki subject of Product family capabilities and integrated Dashboard view, not the specific MX layer three and layer seven security filtering requirement.