cert
cert-1
cert-2

Pass Juniper JN0-664 Exam in First Attempt Guaranteed!

Get 100% Latest Exam Questions, Accurate & Verified Answers to Pass the Actual Exam!
30 Days Free Updates, Instant Download!

cert-5
cert-6
JN0-664 Exam - Verified By Experts
JN0-664 Premium File

JN0-664 Premium File

$69.99
$76.99
  • Premium File 96 Questions & Answers. Last Update: Nov 19, 2026

Whats Included:

  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
 
$76.99
$69.99
accept 20 downloads in the last 7 days
block-screenshots
Juniper JN0-664 Practice Test 49

Question 480

A Junos routing design reviewer evaluates an unsafe shortcut in this network customer scenario. A VPLS site stays reachable after PE maintenance, but the failover path has no documented service identifier or acceptance test, hiding a potential loop. Which assumption is MOST DIRECTLY dangerous or unsupported? Select ONE best answer.

  1. Enable dense-mode flooding across the entire sparse subscriber backbone solely to correct one missing video stream without evaluating blast radius.
  2. Assume an Established IPv4-unicast-only BGP session automatically distributes BGP Layer 2 VPN NLRI and labels to every PE.
  3. Configure one PE for BGP-signaled VPLS and another for unrelated LDP service discovery then assume VLAN IDs alone create a multipoint interconnect.
  4. Assign identical customer site IDs to unrelated participating VPLS sites and assume unique identification is unimportant because the PEs have different loopbacks.

Explanation

Correct Answer

D:

That conflicts with the edge-to-cloud principle: VPLS site identification and multihoming mechanisms help coordinate PE access, but customer-facing redundant paths need a supported convergence and loop-control design.

Incorrect Answers

A:

This alternative proposes: Enable dense-mode flooding across the entire sparse subscriber backbone solely to correct one missing video stream without evaluating blast radius. It concerns a different Junos engineering issue PIM dense mode versus sparse mode interface deployment, not the directly tested provider-network issue VPLS site identifiers multihoming and service convergence.

B:

This alternative proposes: Assume an Established IPv4-unicast-only BGP session automatically distributes BGP Layer 2 VPN NLRI and labels to every PE. It concerns a different Junos engineering issue BGP-signaled Layer 2 VPN NLRI and route target import, not the directly tested provider-network issue VPLS site identifiers multihoming and service convergence.

C:

This alternative proposes: Configure one PE for BGP-signaled VPLS and another for unrelated LDP service discovery then assume VLAN IDs alone create a multipoint interconnect. It concerns a different Junos engineering issue VPLS service control plane LDP versus BGP distribution, not the directly tested provider-network issue VPLS site identifiers multihoming and service convergence.

Question 481

A Junos service-provider routing engineer investigates the following routing and service incident: A customer's VM migrates to a new PE, but the old location remains advertised and traffic blackholes until EVPN route updates are examined. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.

  1. Validate EVPN multihoming Ethernet segment identifiers and designated-forwarder behavior before activating redundant customer links.
  2. Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding.
  3. Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail.
  4. Verify the transport and service label roles in an MPLS Layer 3 VPN before attributing a forwarding failure to the customer routing protocol.

Explanation

Correct Answer

B:

EVPN commonly conveys MAC reachability through BGP route type 2; optional IP binding and policies support host learning and next-hop selection, while label or encapsulation rules depend on the deployment. Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables.

Incorrect Answers

A:

This alternative proposes: Validate EVPN multihoming Ethernet segment identifiers and designated-forwarder behavior before activating redundant customer links. It concerns a different Junos engineering issue EVPN Ethernet segment multihoming and designated forwarder, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

C:

This alternative proposes: Verify service MTU and any supported pseudowire encapsulation/control-word expectations when a pseudowire is signaled Up but customer frames fail. It concerns a different Junos engineering issue Layer 2 pseudowire MTU and control-word interworking, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

D:

This alternative proposes: Verify the transport and service label roles in an MPLS Layer 3 VPN before attributing a forwarding failure to the customer routing protocol. It concerns a different Junos engineering issue MPLS VPN transport label stack and next hop, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

Question 482

A provider routing design review considers this situation. A customer's VM migrates to a new PE, but the old location remains advertised and traffic blackholes until EVPN route updates are examined. A colleague proposes: Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding. Which technical principle BEST supports that action? Select ONE best answer.

