Fortinet NSE5_FSW_AD-7.6 Practice Test 45
Question 440
An unmanaged peer uses a static bundle while FortiSwitch expects active LACP negotiation. Which observable result BEST proves the intended FortiSwitch operation or security policy works?
- Spoofed ARP replies are dropped while legitimate endpoints maintain gateway ARP resolution.
- An access host receives the right subnet while only approved tagged VLANs traverse the uplink.
- The handset and attached workstation use the intended separate networks and retain their authorized access.
- Approved aggregate members forward as one bundle while nonmatching links remain excluded.
Explanation
Correct Answer
D:Approved aggregate members forward as one bundle while nonmatching links remain excluded. This is a measurable client, control-plane, or security outcome rather than a claim that configuration was entered. Passive LACP on both ends may not negotiate an active bundle, and individual green links do not prove aggregation.
Incorrect Answers
A:Spoofed ARP replies are dropped while legitimate endpoints maintain gateway ARP resolution. This result relates to Dynamic ARP inspection with DHCP snooping bindings, not the acceptance condition under test. The relevant result is: Approved aggregate members forward as one bundle while nonmatching links remain excluded.
B:An access host receives the right subnet while only approved tagged VLANs traverse the uplink. This result relates to FortiSwitch native VLAN versus allowed VLANs, not the acceptance condition under test. The relevant result is: Approved aggregate members forward as one bundle while nonmatching links remain excluded.
C:The handset and attached workstation use the intended separate networks and retain their authorized access. This result relates to Voice and data VLAN separation on shared access ports, not the acceptance condition under test. The relevant result is: Approved aggregate members forward as one bundle while nonmatching links remain excluded.
Question 441
A managed switch's controller connection stays up while a trunk change removes the voice VLAN. Which TWO complementary steps identify the appropriate FortiSwitch response AND the evidence needed to verify it? Select TWO.
- Inspect controller switch list, interface events, authentication logs, current configuration, timestamps and recent change history.
- Verify FortiLink management status and user VLAN reachability independently when a switch is authorized but clients fail.
- The user VLAN reaches the authorized gateway without being placed on an unrelated physical FortiGate interface.
- Identify FortiLink failures caused by split-interface, HA, MCLAG peer or ISL mismatches before changing unrelated ports.
- Inspect FortiLink management state, native/tagged VLANs, port membership, FortiGate interface and active firewall policy.
Explanation
Correct Answers
B:Verify FortiLink management status and user VLAN reachability independently when a switch is authorized but clients fail. FortiLink transports management and data; a successful controller heartbeat does not guarantee a user VLAN or firewall session is permitted. Verify the action with: Inspect FortiLink management state, native/tagged VLANs, port membership, FortiGate interface and active firewall policy. This is the configuration or remediation half of the requested TWO-step pair.
E:Inspect FortiLink management state, native/tagged VLANs, port membership, FortiGate interface and active firewall policy. FortiLink transports management and data; a successful controller heartbeat does not guarantee a user VLAN or firewall session is permitted. The paired action is: Verify FortiLink management status and user VLAN reachability independently when a switch is authorized but clients fail. This is the diagnostic or verification half of the requested TWO-step pair.
Incorrect Answers
A:Inspect controller switch list, interface events, authentication logs, current configuration, timestamps and recent change history. This step concerns FortiSwitch diagnostic commands and logs and is not part of the required paired solution. The correct action and evidence are: Verify FortiLink management status and user VLAN reachability independently when a switch is authorized but clients fail. Together with: Inspect FortiLink management state, native/tagged VLANs, port membership, FortiGate interface and active firewall policy.
C:The user VLAN reaches the authorized gateway without being placed on an unrelated physical FortiGate interface. This step concerns FortiGate managed FortiSwitch VLAN interface placement and is not part of the required paired solution. The correct action and evidence are: Verify FortiLink management status and user VLAN reachability independently when a switch is authorized but clients fail. Together with: Inspect FortiLink management state, native/tagged VLANs, port membership, FortiGate interface and active firewall policy.
