cert
cert-1
cert-2

Pass Fortinet NSE5_FSW_AD-7.6 Exam in First Attempt Guaranteed!

Get 100% Latest Exam Questions, Accurate & Verified Answers to Pass the Actual Exam!
30 Days Free Updates, Instant Download!

cert-5
cert-6
NSE5_FSW_AD-7.6 Exam - Verified By Experts
NSE5_FSW_AD-7.6 Premium File

NSE5_FSW_AD-7.6 Premium File

$69.99
$76.99
  • Premium File 64 Questions & Answers. Last Update: Nov 15, 2026

Whats Included:

  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
 
$76.99
$69.99
accept 42 downloads in the last 7 days
block-screenshots
Fortinet NSE5_FSW_AD-7.6 Practice Test 47

Question 460

A technician plugs a managed FortiSwitch into an arbitrary WAN port and waits for it to register automatically. Which TWO complementary steps identify the appropriate FortiSwitch response AND the evidence needed to verify it? Select TWO.

  1. A redundant topology recovers after a link failure without simultaneous independent forwarding paths causing loops.
  2. Inspect primary/secondary FortiGate roles, HA health, FortiLink uplinks, downstream switch topology and session continuity.
  3. Create an appropriate FortiGate FortiLink physical or logical interface with supported addressing and controller capabilities before onboarding a switch.
  4. Check interface type, FortiLink enablement, discovery setting, IP assignment, switch model support, and management VLAN reachability.
  5. Document tenant-specific impact, current switch state and reversal steps before changing shared FortiLink VLAN/port mappings.

Explanation

Correct Answers

C:

Create an appropriate FortiGate FortiLink physical or logical interface with supported addressing and controller capabilities before onboarding a switch. A FortiGate port not configured for FortiLink cannot assume managed-switch ownership from physical connection alone. Verify the action with: Check interface type, FortiLink enablement, discovery setting, IP assignment, switch model support, and management VLAN reachability. This is the configuration or remediation half of the requested TWO-step pair.

D:

Check interface type, FortiLink enablement, discovery setting, IP assignment, switch model support, and management VLAN reachability. A FortiGate port not configured for FortiLink cannot assume managed-switch ownership from physical connection alone. The paired action is: Create an appropriate FortiGate FortiLink physical or logical interface with supported addressing and controller capabilities before onboarding a switch. This is the diagnostic or verification half of the requested TWO-step pair.

Incorrect Answers

A:

A redundant topology recovers after a link failure without simultaneous independent forwarding paths causing loops. This step concerns FortiLink split-interface and standby path design and is not part of the required paired solution. The correct action and evidence are: Create an appropriate FortiGate FortiLink physical or logical interface with supported addressing and controller capabilities before onboarding a switch. Together with: Check interface type, FortiLink enablement, discovery setting, IP assignment, switch model support, and management VLAN reachability.

B:

Inspect primary/secondary FortiGate roles, HA health, FortiLink uplinks, downstream switch topology and session continuity. This step concerns HA FortiGate pair managing switch topology and is not part of the required paired solution. The correct action and evidence are: Create an appropriate FortiGate FortiLink physical or logical interface with supported addressing and controller capabilities before onboarding a switch. Together with: Check interface type, FortiLink enablement, discovery setting, IP assignment, switch model support, and management VLAN reachability.

E:

Document tenant-specific impact, current switch state and reversal steps before changing shared FortiLink VLAN/port mappings. This step concerns Multi-tenant change verification and rollback and is not part of the required paired solution. The correct action and evidence are: Create an appropriate FortiGate FortiLink physical or logical interface with supported addressing and controller capabilities before onboarding a switch. Together with: Check interface type, FortiLink enablement, discovery setting, IP assignment, switch model support, and management VLAN reachability.

Question 461

An engineer trusts every edge port to stop false positives, removing the anti-spoofing boundary. Which diagnostic evidence should the FortiSwitch administrator examine FIRST?

  1. Check interface type, FortiLink enablement, discovery setting, IP assignment, switch model support, and management VLAN reachability.
  2. Check learned client MAC, RADIUS MAC authentication response, access policy, fallback sequence and effective VLAN.
  3. Review RADIUS Access-Accept attributes, CoA path, session identifier, switch port role, DACL installation and packet test.
  4. Inspect ARP inspection status, DHCP snooping binding database, source MAC/IP, trusted ports and violation logs.

