cert
cert-1
cert-2

Pass Fortinet NSE5_FSW_AD-7.6 Exam in First Attempt Guaranteed!

Get 100% Latest Exam Questions, Accurate & Verified Answers to Pass the Actual Exam!
30 Days Free Updates, Instant Download!

cert-5
cert-6
NSE5_FSW_AD-7.6 Exam - Verified By Experts
NSE5_FSW_AD-7.6 Premium File

NSE5_FSW_AD-7.6 Premium File

$69.99
$76.99
  • Premium File 64 Questions & Answers. Last Update: Nov 15, 2026

Whats Included:

  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
 
$76.99
$69.99
accept 42 downloads in the last 7 days
block-screenshots
Fortinet NSE5_FSW_AD-7.6 Practice Test 50

Question 490

A video stream reaches all desks even though only two phones subscribe to the multicast group. Which FortiSwitch configuration or corrective action BEST addresses the requirement?

  1. Build a documented supported FortiSwitch daisy chain or multi-tier topology with adequate ISL uplink capacity and safeguards.
  2. Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context.
  3. Choose static, active or passive LACP trunk behavior consistently between peers and verify member aggregation.
  4. Configure supported IGMP snooping and querier expectations to forward multicast only where receivers request it.

Explanation

Correct Answer

D:

Configure supported IGMP snooping and querier expectations to forward multicast only where receivers request it. A multicast VLAN alone does not indicate that IGMP receiver membership or querier operation is healthy. Verify the action with: Check group membership table, querier identity, IGMP report traffic, VLAN and target egress port.

Incorrect Answers

A:

Build a documented supported FortiSwitch daisy chain or multi-tier topology with adequate ISL uplink capacity and safeguards. This action is relevant to FortiSwitch multi-tier managed topology, not the controlling requirement in this case. A FortiGate controls each FortiSwitch through the managed Layer-2 topology, but downstream reachability depends on upstream FortiLink links. The targeted response is: Configure supported IGMP snooping and querier expectations to forward multicast only where receivers request it.

B:

Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context. This action is relevant to FortiSwitch SVI routing and connected routes, not the controlling requirement in this case. Layer-3 SVI configuration and actual usable forwarding are separate from having a named Layer-2 VLAN. The targeted response is: Configure supported IGMP snooping and querier expectations to forward multicast only where receivers request it.

C:

Choose static, active or passive LACP trunk behavior consistently between peers and verify member aggregation. This action is relevant to LACP negotiation on FortiSwitch FortiLink trunks, not the controlling requirement in this case. Passive LACP on both ends may not negotiate an active bundle, and individual green links do not prove aggregation. The targeted response is: Configure supported IGMP snooping and querier expectations to forward multicast only where receivers request it.

Question 491

A branch uplink uses a multimode optic across a single-mode campus fiber run and never achieves light. Which FortiSwitch configuration or corrective action BEST addresses the requirement?

  1. Choose supported Fortinet transceivers and link media based on switch capability, optical reach and wavelength.
  2. Apply a specific restricted VLAN or quarantine mechanism with explicit authorized remediation and monitoring expectations.
  3. Correlate stack and ISL status to identify the failed path instead of reconfiguring all access VLANs.
  4. Set only mutually supported Ethernet port rates and verify operational negotiation instead of forcing mismatched speeds.

Explanation

Correct Answer

A:

Choose supported Fortinet transceivers and link media based on switch capability, optical reach and wavelength. Matching a mechanical optic cage is insufficient to prove optical or firmware compatibility. Verify the action with: Inspect transceiver SKU, supported compatibility table, Tx/Rx optical power, interface alarms and cable plant type.

Incorrect Answers

B:

Apply a specific restricted VLAN or quarantine mechanism with explicit authorized remediation and monitoring expectations. This action is relevant to VLAN security policy and quarantine actions, not the controlling requirement in this case. Quarantine must be enforced at the right switch and VLAN path; a security-alert label alone does not remove access. The targeted response is: Choose supported Fortinet transceivers and link media based on switch capability, optical reach and wavelength.