D:Identify FortiLink failures caused by split-interface, HA, MCLAG peer or ISL mismatches before changing unrelated ports. This step concerns FortiLink HA and MCLAG topology faults and is not part of the required paired solution. The correct action and evidence are: Verify FortiLink management status and user VLAN reachability independently when a switch is authorized but clients fail. Together with: Inspect FortiLink management state, native/tagged VLANs, port membership, FortiGate interface and active firewall policy.
Question 442
A monitoring host receives no packets because the chosen mirror direction captures only ingress while the failing frames are egress. Which observable result BEST proves the intended FortiSwitch operation or security policy works?
- Switches reconnect to FortiLink and preserve approved VLAN/role configuration after the planned upgrade.
- The analyzer receives the intended copies while production forwarding remains unchanged.
- Controller and switch return to supported synchronized software and configuration with test-client services restored.
- Troubleshooting evidence is sufficient to establish the fault without exporting unnecessary private communications.
Explanation
Correct Answer
B:The analyzer receives the intended copies while production forwarding remains unchanged. A mirrored stream is passive evidence and can be incomplete if analyzer bandwidth is lower than the observed traffic.
Incorrect Answers
A:Switches reconnect to FortiLink and preserve approved VLAN/role configuration after the planned upgrade. This result relates to Firmware and lifecycle preparation for FortiSwitch, not the acceptance condition under test. The relevant result is: The analyzer receives the intended copies while production forwarding remains unchanged.
C:Controller and switch return to supported synchronized software and configuration with test-client services restored. This result relates to FortiLink synchronization and upgrade troubleshooting, not the acceptance condition under test. The relevant result is: The analyzer receives the intended copies while production forwarding remains unchanged.
D:Troubleshooting evidence is sufficient to establish the fault without exporting unnecessary private communications. This result relates to Capture and confidentiality limits in incident response, not the acceptance condition under test. The relevant result is: The analyzer receives the intended copies while production forwarding remains unchanged.
Question 443
A managed FortiSwitch learns an unauthorized DHCP server from a neighboring guest kiosk. Which diagnostic evidence should the FortiSwitch administrator examine FIRST?
- Check FortiLink parent, VLAN ID, VDOM membership, port assignment, subnet and firewall-policy path.
- Examine port binding list, packet source IP, ingress VLAN, IP-source guard counters and expected host subnet.
- Inspect DHCP server permitted list, Option 82 insertion/trust state, relay path, client bindings and lease evidence.
- Inspect ARP inspection status, DHCP snooping binding database, source MAC/IP, trusted ports and violation logs.
Explanation
Correct Answer
C:Inspect DHCP server permitted list, Option 82 insertion/trust state, relay path, client bindings and lease evidence. DHCP server allowlist and Option 82 metadata provide additional context but cannot correct a failed VLAN or missing upstream relay. The paired action is: Use documented trusted DHCP-server lists or Option 82 information where supported to enforce authorized address assignment.
Incorrect Answers
A:Check FortiLink parent, VLAN ID, VDOM membership, port assignment, subnet and firewall-policy path. These observations are applicable to FortiGate managed FortiSwitch VLAN interface placement, but would not isolate the main failure first. The decisive evidence is: Inspect DHCP server permitted list, Option 82 insertion/trust state, relay path, client bindings and lease evidence.
B:Examine port binding list, packet source IP, ingress VLAN, IP-source guard counters and expected host subnet. These observations are applicable to IPv4 source guard and binding-based packet filtering, but would not isolate the main failure first. The decisive evidence is: Inspect DHCP server permitted list, Option 82 insertion/trust state, relay path, client bindings and lease evidence.
D:Inspect ARP inspection status, DHCP snooping binding database, source MAC/IP, trusted ports and violation logs. These observations are applicable to Dynamic ARP inspection with DHCP snooping bindings, but would not isolate the main failure first. The decisive evidence is: Inspect DHCP server permitted list, Option 82 insertion/trust state, relay path, client bindings and lease evidence.
Question 444
A server sends untagged frames but its switch port expects only tagged frames and never learns the MAC in the intended VLAN. Which FortiSwitch configuration or corrective action BEST addresses the requirement?
- Use documented peer-group and downstream trunk configuration for MCLAG rather than creating ad hoc parallel Ethernet links.
- Define appropriate trusted ingress marking sources and classify untrusted frames before choosing egress queues.