Explanation

Correct Answer

D:

Inspect ARP inspection status, DHCP snooping binding database, source MAC/IP, trusted ports and violation logs. DAI validation needs a reliable binding or exception policy; enabling it blindly can interrupt static-IP devices. The paired action is: Use supported dynamic ARP inspection with valid switch bindings to reject spoofed IP-MAC claims at untrusted edges.

Incorrect Answers

A:

Check interface type, FortiLink enablement, discovery setting, IP assignment, switch model support, and management VLAN reachability. These observations are applicable to FortiLink management interface provisioning, but would not isolate the main failure first. The decisive evidence is: Inspect ARP inspection status, DHCP snooping binding database, source MAC/IP, trusted ports and violation logs.

B:

Check learned client MAC, RADIUS MAC authentication response, access policy, fallback sequence and effective VLAN. These observations are applicable to MAC-based authentication and restricted legacy devices, but would not isolate the main failure first. The decisive evidence is: Inspect ARP inspection status, DHCP snooping binding database, source MAC/IP, trusted ports and violation logs.

C:

Review RADIUS Access-Accept attributes, CoA path, session identifier, switch port role, DACL installation and packet test. These observations are applicable to RADIUS change of authorization and applied session policy, but would not isolate the main failure first. The decisive evidence is: Inspect ARP inspection status, DHCP snooping binding database, source MAC/IP, trusted ports and violation logs.

Question 462

A rogue laptop runs a DHCP server and offers incorrect gateways to clients on an access switch. Which observable result BEST proves the intended FortiSwitch operation or security policy works?

  1. Legitimate clients lease addresses while rogue DHCP servers connected to untrusted access ports cannot answer.
  2. A session's effective access changes only when the authorization result is accepted and policy is installed on hardware.
  3. Unauthorized source IP packets fail while an approved host continues using its assigned IP and address policy.
  4. The intended VLAN survives a switch restart without unexpected controller overwrite or unauthorized local change.

Explanation

Correct Answer

A:

Legitimate clients lease addresses while rogue DHCP servers connected to untrusted access ports cannot answer. Trusting every port defeats DHCP snooping and wrongly distrusting the server uplink may suppress all leases.

Incorrect Answers

B:

A session's effective access changes only when the authorization result is accepted and policy is installed on hardware. This result relates to RADIUS change of authorization and applied session policy, not the acceptance condition under test. The relevant result is: Legitimate clients lease addresses while rogue DHCP servers connected to untrusted access ports cannot answer.

C:

Unauthorized source IP packets fail while an approved host continues using its assigned IP and address policy. This result relates to IPv4 source guard and binding-based packet filtering, not the acceptance condition under test. The relevant result is: Legitimate clients lease addresses while rogue DHCP servers connected to untrusted access ports cannot answer.

D:

The intended VLAN survives a switch restart without unexpected controller overwrite or unauthorized local change. This result relates to VLAN configuration persistence and drift control, not the acceptance condition under test. The relevant result is: Legitimate clients lease addresses while rogue DHCP servers connected to untrusted access ports cannot answer.

Question 463

A team interprets seeing a DHCP Discover at the mirror as proof the server's Offer reached the requesting access port. Which TWO complementary steps identify the appropriate FortiSwitch response AND the evidence needed to verify it? Select TWO.

  1. Review frame error type, CRC/FCS, traffic rates, drops, operational speed, port description and sampled timestamps.
  2. Investigate managed switch offline or configuration mismatch after firmware upgrade or controller resynchronization using both endpoints.
  3. The intended VLAN survives a switch restart without unexpected controller overwrite or unauthorized local change.
  4. Use a supported FortiGate one-arm sniffer or mirrored ingress path to inspect switch traffic where permitted.
  5. Verify mirror connection, FortiGate sniffing interface, capture expression, expected VLAN tags and packet direction.

Explanation

Correct Answers

D:

Use a supported FortiGate one-arm sniffer or mirrored ingress path to inspect switch traffic where permitted. Sniffer placement determines visibility; absence of a packet at one observation point does not prove no packet existed elsewhere. Verify the action with: Verify mirror connection, FortiGate sniffing interface, capture expression, expected VLAN tags and packet direction. This is the configuration or remediation half of the requested TWO-step pair.

E:

Verify mirror connection, FortiGate sniffing interface, capture expression, expected VLAN tags and packet direction. Sniffer placement determines visibility; absence of a packet at one observation point does not prove no packet existed elsewhere. The paired action is: Use a supported FortiGate one-arm sniffer or mirrored ingress path to inspect switch traffic where permitted. This is the diagnostic or verification half of the requested TWO-step pair.

