cert
cert-1
cert-2

Pass Juniper JN0-664 Exam in First Attempt Guaranteed!

Get 100% Latest Exam Questions, Accurate & Verified Answers to Pass the Actual Exam!
30 Days Free Updates, Instant Download!

cert-5
cert-6
JN0-664 Exam - Verified By Experts
JN0-664 Premium File

JN0-664 Premium File

$69.99
$76.99
  • Premium File 96 Questions & Answers. Last Update: Nov 19, 2026

Whats Included:

  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
 
$76.99
$69.99
accept 20 downloads in the last 7 days
block-screenshots
Juniper JN0-664 Practice Test 38

Question 370

A Junos routing design reviewer evaluates an unsafe shortcut in this network customer scenario. A network observer sees a transport label removed before the final PE and assumes the VPN service label must also be invalid despite normal label-stack behavior. Which assumption is MOST DIRECTLY dangerous or unsupported? Select ONE best answer.

  1. Assume a VPNv4 route with an advertised VPN label needs no LSP or other valid provider transport path to reach its egress PE.
  2. Add a customer access interface to the provider's global inet.0 table and expect its overlapping RFC1918 subnet to remain isolated from every other tenant.
  3. Assume every MAC learned on an EVPN remote PE must be discovered exclusively by data-plane flood without any BGP MAC/IP advertisement.
  4. Enable MP-BGP VPN unicast for a tenant and promise its source multicast group will automatically traverse provider PEs with no MVPN or multicast setup.

Explanation

Correct Answer

A:

Apply instead: Verify the transport and service label roles in an MPLS Layer 3 VPN before attributing a forwarding failure to the customer routing protocol.

Incorrect Answers

B:

This alternative proposes: Add a customer access interface to the provider's global inet.0 table and expect its overlapping RFC1918 subnet to remain isolated from every other tenant. It concerns a different Junos engineering issue PE to CE routing and customer route redistribution, not the directly tested provider-network issue MPLS VPN transport label stack and next hop.

C:

This alternative proposes: Assume every MAC learned on an EVPN remote PE must be discovered exclusively by data-plane flood without any BGP MAC/IP advertisement. It concerns a different Junos engineering issue EVPN MAC IP route type two control plane and learning, not the directly tested provider-network issue MPLS VPN transport label stack and next hop.

D:

This alternative proposes: Enable MP-BGP VPN unicast for a tenant and promise its source multicast group will automatically traverse provider PEs with no MVPN or multicast setup. It concerns a different Junos engineering issue Multicast VPN provider and customer traffic separation, not the directly tested provider-network issue MPLS VPN transport label stack and next hop.

Question 371

A Junos service-provider routing engineer investigates the following routing and service incident: A retailer's branch VPN spokes should reach central payment services but not one another, yet a common import RT creates unintended spoke-to-spoke routes. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.

  1. Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone.
  2. Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.
  3. Verify the transport and service label roles in an MPLS Layer 3 VPN before attributing a forwarding failure to the customer routing protocol.
  4. Use reverse-path forwarding checks to determine why an arriving multicast packet is accepted on one interface but discarded on another.

Explanation

Correct Answer

B:

VPN topology is shaped by which prefixes are imported/exported between sites, and a shared service or Internet breakout must be explicitly engineered rather than assumed by one RT value. Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries.

Incorrect Answers

A:

This alternative proposes: Validate multicast VPN control and data-plane dependencies before claiming a customer group's IP multicast stream should traverse an MPLS provider backbone. It concerns a different Junos engineering issue Multicast VPN provider and customer traffic separation, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

C:

This alternative proposes: Verify the transport and service label roles in an MPLS Layer 3 VPN before attributing a forwarding failure to the customer routing protocol. It concerns a different Junos engineering issue MPLS VPN transport label stack and next hop, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

D:

This alternative proposes: Use reverse-path forwarding checks to determine why an arriving multicast packet is accepted on one interface but discarded on another. It concerns a different Junos engineering issue Multicast RPF validation and source reachability, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

Question 372

A provider routing design review considers this situation. A retailer's branch VPN spokes should reach central payment services but not one another, yet a common import RT creates unintended spoke-to-spoke routes. A colleague proposes: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access. Which technical principle BEST supports that action? Select ONE best answer.