- Check MAC-learning table and flooding behavior before replacing a switch or changing its IP routing.
- Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context.
Explanation
Correct Answer
C:Check MAC-learning table and flooding behavior before replacing a switch or changing its IP routing. An L2 switch uses MAC destination and VLAN state for forwarding; a healthy SVI is not proof a host is on the proper port. Verify the action with: Inspect source MAC entries by VLAN, ingress/egress port, address aging, LAG membership and broadcast counters.
Incorrect Answers
A:Use documented peer-group and downstream trunk configuration for MCLAG rather than creating ad hoc parallel Ethernet links. This action is relevant to MCLAG multichassis access redundancy, not the controlling requirement in this case. MCLAG requires peer coordination and correct downstream aggregation; it is not equivalent to connecting independent switches in parallel. The targeted response is: Check MAC-learning table and flooding behavior before replacing a switch or changing its IP routing.
B:Define appropriate trusted ingress marking sources and classify untrusted frames before choosing egress queues. This action is relevant to QoS ingress classification and trust boundaries, not the controlling requirement in this case. A packet marking has no useful QoS effect until supported classification and scheduling map it consistently. The targeted response is: Check MAC-learning table and flooding behavior before replacing a switch or changing its IP routing.
D:Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context. This action is relevant to FortiSwitch SVI routing and connected routes, not the controlling requirement in this case. Layer-3 SVI configuration and actual usable forwarding are separate from having a named Layer-2 VLAN. The targeted response is: Check MAC-learning table and flooding behavior before replacing a switch or changing its IP routing.
Question 445
A field engineer uses standalone CLI instructions on a FortiGate-managed switch and its interface settings revert. Which observable result BEST proves the intended FortiSwitch operation or security policy works?
- A planned alternate link remains blocked and takes over predictably without a broadcast storm.
- Management control and authorized user traffic work over the direct connection without confusing them.
- Every relevant VLAN converges without loops and redundant paths unblock only when needed.
- Routes and interfaces are configured at the appropriate control plane and persist after synchronization or reboot.
Explanation
Correct Answer
D:Routes and interfaces are configured at the appropriate control plane and persist after synchronization or reboot. Direct edits on a managed switch can be overridden; standalone configuration must be maintained and backed up independently.
Incorrect Answers
A:A planned alternate link remains blocked and takes over predictably without a broadcast storm. This result relates to MSTP region consistency and designated root, not the acceptance condition under test. The relevant result is: Routes and interfaces are configured at the appropriate control plane and persist after synchronization or reboot.
B:Management control and authorized user traffic work over the direct connection without confusing them. This result relates to Single FortiGate and single FortiSwitch topology, not the acceptance condition under test. The relevant result is: Routes and interfaces are configured at the appropriate control plane and persist after synchronization or reboot.
C:Every relevant VLAN converges without loops and redundant paths unblock only when needed. This result relates to RPVST and supported STP mode interoperability, not the acceptance condition under test. The relevant result is: Routes and interfaces are configured at the appropriate control plane and persist after synchronization or reboot.
Question 446
A new managed switch port allows link negotiation but users stay unauthenticated after a RADIUS server change. Which diagnostic evidence should the FortiSwitch administrator examine FIRST?
- Inspect transceiver SKU, supported compatibility table, Tx/Rx optical power, interface alarms and cable plant type.
- Inspect supplicant EAP exchange, RADIUS reachability, shared secret, port policy, authentication result and assigned access profile.
- Inspect port profile assignment, FortiGate controller policy, client role, enforcement counters and overlapping static controls.
- Inspect DHCP server permitted list, Option 82 insertion/trust state, relay path, client bindings and lease evidence.
Explanation
Correct Answer
B:Inspect supplicant EAP exchange, RADIUS reachability, shared secret, port policy, authentication result and assigned access profile. A physical link can be up while 802.1X blocks traffic; the switch is the authenticator, not the authentication server. The paired action is: Configure supported IEEE 802.1X port security against an approved RADIUS service with explicit guest/unauthorized behavior.
