Cisco 300-610 Practice Test 30
Question 290
At a mission-critical UCS blade installation, a post-incident design review focuses on preventing: A UCS database server has two virtual HBAs but both paths terminate on fabric A and lose all storage when it goes down. The team needs a defensible design decision rather than a vendor feature checklist. Which continuing design control best prevents the same problem from recurring?
- Require dual-fabric path tests before production datastore activation.
- Review backup-fabric capacity before adding demanding workloads.
- Re-run SAN oversubscription analysis when new host profiles increase I/O demand.
- Document FC-mode and NPIV dependencies during fabric-switch replacement.
Explanation
Correct Answer
A:The most relevant ongoing safeguard is: Require dual-fabric path tests before production datastore activation. The risk it addresses is: A UCS database server has two virtual HBAs but both paths terminate on fabric A and lose all storage when it goes down. This check is tied to the technical principle: SAN multipath resiliency relies on independent initiator paths, FI fabrics, switches and target portals, not merely on two WWPNs. The immediate correction remains: Allocate one supported vHBA per fabric and validate operating-system MPIO and SAN zoning end to end. Periodically validate the safeguard through two different observations. Trace each vHBA WWPN through separate fabric switches Test a controlled fabric A loss while observing datastore I/O. The continuing acceptance target is: Storage remains accessible through the surviving SAN fabric without an unsupported failover mechanism.
Incorrect Answers
B:This is a continuing control for storage path failover with asymmetric bandwidth; its underlying principle is: Availability paths also require degraded-mode performance planning; two physically diverse links alone do not guarantee equal capacity. The recurring risk here is different: A UCS database server has two virtual HBAs but both paths terminate on fabric A and lose all storage when it goes down. The appropriate ongoing control must prevent recurrence of that particular failure, not just the separate issue of: Two SAN fabrics exist but one has much less bandwidth, so losing the primary fabric creates unacceptable I/O latency. The intended long-term acceptance condition remains: Storage remains accessible through the surviving SAN fabric without an unsupported failover mechanism.
C:This is a continuing control for fc uplink throughput for storage; its underlying principle is: vHBA virtual link rates do not create physical FC capacity; SAN fabric uplink bandwidth and oversubscription must be budgeted. The recurring risk here is different: A UCS database server has two virtual HBAs but both paths terminate on fabric A and lose all storage when it goes down. The appropriate ongoing control must prevent recurrence of that particular failure, not just the separate issue of: A UCS fabric adds many high-speed vHBAs but uses only one slow FC uplink and experiences queueing at peak backup time. The intended long-term acceptance condition remains: Storage remains accessible through the surviving SAN fabric without an unsupported failover mechanism.
D:This is a continuing control for fc end-host npv uplink identity; its underlying principle is: In FC end-host mode, UCS FI behaves as an NPV gateway with upstream NPIV-capable fabric switches, not as a fabric-merging FC core. The recurring risk here is different: A UCS database server has two virtual HBAs but both paths terminate on fabric A and lose all storage when it goes down. The appropriate ongoing control must prevent recurrence of that particular failure, not just the separate issue of: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The intended long-term acceptance condition remains: Storage remains accessible through the surviving SAN fabric without an unsupported failover mechanism.
Question 291
At a mission-critical UCS blade installation, during a controlled design review, the team discovers: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The maintenance plan must not disrupt unrelated tenants. Which design correction most directly addresses this specific failure or requirement?
- Allocate one supported vHBA per fabric and validate operating-system MPIO and SAN zoning end to end.
- Select supported FC mode and connect each fabric to suitable NPIV-capable upstream switches with correct VSAN connectivity.
- Correct the approved FCoE VLAN-to-VSAN association and preserve tenant SAN isolation.
- Provide dedicated and consistently marked storage queues with appropriate DCB/QoS while isolating other traffic classes.
Explanation
Correct Answer
B:The relevant failure is: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The technical distinction is: In FC end-host mode, UCS FI behaves as an NPV gateway with upstream NPIV-capable fabric switches, not as a fabric-merging FC core. The targeted correction is: Select supported FC mode and connect each fabric to suitable NPIV-capable upstream switches with correct VSAN connectivity. Before changing the design, check two independent observations. Inspect FI FC mode and upstream switch NPIV state Verify vHBA virtual N-port login through the intended upstream fabric. Accept the change only if: Each vHBA logs into the correct isolated SAN fabric and receives authorized storage zoning.
