HP HPE7-A11 Practice Test 29
Question 280
During a brownfield campus design assessment, the team encounters this condition: A redundant core design carries required traffic at full rate normally but cannot survive a member failure without saturation. Which TWO complementary architecture elements provide the best response and directly verify the outcome? Select TWO answers.
- Calculate simultaneous worst-case delivered PoE demand with model and power-supply limits and appropriate operational headroom.
- Design supported dual attachments, multi-chassis or routed redundancy and verify failover with remaining-link capacity.
- Examine uplink endpoint diversity, LAG or routing design, alternate path capacity and single-device fault traces.
- Inspect routing adjacencies, failure path reconvergence, addressing design, bandwidth and spanning-tree fault domains.
- Assume adding a second fiber strand provides node resilience when both strands terminate on the same unprotected device.
Explanation
Correct Answers
B:Correct architect action: Design supported dual attachments, multi-chassis or routed redundancy and verify failover with remaining-link capacity.
C:Correct validation evidence: Examine uplink endpoint diversity, LAG or routing design, alternate path capacity and single-device fault traces. The current design risk is: A redundant core design carries required traffic at full rate normally but cannot survive a member failure without saturation.
Incorrect Answers
A:This is a valid design consideration for the separate topic of Access switch PoE budget and load calculation, but is not the MOST direct response to the specific issue in this case: A redundant core design carries required traffic at full rate normally but cannot survive a member failure without saturation.
D:This is a valid design consideration for the separate topic of Routed interbuilding uplinks and ECMP paths, but is not the MOST direct response to the specific issue in this case: A redundant core design carries required traffic at full rate normally but cannot survive a member failure without saturation.
E:This option would take an unsupported design shortcut: Assume adding a second fiber strand provides node resilience when both strands terminate on the same unprotected device. The described customer case is: A redundant core design carries required traffic at full rate normally but cannot survive a member failure without saturation.
Question 281
A multi-building campus architecture team discovers this obstacle: A redundant core design carries required traffic at full rate normally but cannot survive a member failure without saturation. Which observed result BEST demonstrates that the design meets the requirement? Select ONE best answer.
- Loss of one approved component retains an adequate and supported forwarding path without unacceptable service interruption.
- Assume adding a second fiber strand provides node resilience when both strands terminate on the same unprotected device.
- Uplinks meet specified service goals during normal peak load and tolerated failures without unnecessary purchased capacity.
- The selected access model confines faults and preserves authorized client services across supported routed paths.
Explanation
Correct Answer
A:The design response that should produce this result is: Design supported dual attachments, multi-chassis or routed redundancy and verify failover with remaining-link capacity.
Incorrect Answers
B:That option would assume adding a second fiber strand provides node resilience when both strands terminate on the same unprotected device, but it addresses a different concern. The design response that should produce this result is: Design supported dual attachments, multi-chassis or routed redundancy and verify failover with remaining-link capacity.
C:This is a valid design consideration for the separate topic of Oversubscription and uplink throughput budget, but is not the MOST direct response to the specific issue in this case: A redundant core design carries required traffic at full rate normally but cannot survive a member failure without saturation.
D:This is a valid design consideration for the separate topic of Layer 3 access and resilient routed uplink strategy, but is not the MOST direct response to the specific issue in this case: A redundant core design carries required traffic at full rate normally but cannot survive a member failure without saturation.
Question 282
A predeployment discovery session records this problem: A redundant core design carries required traffic at full rate normally but cannot survive a member failure without saturation. Which unsafe assumption about dual-homing and link aggregation topology capacity should the architect REJECT? Select ONE best answer.
- Assume drawing two switches beside each other proves multi-chassis redundancy even without supported peer and downstream attachment design.
- Assume every campus, regardless of size, must deploy separate core, aggregation and access tiers to be professionally designed.
- Assume ceiling area alone determines optimal AP quantity and that higher density can always be handled by raising transmit power.
- Assume adding a second fiber strand provides node resilience when both strands terminate on the same unprotected device.
Explanation
Correct Answer
D:It conflicts with the design principle: Resilient topology must eliminate common failure points and preserve enough bandwidth under the stated degradation condition.
Incorrect Answers
A:This is a valid design consideration for the separate topic of AOS-CX VSX aggregation resiliency, but is not the MOST direct response to the specific issue in this case: A redundant core design carries required traffic at full rate normally but cannot survive a member failure without saturation.