Incorrect Answers

A:

Review frame error type, CRC/FCS, traffic rates, drops, operational speed, port description and sampled timestamps. This step concerns Managed switch port statistics and counter analysis and is not part of the required paired solution. The correct action and evidence are: Use a supported FortiGate one-arm sniffer or mirrored ingress path to inspect switch traffic where permitted. Together with: Verify mirror connection, FortiGate sniffing interface, capture expression, expected VLAN tags and packet direction.

B:

Investigate managed switch offline or configuration mismatch after firmware upgrade or controller resynchronization using both endpoints. This step concerns FortiLink synchronization and upgrade troubleshooting and is not part of the required paired solution. The correct action and evidence are: Use a supported FortiGate one-arm sniffer or mirrored ingress path to inspect switch traffic where permitted. Together with: Verify mirror connection, FortiGate sniffing interface, capture expression, expected VLAN tags and packet direction.

C:

The intended VLAN survives a switch restart without unexpected controller overwrite or unauthorized local change. This step concerns VLAN configuration persistence and drift control and is not part of the required paired solution. The correct action and evidence are: Use a supported FortiGate one-arm sniffer or mirrored ingress path to inspect switch traffic where permitted. Together with: Verify mirror connection, FortiGate sniffing interface, capture expression, expected VLAN tags and packet direction.

Question 464

A user authenticates successfully but its new RADIUS ACL never appears in switch policy state. Which TWO complementary steps identify the appropriate FortiSwitch response AND the evidence needed to verify it? Select TWO.

  1. Inspect frame-rate counters by class, threshold configuration, affected VLANs and protocol health under controlled load.
  2. Verify dynamic ACL assignment from RADIUS after successful 802.1X and account for platform rule and IPv4 support constraints.
  3. The impacted client can communicate on the permitted VLAN while unrelated tenant or guest VLANs remain separated.
  4. Verify that supported CoA or dynamic user security profiles are enforced on authenticated sessions under the deployed topology.
  5. Inspect RADIUS Filter-Id or downloadable ACL attribute, authenticated session state, installed hardware entries and ACL counters.

Explanation

Correct Answers

B:

Verify dynamic ACL assignment from RADIUS after successful 802.1X and account for platform rule and IPv4 support constraints. DACLs install after successful authorization and documented release limits apply; a RADIUS response alone is not proof of forwarding enforcement. Verify the action with: Inspect RADIUS Filter-Id or downloadable ACL attribute, authenticated session state, installed hardware entries and ACL counters. This is the configuration or remediation half of the requested TWO-step pair.

E:

Inspect RADIUS Filter-Id or downloadable ACL attribute, authenticated session state, installed hardware entries and ACL counters. DACLs install after successful authorization and documented release limits apply; a RADIUS response alone is not proof of forwarding enforcement. The paired action is: Verify dynamic ACL assignment from RADIUS after successful 802.1X and account for platform rule and IPv4 support constraints. This is the diagnostic or verification half of the requested TWO-step pair.

Incorrect Answers

A:

Inspect frame-rate counters by class, threshold configuration, affected VLANs and protocol health under controlled load. This step concerns Storm-control thresholds and broadcast containment and is not part of the required paired solution. The correct action and evidence are: Verify dynamic ACL assignment from RADIUS after successful 802.1X and account for platform rule and IPv4 support constraints. Together with: Inspect RADIUS Filter-Id or downloadable ACL attribute, authenticated session state, installed hardware entries and ACL counters.

C:

The impacted client can communicate on the permitted VLAN while unrelated tenant or guest VLANs remain separated. This step concerns VLAN access isolation and troubleshooting of membership and is not part of the required paired solution. The correct action and evidence are: Verify dynamic ACL assignment from RADIUS after successful 802.1X and account for platform rule and IPv4 support constraints. Together with: Inspect RADIUS Filter-Id or downloadable ACL attribute, authenticated session state, installed hardware entries and ACL counters.

D:

Verify that supported CoA or dynamic user security profiles are enforced on authenticated sessions under the deployed topology. This step concerns RADIUS change of authorization and applied session policy and is not part of the required paired solution. The correct action and evidence are: Verify dynamic ACL assignment from RADIUS after successful 802.1X and account for platform rule and IPv4 support constraints. Together with: Inspect RADIUS Filter-Id or downloadable ACL attribute, authenticated session state, installed hardware entries and ACL counters.