Incorrect Answers
A:This action targets dual-fabric fibre channel san paths, where the mechanism is: SAN multipath resiliency relies on independent initiator paths, FI fabrics, switches and target portals, not merely on two WWPNs. That is a separate condition from the problem in this question: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. Even a successful repair of the alternative would not establish the required result: Each vHBA logs into the correct isolated SAN fabric and receives authorized storage zoning. The applicable design change must address the diagnosed mechanism of the stated case, not the neighboring design problem.
C:This action targets fcoe vlan versus san vsan mapping, where the mechanism is: FCoE uses an appropriate Ethernet transport and VLAN mapping while FC zoning and fabric membership remain VSAN scoped. That is a separate condition from the problem in this question: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. Even a successful repair of the alternative would not establish the required result: Each vHBA logs into the correct isolated SAN fabric and receives authorized storage zoning. The applicable design change must address the diagnosed mechanism of the stated case, not the neighboring design problem.
D:This action targets fcoe no-drop priority isolation, where the mechanism is: FCoE storage transport needs coherent supported Data Center Bridging QoS, commonly including PFC for assigned storage traffic classes. That is a separate condition from the problem in this question: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. Even a successful repair of the alternative would not establish the required result: Each vHBA logs into the correct isolated SAN fabric and receives authorized storage zoning. The applicable design change must address the diagnosed mechanism of the stated case, not the neighboring design problem.
Question 292
At an Intersight-managed UCS cluster, before changing the fabric, the team observes: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. Acceptance requires evidence from the running system, not just the saved design. Which pair of observations most directly tests the proposed diagnosis before a change?
- Inspect FCoE VLAN and VSAN bindings at FI and upstream switch; verify fabric login and target discovery on the correct VSAN.
- Inspect FI FC mode and upstream switch NPIV state; verify vHBA virtual N-port login through the intended upstream fabric.
- Inspect FCoE priority/CoS at FI and switch; correlate PFC or drop counters with storage path resets under stress.
- Trace each vHBA WWPN through separate fabric switches; test a controlled fabric A loss while observing datastore I/O.
Explanation
Correct Answer
B:The first observation is: Inspect FI FC mode and upstream switch NPIV state The independent second observation is: Verify vHBA virtual N-port login through the intended upstream fabric. Together they test the proposed diagnosis of this incident: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The underlying technical principle is: In FC end-host mode, UCS FI behaves as an NPV gateway with upstream NPIV-capable fabric switches, not as a fabric-merging FC core. If those checks confirm it, the appropriate next action is: Select supported FC mode and connect each fabric to suitable NPIV-capable upstream switches with correct VSAN connectivity. The expected measurable result is: Each vHBA logs into the correct isolated SAN fabric and receives authorized storage zoning.
Incorrect Answers
A:These observations investigate fcoe vlan versus san vsan mapping; they would be useful if the symptoms were: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. That alternative rests on the principle: FCoE uses an appropriate Ethernet transport and VLAN mapping while FC zoning and fabric membership remain VSAN scoped. The question instead asks for evidence about: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The discriminating observations here are: Inspect FI FC mode and upstream switch NPIV state Verify vHBA virtual N-port login through the intended upstream fabric.
C:These observations investigate fcoe no-drop priority isolation; they would be useful if the symptoms were: An Ethernet network combines FCoE SAN traffic with lossy application bursts but does not reserve appropriate lossless treatment. That alternative rests on the principle: FCoE storage transport needs coherent supported Data Center Bridging QoS, commonly including PFC for assigned storage traffic classes. The question instead asks for evidence about: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The discriminating observations here are: Inspect FI FC mode and upstream switch NPIV state Verify vHBA virtual N-port login through the intended upstream fabric.
D:These observations investigate dual-fabric fibre channel san paths; they would be useful if the symptoms were: A UCS database server has two virtual HBAs but both paths terminate on fabric A and lose all storage when it goes down. That alternative rests on the principle: SAN multipath resiliency relies on independent initiator paths, FI fabrics, switches and target portals, not merely on two WWPNs. The question instead asks for evidence about: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The discriminating observations here are: Inspect FI FC mode and upstream switch NPIV state Verify vHBA virtual N-port login through the intended upstream fabric.