C:

Correlate stack and ISL status to identify the failed path instead of reconfiguring all access VLANs. This action is relevant to Stack failure isolation and switch-to-switch port roles, not the controlling requirement in this case. A missing switch in a FortiLink managed chain may be caused by the upstream ISL even if its access ports still carry local traffic. The targeted response is: Choose supported Fortinet transceivers and link media based on switch capability, optical reach and wavelength.

D:

Set only mutually supported Ethernet port rates and verify operational negotiation instead of forcing mismatched speeds. This action is relevant to Switch port speed and duplex commissioning, not the controlling requirement in this case. Incorrect forced port speed or duplex can mimic application loss even when the VLAN configuration is valid. The targeted response is: Choose supported Fortinet transceivers and link media based on switch capability, optical reach and wavelength.

Question 492

A branch's FortiLink interface has no route or reachable controller IP and the managed switch never appears. Which TWO complementary steps identify the appropriate FortiSwitch response AND the evidence needed to verify it? Select TWO.

  1. Inspect shared-port VLAN diff, tenant inventory, VDOM policy, change approval and representative positive/negative access tests.
  2. Authorized endpoints enter only permitted VLANs while failed authentication is denied or restricted according to policy.
  3. Check interface type, FortiLink enablement, discovery setting, IP assignment, switch model support, and management VLAN reachability.
  4. Create an appropriate FortiGate FortiLink physical or logical interface with supported addressing and controller capabilities before onboarding a switch.
  5. Build a documented supported FortiSwitch daisy chain or multi-tier topology with adequate ISL uplink capacity and safeguards.

Explanation

Correct Answers

C:

Check interface type, FortiLink enablement, discovery setting, IP assignment, switch model support, and management VLAN reachability. A FortiGate port not configured for FortiLink cannot assume managed-switch ownership from physical connection alone. The paired action is: Create an appropriate FortiGate FortiLink physical or logical interface with supported addressing and controller capabilities before onboarding a switch. This is the diagnostic or verification half of the requested TWO-step pair.

D:

Create an appropriate FortiGate FortiLink physical or logical interface with supported addressing and controller capabilities before onboarding a switch. A FortiGate port not configured for FortiLink cannot assume managed-switch ownership from physical connection alone. Verify the action with: Check interface type, FortiLink enablement, discovery setting, IP assignment, switch model support, and management VLAN reachability. This is the configuration or remediation half of the requested TWO-step pair.

Incorrect Answers

A:

Inspect shared-port VLAN diff, tenant inventory, VDOM policy, change approval and representative positive/negative access tests. This step concerns Multi-tenant change verification and rollback and is not part of the required paired solution. The correct action and evidence are: Create an appropriate FortiGate FortiLink physical or logical interface with supported addressing and controller capabilities before onboarding a switch. Together with: Check interface type, FortiLink enablement, discovery setting, IP assignment, switch model support, and management VLAN reachability.

B:

Authorized endpoints enter only permitted VLANs while failed authentication is denied or restricted according to policy. This step concerns FortiSwitch 802.1X port-based authentication and is not part of the required paired solution. The correct action and evidence are: Create an appropriate FortiGate FortiLink physical or logical interface with supported addressing and controller capabilities before onboarding a switch. Together with: Check interface type, FortiLink enablement, discovery setting, IP assignment, switch model support, and management VLAN reachability.

E:

Build a documented supported FortiSwitch daisy chain or multi-tier topology with adequate ISL uplink capacity and safeguards. This step concerns FortiSwitch multi-tier managed topology and is not part of the required paired solution. The correct action and evidence are: Create an appropriate FortiGate FortiLink physical or logical interface with supported addressing and controller capabilities before onboarding a switch. Together with: Check interface type, FortiLink enablement, discovery setting, IP assignment, switch model support, and management VLAN reachability.

Question 493

A third-party optic fits the switch but platform logs report it as unsupported after a firmware change. Which diagnostic evidence should the FortiSwitch administrator examine FIRST?

  1. Inspect power supply reserve, current draw, negotiated PoE class, priority shedding and port events.
  2. Inspect transceiver SKU, supported compatibility table, Tx/Rx optical power, interface alarms and cable plant type.
  3. Check per-member speed, partner identity, state, optical counters, VLAN tags and aggregate distribution.
  4. Review target VLAN, switch isolation controls, client MAC table, permitted gateway path and peer-to-peer test.

