Cisco 300-420 Practice Test 3
Question 20
A regional office plans IPv6 addresses for wired wireless and infrastructure networks without repeatedly renumbering. The observed fault is: Assigning one identical subnet to multiple separated campus links can create address conflicts and broken reachability. Which recovery is BEST once this fault is identified?
- The controlled recovery is to reallocate unique /64 segments and validate gateway advertisements and aggregation.
- The controlled recovery is to use an IPv4 classful mask to divide the IPv6 /48 into LANs.
- The controlled recovery is to create the same /64 across every routed distribution segment.
- The controlled recovery is to randomly allocate prefixes without a documented aggregation scheme.
Explanation
Correct Answer
A:Consistent /64 LAN subnetting supports standard IPv6 host addressing while route summarization benefits from site hierarchy. Relevant evidence includes IPv6 delegated block, /64 subnet plan, routing advertisements, neighbor discovery and growth inventory.
Incorrect Answers
B:Use an IPv4 classful mask to divide the IPv6 /48 into LANs. Assigning one identical subnet to multiple separated campus links can create address conflicts and broken reachability. Use the controlled remediation: reallocate unique /64 segments and validate gateway advertisements and aggregation.
C:Create the same /64 across every routed distribution segment. Assigning one identical subnet to multiple separated campus links can create address conflicts and broken reachability. Use the controlled remediation: reallocate unique /64 segments and validate gateway advertisements and aggregation.
D:Randomly allocate prefixes without a documented aggregation scheme. Assigning one identical subnet to multiple separated campus links can create address conflicts and broken reachability. Use the controlled remediation: reallocate unique /64 segments and validate gateway advertisements and aggregation.
Question 21
A multisite network needs to keep detailed area topology from being flooded across the entire core. Which enterprise design procedure best meets this requirement?
- Make several disconnected Level-2 backbones and assume local adjacencies connect them automatically.
- Design IS-IS Level-1 areas attached through suitable Level-1-2 routers to a contiguous Level-2 backbone.
- Place every access router into a single global topology without a scale assessment.
- Use an Ethernet VLAN ID as the IS-IS area boundary instead of router-level design.
Explanation
Correct Answer
B:Confirm the result using level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability. IS-IS Level-1 confines local topology while Level-2 provides interarea routing through a connected backbone.
Incorrect Answers
A:Building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. This change targets the wrong mechanism for IS-IS Level-1 Level-2 hierarchy design.
C:Place every access router into a single global topology without a scale assessment. IS-IS Level-1 confines local topology while Level-2 provides interarea routing through a connected backbone. Instead inspect level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
D:Building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. Use an Ethernet VLAN ID as the IS-IS area boundary instead of router-level design.
Question 22
A multisite network needs to keep detailed area topology from being flooded across the entire core. Which evidence best distinguishes the intended state from a superficial indicator?
- Level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
- A marketing claim without measured routing, capacity or failure-domain evidence.
- An old network diagram with no current route, policy, or redundancy state.
- A feature-license screenshot without the required design or acceptance tests.
Explanation
Correct Answer
A:The intended procedure is design IS-IS Level-1 areas attached through suitable Level-1-2 routers to a contiguous Level-2 backbone. IS-IS Level-1 confines local topology while Level-2 provides interarea routing through a connected backbone.
Incorrect Answers
B:This observation alone cannot establish iS-IS Level-1 Level-2 hierarchy design. IS-IS Level-1 confines local topology while Level-2 provides interarea routing through a connected backbone.
C:This observation alone cannot establish iS-IS Level-1 Level-2 hierarchy design. The decisive evidence instead includes level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
D:This observation alone cannot establish iS-IS Level-1 Level-2 hierarchy design. A feature-license screenshot without the required design or acceptance tests.
Question 23
A multisite network needs to keep detailed area topology from being flooded across the entire core. Which underlying principle explains the correct decision?
- A longer IP prefix is always less specific than the default route.
- IS-IS Level-1 confines local topology while Level-2 provides interarea routing through a connected backbone.
- Cloud connectivity automatically removes any requirement for routing or policy.
- Any single device automatically guarantees high availability for every site.
