Pure Storage FlashArray Implementation Specialist Practice Test 34
Question 330
An enterprise change review is deciding whether its response to fibre channel target-port cabling has been justified. The fictional case facts are: A hospital SAN reports a target WWPN on the opposite fabric from the approved port map. The review needs three separate components: a sound FlashArray administration principle, a scoped authorized response, and an independent measurable success check. Choose EXACTLY THREE statements that fulfill those roles.
- Rack installation should use the rail set and orientation approved for the shipped chassis.
- Resolve documented prerequisite mismatches before assigning array fleet roles.
- Hosts see expected target identities through each designated FC fabric.
- The customer can authenticate with intended roles, while temporary installer credentials are no longer active.
- SAN host paths must be cabled to intended FC ports and distinct fabrics according to the approved topology.
- Correct FC patching and zoning dependencies without changing unrelated production initiators.
Explanation
Correct Answer
C:Hosts see expected target identities through each designated FC fabric. This shows whether the scoped response worked: Correct FC patching and zoning dependencies without changing unrelated production initiators. A hospital SAN reports a target WWPN on the opposite fabric from the approved port map. The result should be supported by this evidence: Trace target port WWPNs through physical switch ports and current fabric maps.
E:SAN host paths must be cabled to intended FC ports and distinct fabrics according to the approved topology. A hospital SAN reports a target WWPN on the opposite fabric from the approved port map. The comparison to make is: Trace target port WWPNs through physical switch ports and current fabric maps. That principle leads to a bounded response: Correct FC patching and zoning dependencies without changing unrelated production initiators.
F:A hospital SAN reports a target WWPN on the opposite fabric from the approved port map. Correct FC patching and zoning dependencies without changing unrelated production initiators. Verify the change by checking: Hosts see expected target identities through each designated FC fabric. The action implements this principle: SAN host paths must be cabled to intended FC ports and distinct fabrics according to the approved topology.
Incorrect Answers
A:Rack installation should use the rail set and orientation approved for the shipped chassis. That is a separate rail kit selection and orientation concern; it does not explain the case: A hospital SAN reports a target WWPN on the opposite fabric from the approved port map. The governing distinction here is: SAN host paths must be cabled to intended FC ports and distinct fabrics according to the approved topology. The governing rule must instead lead to: Correct FC patching and zoning dependencies without changing unrelated production initiators.
B:Resolve documented prerequisite mismatches before assigning array fleet roles. That change targets a separate pure fusion fleet prerequisites concern; the unresolved issue is: A hospital SAN reports a target WWPN on the opposite fabric from the approved port map. The scoped response is: Correct FC patching and zoning dependencies without changing unrelated production initiators. The action should implement: SAN host paths must be cabled to intended FC ports and distinct fabrics according to the approved topology.
D:The customer can authenticate with intended roles, while temporary installer credentials are no longer active. That outcome tests a separate privileged local account handoff concern, not whether the reported problem is fixed: A hospital SAN reports a target WWPN on the opposite fabric from the approved port map. A directly relevant result would be: Hosts see expected target identities through each designated FC fabric. The acceptance test needs evidence from: Trace target port WWPNs through physical switch ports and current fabric maps.
Question 331
A hypothetical FlashArray operations change concerns storage ethernet target-port role mapping in the Installation area. The change or incident record reports: A new array's storage VLAN was patched to a port reserved for management access. Before modifying any FlashArray object, the administrator must identify the defensible operating principle. Which ONE governing principle directly applies? Choose ONE answer.
- Physical chassis, shelf and cable labeling should unambiguously match asset, service and support records.
- Array initialization must use the signed management network values with correct subnet and gateway consistency.
- Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
- A visually neat cable installation is insufficient without a command-backed topology and health check.
Explanation
Correct Answer
C:Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role. A new array's storage VLAN was patched to a port reserved for management access. The comparison to make is: Inspect current model port map, configured service role and actual switch connections.