Question 293
At a dual-fabric virtualization host estate, the data-center team needs to explain this behavior: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. One component outage must remain inside the agreed availability budget. Which engineering principle best explains the observed behavior?
- In FC end-host mode, UCS FI behaves as an NPV gateway with upstream NPIV-capable fabric switches, not as a fabric-merging FC core.
- Direct-attached FC storage and FCoE port roles are platform/release dependent and must be verified against specific Cisco FI and array compatibility.
- SAN multipath resiliency relies on independent initiator paths, FI fabrics, switches and target portals, not merely on two WWPNs.
- vHBA virtual link rates do not create physical FC capacity; SAN fabric uplink bandwidth and oversubscription must be budgeted.
Explanation
Correct Answer
A:The controlling technical principle is: In FC end-host mode, UCS FI behaves as an NPV gateway with upstream NPIV-capable fabric switches, not as a fabric-merging FC core. This matters because the reported design failure is: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The first diagnostic check is: Inspect FI FC mode and upstream switch NPIV state The independent check is: Verify vHBA virtual N-port login through the intended upstream fabric. These facts support the targeted intervention: Select supported FC mode and connect each fabric to suitable NPIV-capable upstream switches with correct VSAN connectivity. Confirm that the resulting design meets this condition: Each vHBA logs into the correct isolated SAN fabric and receives authorized storage zoning.
Incorrect Answers
B:The offered principle describes direct-attached fc storage support boundaries: Direct-attached FC storage and FCoE port roles are platform/release dependent and must be verified against specific Cisco FI and array compatibility. That is useful for a distinct incident, such as: A design assumes every UCS FI and storage array combination supports direct FC target attachment in the same way as an external SAN switch. It does not account for the reported failure: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The governing principle in this situation is: In FC end-host mode, UCS FI behaves as an NPV gateway with upstream NPIV-capable fabric switches, not as a fabric-merging FC core.
C:The offered principle describes dual-fabric fibre channel san paths: SAN multipath resiliency relies on independent initiator paths, FI fabrics, switches and target portals, not merely on two WWPNs. That is useful for a distinct incident, such as: A UCS database server has two virtual HBAs but both paths terminate on fabric A and lose all storage when it goes down. It does not account for the reported failure: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The governing principle in this situation is: In FC end-host mode, UCS FI behaves as an NPV gateway with upstream NPIV-capable fabric switches, not as a fabric-merging FC core.
D:The offered principle describes fc uplink throughput for storage: vHBA virtual link rates do not create physical FC capacity; SAN fabric uplink bandwidth and oversubscription must be budgeted. That is useful for a distinct incident, such as: A UCS fabric adds many high-speed vHBAs but uses only one slow FC uplink and experiences queueing at peak backup time. It does not account for the reported failure: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The governing principle in this situation is: In FC end-host mode, UCS FI behaves as an NPV gateway with upstream NPIV-capable fabric switches, not as a fabric-merging FC core.
Question 294
At a Cisco UCS domain expansion, the team completed an authorized repair for: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The architect must preserve the intended failure domains. Which measured result most directly proves the original requirement is satisfied?
- The selected storage topology provides documented, supported connectivity and redundancy.
- Host initiators discover only approved targets through the intended SAN domain.
- Storage remains accessible through the surviving SAN fabric without an unsupported failover mechanism.
- Each vHBA logs into the correct isolated SAN fabric and receives authorized storage zoning.
Explanation
Correct Answer
D:The relevant measurable success criterion is: Each vHBA logs into the correct isolated SAN fabric and receives authorized storage zoning. It addresses the original reported defect: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. A saved design or configuration command alone does not establish that outcome. Observe the affected system in two independent ways: Inspect FI FC mode and upstream switch NPIV state Verify vHBA virtual N-port login through the intended upstream fabric. The correction being evaluated is: Select supported FC mode and connect each fabric to suitable NPIV-capable upstream switches with correct VSAN connectivity. The underlying reason that correction matters is: In FC end-host mode, UCS FI behaves as an NPV gateway with upstream NPIV-capable fabric switches, not as a fabric-merging FC core.
