Juniper JN0-664 Practice Test 39
Question 380
A Junos service-provider routing engineer investigates this service-provider network scenario. A customer receives a default route from a shared Internet VRF but outbound traffic fails because return routes or NAT at the breakout hub are missing. Which TWO complementary steps combine a suitable technical action and its direct verification? Select TWO answers.
- Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.
- Investigate rejected or down IS-IS adjacencies by verifying circuit levels, IS-IS NET identifiers, authentication and interface MTU before changing the full IGP.
- Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings.
- Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries.
- Check CE neighbor health, routing-instance interface membership, customer prefixes in instance.inet.0, VRF export policy and remote import results.
Explanation
Correct Answers
A:The case-specific routing and services action is: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.
D:The direct discriminating observation is: Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries.
Incorrect Answers
B:This alternative proposes: Investigate rejected or down IS-IS adjacencies by verifying circuit levels, IS-IS NET identifiers, authentication and interface MTU before changing the full IGP. It concerns a different Junos engineering issue IS-IS adjacency NET and interface mismatch troubleshooting, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.
C:This alternative proposes: Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings. It concerns a different Junos engineering issue BGP-signaled Layer 2 VPN NLRI and route target import, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.
E:This alternative proposes: Check CE neighbor health, routing-instance interface membership, customer prefixes in instance.inet.0, VRF export policy and remote import results. It concerns a different Junos engineering issue PE to CE routing and customer route redistribution, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.
Question 381
A Junos service-provider routing engineer investigates the following routing and service incident: Two PEs both learn a customer's prefix from one multihomed CE and advertise it back to the same site without origin filtering. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.
- Validate the PE-to-CE routing protocol and routing-instance binding before exporting customer routes into MP-BGP or changing provider-core policies.
- Investigate an OSPF adjacency that remains in ExStart or Exchange by comparing interface MTU and protocol parameters before resetting every neighbor.
- Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
- Verify the transport and service label roles in an MPLS Layer 3 VPN before attributing a forwarding failure to the customer routing protocol.
Explanation
Correct Answer
C:The case-specific routing and services action is: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection. The governing Junos routing/service principle is: SoO identifies the originating customer site for policy-based loop prevention; OSPF sham links can influence customer OSPF path choice across the VPN backbone in particular backdoor-link designs.
Incorrect Answers
A:This alternative proposes: Validate the PE-to-CE routing protocol and routing-instance binding before exporting customer routes into MP-BGP or changing provider-core policies. It concerns a different Junos engineering issue PE to CE routing and customer route redistribution, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
B:This alternative proposes: Investigate an OSPF adjacency that remains in ExStart or Exchange by comparing interface MTU and protocol parameters before resetting every neighbor. It concerns a different Junos engineering issue OSPF adjacency MTU and hello compatibility diagnosis, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
D:This alternative proposes: Verify the transport and service label roles in an MPLS Layer 3 VPN before attributing a forwarding failure to the customer routing protocol. It concerns a different Junos engineering issue MPLS VPN transport label stack and next hop, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
Question 382
A provider routing design review considers this situation. Two PEs both learn a customer's prefix from one multihomed CE and advertise it back to the same site without origin filtering. A colleague proposes: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection. Which technical principle BEST supports that action? Select ONE best answer.
- PE/CE exchange can use a supported static, BGP, OSPF or other mechanism; the customer interface must belong to the intended VRF and outbound policy determines what enters VPN reachability.
- A BGP route can be accepted yet hidden or unusable when the advertised next hop cannot be resolved through an appropriate routing table or transport tunnel.
- SoO identifies the originating customer site for policy-based loop prevention; OSPF sham links can influence customer OSPF path choice across the VPN backbone in particular backdoor-link designs.
- IPv6 Layer 3 VPN routes use address-family-specific control-plane and forwarding information; a working IPv4 tenant VRF does not itself establish IPv6 connectivity.