  1. On an OSPF broadcast network a DR and BDR reduce full-adjacency fanout; elections depend on eligible interface priorities and router IDs, and are not always preemptive.
  2. EVPN commonly conveys MAC reachability through BGP route type 2; optional IP binding and policies support host learning and next-hop selection, while label or encapsulation rules depend on the deployment.
  3. Multipoint Ethernet services learn source MAC locations and flood unknown unicast, broadcast and multicast within permitted service boundaries; split-horizon rules limit loop-causing PW-to-PW forwarding.
  4. EVPN all-active or single-active multihoming uses a shared ESI and appropriate DF/aliasing coordination to prevent BUM duplication and maintain reachable paths under failure.

Explanation

Correct Answer

B:

The relevant Junos service-provider networking principle is: EVPN commonly conveys MAC reachability through BGP route type 2; optional IP binding and policies support host learning and next-hop selection, while label or encapsulation rules depend on the deployment. In the described provider-network case (A customer's VM migrates to a new PE, but the old location remains advertised and traffic blackholes until EVPN route updates are examined.), it supports the planned action: Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding.

Incorrect Answers

A:

This alternative proposes: On an OSPF broadcast network a DR and BDR reduce full-adjacency fanout; elections depend on eligible interface priorities and router IDs, and are not always preemptive. It concerns a different Junos engineering issue OSPF designated router election on a multiaccess segment, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

C:

This alternative proposes: Multipoint Ethernet services learn source MAC locations and flood unknown unicast, broadcast and multicast within permitted service boundaries; split-horizon rules limit loop-causing PW-to-PW forwarding. It concerns a different Junos engineering issue VPLS MAC learning flooding and split-horizon safeguards, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

D:

This alternative proposes: EVPN all-active or single-active multihoming uses a shared ESI and appropriate DF/aliasing coordination to prevent BUM duplication and maintain reachable paths under failure. It concerns a different Junos engineering issue EVPN Ethernet segment multihoming and designated forwarder, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

Question 483

A Juniper service-provider engineer needs decisive verification evidence for this situation. A customer's VM migrates to a new PE, but the old location remains advertised and traffic blackholes until EVPN route updates are examined. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.

  1. Inspect show ospf3 neighbor, show ospf3 interface, IPv6 link-local addresses, area association, LSDB and inet6 routes independently of OSPFv2.
  2. Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables.
  3. Check service-site IDs, multihoming preference, attachment circuits, signaling reachability, MAC moves and measured forwarding during failover.
  4. Inspect show l2circuit connections, LDP session state, neighbor addresses, VC IDs, service-facing interfaces and transport LSP reachability.

Explanation

Correct Answer

B:

The direct discriminating observation is: Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables. In the stated situation (A customer's VM migrates to a new PE, but the old location remains advertised and traffic blackholes until EVPN route updates are examined.), the intended acceptance outcome is: A moved customer endpoint is reachable through its current PE and stale advertised paths are withdrawn or updated according to supported mobility behavior.

Incorrect Answers

A:

This alternative proposes: Inspect show ospf3 neighbor, show ospf3 interface, IPv6 link-local addresses, area association, LSDB and inet6 routes independently of OSPFv2. It concerns a different Junos engineering issue OSPFv3 IPv6 neighbor and IPv4 separation, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

C:

This alternative proposes: Check service-site IDs, multihoming preference, attachment circuits, signaling reachability, MAC moves and measured forwarding during failover. It concerns a different Junos engineering issue VPLS site identifiers multihoming and service convergence, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

D:

This alternative proposes: Inspect show l2circuit connections, LDP session state, neighbor addresses, VC IDs, service-facing interfaces and transport LSP reachability. It concerns a different Junos engineering issue LDP signaled Layer 2 circuit pseudowire status and VC identifiers, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

Question 484

A service-provider acceptance team reviews the result of a provider-service change. A customer's VM migrates to a new PE, but the old location remains advertised and traffic blackholes until EVPN route updates are examined. The intended verification is: Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables. Which outcome BEST demonstrates success? Select ONE best answer.