  1. In a typical BGP/MPLS L3VPN, an outer transport label carries traffic toward the egress PE and an inner VPN label selects the egress service context as supported by the implementation.
  2. PE/CE exchange can use a supported static, BGP, OSPF or other mechanism; the customer interface must belong to the intended VRF and outbound policy determines what enters VPN reachability.
  3. Junos schedulers assign queue service treatment, but weights, strict priority and buffer settings must be balanced against starvation and hardware limitations.
  4. VPN topology is shaped by which prefixes are imported/exported between sites, and a shared service or Internet breakout must be explicitly engineered rather than assumed by one RT value.

Explanation

Correct Answer

D:

The relevant Junos service-provider networking principle is: VPN topology is shaped by which prefixes are imported/exported between sites, and a shared service or Internet breakout must be explicitly engineered rather than assumed by one RT value. In the described provider-network case (A retailer's branch VPN spokes should reach central payment services but not one another, yet a common import RT creates unintended spoke-to-spoke routes.), it supports the planned action: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.

Incorrect Answers

A:

This alternative proposes: In a typical BGP/MPLS L3VPN, an outer transport label carries traffic toward the egress PE and an inner VPN label selects the egress service context as supported by the implementation. It concerns a different Junos engineering issue MPLS VPN transport label stack and next hop, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

B:

This alternative proposes: PE/CE exchange can use a supported static, BGP, OSPF or other mechanism; the customer interface must belong to the intended VRF and outbound policy determines what enters VPN reachability. It concerns a different Junos engineering issue PE to CE routing and customer route redistribution, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

C:

This alternative proposes: Junos schedulers assign queue service treatment, but weights, strict priority and buffer settings must be balanced against starvation and hardware limitations. It concerns a different Junos engineering issue CoS schedulers scheduler-maps and bandwidth sharing, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

Question 373

A Juniper service-provider engineer needs decisive verification evidence for this situation. A retailer's branch VPN spokes should reach central payment services but not one another, yet a common import RT creates unintended spoke-to-spoke routes. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.

  1. Check CE neighbor health, routing-instance interface membership, customer prefixes in instance.inet.0, VRF export policy and remote import results.
  2. Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries.
  3. Inspect MAC tables per VPLS instance, flood counters, PE attachment circuits, pseudowire membership, MAC aging and loop-protection state.
  4. Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy.

Explanation

Correct Answer

B:

The direct discriminating observation is: Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries. In the stated situation (A retailer's branch VPN spokes should reach central payment services but not one another, yet a common import RT creates unintended spoke-to-spoke routes.), the intended acceptance outcome is: Spokes exchange only approved traffic through the hub and optional shared Internet access follows inspected security and return-path controls.

Incorrect Answers

A:

This alternative proposes: Check CE neighbor health, routing-instance interface membership, customer prefixes in instance.inet.0, VRF export policy and remote import results. It concerns a different Junos engineering issue PE to CE routing and customer route redistribution, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

C:

This alternative proposes: Inspect MAC tables per VPLS instance, flood counters, PE attachment circuits, pseudowire membership, MAC aging and loop-protection state. It concerns a different Junos engineering issue VPLS MAC learning flooding and split-horizon safeguards, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

D:

This alternative proposes: Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy. It concerns a different Junos engineering issue Site of Origin and OSPF sham-link loop control, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

Question 374

A service-provider acceptance team reviews the result of a provider-service change. A retailer's branch VPN spokes should reach central payment services but not one another, yet a common import RT creates unintended spoke-to-spoke routes. The intended verification is: Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries. Which outcome BEST demonstrates success? Select ONE best answer.