Explanation
Correct Answer
C:The relevant Junos service-provider networking principle is: SoO identifies the originating customer site for policy-based loop prevention; OSPF sham links can influence customer OSPF path choice across the VPN backbone in particular backdoor-link designs. In the described provider-network case (Two PEs both learn a customer's prefix from one multihomed CE and advertise it back to the same site without origin filtering.), it supports the planned action: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
Incorrect Answers
A:This alternative proposes: PE/CE exchange can use a supported static, BGP, OSPF or other mechanism; the customer interface must belong to the intended VRF and outbound policy determines what enters VPN reachability. It concerns a different Junos engineering issue PE to CE routing and customer route redistribution, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
B:This alternative proposes: A BGP route can be accepted yet hidden or unusable when the advertised next hop cannot be resolved through an appropriate routing table or transport tunnel. It concerns a different Junos engineering issue BGP NEXT_HOP reachability and inet.3 recursion, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
D:This alternative proposes: IPv6 Layer 3 VPN routes use address-family-specific control-plane and forwarding information; a working IPv4 tenant VRF does not itself establish IPv6 connectivity. It concerns a different Junos engineering issue IPv6 Layer 3 VPN VPNv6 route families and forwarding, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
Question 383
A Juniper service-provider engineer needs decisive verification evidence for this situation. Two PEs both learn a customer's prefix from one multihomed CE and advertise it back to the same site without origin filtering. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.
- Check area IDs, ABR relationships, backbone LSA visibility, virtual-link state, and show ospf neighbor and database before adjusting policies.
- Check CE neighbor health, routing-instance interface membership, customer prefixes in instance.inet.0, VRF export policy and remote import results.
- Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries.
- Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy.
Explanation
Correct Answer
D:The direct discriminating observation is: Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy. In the stated situation (Two PEs both learn a customer's prefix from one multihomed CE and advertise it back to the same site without origin filtering.), the intended acceptance outcome is: The multihomed site avoids reaccepting its own redistributed routes, and intended OSPF traffic uses the validated primary or backup route.
Incorrect Answers
A:This alternative proposes: Check area IDs, ABR relationships, backbone LSA visibility, virtual-link state, and show ospf neighbor and database before adjusting policies. It concerns a different Junos engineering issue OSPF multi-area backbone connectivity and virtual-link limitations, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
B:This alternative proposes: Check CE neighbor health, routing-instance interface membership, customer prefixes in instance.inet.0, VRF export policy and remote import results. It concerns a different Junos engineering issue PE to CE routing and customer route redistribution, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
C:This alternative proposes: Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries. It concerns a different Junos engineering issue Layer 3 VPN hub spoke topology and controlled Internet breakout, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
Question 384
A service-provider acceptance team reviews the result of a provider-service change. Two PEs both learn a customer's prefix from one multihomed CE and advertise it back to the same site without origin filtering. The intended verification is: Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy. Which outcome BEST demonstrates success? Select ONE best answer.
- The customer transports frames within the agreed service MTU without unexplained fragmentation, truncation or interworking incompatibility.
- The multihomed site avoids reaccepting its own redistributed routes, and intended OSPF traffic uses the validated primary or backup route.
- Each site advertises and learns only authorized enterprise routes, without leaking internal core routes or other tenants' networks.
- Two customers may use the same internal subnet without conflated control-plane identities and only authorized VPNs import each others' prefixes.
Explanation
Correct Answer
B:The verified success outcome is: The multihomed site avoids reaccepting its own redistributed routes, and intended OSPF traffic uses the validated primary or backup route. Confirm this by: Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy.
Incorrect Answers
A:That option concerns Layer 2 pseudowire MTU and control-word interworking. The related controlled intervention is: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
C:That option concerns PE to CE routing and customer route redistribution. The related controlled intervention is: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
D:That option concerns Layer 3 VPN route distinguishers versus route targets. The related controlled intervention is: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
Question 385
A Junos routing design reviewer evaluates an unsafe shortcut in this network customer scenario. Two PEs both learn a customer's prefix from one multihomed CE and advertise it back to the same site without origin filtering. Which assumption is MOST DIRECTLY dangerous or unsupported? Select ONE best answer.
- Treat an RD as an access-control filter and set identical RDs for every unrelated VPN while leaving permissive RT import policy unrestricted.
- Treat a customer's multi-site VPN backdoor link as automatically equivalent to an OSPF intra-area backbone path and disable all route-loop safeguards.
- Import every FlowSpec announcement from any external neighbor with unrestricted discard actions and no authorization or validation.
- Assume a VPNv4 route with an advertised VPN label needs no LSP or other valid provider transport path to reach its egress PE.
Explanation
Correct Answer
B:That conflicts with the edge-to-cloud principle: SoO identifies the originating customer site for policy-based loop prevention; OSPF sham links can influence customer OSPF path choice across the VPN backbone in particular backdoor-link designs.