Incorrect Answers
A:Physical chassis, shelf and cable labeling should unambiguously match asset, service and support records. That is a separate rack labels and asset identification concern; it does not explain the case: A new array's storage VLAN was patched to a port reserved for management access. The governing distinction here is: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
B:Array initialization must use the signed management network values with correct subnet and gateway consistency. That is a separate ip initialization and subnet masks concern; it does not explain the case: A new array's storage VLAN was patched to a port reserved for management access. The governing distinction here is: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
D:A visually neat cable installation is insufficient without a command-backed topology and health check. That is a separate post-cabling controller and shelf link verification concern; it does not explain the case: A new array's storage VLAN was patched to a port reserved for management access. The governing distinction here is: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
Question 332
During FlashArray administration concerning storage ethernet target-port role mapping, an operator reviews this fictional service issue: A new array's storage VLAN was patched to a port reserved for management access. Several explanations remain plausible until the relevant configuration and runtime evidence are checked. Which ONE specific evidence package should the administrator examine before deciding the change or diagnosis? Choose ONE answer.
- Inspect management port labels, switch destinations and the approved dual-controller cabling diagram.
- Verify supported serial-console interface, expected connection settings and physical access authorization.
- Inspect current model port map, configured service role and actual switch connections.
- Compare live port-link state, controller connectivity and shelf paths with the approved as-built drawing.
Explanation
Correct Answer
C:A new array's storage VLAN was patched to a port reserved for management access. Inspect current model port map, configured service role and actual switch connections. These observations test the rule: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
Incorrect Answers
A:Inspect management port labels, switch destinations and the approved dual-controller cabling diagram. Those checks address a separate dual-controller management cabling concern, not the specific finding: A new array's storage VLAN was patched to a port reserved for management access. The useful observations are: Inspect current model port map, configured service role and actual switch connections.
B:Verify supported serial-console interface, expected connection settings and physical access authorization. Those checks address a separate controller initialization through approved console concern, not the specific finding: A new array's storage VLAN was patched to a port reserved for management access. The useful observations are: Inspect current model port map, configured service role and actual switch connections.
D:Compare live port-link state, controller connectivity and shelf paths with the approved as-built drawing. Those checks address a separate post-cabling controller and shelf link verification concern, not the specific finding: A new array's storage VLAN was patched to a port reserved for management access. The useful observations are: Inspect current model port map, configured service role and actual switch connections.
Question 333
A change manager requests a safe and limited FlashArray response to a Installation problem involving storage ethernet target-port role mapping. The reported situation is: A new array's storage VLAN was patched to a port reserved for management access. The change must follow the observed facts, preserve recovery capability and avoid unrelated service impact. Which ONE bounded administrative action best matches this case? Choose ONE answer.
- Complete the approved registration workflow or document the supported restricted-site exception.
- Reroute and secure cabling with supported lengths and defined service clearance.
- Correct the exact management network settings after network-owner confirmation.
- Move incorrect patching to approved target interfaces and retest with the network owner.
Explanation
Correct Answer
D:A new array's storage VLAN was patched to a port reserved for management access. Move incorrect patching to approved target interfaces and retest with the network owner. Verify the change by checking: Expected initiator-to-target reachability works only on the authorized storage segments.
Incorrect Answers
A:Complete the approved registration workflow or document the supported restricted-site exception. That change targets a separate pure1 registration and telemetry authorization concern; the unresolved issue is: A new array's storage VLAN was patched to a port reserved for management access. The scoped response is: Move incorrect patching to approved target interfaces and retest with the network owner.
B:Reroute and secure cabling with supported lengths and defined service clearance. That change targets a separate cable strain relief and service loops concern; the unresolved issue is: A new array's storage VLAN was patched to a port reserved for management access. The scoped response is: Move incorrect patching to approved target interfaces and retest with the network owner.
C:Correct the exact management network settings after network-owner confirmation. That change targets a separate ip initialization and subnet masks concern; the unresolved issue is: A new array's storage VLAN was patched to a port reserved for management access. The scoped response is: Move incorrect patching to approved target interfaces and retest with the network owner.
Question 334
Two independent FlashArray administrator reviewers discuss storage ethernet target-port role mapping. Their case record says: A new array's storage VLAN was patched to a port reserved for management access. One requires diagnostic evidence that can distinguish the actual issue from lookalike symptoms; the other requires a limited and approved remediation. Choose EXACTLY TWO statements that jointly provide those roles.
- Apply approved DNS/NTP settings and recheck dependent services.
- Verify supported serial-console interface, expected connection settings and physical access authorization.
- Check safe-lift plan, component weights, rack mounting instructions and the available lifting device.