Explanation

Correct Answer

B:

Inspect transceiver SKU, supported compatibility table, Tx/Rx optical power, interface alarms and cable plant type. Matching a mechanical optic cage is insufficient to prove optical or firmware compatibility. The paired action is: Choose supported Fortinet transceivers and link media based on switch capability, optical reach and wavelength.

Incorrect Answers

A:

Inspect power supply reserve, current draw, negotiated PoE class, priority shedding and port events. These observations are applicable to Power over Ethernet port controls and budgets, but would not isolate the main failure first. The decisive evidence is: Inspect transceiver SKU, supported compatibility table, Tx/Rx optical power, interface alarms and cable plant type.

C:

Check per-member speed, partner identity, state, optical counters, VLAN tags and aggregate distribution. These observations are applicable to Link aggregation and port error recovery, but would not isolate the main failure first. The decisive evidence is: Inspect transceiver SKU, supported compatibility table, Tx/Rx optical power, interface alarms and cable plant type.

D:

Review target VLAN, switch isolation controls, client MAC table, permitted gateway path and peer-to-peer test. These observations are applicable to Intra-VLAN blocking and isolation boundaries, but would not isolate the main failure first. The decisive evidence is: Inspect transceiver SKU, supported compatibility table, Tx/Rx optical power, interface alarms and cable plant type.

Question 494

A network engineer selects a breakout option not supported by its FortiSwitch hardware revision. Which diagnostic evidence should the FortiSwitch administrator examine FIRST?

  1. Check captured port, protocol/MAC/IP filter, platform buffer capacity, capture timestamps and exported packet headers.
  2. Inspect the port native VLAN, allowed VLAN list, peer tags, learned MACs and relevant FortiGate VLAN interface.
  3. Inspect hardware SKU, firmware and phy-mode support, breakout cable specification, child port IDs and port restart effect.
  4. Inspect guard role, BPDU reception, root-ID history, STP port role and loop-condition log.

Explanation

Correct Answer

C:

Inspect hardware SKU, firmware and phy-mode support, breakout cable specification, child port IDs and port restart effect. A physical QSFP cage does not guarantee that four independent Ethernet child ports can be enabled on every model. The paired action is: Check that selected switch series and transceiver support split port or PHY breakout, and plan the related interface remapping.

Incorrect Answers

A:

Check captured port, protocol/MAC/IP filter, platform buffer capacity, capture timestamps and exported packet headers. These observations are applicable to FortiSwitch local packet-capture profile and filters, but would not isolate the main failure first. The decisive evidence is: Inspect hardware SKU, firmware and phy-mode support, breakout cable specification, child port IDs and port restart effect.

B:

Inspect the port native VLAN, allowed VLAN list, peer tags, learned MACs and relevant FortiGate VLAN interface. These observations are applicable to FortiSwitch native VLAN versus allowed VLANs, but would not isolate the main failure first. The decisive evidence is: Inspect hardware SKU, firmware and phy-mode support, breakout cable specification, child port IDs and port restart effect.

D:

Inspect guard role, BPDU reception, root-ID history, STP port role and loop-condition log. These observations are applicable to Root guard and loop guard failure response, but would not isolate the main failure first. The decisive evidence is: Inspect hardware SKU, firmware and phy-mode support, breakout cable specification, child port IDs and port restart effect.

Question 495

An office printer sends DHCP Discover repeatedly but never sees an Offer after a trust-boundary change. Which FortiSwitch configuration or corrective action BEST addresses the requirement?

  1. Trace DHCP and ARP exchanges at ingress and uplink to distinguish missing requests from blocked or malformed responses.
  2. Use a supported FortiGate one-arm sniffer or mirrored ingress path to inspect switch traffic where permitted.
  3. Set measured storm-control thresholds for broadcast, multicast or unknown unicast as supported and validate needed discovery protocols.
  4. Use FortiGate FortiSwitch Ports statistics or supported switch commands to isolate errors, utilization and port status at the right location.