Incorrect Answers
A:Inspect transceiver SKU, supported compatibility table, Tx/Rx optical power, interface alarms and cable plant type. These observations are applicable to Optic compatibility and laser diagnostic evidence, but would not isolate the main failure first. The decisive evidence is: Inspect supplicant EAP exchange, RADIUS reachability, shared secret, port policy, authentication result and assigned access profile.
C:Inspect port profile assignment, FortiGate controller policy, client role, enforcement counters and overlapping static controls. These observations are applicable to FortiSwitch security profile application and precedence, but would not isolate the main failure first. The decisive evidence is: Inspect supplicant EAP exchange, RADIUS reachability, shared secret, port policy, authentication result and assigned access profile.
D:Inspect DHCP server permitted list, Option 82 insertion/trust state, relay path, client bindings and lease evidence. These observations are applicable to DHCP server allowlist and Option 82 validation, but would not isolate the main failure first. The decisive evidence is: Inspect supplicant EAP exchange, RADIUS reachability, shared secret, port policy, authentication result and assigned access profile.
Question 447
One managed port uses a stale security profile because an override did not synchronize from FortiGate. Which observable result BEST proves the intended FortiSwitch operation or security policy works?
- A session's effective access changes only when the authorization result is accepted and policy is installed on hardware.
- Legitimate clients lease addresses while rogue DHCP servers connected to untrusted access ports cannot answer.
- The impacted client can communicate on the permitted VLAN while unrelated tenant or guest VLANs remain separated.
- Port traffic follows the assigned access security requirement without arbitrary drift after controller synchronization.
Explanation
Correct Answer
D:Port traffic follows the assigned access security requirement without arbitrary drift after controller synchronization. A named security profile sitting in configuration is not proof that it was applied to the intended hardware port.
Incorrect Answers
A:A session's effective access changes only when the authorization result is accepted and policy is installed on hardware. This result relates to RADIUS change of authorization and applied session policy, not the acceptance condition under test. The relevant result is: Port traffic follows the assigned access security requirement without arbitrary drift after controller synchronization.
B:Legitimate clients lease addresses while rogue DHCP servers connected to untrusted access ports cannot answer. This result relates to DHCP snooping trust-boundary enforcement, not the acceptance condition under test. The relevant result is: Port traffic follows the assigned access security requirement without arbitrary drift after controller synchronization.
C:The impacted client can communicate on the permitted VLAN while unrelated tenant or guest VLANs remain separated. This result relates to VLAN access isolation and troubleshooting of membership, not the acceptance condition under test. The relevant result is: Port traffic follows the assigned access security requirement without arbitrary drift after controller synchronization.
Question 448
An organization attempts to push an IPv6 DACL policy even though the supported FortiSwitch release documents only IPv4 DACL support. Which diagnostic evidence should the FortiSwitch administrator examine FIRST?
- Examine LLDP transmit state, port profile, neighbor TLVs, advertised VLAN and DSCP or 802.1p settings.
- Inspect RADIUS Filter-Id or downloadable ACL attribute, authenticated session state, installed hardware entries and ACL counters.
- Check switch quarantine status, ACL/security profile, allowed remediation services, NAC event and release criteria.
- Inspect trusted-port state, Discover/Offer path, DHCP binding table, VLAN and counters for dropped offers.
Explanation
Correct Answer
B:Inspect RADIUS Filter-Id or downloadable ACL attribute, authenticated session state, installed hardware entries and ACL counters. DACLs install after successful authorization and documented release limits apply; a RADIUS response alone is not proof of forwarding enforcement. The paired action is: Verify dynamic ACL assignment from RADIUS after successful 802.1X and account for platform rule and IPv4 support constraints.
Incorrect Answers
A:Examine LLDP transmit state, port profile, neighbor TLVs, advertised VLAN and DSCP or 802.1p settings. These observations are applicable to LLDP-MED voice network policy advertisements, but would not isolate the main failure first. The decisive evidence is: Inspect RADIUS Filter-Id or downloadable ACL attribute, authenticated session state, installed hardware entries and ACL counters.
C:Check switch quarantine status, ACL/security profile, allowed remediation services, NAC event and release criteria. These observations are applicable to VLAN security policy and quarantine actions, but would not isolate the main failure first. The decisive evidence is: Inspect RADIUS Filter-Id or downloadable ACL attribute, authenticated session state, installed hardware entries and ACL counters.