- Inspect current model port map, configured service role and actual switch connections.
- Move incorrect patching to approved target interfaces and retest with the network owner.
Explanation
Correct Answer
D:A new array's storage VLAN was patched to a port reserved for management access. Inspect current model port map, configured service role and actual switch connections. These observations test the rule: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role. The evidence supports this limited action: Move incorrect patching to approved target interfaces and retest with the network owner.
E:A new array's storage VLAN was patched to a port reserved for management access. Move incorrect patching to approved target interfaces and retest with the network owner. Verify the change by checking: Expected initiator-to-target reachability works only on the authorized storage segments. The change should follow this observation: Inspect current model port map, configured service role and actual switch connections.
Incorrect Answers
A:Apply approved DNS/NTP settings and recheck dependent services. That change targets a separate time configuration at first startup concern; the unresolved issue is: A new array's storage VLAN was patched to a port reserved for management access. The scoped response is: Move incorrect patching to approved target interfaces and retest with the network owner. The authorized change must instead follow: Inspect current model port map, configured service role and actual switch connections.
B:Verify supported serial-console interface, expected connection settings and physical access authorization. Those checks address a separate controller initialization through approved console concern, not the specific finding: A new array's storage VLAN was patched to a port reserved for management access. The useful observations are: Inspect current model port map, configured service role and actual switch connections. The relevant observation must instead support: Move incorrect patching to approved target interfaces and retest with the network owner.
C:Check safe-lift plan, component weights, rack mounting instructions and the available lifting device. Those checks address a separate load-assisted chassis mounting concern, not the specific finding: A new array's storage VLAN was patched to a port reserved for management access. The useful observations are: Inspect current model port map, configured service role and actual switch connections. The relevant observation must instead support: Move incorrect patching to approved target interfaces and retest with the network owner.
Question 335
An enterprise change review is deciding whether its response to storage ethernet target-port role mapping has been justified. The fictional case facts are: A new array's storage VLAN was patched to a port reserved for management access. The review needs three separate components: a sound FlashArray administration principle, a scoped authorized response, and an independent measurable success check. Choose EXACTLY THREE statements that fulfill those roles.
- Resolve any identified seating, cabling or power fault before declaring chassis commissioning complete.
- The array boots into a supported specified release and health checks show no new faults.
- Expected initiator-to-target reachability works only on the authorized storage segments.
- Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
- Volumes should be presented only to approved host identities or host groups with reviewed sharing semantics.
- Move incorrect patching to approved target interfaces and retest with the network owner.
Explanation
Correct Answer
C:Expected initiator-to-target reachability works only on the authorized storage segments. This shows whether the scoped response worked: Move incorrect patching to approved target interfaces and retest with the network owner. A new array's storage VLAN was patched to a port reserved for management access. The result should be supported by this evidence: Inspect current model port map, configured service role and actual switch connections.
D:Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role. A new array's storage VLAN was patched to a port reserved for management access. The comparison to make is: Inspect current model port map, configured service role and actual switch connections. That principle leads to a bounded response: Move incorrect patching to approved target interfaces and retest with the network owner.
F:A new array's storage VLAN was patched to a port reserved for management access. Move incorrect patching to approved target interfaces and retest with the network owner. Verify the change by checking: Expected initiator-to-target reachability works only on the authorized storage segments. The action implements this principle: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
Incorrect Answers
A:Resolve any identified seating, cabling or power fault before declaring chassis commissioning complete. That change targets a separate initial controller and enclosure status lights concern; the unresolved issue is: A new array's storage VLAN was patched to a port reserved for management access. The scoped response is: Move incorrect patching to approved target interfaces and retest with the network owner. The action should implement: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
B:The array boots into a supported specified release and health checks show no new faults. That outcome tests a separate purity software staging on newly installed hardware concern, not whether the reported problem is fixed: A new array's storage VLAN was patched to a port reserved for management access. A directly relevant result would be: Expected initiator-to-target reachability works only on the authorized storage segments. The acceptance test needs evidence from: Inspect current model port map, configured service role and actual switch connections.
E:Volumes should be presented only to approved host identities or host groups with reviewed sharing semantics. That is a separate host and host-group mapping safety concern; it does not explain the case: A new array's storage VLAN was patched to a port reserved for management access. The governing distinction here is: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role. The governing rule must instead lead to: Move incorrect patching to approved target interfaces and retest with the network owner.