Explanation

Correct Answer

A:

Trace DHCP and ARP exchanges at ingress and uplink to distinguish missing requests from blocked or malformed responses. A DHCP lease failure can originate at the client, switch, relay or server; capturing at one side alone is not always conclusive. Verify the action with: Inspect Discover/Offer/Request/Ack sequence, ARP requests/replies, VLAN tags, DHCP snooping and DAI counters.

Incorrect Answers

B:

Use a supported FortiGate one-arm sniffer or mirrored ingress path to inspect switch traffic where permitted. This action is relevant to FortiGate one-arm sniffer across managed switching, not the controlling requirement in this case. Sniffer placement determines visibility; absence of a packet at one observation point does not prove no packet existed elsewhere. The targeted response is: Trace DHCP and ARP exchanges at ingress and uplink to distinguish missing requests from blocked or malformed responses.

C:

Set measured storm-control thresholds for broadcast, multicast or unknown unicast as supported and validate needed discovery protocols. This action is relevant to Storm-control thresholds and broadcast containment, not the controlling requirement in this case. Overaggressive storm control can break DHCP, ARP or group discovery even when physical links remain healthy. The targeted response is: Trace DHCP and ARP exchanges at ingress and uplink to distinguish missing requests from blocked or malformed responses.

D:

Use FortiGate FortiSwitch Ports statistics or supported switch commands to isolate errors, utilization and port status at the right location. This action is relevant to Managed switch port statistics and counter analysis, not the controlling requirement in this case. A port-up indicator or one successful ping is not proof that a congested or errored uplink is healthy. The targeted response is: Trace DHCP and ARP exchanges at ingress and uplink to distinguish missing requests from blocked or malformed responses.

Question 496

An attacker spoofs the default gateway MAC using gratuitous ARP on a guest user VLAN. Which observable result BEST proves the intended FortiSwitch operation or security policy works?

  1. Phones and access points receive stable allocated power while redundant PSU and priority policies remain within budget.
  2. Port traffic follows the assigned access security requirement without arbitrary drift after controller synchronization.
  3. Spoofed ARP replies are dropped while legitimate endpoints maintain gateway ARP resolution.
  4. Only intended traffic is accepted or rejected at the switch while allowed application sessions remain functional.

Explanation

Correct Answer

C:

Spoofed ARP replies are dropped while legitimate endpoints maintain gateway ARP resolution. DAI validation needs a reliable binding or exception policy; enabling it blindly can interrupt static-IP devices.

Incorrect Answers

A:

Phones and access points receive stable allocated power while redundant PSU and priority policies remain within budget. This result relates to PoE and LLDP-MED endpoint power coordination, not the acceptance condition under test. The relevant result is: Spoofed ARP replies are dropped while legitimate endpoints maintain gateway ARP resolution.

B:

Port traffic follows the assigned access security requirement without arbitrary drift after controller synchronization. This result relates to FortiSwitch security profile application and precedence, not the acceptance condition under test. The relevant result is: Spoofed ARP replies are dropped while legitimate endpoints maintain gateway ARP resolution.

D:

Only intended traffic is accepted or rejected at the switch while allowed application sessions remain functional. This result relates to Static port ACL forwarding decisions, not the acceptance condition under test. The relevant result is: Spoofed ARP replies are dropped while legitimate endpoints maintain gateway ARP resolution.

Question 497

A branch turns off 802.1X to fix an outage and inadvertently permits visitors onto production VLANs. Which FortiSwitch configuration or corrective action BEST addresses the requirement?

  1. Use documented trusted DHCP-server lists or Option 82 information where supported to enforce authorized address assignment.
  2. Correlate LLDP neighbor inventory and VLAN-specific MAC entries to reconstruct actual endpoint and uplink paths.
  3. Configure supported IEEE 802.1X port security against an approved RADIUS service with explicit guest/unauthorized behavior.
  4. Apply a specific restricted VLAN or quarantine mechanism with explicit authorized remediation and monitoring expectations.

Explanation

Correct Answer

C:

Configure supported IEEE 802.1X port security against an approved RADIUS service with explicit guest/unauthorized behavior. A physical link can be up while 802.1X blocks traffic; the switch is the authenticator, not the authentication server. Verify the action with: Inspect supplicant EAP exchange, RADIUS reachability, shared secret, port policy, authentication result and assigned access profile.