B:This is a valid design consideration for the separate topic of Two-tier collapsed-core architecture choice, but is not the MOST direct response to the specific issue in this case: A redundant core design carries required traffic at full rate normally but cannot survive a member failure without saturation.
C:This is a valid design consideration for the separate topic of Wireless AP count from capacity and coverage survey, but is not the MOST direct response to the specific issue in this case: A redundant core design carries required traffic at full rate normally but cannot survive a member failure without saturation.
Question 283
An enterprise network RFP includes the following situation: A large university links buildings through one stretched spanning-tree domain and suffers widespread outages when an edge loop occurs. What design or operational decision BEST addresses the customer requirement or risk? Select ONE best answer.
- Assume simply extending one campus VLAN across every building always provides the highest resilience and easiest troubleshooting.
- Use appropriate Layer 3 routed building connections and resilient path selection consistent with supported core and distribution design.
- Size access ports by actual closet, endpoint category, reserved uplinks, growth headroom and physical patching constraints.
- Choose AP enclosure, antenna pattern, environmental tolerance, mounting height and regulatory limits for the actual site.
Explanation
Correct Answer
B:Correct architect action: Use appropriate Layer 3 routed building connections and resilient path selection consistent with supported core and distribution design.
Incorrect Answers
A:That option would assume simply extending one campus VLAN across every building always provides the highest resilience and easiest troubleshooting, but it addresses a different concern. Engineering rationale: Routed interconnections can constrain L2 fault propagation and permit multiple active paths where routing and policy support them.
C:The targeted control is: Use appropriate Layer 3 routed building connections and resilient path selection consistent with supported core and distribution design. The critical proof is: Inspect routing adjacencies, failure path reconvergence, addressing design, bandwidth and spanning-tree fault domains.
D:This is a valid design consideration for the separate topic of Indoor outdoor AP enclosure and antenna suitability, but is not the MOST direct response to the specific issue in this case: A large university links buildings through one stretched spanning-tree domain and suffers widespread outages when an edge loop occurs.
Question 284
An HPE Aruba Networking campus design workshop faces this issue: A large university links buildings through one stretched spanning-tree domain and suffers widespread outages when an edge loop occurs. Which campus architecture principle MOST directly explains why the issue matters? Select ONE best answer.
- Routed access can limit broadcast domains and support resilient equal-cost paths, but migration alters gateway and policy assumptions.
- Assume simply extending one campus VLAN across every building always provides the highest resilience and easiest troubleshooting.
- Routed interconnections can constrain L2 fault propagation and permit multiple active paths where routing and policy support them.
- A meaningful preliminary bill of materials covers deployable solution components and recurring obligations, not only headline chassis.
Explanation
Correct Answer
C:This principle supports the recommended action: Use appropriate Layer 3 routed building connections and resilient path selection consistent with supported core and distribution design.
Incorrect Answers
A:This is a valid design consideration for the separate topic of Layer 3 access and resilient routed uplink strategy, but is not the MOST direct response to the specific issue in this case: A large university links buildings through one stretched spanning-tree domain and suffers widespread outages when an edge loop occurs.
B:That option would assume simply extending one campus VLAN across every building always provides the highest resilience and easiest troubleshooting, but it addresses a different concern. This principle supports the recommended action: Use appropriate Layer 3 routed building connections and resilient path selection consistent with supported core and distribution design.
D:This is a valid design consideration for the separate topic of Preliminary multiyear licensing and accessory BOM, but is not the MOST direct response to the specific issue in this case: A large university links buildings through one stretched spanning-tree domain and suffers widespread outages when an edge loop occurs.
Question 285
A campus solution procurement and acceptance review finds this situation: A large university links buildings through one stretched spanning-tree domain and suffers widespread outages when an edge loop occurs. Which evidence or investigation MOST directly verifies the relevant design assumption? Select ONE best answer.
- Inspect routing adjacencies, failure path reconvergence, addressing design, bandwidth and spanning-tree fault domains.
- Inspect facility electrical measurements, equipment maximum power, HVAC plans, UPS load estimates and approved outage duration.
- Assume simply extending one campus VLAN across every building always provides the highest resilience and easiest troubleshooting.