Incorrect Answers
A:This metric would help validate a correction to direct-attached fc storage support boundaries, rather than the original reported issue. The other issue is: A design assumes every UCS FI and storage array combination supports direct FC target attachment in the same way as an external SAN switch. Here the defect to be resolved is: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The expected measurable outcome for the actual incident is: Each vHBA logs into the correct isolated SAN fabric and receives authorized storage zoning. A positive result for the other service would not prove this requirement is met.
B:This metric would help validate a correction to fcoe vlan versus san vsan mapping, rather than the original reported issue. The other issue is: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. Here the defect to be resolved is: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The expected measurable outcome for the actual incident is: Each vHBA logs into the correct isolated SAN fabric and receives authorized storage zoning. A positive result for the other service would not prove this requirement is met.
C:This metric would help validate a correction to dual-fabric fibre channel san paths, rather than the original reported issue. The other issue is: A UCS database server has two virtual HBAs but both paths terminate on fabric A and lose all storage when it goes down. Here the defect to be resolved is: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The expected measurable outcome for the actual incident is: Each vHBA logs into the correct isolated SAN fabric and receives authorized storage zoning. A positive result for the other service would not prove this requirement is met.
Question 295
At a modular X-Series compute design, the architecture standards group considers the recurring risk: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The team needs a defensible design decision rather than a vendor feature checklist. Which continuing design control best prevents the same problem from recurring?
- Require dual-fabric path tests before production datastore activation.
- Audit DCB maps whenever FI uplink trunk policies change.
- Document FC-mode and NPIV dependencies during fabric-switch replacement.
- Re-run SAN oversubscription analysis when new host profiles increase I/O demand.
Explanation
Correct Answer
C:The most relevant ongoing safeguard is: Document FC-mode and NPIV dependencies during fabric-switch replacement. The risk it addresses is: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. This check is tied to the technical principle: In FC end-host mode, UCS FI behaves as an NPV gateway with upstream NPIV-capable fabric switches, not as a fabric-merging FC core. The immediate correction remains: Select supported FC mode and connect each fabric to suitable NPIV-capable upstream switches with correct VSAN connectivity. Periodically validate the safeguard through two different observations. Inspect FI FC mode and upstream switch NPIV state Verify vHBA virtual N-port login through the intended upstream fabric. The continuing acceptance target is: Each vHBA logs into the correct isolated SAN fabric and receives authorized storage zoning.
Incorrect Answers
A:This is a continuing control for dual-fabric fibre channel san paths; its underlying principle is: SAN multipath resiliency relies on independent initiator paths, FI fabrics, switches and target portals, not merely on two WWPNs. The recurring risk here is different: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The appropriate ongoing control must prevent recurrence of that particular failure, not just the separate issue of: A UCS database server has two virtual HBAs but both paths terminate on fabric A and lose all storage when it goes down. The intended long-term acceptance condition remains: Each vHBA logs into the correct isolated SAN fabric and receives authorized storage zoning.
B:This is a continuing control for fcoe no-drop priority isolation; its underlying principle is: FCoE storage transport needs coherent supported Data Center Bridging QoS, commonly including PFC for assigned storage traffic classes. The recurring risk here is different: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The appropriate ongoing control must prevent recurrence of that particular failure, not just the separate issue of: An Ethernet network combines FCoE SAN traffic with lossy application bursts but does not reserve appropriate lossless treatment. The intended long-term acceptance condition remains: Each vHBA logs into the correct isolated SAN fabric and receives authorized storage zoning.
D:This is a continuing control for fc uplink throughput for storage; its underlying principle is: vHBA virtual link rates do not create physical FC capacity; SAN fabric uplink bandwidth and oversubscription must be budgeted. The recurring risk here is different: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. The appropriate ongoing control must prevent recurrence of that particular failure, not just the separate issue of: A UCS fabric adds many high-speed vHBAs but uses only one slow FC uplink and experiences queueing at peak backup time. The intended long-term acceptance condition remains: Each vHBA logs into the correct isolated SAN fabric and receives authorized storage zoning.
Question 296
At a modular X-Series compute design, a proposed deployment has this failure mode: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The maintenance plan must not disrupt unrelated tenants. Which design correction most directly addresses this specific failure or requirement?
- Correct the approved FCoE VLAN-to-VSAN association and preserve tenant SAN isolation.
- Budget capacity and queueing under one-fabric failure using expected peak storage demand.