Explanation
Correct Answer
B:This is why the appropriate action is design IS-IS Level-1 areas attached through suitable Level-1-2 routers to a contiguous Level-2 backbone. Confirm it with level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
Incorrect Answers
A:A longer IP prefix is always less specific than the default route. This is an incorrect generalization for iS-IS Level-1 Level-2 hierarchy design. The relevant rule is iS-IS Level-1 confines local topology while Level-2 provides interarea routing through a connected backbone. Verify using level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
C:Cloud connectivity automatically removes any requirement for routing or policy. This is an incorrect generalization for iS-IS Level-1 Level-2 hierarchy design. The relevant rule is iS-IS Level-1 confines local topology while Level-2 provides interarea routing through a connected backbone. Verify using level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
D:Any single device automatically guarantees high availability for every site. This is an incorrect generalization for iS-IS Level-1 Level-2 hierarchy design. The relevant rule is iS-IS Level-1 confines local topology while Level-2 provides interarea routing through a connected backbone. Verify using level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
Question 24
A multisite network needs to keep detailed area topology from being flooded across the entire core. Suppose the operator instead makes this incorrect change: Make several disconnected Level-2 backbones and assume local adjacencies connect them automatically. What is the most material consequence of that mistake?
- A healthy unrelated system proves the intended failure domain is protected.
- The failure is entirely cosmetic because all control-plane changes are harmless.
- Building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies.
- Collecting telemetry originally caused the missing route or service outage.
Explanation
Correct Answer
C:The right response is design IS-IS Level-1 areas attached through suitable Level-1-2 routers to a contiguous Level-2 backbone. This explains why the proposed shortcut does not solve iS-IS Level-1 Level-2 hierarchy design.
Incorrect Answers
A:A healthy unrelated system proves the intended failure domain is protected. The actual failure is building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. Check level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
B:The failure is entirely cosmetic because all control-plane changes are harmless. The actual failure is building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. Check level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
D:Collecting telemetry originally caused the missing route or service outage. The actual failure is building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. Check level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
Question 25
A multisite network needs to keep detailed area topology from being flooded across the entire core. The observed fault is: Building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. Which controlled remediation should be used?
- Repair the backbone or area border placement and validate interarea prefixes end to end.
- Place every access router into a single global topology without a scale assessment.
- Use an Ethernet VLAN ID as the IS-IS area boundary instead of router-level design.
- Make several disconnected Level-2 backbones and assume local adjacencies connect them automatically.
Explanation
Correct Answer
A:Relevant evidence includes level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability. IS-IS Level-1 confines local topology while Level-2 provides interarea routing through a connected backbone.
Incorrect Answers
B:Place every access router into a single global topology without a scale assessment. Building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. Use the controlled remediation: repair the backbone or area border placement and validate interarea prefixes end to end.
C:Use an Ethernet VLAN ID as the IS-IS area boundary instead of router-level design. Building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. Use the controlled remediation: repair the backbone or area border placement and validate interarea prefixes end to end.
D:Make several disconnected Level-2 backbones and assume local adjacencies connect them automatically. Building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. Use the controlled remediation: repair the backbone or area border placement and validate interarea prefixes end to end.
Question 26
A service provider style enterprise uses one IS-IS backbone and several access areas with different scaling needs. What is the most defensible configuration decision?
- For this enterprise design, the architect should design IS-IS Level-1 areas attached through suitable Level-1-2 routers to a contiguous Level-2 backbone.
- For this enterprise design, the architect should place every access router into a single global topology without a scale assessment.
- For this enterprise design, the architect should use an Ethernet VLAN ID as the IS-IS area boundary instead of router-level design.
- For this enterprise design, the architect should make several disconnected Level-2 backbones and assume local adjacencies connect them automatically.
Explanation
Correct Answer
A:Confirm the result using level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability. This is the specific corrective action for IS-IS Level-1 Level-2 hierarchy design.
Incorrect Answers
B:Place every access router into a single global topology without a scale assessment. IS-IS Level-1 confines local topology while Level-2 provides interarea routing through a connected backbone. Instead inspect level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
C:Building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. In this case, a service provider style enterprise uses one IS-IS backbone and several access areas with different scaling needs.
D:Building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. The relevant action is design IS-IS Level-1 areas attached through suitable Level-1-2 routers to a contiguous Level-2 backbone.
Question 27
A service provider style enterprise uses one IS-IS backbone and several access areas with different scaling needs. Which evidence BEST confirms the actual technical behavior?
- Inspect the following evidence: level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
- Inspect the following evidence: one successful ping to an unrelated test host without a path or failover test.
- Inspect the following evidence: a marketing claim without measured routing, capacity or failure-domain evidence.
- Inspect the following evidence: an old network diagram with no current route, policy, or redundancy state.
Explanation
Correct Answer
A:The intended procedure is design IS-IS Level-1 areas attached through suitable Level-1-2 routers to a contiguous Level-2 backbone. This evidence observes the actual iS-IS Level-1 Level-2 hierarchy design mechanism and its result.
