Cisco 350-601 Practice Test 17
Question 160
A tenant VM migrates between VTEPs but the receiving leaf continues using a stale remote host location. The observed failure is: stale or missing type-2 information misdirects VXLAN traffic after an endpoint moves. What is the BEST controlled recovery once this failure is recognized?
- The controlled remediation is to assume underlay IP ping alone proves MAC reachability.
- The controlled remediation is to replace all type-2 routes with OSPF network statements for tenant MAC addresses.
- The controlled remediation is to use a storage FCID as the destination VXLAN VTEP.
- The controlled remediation is to restore advertisements and endpoint learning, then verify corrected remote VTEP and MAC mobility state.
Explanation
Correct Answer
D:Validate against EVPN type-2 routes, MAC mobility sequence, VTEP next hops, and active endpoint MAC table. EVPN type-2 reachability signals overlay MAC and optional IP bindings and supports endpoint mobility.
Incorrect Answers
A:Assume underlay IP ping alone proves MAC reachability. This would not reliably restore service after the stated fault. Stale or missing type-2 information misdirects VXLAN traffic after an endpoint moves. The controlled recovery is to restore advertisements and endpoint learning, then verify corrected remote VTEP and MAC mobility state.
B:Replace all type-2 routes with OSPF network statements for tenant MAC addresses. This would not reliably restore service after the stated fault. Stale or missing type-2 information misdirects VXLAN traffic after an endpoint moves. The controlled recovery is to restore advertisements and endpoint learning, then verify corrected remote VTEP and MAC mobility state.
C:Use a storage FCID as the destination VXLAN VTEP. This would not reliably restore service after the stated fault. Stale or missing type-2 information misdirects VXLAN traffic after an endpoint moves. The controlled recovery is to restore advertisements and endpoint learning, then verify corrected remote VTEP and MAC mobility state.
Question 161
An L3 VNI can carry tenant endpoint MACs but a remote tenant subnet is missing from the receiving VRF. What is the BEST supported implementation or corrective action?
- Verify and restore EVPN type-5 IP-prefix advertisement and associated L3 VNI or VRF route-target import.
- Disable all host addressing to force prefix routes to appear.
- Set every tenant to the default VRF without isolation planning.
- Change a SAN VSAN number instead of checking EVPN prefix routes.
Explanation
Correct Answer
A:This directly addresses EVPN type-5 prefix reachability because type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity. Confirm the change against EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
Incorrect Answers
B:Layer 2 endpoint learning does not automatically provide every required routed tenant prefix. The relevant correction is to verify and restore EVPN type-5 IP-prefix advertisement and associated L3 VNI or VRF route-target import.
C:Set every tenant to the default VRF without isolation planning. The proposed change targets the wrong mechanism or lacks essential validation. Type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity. Relevant evidence is EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
D:Layer 2 endpoint learning does not automatically provide every required routed tenant prefix. The appropriate action remains to verify and restore EVPN type-5 IP-prefix advertisement and associated L3 VNI or VRF route-target import.
Question 162
An L3 VNI can carry tenant endpoint MACs but a remote tenant subnet is missing from the receiving VRF. Which evidence BEST verifies the intended technical behavior?
- One successful ping to an unrelated management address.
- EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
- An interface description without the effective peer or VXLAN policy.
- A healthy optical light without checking protocol neighbors or forwarding entries.
Explanation
Correct Answer
B:These observations test the actual EVPN type-5 prefix reachability mechanism rather than a superficial management status. Type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity.
Incorrect Answers
A:This information cannot independently verify EVPN type-5 prefix reachability. The decisive records instead include EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
C:This information cannot independently verify EVPN type-5 prefix reachability. Type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity.
D:This information cannot independently verify EVPN type-5 prefix reachability. A healthy optical light without checking protocol neighbors or forwarding entries.
Question 163
An L3 VNI can carry tenant endpoint MACs but a remote tenant subnet is missing from the receiving VRF. Which principle BEST explains why the recommended solution is appropriate?
- A device description always determines actual forwarding policy regardless of running configuration.
- All control-plane protocols exchange state automatically after a cable is inserted.
- Type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity.
- Configuration differences between peer switches cannot affect network traffic.
Explanation
Correct Answer
C:Validation depends on EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution. This explains why the most appropriate response is to verify and restore EVPN type-5 IP-prefix advertisement and associated L3 VNI or VRF route-target import.
Incorrect Answers
A:A device description always determines actual forwarding policy regardless of running configuration. This is an incorrect generalization for EVPN type-5 prefix reachability. The applicable technical behavior is that type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity. The operator should verify EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
B:All control-plane protocols exchange state automatically after a cable is inserted. This is an incorrect generalization for EVPN type-5 prefix reachability. The applicable technical behavior is that type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity. The operator should verify EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
D:Configuration differences between peer switches cannot affect network traffic. This is an incorrect generalization for EVPN type-5 prefix reachability. The applicable technical behavior is that type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity. The operator should verify EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
Question 164
An L3 VNI can carry tenant endpoint MACs but a remote tenant subnet is missing from the receiving VRF. Assume an engineer instead chooses to disable all host addressing to force prefix routes to appear. What is the MOST significant failure introduced by that shortcut?