- Allocate one supported vHBA per fabric and validate operating-system MPIO and SAN zoning end to end.
- Select supported FC mode and connect each fabric to suitable NPIV-capable upstream switches with correct VSAN connectivity.
Explanation
Correct Answer
A:The relevant failure is: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The technical distinction is: FCoE uses an appropriate Ethernet transport and VLAN mapping while FC zoning and fabric membership remain VSAN scoped. The targeted correction is: Correct the approved FCoE VLAN-to-VSAN association and preserve tenant SAN isolation. Before changing the design, check two independent observations. Inspect FCoE VLAN and VSAN bindings at FI and upstream switch Verify fabric login and target discovery on the correct VSAN. Accept the change only if: Host initiators discover only approved targets through the intended SAN domain.
Incorrect Answers
B:This action targets storage path failover with asymmetric bandwidth, where the mechanism is: Availability paths also require degraded-mode performance planning; two physically diverse links alone do not guarantee equal capacity. That is a separate condition from the problem in this question: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. Even a successful repair of the alternative would not establish the required result: Host initiators discover only approved targets through the intended SAN domain. The applicable design change must address the diagnosed mechanism of the stated case, not the neighboring design problem.
C:This action targets dual-fabric fibre channel san paths, where the mechanism is: SAN multipath resiliency relies on independent initiator paths, FI fabrics, switches and target portals, not merely on two WWPNs. That is a separate condition from the problem in this question: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. Even a successful repair of the alternative would not establish the required result: Host initiators discover only approved targets through the intended SAN domain. The applicable design change must address the diagnosed mechanism of the stated case, not the neighboring design problem.
D:This action targets fc end-host npv uplink identity, where the mechanism is: In FC end-host mode, UCS FI behaves as an NPV gateway with upstream NPIV-capable fabric switches, not as a fabric-merging FC core. That is a separate condition from the problem in this question: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. Even a successful repair of the alternative would not establish the required result: Host initiators discover only approved targets through the intended SAN domain. The applicable design change must address the diagnosed mechanism of the stated case, not the neighboring design problem.
Question 297
At a mission-critical UCS blade installation, the cause remains unconfirmed for this reported issue: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. Acceptance requires evidence from the running system, not just the saved design. Which pair of observations most directly tests the proposed diagnosis before a change?
- Inspect per-fabric FC port rate and oversubscription; measure application latency with one path intentionally removed.
- Inspect FI FC mode and upstream switch NPIV state; verify vHBA virtual N-port login through the intended upstream fabric.
- Inspect FCoE priority/CoS at FI and switch; correlate PFC or drop counters with storage path resets under stress.
- Inspect FCoE VLAN and VSAN bindings at FI and upstream switch; verify fabric login and target discovery on the correct VSAN.
Explanation
Correct Answer
D:The first observation is: Inspect FCoE VLAN and VSAN bindings at FI and upstream switch The independent second observation is: Verify fabric login and target discovery on the correct VSAN. Together they test the proposed diagnosis of this incident: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The underlying technical principle is: FCoE uses an appropriate Ethernet transport and VLAN mapping while FC zoning and fabric membership remain VSAN scoped. If those checks confirm it, the appropriate next action is: Correct the approved FCoE VLAN-to-VSAN association and preserve tenant SAN isolation. The expected measurable result is: Host initiators discover only approved targets through the intended SAN domain.
Incorrect Answers
A:These observations investigate storage path failover with asymmetric bandwidth; they would be useful if the symptoms were: Two SAN fabrics exist but one has much less bandwidth, so losing the primary fabric creates unacceptable I/O latency. That alternative rests on the principle: Availability paths also require degraded-mode performance planning; two physically diverse links alone do not guarantee equal capacity. The question instead asks for evidence about: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The discriminating observations here are: Inspect FCoE VLAN and VSAN bindings at FI and upstream switch Verify fabric login and target discovery on the correct VSAN.
B:These observations investigate fc end-host npv uplink identity; they would be useful if the symptoms were: An FI operates Fibre Channel end-host/NPV mode, yet a design expects it to merge two upstream fabrics as a standalone FC switch. That alternative rests on the principle: In FC end-host mode, UCS FI behaves as an NPV gateway with upstream NPIV-capable fabric switches, not as a fabric-merging FC core. The question instead asks for evidence about: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The discriminating observations here are: Inspect FCoE VLAN and VSAN bindings at FI and upstream switch Verify fabric login and target discovery on the correct VSAN.