  1. Each site advertises and learns only authorized enterprise routes, without leaking internal core routes or other tenants' networks.
  2. Spokes exchange only approved traffic through the hub and optional shared Internet access follows inspected security and return-path controls.
  3. The chosen exit aligns to the operator's end-to-end cost policy, and failover to another valid ASBR meets the documented path objective.
  4. The intended remote VPN site can reach its authorized peer across the AS boundary without transferring unrelated tenants' routes or losing required label resolution.

Explanation

Correct Answer

B:

The verified success outcome is: Spokes exchange only approved traffic through the hub and optional shared Internet access follows inspected security and return-path controls. Confirm this by: Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries.

Incorrect Answers

A:

That option concerns PE to CE routing and customer route redistribution. The related controlled intervention is: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.

C:

That option concerns OSPF external type E1 E2 route cost evaluation. The related controlled intervention is: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.

D:

That option concerns Interprovider Layer 3 VPN options and carrier of carriers. The related controlled intervention is: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.

Question 375

A Junos service-provider routing engineer investigates this service-provider network scenario. A retailer's branch VPN spokes should reach central payment services but not one another, yet a common import RT creates unintended spoke-to-spoke routes. Which TWO complementary steps combine a suitable technical action and its direct verification? Select TWO answers.

  1. Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.
  2. Investigate rejected or down IS-IS adjacencies by verifying circuit levels, IS-IS NET identifiers, authentication and interface MTU before changing the full IGP.
  3. Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries.
  4. Configure a scheduler map for the intended egress forwarding classes and verify bandwidth, buffer and priority behavior during real congestion.
  5. Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding.

Explanation

Correct Answers

A:

The case-specific routing and services action is: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access. The governing Junos routing/service principle is: VPN topology is shaped by which prefixes are imported/exported between sites, and a shared service or Internet breakout must be explicitly engineered rather than assumed by one RT value.

C:

The direct discriminating observation is: Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries.

Incorrect Answers

B:

This alternative proposes: Investigate rejected or down IS-IS adjacencies by verifying circuit levels, IS-IS NET identifiers, authentication and interface MTU before changing the full IGP. It concerns a different Junos engineering issue IS-IS adjacency NET and interface mismatch troubleshooting, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

D:

This alternative proposes: Configure a scheduler map for the intended egress forwarding classes and verify bandwidth, buffer and priority behavior during real congestion. It concerns a different Junos engineering issue CoS schedulers scheduler-maps and bandwidth sharing, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

E:

This alternative proposes: Inspect customer IGMP/PIM membership, MVPN route state, provider tunnel or data-plane transport, RP/SSM mode, RPF and egress PE forwarding. It concerns a different Junos engineering issue Multicast VPN provider and customer traffic separation, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

Question 376

A Junos service-provider routing engineer investigates the following routing and service incident: A customer receives a default route from a shared Internet VRF but outbound traffic fails because return routes or NAT at the breakout hub are missing. What is the MOST appropriate FIRST action based on the facts given? Select ONE best answer.

  1. Verify IPv6 customer prefixes across a supported L3VPN by checking VPNv6 MP-BGP family, route targets and IPv6 customer forwarding independently of IPv4 VPNv4 behavior.
  2. Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.
  3. Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection.
  4. Examine external route Type 1 versus Type 2 cost behavior and the forwarding cost toward the ASBR when determining why routers choose different exits.

Explanation

Correct Answer

B:

The case-specific routing and services action is: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access. The governing Junos routing/service principle is: VPN topology is shaped by which prefixes are imported/exported between sites, and a shared service or Internet breakout must be explicitly engineered rather than assumed by one RT value. Verify the decision through: Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries.