  1. The two attachment circuits join only their authorized sites and the pseudowire status and customer traffic counters remain stable.
  2. The authorized CE service survives a primary PE outage with the expected alternate active and without creating duplicated Ethernet forwarding.
  3. The correct VPN route is visible in the intended customer VRF with a valid forwarding next hop and is absent from unauthorized VRFs.
  4. A moved customer endpoint is reachable through its current PE and stale advertised paths are withdrawn or updated according to supported mobility behavior.

Explanation

Correct Answer

D:

The verified success outcome is: A moved customer endpoint is reachable through its current PE and stale advertised paths are withdrawn or updated according to supported mobility behavior. Confirm this by: Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables.

Incorrect Answers

A:

That option concerns LDP signaled Layer 2 circuit pseudowire status and VC identifiers. The related controlled intervention is: Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding.

B:

This alternative proposes: The authorized CE service survives a primary PE outage with the expected alternate active and without creating duplicated Ethernet forwarding. It concerns a different Junos engineering issue VPLS site identifiers multihoming and service convergence, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

C:

This alternative proposes: The correct VPN route is visible in the intended customer VRF with a valid forwarding next hop and is absent from unauthorized VRFs. It concerns a different Junos engineering issue VPNv4 bgp.l3vpn.0 versus customer VRF route tables, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning in the stated situation (A customer's VM migrates to a new PE, but the old location remains advertised and traffic blackholes until EVPN route updates are examined.). A better case-specific check is: Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables. The more targeted action is: Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding.

Question 485

A Junos service-provider routing engineer investigates this service-provider network scenario. A customer's VM migrates to a new PE, but the old location remains advertised and traffic blackholes until EVPN route updates are examined. Which TWO complementary steps combine a suitable technical action and its direct verification? Select TWO answers.

  1. Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs.
  2. Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables.
  3. Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding.
  4. Trace a VPNv4 prefix from MP-BGP reception to a customer VRF routing table, distinguishing provider VPN control-plane storage and installed customer forwarding routes.
  5. Classify subscriber traffic with an appropriate behavior-aggregate or multifield classifier and confirm forwarding-class assignments at ingress.

Explanation

Correct Answers

B:

The direct discriminating observation is: Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables.

C:

The case-specific routing and services action is: Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding. The governing Junos routing/service principle is: EVPN commonly conveys MAC reachability through BGP route type 2; optional IP binding and policies support host learning and next-hop selection, while label or encapsulation rules depend on the deployment.

Incorrect Answers

A:

This alternative proposes: Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs. It concerns a different Junos engineering issue Layer 2 pseudowire MTU and control-word interworking, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

D:

This alternative proposes: Trace a VPNv4 prefix from MP-BGP reception to a customer VRF routing table, distinguishing provider VPN control-plane storage and installed customer forwarding routes. It concerns a different Junos engineering issue VPNv4 bgp.l3vpn.0 versus customer VRF route tables, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning in the stated situation (A customer's VM migrates to a new PE, but the old location remains advertised and traffic blackholes until EVPN route updates are examined.). A better case-specific check is: Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables. The more targeted action is: Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding.

E:

This alternative proposes: Classify subscriber traffic with an appropriate behavior-aggregate or multifield classifier and confirm forwarding-class assignments at ingress. It concerns a different Junos engineering issue Junos CoS behavior aggregate versus multifield classifiers, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

Question 486

A Junos service-provider routing engineer investigates the following routing and service incident: Two tenants reuse an identical MAC value in isolated EVPN instances, and the operator needs to verify route-target and EVI context rather than collapse both domains. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.

  1. Use BGP route damping conservatively and verify whether instability penalties suppress otherwise available paths during a customer route-flap event.
  2. Choose a supported VPLS signaling model and verify peer discovery, service membership and MPLS forwarding transport independently.
  3. Validate EVPN multihoming Ethernet segment identifiers and designated-forwarder behavior before activating redundant customer links.
  4. Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding.

Explanation

Correct Answer

D:

The case-specific routing and services action is: Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding. The governing Junos routing/service principle is: EVPN commonly conveys MAC reachability through BGP route type 2; optional IP binding and policies support host learning and next-hop selection, while label or encapsulation rules depend on the deployment. Verify the decision through: Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables.