Incorrect Answers

A:

Use documented trusted DHCP-server lists or Option 82 information where supported to enforce authorized address assignment. This action is relevant to DHCP server allowlist and Option 82 validation, not the controlling requirement in this case. DHCP server allowlist and Option 82 metadata provide additional context but cannot correct a failed VLAN or missing upstream relay. The targeted response is: Configure supported IEEE 802.1X port security against an approved RADIUS service with explicit guest/unauthorized behavior.

B:

Correlate LLDP neighbor inventory and VLAN-specific MAC entries to reconstruct actual endpoint and uplink paths. This action is relevant to LLDP and MAC forwarding table extraction, not the controlling requirement in this case. LLDP provides adjacent-device identity, while MAC learning maps forwarding; neither is a full routed trace by itself. The targeted response is: Configure supported IEEE 802.1X port security against an approved RADIUS service with explicit guest/unauthorized behavior.

D:

Apply a specific restricted VLAN or quarantine mechanism with explicit authorized remediation and monitoring expectations. This action is relevant to VLAN security policy and quarantine actions, not the controlling requirement in this case. Quarantine must be enforced at the right switch and VLAN path; a security-alert label alone does not remove access. The targeted response is: Configure supported IEEE 802.1X port security against an approved RADIUS service with explicit guest/unauthorized behavior.

Question 498

A conference room allows one phone and one PC but an overstrict MAC learning limit blocks the PC. Which diagnostic evidence should the FortiSwitch administrator examine FIRST?

  1. Examine port binding list, packet source IP, ingress VLAN, IP-source guard counters and expected host subnet.
  2. Review filter minimization, capture duration, administrator authorization, sensitive payloads and evidence-sharing restrictions.
  3. Inspect MAC table usage, configured learning limit, learned device count, port-security event and violation action.
  4. Inspect device fingerprint, policy rule order, assigned VLAN, security profile, client identity and enforcement state.

Explanation

Correct Answer

C:

Inspect MAC table usage, configured learning limit, learned device count, port-security event and violation action. Dynamic MAC learning limits reduce accidental fan-out but should be tuned for legitimate multi-device access designs. The paired action is: Set model-supported dynamic MAC address learning limits and specific violation action on access-facing switch ports.

Incorrect Answers

A:

Examine port binding list, packet source IP, ingress VLAN, IP-source guard counters and expected host subnet. These observations are applicable to IPv4 source guard and binding-based packet filtering, but would not isolate the main failure first. The decisive evidence is: Inspect MAC table usage, configured learning limit, learned device count, port-security event and violation action.

B:

Review filter minimization, capture duration, administrator authorization, sensitive payloads and evidence-sharing restrictions. These observations are applicable to Capture and confidentiality limits in incident response, but would not isolate the main failure first. The decisive evidence is: Inspect MAC table usage, configured learning limit, learned device count, port-security event and violation action.

D:

Inspect device fingerprint, policy rule order, assigned VLAN, security profile, client identity and enforcement state. These observations are applicable to NAC dynamic port policy device classification, but would not isolate the main failure first. The decisive evidence is: Inspect MAC table usage, configured learning limit, learned device count, port-security event and violation action.

Question 499

An operator puts a VLAN under a WAN interface instead of the FortiLink interface used by the branch switches. Which FortiSwitch configuration or corrective action BEST addresses the requirement?

  1. Use supported native and voice VLAN policies so phones and downstream workstations receive appropriate separate traffic treatment.
  2. Prepare supported provisioning, DHCP, management connectivity and secure bootstrap before assuming a factory-default FortiSwitch will auto-configure.
  3. Configure supported FortiSwitch MCLAG peer groups and peer links before connecting downstream redundant bundles.
  4. Build FortiSwitch VLAN interfaces in the correct FortiLink context and assign ports through the managed switch controller.

Explanation

Correct Answer

D:

Build FortiSwitch VLAN interfaces in the correct FortiLink context and assign ports through the managed switch controller. A named VLAN in FortiOS is not proof its switch-port membership and L3 policy are correct. Verify the action with: Check FortiLink parent, VLAN ID, VDOM membership, port assignment, subnet and firewall-policy path.