Incorrect Answers

A:

This alternative proposes: Verify IPv6 customer prefixes across a supported L3VPN by checking VPNv6 MP-BGP family, route targets and IPv6 customer forwarding independently of IPv4 VPNv4 behavior. It concerns a different Junos engineering issue IPv6 Layer 3 VPN VPNv6 route families and forwarding, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

C:

This alternative proposes: Use Site of Origin controls and supported OSPF sham-link design where required to prevent multihomed customer loops or preserve intended intra-area OSPF path selection. It concerns a different Junos engineering issue Site of Origin and OSPF sham-link loop control, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

D:

This alternative proposes: Examine external route Type 1 versus Type 2 cost behavior and the forwarding cost toward the ASBR when determining why routers choose different exits. It concerns a different Junos engineering issue OSPF external type E1 E2 route cost evaluation, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

Question 377

A provider routing design review considers this situation. A customer receives a default route from a shared Internet VRF but outbound traffic fails because return routes or NAT at the breakout hub are missing. A colleague proposes: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access. Which technical principle BEST supports that action? Select ONE best answer.

  1. VPN topology is shaped by which prefixes are imported/exported between sites, and a shared service or Internet breakout must be explicitly engineered rather than assumed by one RT value.
  2. In a typical BGP/MPLS L3VPN, an outer transport label carries traffic toward the egress PE and an inner VPN label selects the egress service context as supported by the implementation.
  3. PE/CE exchange can use a supported static, BGP, OSPF or other mechanism; the customer interface must belong to the intended VRF and outbound policy determines what enters VPN reachability.
  4. BGP FlowSpec conveys traffic match and action rules through BGP signaling, but their enforcement, validation, supported match fields and authorization must be controlled.

Explanation

Correct Answer

A:

The relevant Junos service-provider networking principle is: VPN topology is shaped by which prefixes are imported/exported between sites, and a shared service or Internet breakout must be explicitly engineered rather than assumed by one RT value. In the described provider-network case (A customer receives a default route from a shared Internet VRF but outbound traffic fails because return routes or NAT at the breakout hub are missing.), it supports the planned action: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.

Incorrect Answers

B:

This alternative proposes: In a typical BGP/MPLS L3VPN, an outer transport label carries traffic toward the egress PE and an inner VPN label selects the egress service context as supported by the implementation. It concerns a different Junos engineering issue MPLS VPN transport label stack and next hop, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

C:

This alternative proposes: PE/CE exchange can use a supported static, BGP, OSPF or other mechanism; the customer interface must belong to the intended VRF and outbound policy determines what enters VPN reachability. It concerns a different Junos engineering issue PE to CE routing and customer route redistribution, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

D:

This alternative proposes: BGP FlowSpec conveys traffic match and action rules through BGP signaling, but their enforcement, validation, supported match fields and authorization must be controlled. It concerns a different Junos engineering issue BGP FlowSpec validation and filtering boundaries, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

Question 378

A Juniper service-provider engineer needs decisive verification evidence for this situation. A customer receives a default route from a shared Internet VRF but outbound traffic fails because return routes or NAT at the breakout hub are missing. Which observation MOST DIRECTLY distinguishes the relevant issue? Select ONE best answer.

  1. Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy.
  2. Inspect SSM group range, IGMPv3 (S,G) membership, source unicast route, RPF state, PIM joins and actual packet counts.
  3. Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries.
  4. Inspect BGP negotiated family, VPNv6 table, instance.inet6.0, RT import, IPv6 CE routing, next-hop transport and IPv6 forwarding counters.

Explanation

Correct Answer

C:

The direct discriminating observation is: Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries. In the stated situation (A customer receives a default route from a shared Internet VRF but outbound traffic fails because return routes or NAT at the breakout hub are missing.), the intended acceptance outcome is: Spokes exchange only approved traffic through the hub and optional shared Internet access follows inspected security and return-path controls.