Incorrect Answers

A:

This alternative proposes: Use BGP route damping conservatively and verify whether instability penalties suppress otherwise available paths during a customer route-flap event. It concerns a different Junos engineering issue BGP flap damping penalties and recovery, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

B:

This alternative proposes: Choose a supported VPLS signaling model and verify peer discovery, service membership and MPLS forwarding transport independently. It concerns a different Junos engineering issue VPLS service control plane LDP versus BGP distribution, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

C:

This alternative proposes: Validate EVPN multihoming Ethernet segment identifiers and designated-forwarder behavior before activating redundant customer links. It concerns a different Junos engineering issue EVPN Ethernet segment multihoming and designated forwarder, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

Question 487

A provider routing design review considers this situation. Two tenants reuse an identical MAC value in isolated EVPN instances, and the operator needs to verify route-target and EVI context rather than collapse both domains. A colleague proposes: Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding. Which technical principle BEST supports that action? Select ONE best answer.

  1. A BGP-signaled Layer 2 VPN advertises service-related NLRI and label reachability; route-target and instance-policy behavior determine which remote service participates.
  2. EVPN commonly conveys MAC reachability through BGP route type 2; optional IP binding and policies support host learning and next-hop selection, while label or encapsulation rules depend on the deployment.
  3. Multipoint Ethernet services learn source MAC locations and flood unknown unicast, broadcast and multicast within permitted service boundaries; split-horizon rules limit loop-causing PW-to-PW forwarding.
  4. OSPF backbone area 0 carries interarea reachability; a virtual link can join a disconnected backbone through an eligible transit area, but it is not a substitute for planned topology repair.

Explanation

Correct Answer

B:

The relevant Junos service-provider networking principle is: EVPN commonly conveys MAC reachability through BGP route type 2; optional IP binding and policies support host learning and next-hop selection, while label or encapsulation rules depend on the deployment. In the described provider-network case (Two tenants reuse an identical MAC value in isolated EVPN instances, and the operator needs to verify route-target and EVI context rather than collapse both domains.), it supports the planned action: Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding.

Incorrect Answers

A:

This alternative proposes: A BGP-signaled Layer 2 VPN advertises service-related NLRI and label reachability; route-target and instance-policy behavior determine which remote service participates. It concerns a different Junos engineering issue BGP-signaled Layer 2 VPN NLRI and route target import, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

C:

This alternative proposes: Multipoint Ethernet services learn source MAC locations and flood unknown unicast, broadcast and multicast within permitted service boundaries; split-horizon rules limit loop-causing PW-to-PW forwarding. It concerns a different Junos engineering issue VPLS MAC learning flooding and split-horizon safeguards, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

D:

This alternative proposes: OSPF backbone area 0 carries interarea reachability; a virtual link can join a disconnected backbone through an eligible transit area, but it is not a substitute for planned topology repair. It concerns a different Junos engineering issue OSPF multi-area backbone connectivity and virtual-link limitations, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

Question 488

A Juniper service-provider engineer needs decisive verification evidence for this situation. Two tenants reuse an identical MAC value in isolated EVPN instances, and the operator needs to verify route-target and EVI context rather than collapse both domains. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.

  1. Check area IDs, ABR relationships, backbone LSA visibility, virtual-link state, and show ospf neighbor and database before adjusting policies.
  2. Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs.
  3. Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables.
  4. Inspect Ethernet segment configuration, ESI values, DF election or relevant designated-forwarder state, ES routes, BGP reachability and measured failover forwarding.

Explanation

Correct Answer

C:

The direct discriminating observation is: Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables. In the stated situation (Two tenants reuse an identical MAC value in isolated EVPN instances, and the operator needs to verify route-target and EVI context rather than collapse both domains.), the intended acceptance outcome is: A moved customer endpoint is reachable through its current PE and stale advertised paths are withdrawn or updated according to supported mobility behavior.