- Reconcile closet patch schedules, currently occupied and reserved interfaces, realistic expansion demand and failure spare allowances.
Explanation
Correct Answer
A:The target result is: Building interconnectivity survives designated failures while layer-two incidents remain confined to intended scopes.
Incorrect Answers
B:That option concerns Closet UPS thermal and electrical installation budget. The target result is: Building interconnectivity survives designated failures while layer-two incidents remain confined to intended scopes.
C:Instead, use this controlled approach: Use appropriate Layer 3 routed building connections and resilient path selection consistent with supported core and distribution design.
D:That option concerns Access port inventory and spare growth ratio. The target result is: Building interconnectivity survives designated failures while layer-two incidents remain confined to intended scopes.
Question 286
A university or office campus architecture review raises this issue: Two building aggregations have redundant routed uplinks but the design disables one path rather than considering validated equal-cost forwarding. What design or operational decision BEST addresses the customer requirement or risk? Select ONE best answer.
- Choose AP enclosure, antenna pattern, environmental tolerance, mounting height and regulatory limits for the actual site.
- Compare two-tier collapsed-core and three-tier architectures against campus scale, building layout, uplink needs and fault domains.
- Use appropriate Layer 3 routed building connections and resilient path selection consistent with supported core and distribution design.
- Assume simply extending one campus VLAN across every building always provides the highest resilience and easiest troubleshooting.
Explanation
Correct Answer
C:Correct architect action: Use appropriate Layer 3 routed building connections and resilient path selection consistent with supported core and distribution design.
Incorrect Answers
A:This is a valid design consideration for the separate topic of Indoor outdoor AP enclosure and antenna suitability, but is not the MOST direct response to the specific issue in this case: Two building aggregations have redundant routed uplinks but the design disables one path rather than considering validated equal-cost forwarding.
B:This is a valid design consideration for the separate topic of Two-tier collapsed-core architecture choice, but is not the MOST direct response to the specific issue in this case: Two building aggregations have redundant routed uplinks but the design disables one path rather than considering validated equal-cost forwarding.
D:This option would take an unsupported design shortcut: Assume simply extending one campus VLAN across every building always provides the highest resilience and easiest troubleshooting. The described customer case is: Two building aggregations have redundant routed uplinks but the design disables one path rather than considering validated equal-cost forwarding.
Question 287
A professional campus access architect reviews a customer request: Two building aggregations have redundant routed uplinks but the design disables one path rather than considering validated equal-cost forwarding. Which observed result BEST demonstrates that the design meets the requirement? Select ONE best answer.
- Building interconnectivity survives designated failures while layer-two incidents remain confined to intended scopes.
- Assume simply extending one campus VLAN across every building always provides the highest resilience and easiest troubleshooting.
- Each link BOM lists interoperable optics and cabling that meet the installed distance and switch-interface specifications.
- Installed access points remain serviceable in their environment and deliver designed signal and capacity to intended areas.
Explanation
Correct Answer
A:The design response that should produce this result is: Use appropriate Layer 3 routed building connections and resilient path selection consistent with supported core and distribution design.
Incorrect Answers
B:That option would assume simply extending one campus VLAN across every building always provides the highest resilience and easiest troubleshooting, but it addresses a different concern. The design response that should produce this result is: Use appropriate Layer 3 routed building connections and resilient path selection consistent with supported core and distribution design.
C:This is a valid design consideration for the separate topic of Fiber optic transceiver pairing and distance constraints, but is not the MOST direct response to the specific issue in this case: Two building aggregations have redundant routed uplinks but the design disables one path rather than considering validated equal-cost forwarding.
D:This is a valid design consideration for the separate topic of Indoor outdoor AP enclosure and antenna suitability, but is not the MOST direct response to the specific issue For this situation: Two building aggregations have redundant routed uplinks but the design disables one path rather than considering validated equal-cost forwarding.
Question 288
A technical solution proposal must address the following case: Two building aggregations have redundant routed uplinks but the design disables one path rather than considering validated equal-cost forwarding. Which unsafe assumption about routed interbuilding uplinks and ecmp paths should the architect REJECT? Select ONE best answer.
- Assume advertised Wi-Fi radio throughput guarantees application throughput even on undersized wired uplinks or power-limited ports.
- Assume unoccupied ports in a remote building can replace missing physical patch capacity in the closet serving a new floor.
