Cisco 500-220 Practice Test 26
Question 250
A Cisco Meraki deployment engineer must choose a safe configuration decision and one validating observation. A branch wants voice calls to remain usable when nightly backups fill the primary ISP uplink. Which TWO steps together provide a targeted response with objective verification? Select TWO answers.
- Compare edge access policy, RADIUS response, assigned VLAN and MX permitted subnet flow.
- Check SVI addressing, routing state, next hops and representative inter-VLAN traffic.
- Compare the Dashboard configured syslog destination, network reachability and a uniquely triggered sample event.
- Set per-uplink bandwidth assumptions and measured traffic shaping policies to protect critical classes from congestion.
- Compare configured WAN bandwidth, usage peaks, rule matches and quality metrics during a controlled load test.
Explanation
Correct Answers
D:The targeted next step is: Set per-uplink bandwidth assumptions and measured traffic shaping policies to protect critical classes from congestion. The technical reason is: Traffic shaping can prioritize or constrain matching traffic; it does not increase the physical capacity of a saturated uplink. A successful verification would use: Compare configured WAN bandwidth, usage peaks, rule matches and quality metrics during a controlled load test.
E:The discriminating evidence is: Compare configured WAN bandwidth, usage peaks, rule matches and quality metrics during a controlled load test.
Incorrect Answers
A:That evidence is relevant to the distinct Meraki subject of MX access policies and switch-side authentication boundary, not the specific Dual uplink bandwidth and application shaping design requirement.
B:That evidence is relevant to the distinct Meraki subject of MS switch routing interface and L3 reachability, not the specific Dual uplink bandwidth and application shaping design requirement.
C:That evidence is relevant to the distinct Meraki subject of Syslog event forwarding and remote collector reachability, not the specific Dual uplink bandwidth and application shaping design requirement.
Question 251
A Cisco Meraki deployment engineer investigates this operational case: A two-uplink site has different service capacities but its shaping model assumes equal bandwidth in both directions. What is the most appropriate FIRST action to address the stated requirement? Select ONE best answer.
- Set per-uplink bandwidth assumptions and measured traffic shaping policies to protect critical classes from congestion.
- Use policy-based SD-WAN flow preferences tied to a known application or destination and verify the actual selected uplink.
- Design voice prioritization consistently on access ports, switches and WAN shaping instead of setting one isolated queue.
- Audit claimed hardware and license entitlement when an RMA device is swapped instead of creating a duplicate charge by assumption.
Explanation
Correct Answer
A:The targeted next step is: Set per-uplink bandwidth assumptions and measured traffic shaping policies to protect critical classes from congestion.
Incorrect Answers
B:That action is relevant to the distinct Meraki subject of Flow preferences and VPN path selection policy, not the specific Dual uplink bandwidth and application shaping design requirement. For this scenario, the proper response is: Set per-uplink bandwidth assumptions and measured traffic shaping policies to protect critical classes from congestion. Verify it through: Compare configured WAN bandwidth, usage peaks, rule matches and quality metrics during a controlled load test.
C:That action is relevant to the distinct Meraki subject of End-to-end QoS trust and voice policy, not the specific Dual uplink bandwidth and application shaping design requirement.
D:That action is relevant to the distinct Meraki subject of Licensing entitlement after hardware replacement, not the specific Dual uplink bandwidth and application shaping design requirement.
Question 252
A peer reviewer evaluates the following Meraki case. A two-uplink site has different service capacities but its shaping model assumes equal bandwidth in both directions. The proposed action is: Set per-uplink bandwidth assumptions and measured traffic shaping policies to protect critical classes from congestion. Which technical principle BEST supports this decision? Select ONE best answer.
- A stack or redundant pair may have different upgrade sequencing behavior by model and firmware; a single green Dashboard tile is not sufficient validation.
- Traffic shaping can prioritize or constrain matching traffic; it does not increase the physical capacity of a saturated uplink.
- Cloud-managed hardware requires a working management path to its regional Dashboard services; unrelated user-plane reachability is not proof of successful check-in.
- Meraki MX path choice can respond to flow preferences and measured link conditions, but correct match criteria and path health are essential.
Explanation
Correct Answer
B:Traffic shaping can prioritize or constrain matching traffic; it does not increase the physical capacity of a saturated uplink. In this situation (A two-uplink site has different service capacities but its shaping model assumes equal bandwidth in both directions.), it justifies the action: Set per-uplink bandwidth assumptions and measured traffic shaping policies to protect critical classes from congestion.
Incorrect Answers
A:That principle is relevant to the distinct Meraki subject of MS firmware and switch stack sequencing, not the specific Dual uplink bandwidth and application shaping design requirement.
C:That principle is relevant to the distinct Meraki subject of Meraki device check-in requirements and upstream firewall rules, not the specific Dual uplink bandwidth and application shaping design requirement.
D:That principle is relevant to the distinct Meraki subject of Flow preferences and VPN path selection policy, not the specific Dual uplink bandwidth and application shaping design requirement.
Question 253
A Meraki support engineer must distinguish facts from assumptions. A two-uplink site has different service capacities but its shaping model assumes equal bandwidth in both directions. Which diagnostic observation MOST DIRECTLY verifies the problem or requirement? Select ONE best answer.