Question 336
A hypothetical FlashArray operations change concerns storage ethernet target-port role mapping in the Installation area. The change or incident record reports: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. Before modifying any FlashArray object, the administrator must identify the defensible operating principle. Which ONE governing principle directly applies? Choose ONE answer.
- Physical Ethernet links require transceivers and cabling supported by both selected ports and the switch fabric.
- SAN host paths must be cabled to intended FC ports and distinct fabrics according to the approved topology.
- A physical link should be verified for supported speed, optics and error health after cabling.
- Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
Explanation
Correct Answer
D:Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role. An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The comparison to make is: Inspect current model port map, configured service role and actual switch connections.
Incorrect Answers
A:Physical Ethernet links require transceivers and cabling supported by both selected ports and the switch fabric. That is a separate ethernet optics matching concern; it does not explain the case: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The governing distinction here is: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
B:SAN host paths must be cabled to intended FC ports and distinct fabrics according to the approved topology. That is a separate fibre channel target-port cabling concern; it does not explain the case: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The governing distinction here is: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
C:A physical link should be verified for supported speed, optics and error health after cabling. That is a separate switch port speed and error validation concern; it does not explain the case: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The governing distinction here is: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
Question 337
During FlashArray administration concerning storage ethernet target-port role mapping, an operator reviews this fictional service issue: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. Several explanations remain plausible until the relevant configuration and runtime evidence are checked. Which ONE specific evidence package should the administrator examine before deciding the change or diagnosis? Choose ONE answer.
- Check safe-lift plan, component weights, rack mounting instructions and the available lifting device.
- Inspect current model port map, configured service role and actual switch connections.
- Trace target port WWPNs through physical switch ports and current fabric maps.
- Read hardware labels, model-specific component map and matching supported procedure.
Explanation
Correct Answer
B:An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. Inspect current model port map, configured service role and actual switch connections. These observations test the rule: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
Incorrect Answers
A:Check safe-lift plan, component weights, rack mounting instructions and the available lifting device. Those checks address a separate load-assisted chassis mounting concern, not the specific finding: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The useful observations are: Inspect current model port map, configured service role and actual switch connections.
C:Trace target port WWPNs through physical switch ports and current fabric maps. Those checks address a separate fibre channel target-port cabling concern, not the specific finding: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The useful observations are: Inspect current model port map, configured service role and actual switch connections.
D:Read hardware labels, model-specific component map and matching supported procedure. Those checks address a separate chassis and controller hardware identity concern, not the specific finding: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The useful observations are: Inspect current model port map, configured service role and actual switch connections.
Question 338
A change manager requests a safe and limited FlashArray response to a Installation problem involving storage ethernet target-port role mapping. The reported situation is: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The change must follow the observed facts, preserve recovery capability and avoid unrelated service impact. Which ONE bounded administrative action best matches this case? Choose ONE answer.
- Fit the approved blanking pieces and restore the intended airflow path before production load.
- Correct the as-built labels before accepting the implementation.
- Move incorrect patching to approved target interfaces and retest with the network owner.
- Rotate or disable temporary credentials and establish least-privilege named ownership after initial setup.
Explanation
Correct Answer
C:An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. Move incorrect patching to approved target interfaces and retest with the network owner. Verify the change by checking: Expected initiator-to-target reachability works only on the authorized storage segments.
Incorrect Answers
A:Fit the approved blanking pieces and restore the intended airflow path before production load. That change targets a separate blanking and airflow integrity concern; the unresolved issue is: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The scoped response is: Move incorrect patching to approved target interfaces and retest with the network owner.
B:Correct the as-built labels before accepting the implementation. That change targets a separate rack labels and asset identification concern; the unresolved issue is: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The scoped response is: Move incorrect patching to approved target interfaces and retest with the network owner.
D:Rotate or disable temporary credentials and establish least-privilege named ownership after initial setup. That change targets a separate privileged local account handoff concern; the unresolved issue is: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The scoped response is: Move incorrect patching to approved target interfaces and retest with the network owner.
Question 339
Two independent FlashArray administrator reviewers discuss storage ethernet target-port role mapping. Their case record says: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. One requires diagnostic evidence that can distinguish the actual issue from lookalike symptoms; the other requires a limited and approved remediation. Choose EXACTLY TWO statements that jointly provide those roles.