Incorrect Answers

A:

This alternative proposes: Review CE dual-homing advertisements, SoO community tags, OSPF route type/cost, sham-link endpoint reachability and import/export policy. It concerns a different Junos engineering issue Site of Origin and OSPF sham-link loop control, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

B:

This alternative proposes: Inspect SSM group range, IGMPv3 (S,G) membership, source unicast route, RPF state, PIM joins and actual packet counts. It concerns a different Junos engineering issue Source-specific multicast and IGMPv3 source filtering, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

D:

This alternative proposes: Inspect BGP negotiated family, VPNv6 table, instance.inet6.0, RT import, IPv6 CE routing, next-hop transport and IPv6 forwarding counters. It concerns a different Junos engineering issue IPv6 Layer 3 VPN VPNv6 route families and forwarding, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

Question 379

A service-provider acceptance team reviews the result of a provider-service change. A customer receives a default route from a shared Internet VRF but outbound traffic fails because return routes or NAT at the breakout hub are missing. The intended verification is: Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries. Which outcome BEST demonstrates success? Select ONE best answer.

  1. Authorized IPv6 subnets communicate across customer sites while overlapping IPv4 tenant routing remains isolated and unchanged.
  2. Core route volume decreases while every authorized covered access subnet remains reachable and unintended prefixes stay filtered.
  3. Spokes exchange only approved traffic through the hub and optional shared Internet access follows inspected security and return-path controls.
  4. The ingress PE pushes an appropriate label stack and the egress PE forwards the packet in the authorized customer context without exposing traffic to another VPN.

Explanation

Correct Answer

C:

The verified success outcome is: Spokes exchange only approved traffic through the hub and optional shared Internet access follows inspected security and return-path controls. Confirm this by: Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries. The related controlled intervention is: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.

Incorrect Answers

A:

That option concerns IPv6 Layer 3 VPN VPNv6 route families and forwarding. The related controlled intervention is: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.

B:

That option concerns OSPF interarea route summarization and route restrictions. The related controlled intervention is: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.

D:

That option concerns MPLS VPN transport label stack and next hop. The related controlled intervention is: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.

Question 380

A Junos service-provider routing engineer investigates this service-provider network scenario. A customer receives a default route from a shared Internet VRF but outbound traffic fails because return routes or NAT at the breakout hub are missing. Which TWO complementary steps combine a suitable technical action and its direct verification? Select TWO answers.

  1. Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.
  2. Investigate rejected or down IS-IS adjacencies by verifying circuit levels, IS-IS NET identifiers, authentication and interface MTU before changing the full IGP.
  3. Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings.
  4. Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries.
  5. Check CE neighbor health, routing-instance interface membership, customer prefixes in instance.inet.0, VRF export policy and remote import results.

Explanation

Correct Answers

A:

The case-specific routing and services action is: Implement intended full-mesh or hub-and-spoke VPN reachability with precise route-target and policy behavior, including explicitly approved Internet access.

D:

The direct discriminating observation is: Inspect hub and spoke import/export communities, default-route presence, return routes, firewall/NAT policy and VPN-specific forwarding table entries.

Incorrect Answers

B:

This alternative proposes: Investigate rejected or down IS-IS adjacencies by verifying circuit levels, IS-IS NET identifiers, authentication and interface MTU before changing the full IGP. It concerns a different Junos engineering issue IS-IS adjacency NET and interface mismatch troubleshooting, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

C:

This alternative proposes: Validate BGP Layer 2 VPN service discovery through negotiated signaling families, route distinguishers/targets and customer connection mappings. It concerns a different Junos engineering issue BGP-signaled Layer 2 VPN NLRI and route target import, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

E:

This alternative proposes: Check CE neighbor health, routing-instance interface membership, customer prefixes in instance.inet.0, VRF export policy and remote import results. It concerns a different Junos engineering issue PE to CE routing and customer route redistribution, not the directly tested provider-network issue Layer 3 VPN hub spoke topology and controlled Internet breakout.

Service Provider Routing and Switching, Professional (JNCIP-SP) (JN0-664) Practice Tests