D:Inspect trusted-port state, Discover/Offer path, DHCP binding table, VLAN and counters for dropped offers. These observations are applicable to DHCP snooping trust-boundary enforcement, but would not isolate the main failure first. The decisive evidence is: Inspect RADIUS Filter-Id or downloadable ACL attribute, authenticated session state, installed hardware entries and ACL counters.
Question 449
An administrator installs an ACL on the wrong ingress switch port and sees no change in affected traffic. Which observable result BEST proves the intended FortiSwitch operation or security policy works?
- Legitimate clients lease addresses while rogue DHCP servers connected to untrusted access ports cannot answer.
- The suspect device is restricted without interrupting unrelated tenants and can be restored after review.
- Only intended traffic is accepted or rejected at the switch while allowed application sessions remain functional.
- The expected known switch becomes authorized and synchronizes without accepting an unrelated device.
Explanation
Correct Answer
C:Only intended traffic is accepted or rejected at the switch while allowed application sessions remain functional. Switch ACLs and FortiGate firewall policies operate at different enforcement points; a deny on one does not prove the other applied.
Incorrect Answers
A:Legitimate clients lease addresses while rogue DHCP servers connected to untrusted access ports cannot answer. This result relates to DHCP snooping trust-boundary enforcement, not the acceptance condition under test. The relevant result is: Only intended traffic is accepted or rejected at the switch while allowed application sessions remain functional.
B:The suspect device is restricted without interrupting unrelated tenants and can be restored after review. This result relates to VLAN security policy and quarantine actions, not the acceptance condition under test. The relevant result is: Only intended traffic is accepted or rejected at the switch while allowed application sessions remain functional.
D:The expected known switch becomes authorized and synchronizes without accepting an unrelated device. This result relates to Controller authorization and pending-switch state, not the acceptance condition under test. The relevant result is: Only intended traffic is accepted or rejected at the switch while allowed application sessions remain functional.
Question 450
A FortiSwitch is asked to route between two user VLANs but the gateway addresses were configured only on hosts. Which TWO complementary steps identify the appropriate FortiSwitch response AND the evidence needed to verify it? Select TWO.
- Check both peer capabilities, auto-negotiation, administrative speed, cable quality and CRC/FCS counters.
- A moved device is traced to its current approved port and incorrect cross-connection is identified.
- Configure supported IGMP snooping and querier expectations to forward multicast only where receivers request it.
- Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context.
- Inspect SVI admin state, VLAN membership, address and mask, connected route, ARP and intended upstream gateway.
Explanation
Correct Answers
D:Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context. Layer-3 SVI configuration and actual usable forwarding are separate from having a named Layer-2 VLAN. Verify the action with: Inspect SVI admin state, VLAN membership, address and mask, connected route, ARP and intended upstream gateway. This is the configuration or remediation half of the requested TWO-step pair.
E:Inspect SVI admin state, VLAN membership, address and mask, connected route, ARP and intended upstream gateway. Layer-3 SVI configuration and actual usable forwarding are separate from having a named Layer-2 VLAN. The paired action is: Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context. This is the diagnostic or verification half of the requested TWO-step pair.
Incorrect Answers
A:Check both peer capabilities, auto-negotiation, administrative speed, cable quality and CRC/FCS counters. This step concerns Switch port speed and duplex commissioning and is not part of the required paired solution. The correct action and evidence are: Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context. Together with: Inspect SVI admin state, VLAN membership, address and mask, connected route, ARP and intended upstream gateway.
B:A moved device is traced to its current approved port and incorrect cross-connection is identified. This step concerns LLDP and MAC forwarding table extraction and is not part of the required paired solution. The correct action and evidence are: Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context. Together with: Inspect SVI admin state, VLAN membership, address and mask, connected route, ARP and intended upstream gateway.
C:Configure supported IGMP snooping and querier expectations to forward multicast only where receivers request it. This step concerns IGMP snooping and multicast receivers and is not part of the required paired solution. The correct action and evidence are: Configure supported switch virtual interfaces and routed gateway addresses with correct VLAN, subnet and management context. Together with: Inspect SVI admin state, VLAN membership, address and mask, connected route, ARP and intended upstream gateway.