Incorrect Answers
B:This observation alone cannot establish iS-IS Level-1 Level-2 hierarchy design. One successful ping to an unrelated test host without a path or failover test.
C:This observation alone cannot establish iS-IS Level-1 Level-2 hierarchy design. A marketing claim without measured routing, capacity or failure-domain evidence.
D:This observation alone cannot establish iS-IS Level-1 Level-2 hierarchy design. In this case, a service provider style enterprise uses one IS-IS backbone and several access areas with different scaling needs.
Question 28
A service provider style enterprise uses one IS-IS backbone and several access areas with different scaling needs. What networking or enterprise network design concept best explains this scenario?
- The relevant principle is that any single device automatically guarantees high availability for every site.
- The relevant principle is that a longer IP prefix is always less specific than the default route.
- The relevant principle is that an operational up state alone proves every security and design objective is met.
- The relevant principle is that iS-IS Level-1 confines local topology while Level-2 provides interarea routing through a connected backbone.
Explanation
Correct Answer
D:This is why the appropriate action is design IS-IS Level-1 areas attached through suitable Level-1-2 routers to a contiguous Level-2 backbone.
Incorrect Answers
A:Any single device automatically guarantees high availability for every site. This is an incorrect generalization for iS-IS Level-1 Level-2 hierarchy design. The relevant rule is iS-IS Level-1 confines local topology while Level-2 provides interarea routing through a connected backbone. Verify using level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
B:A longer IP prefix is always less specific than the default route. This is an incorrect generalization for iS-IS Level-1 Level-2 hierarchy design. The relevant rule is iS-IS Level-1 confines local topology while Level-2 provides interarea routing through a connected backbone. Verify using level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
C:An operational up state alone proves every security and design objective is met. This is an incorrect generalization for iS-IS Level-1 Level-2 hierarchy design. The relevant rule is iS-IS Level-1 confines local topology while Level-2 provides interarea routing through a connected backbone. Verify using level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
Question 29
A service provider style enterprise uses one IS-IS backbone and several access areas with different scaling needs. Suppose the operator instead makes this incorrect change: Make several disconnected Level-2 backbones and assume local adjacencies connect them automatically. Which resulting fault should the reviewer identify?
- The resulting technical fault is that building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies.
- The resulting technical fault is that collecting telemetry originally caused the missing route or service outage.
- The resulting technical fault is that a correct change-control review makes all WAN carriers fail simultaneously.
- The resulting technical fault is that the failure is entirely cosmetic because all control-plane changes are harmless.
Explanation
Correct Answer
A:The right response is design IS-IS Level-1 areas attached through suitable Level-1-2 routers to a contiguous Level-2 backbone. IS-IS Level-1 confines local topology while Level-2 provides interarea routing through a connected backbone.
Incorrect Answers
B:Collecting telemetry originally caused the missing route or service outage. The actual failure is building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. Check level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
C:A correct change-control review makes all WAN carriers fail simultaneously. The actual failure is building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. Check level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
D:The failure is entirely cosmetic because all control-plane changes are harmless. The actual failure is building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. Check level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability.
Question 30
A service provider style enterprise uses one IS-IS backbone and several access areas with different scaling needs. The observed fault is: Building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. How should the issue be corrected and verified?
- The controlled recovery is to use an Ethernet VLAN ID as the IS-IS area boundary instead of router-level design.
- The controlled recovery is to make several disconnected Level-2 backbones and assume local adjacencies connect them automatically.
- The controlled recovery is to repair the backbone or area border placement and validate interarea prefixes end to end.
- The controlled recovery is to place every access router into a single global topology without a scale assessment.
Explanation
Correct Answer
C:Relevant evidence includes level-1 and Level-2 adjacency tables, area IDs, LSP scope and interarea route reachability. This corrects the described failure and provides a verifiable outcome.
Incorrect Answers
A:Use an Ethernet VLAN ID as the IS-IS area boundary instead of router-level design. Building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. Use the controlled remediation: repair the backbone or area border placement and validate interarea prefixes end to end.
B:Make several disconnected Level-2 backbones and assume local adjacencies connect them automatically. Building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. Use the controlled remediation: repair the backbone or area border placement and validate interarea prefixes end to end.
D:Place every access router into a single global topology without a scale assessment. Building isolated Level-2 islands can prevent intended interarea connectivity despite healthy local adjacencies. Use the controlled remediation: repair the backbone or area border placement and validate interarea prefixes end to end.