Incorrect Answers

A:

This alternative proposes: Check area IDs, ABR relationships, backbone LSA visibility, virtual-link state, and show ospf neighbor and database before adjusting policies. It concerns a different Junos engineering issue OSPF multi-area backbone connectivity and virtual-link limitations, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

B:

This alternative proposes: Compare CE frame sizes, attachment-circuit encapsulation, pseudowire MTU, control-word configuration, interface drops and forwarding test results at both PEs. It concerns a different Junos engineering issue Layer 2 pseudowire MTU and control-word interworking, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

D:

This alternative proposes: Inspect Ethernet segment configuration, ESI values, DF election or relevant designated-forwarder state, ES routes, BGP reachability and measured failover forwarding. It concerns a different Junos engineering issue EVPN Ethernet segment multihoming and designated forwarder, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

Question 489

A service-provider acceptance team reviews the result of a provider-service change. Two tenants reuse an identical MAC value in isolated EVPN instances, and the operator needs to verify route-target and EVI context rather than collapse both domains. The intended verification is: Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables. Which outcome BEST demonstrates success? Select ONE best answer.

  1. A moved customer endpoint is reachable through its current PE and stale advertised paths are withdrawn or updated according to supported mobility behavior.
  2. Multicast subscribers continue receiving approved sources when one RP fails, with no duplicate or missing source registration state.
  3. The authorized CE service survives a primary PE outage with the expected alternate active and without creating duplicated Ethernet forwarding.
  4. The appropriate PEs establish only the requested customer Layer 2 connections and do not merge different customer switching domains.

Explanation

Correct Answer

A:

The verified success outcome is: A moved customer endpoint is reachable through its current PE and stale advertised paths are withdrawn or updated according to supported mobility behavior. Confirm this by: Inspect EVPN BGP family negotiation, MAC/IP advertisement, EVI/RT membership, remote PE next-hop reachability and learned MAC tables. The related controlled intervention is: Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding.

Incorrect Answers

B:

That option concerns Anycast RP resilient multicast service and routing policy. The related controlled intervention is: Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding.

C:

This alternative proposes: The authorized CE service survives a primary PE outage with the expected alternate active and without creating duplicated Ethernet forwarding. It concerns a different Junos engineering issue VPLS site identifiers multihoming and service convergence, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

D:

That option concerns BGP-signaled Layer 2 VPN NLRI and route target import. The related controlled intervention is: Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding.

Question 490

A Junos routing design reviewer evaluates an unsafe shortcut in this network customer scenario. Two tenants reuse an identical MAC value in isolated EVPN instances, and the operator needs to verify route-target and EVI context rather than collapse both domains. Which assumption is MOST DIRECTLY dangerous or unsupported? Select ONE best answer.

  1. Create two circuits with different VC identifiers and assume LDP can automatically infer they belong to the same customer service because the physical ports are Up.
  2. Assume every pair of routers on a broadcast VLAN must display Full adjacency, and bounce the elected DR whenever another router is only Two-Way.
  3. Assume an Established IPv4-unicast-only BGP session automatically distributes BGP Layer 2 VPN NLRI and labels to every PE.
  4. Assume every MAC learned on an EVPN remote PE must be discovered exclusively by data-plane flood without any BGP MAC/IP advertisement.

Explanation

Correct Answer

D:

Apply instead: Use BGP EVPN MAC/IP reachability information to explain how remote PE devices learn and advertise Ethernet endpoints without relying only on flooding.

Incorrect Answers

A:

This alternative proposes: Create two circuits with different VC identifiers and assume LDP can automatically infer they belong to the same customer service because the physical ports are Up. It concerns a different Junos engineering issue LDP signaled Layer 2 circuit pseudowire status and VC identifiers, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

B:

This alternative proposes: Assume every pair of routers on a broadcast VLAN must display Full adjacency, and bounce the elected DR whenever another router is only Two-Way. It concerns a different Junos engineering issue OSPF designated router election on a multiaccess segment, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

C:

This alternative proposes: Assume an Established IPv4-unicast-only BGP session automatically distributes BGP Layer 2 VPN NLRI and labels to every PE. It concerns a different Junos engineering issue BGP-signaled Layer 2 VPN NLRI and route target import, not the directly tested provider-network issue EVPN MAC IP route type two control plane and learning.

Service Provider Routing and Switching, Professional (JNCIP-SP) (JN0-664) Practice Tests