Question 465

The receive optical power is below specification and the team keeps modifying VLANs instead of fixing fiber attenuation. Which TWO complementary steps identify the appropriate FortiSwitch response AND the evidence needed to verify it? Select TWO.

  1. Choose supported Fortinet transceivers and link media based on switch capability, optical reach and wavelength.
  2. Switches reconnect to FortiLink and preserve approved VLAN/role configuration after the planned upgrade.
  3. Check group membership table, querier identity, IGMP report traffic, VLAN and target egress port.
  4. Use STP state and MAC move evidence to isolate one bad bridging path and change only the proven element.
  5. Inspect transceiver SKU, supported compatibility table, Tx/Rx optical power, interface alarms and cable plant type.

Explanation

Correct Answers

A:

Choose supported Fortinet transceivers and link media based on switch capability, optical reach and wavelength. Matching a mechanical optic cage is insufficient to prove optical or firmware compatibility. Verify the action with: Inspect transceiver SKU, supported compatibility table, Tx/Rx optical power, interface alarms and cable plant type. This is the configuration or remediation half of the requested TWO-step pair.

E:

Inspect transceiver SKU, supported compatibility table, Tx/Rx optical power, interface alarms and cable plant type. Matching a mechanical optic cage is insufficient to prove optical or firmware compatibility. The paired action is: Choose supported Fortinet transceivers and link media based on switch capability, optical reach and wavelength. This is the diagnostic or verification half of the requested TWO-step pair.

Incorrect Answers

B:

Switches reconnect to FortiLink and preserve approved VLAN/role configuration after the planned upgrade. This step concerns Firmware and lifecycle preparation for FortiSwitch and is not part of the required paired solution. The correct action and evidence are: Choose supported Fortinet transceivers and link media based on switch capability, optical reach and wavelength. Together with: Inspect transceiver SKU, supported compatibility table, Tx/Rx optical power, interface alarms and cable plant type.

C:

Check group membership table, querier identity, IGMP report traffic, VLAN and target egress port. This step concerns IGMP snooping and multicast receivers and is not part of the required paired solution. The correct action and evidence are: Choose supported Fortinet transceivers and link media based on switch capability, optical reach and wavelength. Together with: Inspect transceiver SKU, supported compatibility table, Tx/Rx optical power, interface alarms and cable plant type.

D:

Use STP state and MAC move evidence to isolate one bad bridging path and change only the proven element. This step concerns STP incident recovery with MAC flap evidence and is not part of the required paired solution. The correct action and evidence are: Choose supported Fortinet transceivers and link media based on switch capability, optical reach and wavelength. Together with: Inspect transceiver SKU, supported compatibility table, Tx/Rx optical power, interface alarms and cable plant type.

Question 466

A new routed VLAN exists but its SVI stays down because no participating port is operational. Which TWO complementary steps identify the appropriate FortiSwitch response AND the evidence needed to verify it? Select TWO.

  1. Set a supported default route or precise static prefix toward a reachable next hop and validate return traffic.
  2. Compare controller desired VLAN map, current switch running state, configuration synchronization and post-reboot behavior.
  3. Authorized endpoints enter only permitted VLANs while failed authentication is denied or restricted according to policy.
  4. Inspect SVI admin state, VLAN membership, address and mask, connected route, ARP and intended upstream gateway.
  5. Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context.

Explanation

Correct Answers

D:

Inspect SVI admin state, VLAN membership, address and mask, connected route, ARP and intended upstream gateway. Layer-3 SVI configuration and actual usable forwarding are separate from having a named Layer-2 VLAN. The paired action is: Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context. This is the diagnostic or verification half of the requested TWO-step pair.

E:

Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context. Layer-3 SVI configuration and actual usable forwarding are separate from having a named Layer-2 VLAN. Verify the action with: Inspect SVI admin state, VLAN membership, address and mask, connected route, ARP and intended upstream gateway. This is the configuration or remediation half of the requested TWO-step pair.

Incorrect Answers

A:

Set a supported default route or precise static prefix toward a reachable next hop and validate return traffic. This step concerns Static route and default gateway validation and is not part of the required paired solution. The correct action and evidence are: Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context. Together with: Inspect SVI admin state, VLAN membership, address and mask, connected route, ARP and intended upstream gateway.

B:

Compare controller desired VLAN map, current switch running state, configuration synchronization and post-reboot behavior. This step concerns VLAN configuration persistence and drift control and is not part of the required paired solution. The correct action and evidence are: Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context. Together with: Inspect SVI admin state, VLAN membership, address and mask, connected route, ARP and intended upstream gateway.