C:These observations investigate fcoe no-drop priority isolation; they would be useful if the symptoms were: An Ethernet network combines FCoE SAN traffic with lossy application bursts but does not reserve appropriate lossless treatment. That alternative rests on the principle: FCoE storage transport needs coherent supported Data Center Bridging QoS, commonly including PFC for assigned storage traffic classes. The question instead asks for evidence about: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The discriminating observations here are: Inspect FCoE VLAN and VSAN bindings at FI and upstream switch Verify fabric login and target discovery on the correct VSAN.
Question 298
At an Intersight-managed UCS cluster, a failure review must identify the central technical cause of: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. One component outage must remain inside the agreed availability budget. Which engineering principle best explains the observed behavior?
- Direct-attached FC storage and FCoE port roles are platform/release dependent and must be verified against specific Cisco FI and array compatibility.
- Availability paths also require degraded-mode performance planning; two physically diverse links alone do not guarantee equal capacity.
- vHBA virtual link rates do not create physical FC capacity; SAN fabric uplink bandwidth and oversubscription must be budgeted.
- FCoE uses an appropriate Ethernet transport and VLAN mapping while FC zoning and fabric membership remain VSAN scoped.
Explanation
Correct Answer
D:The controlling technical principle is: FCoE uses an appropriate Ethernet transport and VLAN mapping while FC zoning and fabric membership remain VSAN scoped. This matters because the reported design failure is: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The first diagnostic check is: Inspect FCoE VLAN and VSAN bindings at FI and upstream switch The independent check is: Verify fabric login and target discovery on the correct VSAN. These facts support the targeted intervention: Correct the approved FCoE VLAN-to-VSAN association and preserve tenant SAN isolation. Confirm that the resulting design meets this condition: Host initiators discover only approved targets through the intended SAN domain.
Incorrect Answers
A:The offered principle describes direct-attached fc storage support boundaries: Direct-attached FC storage and FCoE port roles are platform/release dependent and must be verified against specific Cisco FI and array compatibility. That is useful for a distinct incident, such as: A design assumes every UCS FI and storage array combination supports direct FC target attachment in the same way as an external SAN switch. It does not account for the reported failure: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The governing principle in this situation is: FCoE uses an appropriate Ethernet transport and VLAN mapping while FC zoning and fabric membership remain VSAN scoped.
B:The offered principle describes storage path failover with asymmetric bandwidth: Availability paths also require degraded-mode performance planning; two physically diverse links alone do not guarantee equal capacity. That is useful for a distinct incident, such as: Two SAN fabrics exist but one has much less bandwidth, so losing the primary fabric creates unacceptable I/O latency. It does not account for the reported failure: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The governing principle in this situation is: FCoE uses an appropriate Ethernet transport and VLAN mapping while FC zoning and fabric membership remain VSAN scoped.
C:The offered principle describes fc uplink throughput for storage: vHBA virtual link rates do not create physical FC capacity; SAN fabric uplink bandwidth and oversubscription must be budgeted. That is useful for a distinct incident, such as: A UCS fabric adds many high-speed vHBAs but uses only one slow FC uplink and experiences queueing at peak backup time. It does not account for the reported failure: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The governing principle in this situation is: FCoE uses an appropriate Ethernet transport and VLAN mapping while FC zoning and fabric membership remain VSAN scoped.
Question 299
At a dual-fabric virtualization host estate, the service owner needs evidence of resolution for: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The architect must preserve the intended failure domains. Which measured result most directly proves the original requirement is satisfied?
- Storage meets performance and availability objectives in normal and degraded modes.
- Host initiators discover only approved targets through the intended SAN domain.
- Storage remains accessible through the surviving SAN fabric without an unsupported failover mechanism.
- Storage traffic avoids preventable frame loss without pausing unrelated IP services globally.
Explanation
Correct Answer
B:The relevant measurable success criterion is: Host initiators discover only approved targets through the intended SAN domain. It addresses the original reported defect: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. A saved design or configuration command alone does not establish that outcome. Observe the affected system in two independent ways: Inspect FCoE VLAN and VSAN bindings at FI and upstream switch Verify fabric login and target discovery on the correct VSAN. The correction being evaluated is: Correct the approved FCoE VLAN-to-VSAN association and preserve tenant SAN isolation. The underlying reason that correction matters is: FCoE uses an appropriate Ethernet transport and VLAN mapping while FC zoning and fabric membership remain VSAN scoped.