Incorrect Answers
A:This alternative proposes: Treat an RD as an access-control filter and set identical RDs for every unrelated VPN while leaving permissive RT import policy unrestricted. It concerns a different Junos engineering issue Layer 3 VPN route distinguishers versus route targets, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
C:This alternative proposes: Import every FlowSpec announcement from any external neighbor with unrestricted discard actions and no authorization or validation. It concerns a different Junos engineering issue BGP FlowSpec validation and filtering boundaries, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
D:This alternative proposes: Assume a VPNv4 route with an advertised VPN label needs no LSP or other valid provider transport path to reach its egress PE. It concerns a different Junos engineering issue MPLS VPN transport label stack and next hop, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
Question 386
A Junos service-provider routing engineer investigates the following routing and service incident: A customer OSPF network prefers a higher-cost interarea VPN route over a backdoor link and needs a design review of sham-link and metric conditions. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.
- Examine external route Type 1 versus Type 2 cost behavior and the forwarding cost toward the ASBR when determining why routers choose different exits.
- Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
- Select the supported inter-AS or carrier-of-carriers VPN interconnection model according to trust, labels, MP-BGP signaling and administrative boundary requirements.
- Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone.
Explanation
Correct Answer
B:The case-specific routing and services action is: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection. The governing Junos routing/service principle is: SoO identifies the originating customer site for policy-based loop prevention; OSPF sham links can influence customer OSPF path choice across the VPN backbone in particular backdoor-link designs. Verify the decision through: Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy.
Incorrect Answers
A:This alternative proposes: Examine external route Type 1 versus Type 2 cost behavior and the forwarding cost toward the ASBR when determining why routers choose different exits. It concerns a different Junos engineering issue OSPF external type E1 E2 route cost evaluation, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
C:This alternative proposes: Select the supported inter-AS or carrier-of-carriers VPN interconnection model according to trust, labels, MP-BGP signaling and administrative boundary requirements. It concerns a different Junos engineering issue Interprovider Layer 3 VPN options and carrier of carriers, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
D:This alternative proposes: Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone. It concerns a different Junos engineering issue Multicast VPN provider and customer traffic separation, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
Question 387
A provider routing design review considers this situation. A customer OSPF network prefers a higher-cost interarea VPN route over a backdoor link and needs a design review of sham-link and metric conditions. A colleague proposes: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection. Which technical principle BEST supports that action? Select ONE best answer.
- SoO identifies the originating customer site for policy-based loop prevention; OSPF sham links can influence customer OSPF path choice across the VPN backbone in particular backdoor-link designs.
- IPv6 Layer 3 VPN routes use address-family-specific control-plane and forwarding information; a working IPv4 tenant VRF does not itself establish IPv6 connectivity.
- A BGP route can be accepted yet hidden or unusable when the advertised next hop cannot be resolved through an appropriate routing table or transport tunnel.
- An RD distinguishes overlapping customer prefix routes in MP-BGP VPN NLRI, whereas RT extended communities guide import/export membership across VPN routing instances.
Explanation
Correct Answer
A:The relevant Junos service-provider networking principle is: SoO identifies the originating customer site for policy-based loop prevention; OSPF sham links can influence customer OSPF path choice across the VPN backbone in particular backdoor-link designs. In the described provider-network case (A customer OSPF network prefers a higher-cost interarea VPN route over a backdoor link and needs a design review of sham-link and metric conditions.), it supports the planned action: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
Incorrect Answers
B:This alternative proposes: IPv6 Layer 3 VPN routes use address-family-specific control-plane and forwarding information; a working IPv4 tenant VRF does not itself establish IPv6 connectivity. It concerns a different Junos engineering issue IPv6 Layer 3 VPN VPNv6 route families and forwarding, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
C:This alternative proposes: A BGP route can be accepted yet hidden or unusable when the advertised next hop cannot be resolved through an appropriate routing table or transport tunnel. It concerns a different Junos engineering issue BGP NEXT_HOP reachability and inet.3 recursion, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
D:This alternative proposes: An RD distinguishes overlapping customer prefix routes in MP-BGP VPN NLRI, whereas RT extended communities guide import/export membership across VPN routing instances. It concerns a different Junos engineering issue Layer 3 VPN route distinguishers versus route targets, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
Question 388
A Juniper service-provider engineer needs decisive verification evidence for this situation. A customer OSPF network prefers a higher-cost interarea VPN route over a backdoor link and needs a design review of sham-link and metric conditions. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.
- Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy.
- Review ASBR origin, advertised external metric type, internal path-to-ASBR cost, routing table preferences, and selected next hops at each PE.
- Check CE neighbor health, routing-instance interface membership, customer prefixes in instance.inet.0, VRF export policy and remote import results.
- Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population.
Explanation
Correct Answer
A:The direct discriminating observation is: Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy. In the stated situation (A customer OSPF network prefers a higher-cost interarea VPN route over a backdoor link and needs a design review of sham-link and metric conditions.), the intended acceptance outcome is: The multihomed site avoids reaccepting its own redistributed routes, and intended OSPF traffic uses the validated primary or backup route.
Incorrect Answers
B:This alternative proposes: Review ASBR origin, advertised external metric type, internal path-to-ASBR cost, routing table preferences, and selected next hops at each PE. It concerns a different Junos engineering issue OSPF external type E1 E2 route cost evaluation, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
C:This alternative proposes: Check CE neighbor health, routing-instance interface membership, customer prefixes in instance.inet.0, VRF export policy and remote import results. It concerns a different Junos engineering issue PE to CE routing and customer route redistribution, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
D:This alternative proposes: Compare PE routing-instance configuration, RD values, RT export/import communities, received VPN routes and per-instance inet.0 population. It concerns a different Junos engineering issue Layer 3 VPN route distinguishers versus route targets, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
Question 389
A service-provider acceptance team reviews the result of a provider-service change. A customer OSPF network prefers a higher-cost interarea VPN route over a backdoor link and needs a design review of sham-link and metric conditions. The intended verification is: Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy. Which outcome BEST demonstrates success? Select ONE best answer.
- The multihomed site avoids reaccepting its own redistributed routes, and intended OSPF traffic uses the validated primary or backup route.
- The correct VPN route is visible in the intended customer VRF with a valid forwarding next hop and is absent from unauthorized VRFs.
- Premium voice packets enter their intended forwarding class while unmarked best-effort traffic remains appropriately classified.
- Spokes exchange only approved traffic through the hub and optional shared Internet access follows inspected security and return-path controls.
Explanation
Correct Answer
A:The verified success outcome is: The multihomed site avoids reaccepting its own redistributed routes, and intended OSPF traffic uses the validated primary or backup route. Confirm this by: Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy. The related controlled intervention is: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
Incorrect Answers
B:This alternative proposes: The correct VPN route is visible in the intended customer VRF with a valid forwarding next hop and is absent from unauthorized VRFs. It concerns a different Junos engineering issue VPNv4 bgp.l3vpn.0 versus customer VRF route tables, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control in the stated situation (A customer OSPF network prefers a higher-cost interarea VPN route over a backdoor link and needs a design review of sham-link and metric conditions.). A better case-specific check is: Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy. The more targeted action is: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
C:That option concerns Junos CoS behavior aggregate versus multifield classifiers. The related controlled intervention is: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
D:That option concerns Layer 3 VPN hub spoke topology and controlled Internet breakout. The related controlled intervention is: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
Question 390
A Junos service-provider routing engineer investigates this service-provider network scenario. A customer OSPF network prefers a higher-cost interarea VPN route over a backdoor link and needs a design review of sham-link and metric conditions. Which TWO complementary steps combine a suitable technical action and its direct verification? Select TWO answers.
- Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy.
- Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries.
- Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
- Use BGP communities as controlled signals for provider routing policies instead of confusing tagging with guaranteed remote traffic behavior.
- Design an eBGP multihop session with explicit remote loopback reachability and appropriate TTL/session transport settings when directly connected peering is not used.
Explanation
Correct Answers
A:The direct discriminating observation is: Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy.
C:The case-specific routing and services action is: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
Incorrect Answers
B:This alternative proposes: Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries. It concerns a different Junos engineering issue Layer 3 VPN hub spoke topology and controlled Internet breakout, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
D:This alternative proposes: Use BGP communities as controlled signals for provider routing policies instead of confusing tagging with guaranteed remote traffic behavior. It concerns a different Junos engineering issue BGP communities and selective transit routing policy, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.
E:This alternative proposes: Design an eBGP multihop session with explicit remote loopback reachability and appropriate TTL/session transport settings when directly connected peering is not used. It concerns a different Junos engineering issue BGP external multihop and loopback peer reachability, not the directly tested provider-network issue Site of Origin and OSPF sham-link loop control.