C:

Authorized endpoints enter only permitted VLANs while failed authentication is denied or restricted according to policy. This step concerns FortiSwitch 802.1X port-based authentication and is not part of the required paired solution. The correct action and evidence are: Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context. Together with: Inspect SVI admin state, VLAN membership, address and mask, connected route, ARP and intended upstream gateway.

Question 467

An administrator sets a static route to a next hop located behind an interface that is administratively down. Which FortiSwitch configuration or corrective action BEST addresses the requirement?

  1. Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context.
  2. Check MAC-learning table and flooding behavior before replacing a switch or changing its IP routing.
  3. Set a supported default route or precise static prefix toward a reachable next hop and validate return traffic.
  4. Choose supported FortiSwitchOS version and maintenance workflow compatible with the FortiGate version and topology.

Explanation

Correct Answer

C:

Set a supported default route or precise static prefix toward a reachable next hop and validate return traffic. A default route cannot repair local VLAN tagging or a missing neighbor resolution condition. Verify the action with: Check route table, next-hop ARP, ingress VLAN, egress interface, prefix length and return-route path.

Incorrect Answers

A:

Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context. This action is relevant to FortiSwitch SVI routing and connected routes, not the controlling requirement in this case. Layer-3 SVI configuration and actual usable forwarding are separate from having a named Layer-2 VLAN. The targeted response is: Set a supported default route or precise static prefix toward a reachable next hop and validate return traffic.

B:

Check MAC-learning table and flooding behavior before replacing a switch or changing its IP routing. This action is relevant to Layer 2 MAC-learning and forwarding decisions, not the controlling requirement in this case. An L2 switch uses MAC destination and VLAN state for forwarding; a healthy SVI is not proof a host is on the proper port. The targeted response is: Set a supported default route or precise static prefix toward a reachable next hop and validate return traffic.

D:

Choose supported FortiSwitchOS version and maintenance workflow compatible with the FortiGate version and topology. This action is relevant to Firmware and lifecycle preparation for FortiSwitch, not the controlling requirement in this case. A successful image upload does not prove switch operation or controller compatibility after reboot. The targeted response is: Set a supported default route or precise static prefix toward a reachable next hop and validate return traffic.

Question 468

A coworker plugs an unmanaged eight-port switch into a desk port and hundreds of new MACs are learned. Which FortiSwitch configuration or corrective action BEST addresses the requirement?

  1. Configure supported IEEE 802.1X port security against an approved RADIUS service with explicit guest/unauthorized behavior.
  2. Set model-supported dynamic MAC address learning limits and specific violation action on access-facing switch ports.
  3. Enable supported DHCP snooping on client VLANs and trust only known DHCP-server or relay-facing links.
  4. Assign the intended untagged native VLAN and explicitly permit tagged VLANs on an uplink; compare both ends before cutover.

Explanation

Correct Answer

B:

Set model-supported dynamic MAC address learning limits and specific violation action on access-facing switch ports. Dynamic MAC learning limits reduce accidental fan-out but should be tuned for legitimate multi-device access designs. Verify the action with: Inspect MAC table usage, configured learning limit, learned device count, port-security event and violation action.

Incorrect Answers

A:

Configure supported IEEE 802.1X port security against an approved RADIUS service with explicit guest/unauthorized behavior. This action is relevant to FortiSwitch 802.1X port-based authentication, not the controlling requirement in this case. A physical link can be up while 802.1X blocks traffic; the switch is the authenticator, not the authentication server. The targeted response is: Set model-supported dynamic MAC address learning limits and specific violation action on access-facing switch ports.

C:

Enable supported DHCP snooping on client VLANs and trust only known DHCP-server or relay-facing links. This action is relevant to DHCP snooping trust-boundary enforcement, not the controlling requirement in this case. Trusting every port defeats DHCP snooping and wrongly distrusting the server uplink may suppress all leases. The targeted response is: Set model-supported dynamic MAC address learning limits and specific violation action on access-facing switch ports.

D:

Assign the intended untagged native VLAN and explicitly permit tagged VLANs on an uplink; compare both ends before cutover. This action is relevant to FortiSwitch native VLAN versus allowed VLANs, not the controlling requirement in this case. Native VLAN handling and tagged VLAN membership are different controls; a working physical link does not validate VLAN carriage. The targeted response is: Set model-supported dynamic MAC address learning limits and specific violation action on access-facing switch ports.

Question 469

A FortiGate cluster has HA heartbeats but only the failed member owns a working FortiLink path. Which FortiSwitch configuration or corrective action BEST addresses the requirement?