- Assume a routed uplink automatically solves all campus loops and segmentation policy without planning gateway and client reachability.
- Assume simply extending one campus VLAN across every building always provides the highest resilience and easiest troubleshooting.
Explanation
Correct Answer
D:It conflicts with the design principle: Routed interconnections can constrain L2 fault propagation and permit multiple active paths where routing and policy support them.
Incorrect Answers
A:This is a valid design consideration for the separate topic of Multigigabit AP access uplink and power planning, but is not the MOST direct response to the specific issue in this case: Two building aggregations have redundant routed uplinks but the design disables one path rather than considering validated equal-cost forwarding.
B:This is a valid design consideration for the separate topic of Access port inventory and spare growth ratio, but is not the MOST direct response to the specific issue in this case: Two building aggregations have redundant routed uplinks but the design disables one path rather than considering validated equal-cost forwarding.
C:This is a valid design consideration for the separate topic of Layer 3 access and resilient routed uplink strategy, but is not the MOST direct response to the specific issue in this case: Two building aggregations have redundant routed uplinks but the design disables one path rather than considering validated equal-cost forwarding.
Question 289
A customer design-defense meeting examines the following constraint: An auditorium vendor quotes one AP per hundred square meters while events have high simultaneous device density. What design or operational decision BEST addresses the customer requirement or risk? Select ONE best answer.
- Build a preliminary BOM including supported hardware, software entitlements, management subscriptions, optics, support and site dependencies.
- Assume ceiling area alone determines optimal AP quantity and that higher density can always be handled by raising transmit power.
- Select a supported VSX pair for aggregation or core redundancy and document peer connectivity, downstream LAG and failure testing.
- Determine AP locations using coverage, client density, application throughput, RF interference and practical deployment constraints together.
Explanation
Correct Answer
D:Correct architect action: Determine AP locations using coverage, client density, application throughput, RF interference and practical deployment constraints together.
Incorrect Answers
A:The targeted control is: Determine AP locations using coverage, client density, application throughput, RF interference and practical deployment constraints together. The critical proof is: Review site survey and heatmap, associated client counts, busy-hour airtime, capacity targets and alternative AP placements.
B:That option would assume ceiling area alone determines optimal AP quantity and that higher density can always be handled by raising transmit power, but it addresses a different concern. Engineering rationale: AP counts must satisfy both radio coverage and airtime capacity; different occupancy and materials can change requirements.
C:This is a valid design consideration for the separate topic of AOS-CX VSX aggregation resiliency, but is not the MOST direct response to the specific issue in this case: An auditorium vendor quotes one AP per hundred square meters while events have high simultaneous device density.
Question 290
During a brownfield campus design assessment, the team encounters this condition: An auditorium vendor quotes one AP per hundred square meters while events have high simultaneous device density. Which TWO complementary architecture elements provide the best response and directly verify the outcome? Select TWO answers.
- Assume ceiling area alone determines optimal AP quantity and that higher density can always be handled by raising transmit power.
- Review site survey and heatmap, associated client counts, busy-hour airtime, capacity targets and alternative AP placements.
- Calculate simultaneous worst-case delivered PoE demand with model and power-supply limits and appropriate operational headroom.
- Determine AP locations using coverage, client density, application throughput, RF interference and practical deployment constraints together.
- Inspect official AP installation data, switch interface matrix, PSE power classes, cabling certification and prototype negotiation.
Explanation
Correct Answers
B:Correct validation evidence: Review site survey and heatmap, associated client counts, busy-hour airtime, capacity targets and alternative AP placements. The current design risk is: An auditorium vendor quotes one AP per hundred square meters while events have high simultaneous device density.
D:Correct architect Recommended action: Determine AP locations using coverage, client density, application throughput, RF interference and practical deployment constraints together.
Incorrect Answers
A:This option would take an unsupported design shortcut: Assume ceiling area alone determines optimal AP quantity and that higher density can always be handled by raising transmit power. The described customer case is: An auditorium vendor quotes one AP per hundred square meters while events have high simultaneous device density.
C:That option concerns Access switch PoE budget and load calculation. The target result is: Required user density meets measured RF and application performance without avoidable channel contention or coverage gaps.
E:That option concerns Multigigabit AP access uplink and power planning. The target result is: Required user density meets measured RF and application performance without avoidable channel contention or coverage gaps.