- The only consequence of the wrong change is a different device description.
- Verifying topology after maintenance automatically creates a switching loop.
- The defect exists solely because the engineer documented the change.
- Layer 2 endpoint learning does not automatically provide every required routed tenant prefix.
Explanation
Correct Answer
D:The proper corrective action is to verify and restore EVPN type-5 IP-prefix advertisement and associated L3 VNI or VRF route-target import. Type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity.
Incorrect Answers
A:The only consequence of the wrong change is a different device description. This does not explain the actual EVPN type-5 prefix reachability defect after the shortcut. The meaningful failure is that layer 2 endpoint learning does not automatically provide every required routed tenant prefix. The relevant evidence is EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
B:Verifying topology after maintenance automatically creates a switching loop. This does not explain the actual EVPN type-5 prefix reachability defect after the shortcut. The meaningful failure is that layer 2 endpoint learning does not automatically provide every required routed tenant prefix. The relevant evidence is EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
C:The defect exists solely because the engineer documented the change. This does not explain the actual EVPN type-5 prefix reachability defect after the shortcut. The meaningful failure is that layer 2 endpoint learning does not automatically provide every required routed tenant prefix. The relevant evidence is EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
Question 165
An L3 VNI can carry tenant endpoint MACs but a remote tenant subnet is missing from the receiving VRF. The observed failure is: layer 2 endpoint learning does not automatically provide every required routed tenant prefix. What is the BEST controlled recovery once this failure is recognized?
- Correct prefix export and import policy and test inter-subnet forwarding in the tenant VRF.
- Set every tenant to the default VRF without isolation planning.
- Change a SAN VSAN number instead of checking EVPN prefix routes.
- Disable all host addressing to force prefix routes to appear.
Explanation
Correct Answer
A:This addresses the observable fault while preserving a check of the expected result. Type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity.
Incorrect Answers
B:Set every tenant to the default VRF without isolation planning. This would not reliably restore service after the stated fault. Layer 2 endpoint learning does not automatically provide every required routed tenant prefix. The controlled recovery is to correct prefix export and import policy and test inter-subnet forwarding in the tenant VRF.
C:Change a SAN VSAN number instead of checking EVPN prefix routes. This would not reliably restore service after the stated fault. Layer 2 endpoint learning does not automatically provide every required routed tenant prefix. The controlled recovery is to correct prefix export and import policy and test inter-subnet forwarding in the tenant VRF.
D:Disable all host addressing to force prefix routes to appear. This would not reliably restore service after the stated fault. Layer 2 endpoint learning does not automatically provide every required routed tenant prefix. The controlled recovery is to correct prefix export and import policy and test inter-subnet forwarding in the tenant VRF.
Question 166
Two data center sites advertise EVPN prefix routes, but one leaf lacks the imported IP prefix despite reachable VTEP loopbacks. Which configuration decision MOST directly resolves the issue?
- On this affected device, the engineer should set every tenant to the default VRF without isolation planning.
- On this affected device, the engineer should verify and restore EVPN type-5 IP-prefix advertisement and associated L3 VNI or VRF route-target import.
- On this affected device, the engineer should change a SAN VSAN number instead of checking EVPN prefix routes.
- On this affected device, the engineer should disable all host addressing to force prefix routes to appear.
Explanation
Correct Answer
B:This directly addresses EVPN type-5 prefix reachability because type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity. In the given case, two data center sites advertise EVPN prefix routes, but one leaf lacks the imported IP prefix despite reachable VTEP loopbacks.
Incorrect Answers
A:Set every tenant to the default VRF without isolation planning. The proposed change targets the wrong mechanism or lacks essential validation. Type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity. Relevant evidence is EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
C:Layer 2 endpoint learning does not automatically provide every required routed tenant prefix. Change a SAN VSAN number instead of checking EVPN prefix routes.
D:Layer 2 endpoint learning does not automatically provide every required routed tenant prefix. Disable all host addressing to force prefix routes to appear.
Question 167
Two data center sites advertise EVPN prefix routes, but one leaf lacks the imported IP prefix despite reachable VTEP loopbacks. What should the engineer inspect to confirm the actual state?
- For this deployment, examine an up management interface without the relevant routing or forwarding table.
- For this deployment, examine one successful ping to an unrelated management address.
- For this deployment, examine EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
- For this deployment, examine an interface description without the effective peer or VXLAN policy.
Explanation
Correct Answer
C:These observations test the actual EVPN type-5 prefix reachability mechanism rather than a superficial management status. They should be checked after verify and restore EVPN type-5 IP-prefix advertisement and associated L3 VNI or VRF route-target import.