  1. Define appropriate trusted ingress marking sources and classify untrusted frames before choosing egress queues.
  2. Plan FortiLink management under FortiGate HA with supported links, peer roles and deterministic failover tests.
  3. Permit shared FortiSwitch hardware across VDOMs only with verified port and feature support and explicit tenant VLAN tagging.
  4. Document tenant-specific impact, current switch state and reversal steps before changing shared FortiLink VLAN/port mappings.

Explanation

Correct Answer

B:

Plan FortiLink management under FortiGate HA with supported links, peer roles and deterministic failover tests. FortiGate HA design and FortiSwitch stacking/MCLAG are separate mechanisms; their failure paths must both be evaluated. Verify the action with: Inspect primary/secondary FortiGate roles, HA health, FortiLink uplinks, downstream switch topology and session continuity.

Incorrect Answers

A:

Define appropriate trusted ingress marking sources and classify untrusted frames before choosing egress queues. This action is relevant to QoS ingress classification and trust boundaries, not the controlling requirement in this case. A packet marking has no useful QoS effect until supported classification and scheduling map it consistently. The targeted response is: Plan FortiLink management under FortiGate HA with supported links, peer roles and deterministic failover tests.

C:

Permit shared FortiSwitch hardware across VDOMs only with verified port and feature support and explicit tenant VLAN tagging. This action is relevant to Shared port multi-VDOM policy boundaries, not the controlling requirement in this case. Shared physical ports can support some per-port controls across VDOMs, but feature support and tagging must be checked for the exact release. The targeted response is: Plan FortiLink management under FortiGate HA with supported links, peer roles and deterministic failover tests.

D:

Document tenant-specific impact, current switch state and reversal steps before changing shared FortiLink VLAN/port mappings. This action is relevant to Multi-tenant change verification and rollback, not the controlling requirement in this case. A change on shared physical transport can affect multiple VDOMs, even if each tenant's firewall policy is separate. The targeted response is: Plan FortiLink management under FortiGate HA with supported links, peer roles and deterministic failover tests.

Question 470

A phone and computer share one access port but the policy authenticates only the first observed MAC address. Which FortiSwitch configuration or corrective action BEST addresses the requirement?

  1. Assign FortiSwitch VLANs and ports to the intended FortiGate VDOM with explicit isolation and governed shared infrastructure.
  2. Enable supported DHCP snooping on client VLANs and trust only known DHCP-server or relay-facing links.
  3. Set measured storm-control thresholds for broadcast, multicast or unknown unicast as supported and validate needed discovery protocols.
  4. Use supported MAC-based access controls with narrow authorized device roles and avoid treating MAC addresses as strong identity proof.

Explanation

Correct Answer

D:

Use supported MAC-based access controls with narrow authorized device roles and avoid treating MAC addresses as strong identity proof. A MAC address can be cloned; MAC authentication must be combined with appropriate segmentation and monitoring. Verify the action with: Check learned client MAC, RADIUS MAC authentication response, access policy, fallback sequence and effective VLAN.

Incorrect Answers

A:

Assign FortiSwitch VLANs and ports to the intended FortiGate VDOM with explicit isolation and governed shared infrastructure. This action is relevant to FortiGate VDOM-based FortiSwitch tenant assignment, not the controlling requirement in this case. A VDOM creates a separate policy and routing context; it does not by itself make a shared physical switch port safe for all tenants. The targeted response is: Use supported MAC-based access controls with narrow authorized device roles and avoid treating MAC addresses as strong identity proof.

B:

Enable supported DHCP snooping on client VLANs and trust only known DHCP-server or relay-facing links. This action is relevant to DHCP snooping trust-boundary enforcement, not the controlling requirement in this case. Trusting every port defeats DHCP snooping and wrongly distrusting the server uplink may suppress all leases. The targeted response is: Use supported MAC-based access controls with narrow authorized device roles and avoid treating MAC addresses as strong identity proof.

C:

Set measured storm-control thresholds for broadcast, multicast or unknown unicast as supported and validate needed discovery protocols. This action is relevant to Storm-control thresholds and broadcast containment, not the controlling requirement in this case. Overaggressive storm control can break DHCP, ARP or group discovery even when physical links remain healthy. The targeted response is: Use supported MAC-based access controls with narrow authorized device roles and avoid treating MAC addresses as strong identity proof.

Fortinet NSE 5 - FortiSwitch 7.6 Administrator (NSE5_FSW_AD-7.6) Practice Tests