Incorrect Answers
A:This metric would help validate a correction to fc uplink throughput for storage, rather than the original reported issue. The other issue is: A UCS fabric adds many high-speed vHBAs but uses only one slow FC uplink and experiences queueing at peak backup time. Here the defect to be resolved is: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The expected measurable outcome for the actual incident is: Host initiators discover only approved targets through the intended SAN domain. A positive result for the other service would not prove this requirement is met.
C:This metric would help validate a correction to dual-fabric fibre channel san paths, rather than the original reported issue. The other issue is: A UCS database server has two virtual HBAs but both paths terminate on fabric A and lose all storage when it goes down. Here the defect to be resolved is: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The expected measurable outcome for the actual incident is: Host initiators discover only approved targets through the intended SAN domain. A positive result for the other service would not prove this requirement is met.
D:This metric would help validate a correction to fcoe no-drop priority isolation, rather than the original reported issue. The other issue is: An Ethernet network combines FCoE SAN traffic with lossy application bursts but does not reserve appropriate lossless treatment. Here the defect to be resolved is: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The expected measurable outcome for the actual incident is: Host initiators discover only approved targets through the intended SAN domain. A positive result for the other service would not prove this requirement is met.
Question 300
At a Cisco UCS domain expansion, after correction, the team wants to prevent recurrence of: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The team needs a defensible design decision rather than a vendor feature checklist. Which continuing design control best prevents the same problem from recurring?
- Validate FCoE mapping whenever converged network VLAN allocation changes.
- Retest interoperability after FI firmware or storage array upgrades.
- Review backup-fabric capacity before adding demanding workloads.
- Audit DCB maps whenever FI uplink trunk policies change.
Explanation
Correct Answer
A:The most relevant ongoing safeguard is: Validate FCoE mapping whenever converged network VLAN allocation changes. The risk it addresses is: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. This check is tied to the technical principle: FCoE uses an appropriate Ethernet transport and VLAN mapping while FC zoning and fabric membership remain VSAN scoped. The immediate correction remains: Correct the approved FCoE VLAN-to-VSAN association and preserve tenant SAN isolation. Periodically validate the safeguard through two different observations. Inspect FCoE VLAN and VSAN bindings at FI and upstream switch Verify fabric login and target discovery on the correct VSAN. The continuing acceptance target is: Host initiators discover only approved targets through the intended SAN domain.
Incorrect Answers
B:This is a continuing control for direct-attached fc storage support boundaries; its underlying principle is: Direct-attached FC storage and FCoE port roles are platform/release dependent and must be verified against specific Cisco FI and array compatibility. The recurring risk here is different: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The appropriate ongoing control must prevent recurrence of that particular failure, not just the separate issue of: A design assumes every UCS FI and storage array combination supports direct FC target attachment in the same way as an external SAN switch. The intended long-term acceptance condition remains: Host initiators discover only approved targets through the intended SAN domain.
C:This is a continuing control for storage path failover with asymmetric bandwidth; its underlying principle is: Availability paths also require degraded-mode performance planning; two physically diverse links alone do not guarantee equal capacity. The recurring risk here is different: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The appropriate ongoing control must prevent recurrence of that particular failure, not just the separate issue of: Two SAN fabrics exist but one has much less bandwidth, so losing the primary fabric creates unacceptable I/O latency. The intended long-term acceptance condition remains: Host initiators discover only approved targets through the intended SAN domain.
D:This is a continuing control for fcoe no-drop priority isolation; its underlying principle is: FCoE storage transport needs coherent supported Data Center Bridging QoS, commonly including PFC for assigned storage traffic classes. The recurring risk here is different: A UCS vHBA uses FCoE traffic on an Ethernet uplink but the upstream switch maps it to the wrong VSAN. The appropriate ongoing control must prevent recurrence of that particular failure, not just the separate issue of: An Ethernet network combines FCoE SAN traffic with lossy application bursts but does not reserve appropriate lossless treatment. The intended long-term acceptance condition remains: Host initiators discover only approved targets through the intended SAN domain.