Incorrect Answers
A:This information cannot independently verify EVPN type-5 prefix reachability. An up management interface without the relevant routing or forwarding table.
B:This information cannot independently verify EVPN type-5 prefix reachability. In the given case, two data center sites advertise EVPN prefix routes, but one leaf lacks the imported IP prefix despite reachable VTEP loopbacks.
D:This information cannot independently verify EVPN type-5 prefix reachability. An interface description without the effective peer or VXLAN policy.
Question 168
Two data center sites advertise EVPN prefix routes, but one leaf lacks the imported IP prefix despite reachable VTEP loopbacks. What technical behavior underlies the correct decision?
- For this condition, the applicable principle is that configuration differences between peer switches cannot affect network traffic.
- For this condition, the applicable principle is that a device description always determines actual forwarding policy regardless of running configuration.
- For this condition, the applicable principle is that physical link carrier guarantees all overlay and routing states are correct.
- For this condition, the applicable principle is that type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity.
Explanation
Correct Answer
D:Validation depends on EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
Incorrect Answers
A:Configuration differences between peer switches cannot affect network traffic. This is an incorrect generalization for EVPN type-5 prefix reachability. The applicable technical behavior is that type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity. The operator should verify EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
B:A device description always determines actual forwarding policy regardless of running configuration. This is an incorrect generalization for EVPN type-5 prefix reachability. The applicable technical behavior is that type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity. The operator should verify EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
C:Physical link carrier guarantees all overlay and routing states are correct. This is an incorrect generalization for EVPN type-5 prefix reachability. The applicable technical behavior is that type-5 EVPN routes distribute IP prefix reachability for routed overlay connectivity. The operator should verify EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
Question 169
Two data center sites advertise EVPN prefix routes, but one leaf lacks the imported IP prefix despite reachable VTEP loopbacks. Assume an engineer instead chooses to disable all host addressing to force prefix routes to appear. Which resulting risk or fault should the reviewer identify?
- The resulting defect is that layer 2 endpoint learning does not automatically provide every required routed tenant prefix.
- The resulting defect is that the defect exists solely because the engineer documented the change.
- The resulting defect is that preserving neighbor-state evidence is itself the source of the observed outage.
- The resulting defect is that verifying topology after maintenance automatically creates a switching loop.
Explanation
Correct Answer
A:The proper corrective action is to verify and restore EVPN type-5 IP-prefix advertisement and associated L3 VNI or VRF route-target import. That is the direct consequence of choosing the misleading shortcut.
Incorrect Answers
B:The defect exists solely because the engineer documented the change. This does not explain the actual EVPN type-5 prefix reachability defect after the shortcut. The meaningful failure is that layer 2 endpoint learning does not automatically provide every required routed tenant prefix. The relevant evidence is EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
C:Preserving neighbor-state evidence is itself the source of the observed outage. This does not explain the actual EVPN type-5 prefix reachability defect after the shortcut. The meaningful failure is that layer 2 endpoint learning does not automatically provide every required routed tenant prefix. The relevant evidence is EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
D:Verifying topology after maintenance automatically creates a switching loop. This does not explain the actual EVPN type-5 prefix reachability defect after the shortcut. The meaningful failure is that layer 2 endpoint learning does not automatically provide every required routed tenant prefix. The relevant evidence is EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
Question 170
Two data center sites advertise EVPN prefix routes, but one leaf lacks the imported IP prefix despite reachable VTEP loopbacks. The observed failure is: layer 2 endpoint learning does not automatically provide every required routed tenant prefix. Which remediation most directly restores the intended behavior?
- The controlled remediation is to change a SAN VSAN number instead of checking EVPN prefix routes.
- The controlled remediation is to correct prefix export and import policy and test inter-subnet forwarding in the tenant VRF.
- The controlled remediation is to disable all host addressing to force prefix routes to appear.
- The controlled remediation is to set every tenant to the default VRF without isolation planning.
Explanation
Correct Answer
B:This addresses the observable fault while preserving a check of the expected result. Validate against EVPN type-5 advertisements, L3 VNI association, VRF route table, and next-hop resolution.
Incorrect Answers
A:Change a SAN VSAN number instead of checking EVPN prefix routes. This would not reliably restore service after the stated fault. Layer 2 endpoint learning does not automatically provide every required routed tenant prefix. The controlled recovery is to correct prefix export and import policy and test inter-subnet forwarding in the tenant VRF.
C:Disable all host addressing to force prefix routes to appear. This would not reliably restore service after the stated fault. Layer 2 endpoint learning does not automatically provide every required routed tenant prefix. The controlled recovery is to correct prefix export and import policy and test inter-subnet forwarding in the tenant VRF.
D:Set every tenant to the default VRF without isolation planning. This would not reliably restore service after the stated fault. Layer 2 endpoint learning does not automatically provide every required routed tenant prefix. The controlled recovery is to correct prefix export and import policy and test inter-subnet forwarding in the tenant VRF.