Incorrect Answers

A:

Use supported native and voice VLAN policies so phones and downstream workstations receive appropriate separate traffic treatment. This action is relevant to Voice and data VLAN separation on shared access ports, not the controlling requirement in this case. Voice tagging is not secured merely because its VLAN ID differs from the workstation's native VLAN. The targeted response is: Build FortiSwitch VLAN interfaces in the correct FortiLink context and assign ports through the managed switch controller.

B:

Prepare supported provisioning, DHCP, management connectivity and secure bootstrap before assuming a factory-default FortiSwitch will auto-configure. This action is relevant to Zero-touch provisioning and controller dependency checks, not the controlling requirement in this case. Zero-touch deployment works only when the necessary discovery path and identity checks function; a link LED is insufficient. The targeted response is: Build FortiSwitch VLAN interfaces in the correct FortiLink context and assign ports through the managed switch controller.

C:

Configure supported FortiSwitch MCLAG peer groups and peer links before connecting downstream redundant bundles. This action is relevant to MCLAG peer-link topology for managed access switches, not the controlling requirement in this case. MCLAG redundancy depends on supported peer-link and aggregate design; two cables alone do not constitute working multichassis aggregation. The targeted response is: Build FortiSwitch VLAN interfaces in the correct FortiLink context and assign ports through the managed switch controller.

Question 500

An administrator installs an ACL on the wrong ingress switch port and sees no change in affected traffic. Which TWO complementary steps identify the appropriate FortiSwitch response AND the evidence needed to verify it? Select TWO.

  1. Apply supported switch ACL entries to targeted port or VLAN traffic with documented match, action, and policy sequence.
  2. Inspect port profile assignment, FortiGate controller policy, client role, enforcement counters and overlapping static controls.
  3. Review ACL direction and attachment, permit/drop rules, hit counters, supported match fields and resulting packet path.
  4. Rapid MAC moves stop and normal forwarding returns with a verified alternate redundant path.
  5. Verify dynamic ACL assignment from RADIUS after successful 802.1X and account for platform rule and IPv4 support constraints.

Explanation

Correct Answers

A:

Apply supported switch ACL entries to targeted port or VLAN traffic with documented match, action, and policy sequence. Switch ACLs and FortiGate firewall policies operate at different enforcement points; a deny on one does not prove the other applied. Verify the action with: Review ACL direction and attachment, permit/drop rules, hit counters, supported match fields and resulting packet path. This is the configuration or remediation half of the requested TWO-step pair.

C:

Review ACL direction and attachment, permit/drop rules, hit counters, supported match fields and resulting packet path. Switch ACLs and FortiGate firewall policies operate at different enforcement points; a deny on one does not prove the other applied. The paired action is: Apply supported switch ACL entries to targeted port or VLAN traffic with documented match, action, and policy sequence. This is the diagnostic or verification half of the requested TWO-step pair.

Incorrect Answers

B:

Inspect port profile assignment, FortiGate controller policy, client role, enforcement counters and overlapping static controls. This step concerns FortiSwitch security profile application and precedence and is not part of the required paired solution. The correct action and evidence are: Apply supported switch ACL entries to targeted port or VLAN traffic with documented match, action, and policy sequence. Together with: Review ACL direction and attachment, permit/drop rules, hit counters, supported match fields and resulting packet path.

D:

Rapid MAC moves stop and normal forwarding returns with a verified alternate redundant path. This step concerns STP incident recovery with MAC flap evidence and is not part of the required paired solution. The correct action and evidence are: Apply supported switch ACL entries to targeted port or VLAN traffic with documented match, action, and policy sequence. Together with: Review ACL direction and attachment, permit/drop rules, hit counters, supported match fields and resulting packet path.

E:

Verify dynamic ACL assignment from RADIUS after successful 802.1X and account for platform rule and IPv4 support constraints. This step concerns DACL RADIUS attribute and per-session enforcement and is not part of the required paired solution. The correct action and evidence are: Apply supported switch ACL entries to targeted port or VLAN traffic with documented match, action, and policy sequence. Together with: Review ACL direction and attachment, permit/drop rules, hit counters, supported match fields and resulting packet path.

Fortinet NSE 5 - FortiSwitch 7.6 Administrator (NSE5_FSW_AD-7.6) Practice Tests