- Trace target port WWPNs through physical switch ports and current fabric maps.
- Move incorrect patching to approved target interfaces and retest with the network owner.
- Inspect current model port map, configured service role and actual switch connections.
- Rebuild the shelf connection map using the supported sequence after a documented outage review.
- Read hardware labels, model-specific component map and matching supported procedure.
Explanation
Correct Answer
B:An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. Move incorrect patching to approved target interfaces and retest with the network owner. Verify the change by checking: Expected initiator-to-target reachability works only on the authorized storage segments. The change should follow this observation: Inspect current model port map, configured service role and actual switch connections.
C:An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. Inspect current model port map, configured service role and actual switch connections. These observations test the rule: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role. The evidence supports this limited action: Move incorrect patching to approved target interfaces and retest with the network owner.
Incorrect Answers
A:Trace target port WWPNs through physical switch ports and current fabric maps. Those checks address a separate fibre channel target-port cabling concern, not the specific finding: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The useful observations are: Inspect current model port map, configured service role and actual switch connections. The relevant observation must instead support: Move incorrect patching to approved target interfaces and retest with the network owner.
D:Rebuild the shelf connection map using the supported sequence after a documented outage review. That change targets a separate directflash shelf supported topology concern; the unresolved issue is: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The scoped response is: Move incorrect patching to approved target interfaces and retest with the network owner. The authorized change must instead follow: Inspect current model port map, configured service role and actual switch connections.
E:Read hardware labels, model-specific component map and matching supported procedure. Those checks address a separate chassis and controller hardware identity concern, not the specific finding: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The useful observations are: Inspect current model port map, configured service role and actual switch connections. The relevant observation must instead support: Move incorrect patching to approved target interfaces and retest with the network owner.
Question 340
An enterprise change review is deciding whether its response to storage ethernet target-port role mapping has been justified. The fictional case facts are: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The review needs three separate components: a sound FlashArray administration principle, a scoped authorized response, and an independent measurable success check. Choose EXACTLY THREE statements that fulfill those roles.
- Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
- Expected initiator-to-target reachability works only on the authorized storage segments.
- Stage and apply only the approved installation procedure with a documented rollback or support stop gate.
- The customer can authenticate with intended roles, while temporary installer credentials are no longer active.
- Commissioning must restrict privileged accounts to authorized implementation staff and establish customer-owned custody.
- Move incorrect patching to approved target interfaces and retest with the network owner.
Explanation
Correct Answer
A:Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role. An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The comparison to make is: Inspect current model port map, configured service role and actual switch connections. That principle leads to a bounded response: Move incorrect patching to approved target interfaces and retest with the network owner.
B:Expected initiator-to-target reachability works only on the authorized storage segments. This shows whether the scoped response worked: Move incorrect patching to approved target interfaces and retest with the network owner. An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The result should be supported by this evidence: Inspect current model port map, configured service role and actual switch connections.
F:An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. Move incorrect patching to approved target interfaces and retest with the network owner. Verify the change by checking: Expected initiator-to-target reachability works only on the authorized storage segments. The action implements this principle: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
Incorrect Answers
C:Stage and apply only the approved installation procedure with a documented rollback or support stop gate. That change targets a separate purity software staging on newly installed hardware concern; the unresolved issue is: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The scoped response is: Move incorrect patching to approved target interfaces and retest with the network owner. The action should implement: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role.
D:The customer can authenticate with intended roles, while temporary installer credentials are no longer active. That outcome tests a separate privileged local account handoff concern, not whether the reported problem is fixed: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. A directly relevant result would be: Expected initiator-to-target reachability works only on the authorized storage segments. The acceptance test needs evidence from: Inspect current model port map, configured service role and actual switch connections.
E:Commissioning must restrict privileged accounts to authorized implementation staff and establish customer-owned custody. That is a separate privileged local account handoff concern; it does not explain the case: An engineering cluster cannot discover its iSCSI targets because network cables follow an obsolete controller diagram. The governing distinction here is: Network cabling must distinguish iSCSI storage interfaces from management or replication ports by their supported role. The governing rule must instead lead to: Move incorrect patching to approved target interfaces and retest with the network owner.