- Review action-batch status, failed operations, resulting template bindings and a sample target configuration.
- Compare remote VPN route tables, local VLAN VPN participation and site address inventory.
- Compare configured WAN bandwidth, usage peaks, rule matches and quality metrics during a controlled load test.
- Inspect traffic shaping rules, application classification, uplink performance and a sampled client flow.
Explanation
Correct Answer
C:The discriminating evidence is: Compare configured WAN bandwidth, usage peaks, rule matches and quality metrics during a controlled load test. Expected result: Priority applications maintain their acceptable response while lower-priority traffic respects agreed limits.
Incorrect Answers
A:That evidence is relevant to the distinct Meraki subject of Action batches and template-based API efficiency, not the specific Dual uplink bandwidth and application shaping design requirement.
B:That evidence is relevant to the distinct Meraki subject of Auto VPN subnet advertisement and overlap, not the specific Dual uplink bandwidth and application shaping design requirement.
D:That evidence is relevant to the distinct Meraki subject of Flow preferences and VPN path selection policy, not the specific Dual uplink bandwidth and application shaping design requirement.
Question 254
An implementation lead needs a measurable acceptance criterion for a Meraki change. A two-uplink site has different service capacities but its shaping model assumes equal bandwidth in both directions. The proposed validation is: Compare configured WAN bandwidth, usage peaks, rule matches and quality metrics during a controlled load test. Which result BEST demonstrates that the intended requirement is satisfied? Select ONE best answer.
- The critical application selects the appropriate healthy uplink without indiscriminately throttling all users.
- The critical service changes to an acceptable path when its measured SLA is violated rather than waiting for full outage.
- Priority applications maintain their acceptable response while lower-priority traffic respects agreed limits.
- Real rogue devices are investigated while legitimate neighboring wireless networks are not disrupted without evidence.
Explanation
Correct Answer
C:The acceptance criterion is: Priority applications maintain their acceptable response while lower-priority traffic respects agreed limits. Verify it using: Compare configured WAN bandwidth, usage peaks, rule matches and quality metrics during a controlled load test.
Incorrect Answers
A:That outcome is relevant to the distinct Meraki subject of MX SD-WAN traffic preferences and shaping, not the specific Dual uplink bandwidth and application shaping design requirement.
B:That outcome is relevant to the distinct Meraki subject of Brownout versus hard WAN link-down detection, not the specific Dual uplink bandwidth and application shaping design requirement. For this scenario, the proper response is: Set per-uplink bandwidth assumptions and measured traffic shaping policies to protect critical classes from congestion. Verify it through: Compare configured WAN bandwidth, usage peaks, rule matches and quality metrics during a controlled load test.
D:That outcome is relevant to the distinct Meraki subject of MR Air Marshal threat and rogue SSID monitoring, not the specific Dual uplink bandwidth and application shaping design requirement.
Question 255
A Meraki operations reviewer examines this case. A two-uplink site has different service capacities but its shaping model assumes equal bandwidth in both directions. Which assumption is the MOST DIRECTLY relevant unsafe or technically wrong shortcut to reject here? Select ONE best answer.
- Set a traffic shaping rule and assert it doubles the service provider's contracted bandwidth.
- Conclude that missing Wireless controls prove an MX firmware defect when the network contains only a security appliance.
- Specify an MV camera as a substitute for a WAN firewall because both can be viewed in Dashboard.
- Assume a global WAN preference overrides all individual application flow policies under every condition.
Explanation
Correct Answer
A:It conflicts with the relevant behavior: Traffic shaping can prioritize or constrain matching traffic; it does not increase the physical capacity of a saturated uplink.
Incorrect Answers
B:That proposal is unsafe in its own context (the separate topic of Combined networks and device role visibility), but it is not the shortcut tied most directly to this incident. The case-specific fault to reject concerns Dual uplink bandwidth and application shaping design: Set a traffic shaping rule and assert it doubles the service provider's contracted bandwidth.
C:That proposal is unsafe in its own context (the separate topic of Product family capabilities and integrated Dashboard view), but it is not the shortcut tied most directly to this incident. The case-specific fault to reject concerns Dual uplink bandwidth and application shaping design: Set a traffic shaping rule and assert it doubles the service provider's contracted bandwidth.
D:That proposal is unsafe in its own context (the separate topic of Flow preferences and VPN path selection policy), but it is not the shortcut tied most directly to this incident. The case-specific fault to reject concerns Dual uplink bandwidth and application shaping design: Set a traffic shaping rule and assert it doubles the service provider's contracted bandwidth.
Question 256
A Cisco Meraki deployment engineer investigates this operational case: An internal core router learns no new office VLANs after the MX LAN routing relationship was changed. What is the most appropriate FIRST action to address the stated requirement? Select ONE best answer.
- Choose an appropriate supported route exchange and validate OSPF neighbor topology rather than inventing static routes for every subnet.
- Design voice prioritization consistently on access ports, switches and WAN shaping instead of setting one isolated queue.
- Verify both forward and return paths between Auto VPN sites and cloud workloads rather than checking only IKE state.
- Design separate guest, employee and IoT VLANs with deliberate inter-VLAN routing and firewall rules.
Explanation
Correct Answer
A:The targeted next step is: Choose an appropriate supported route exchange and validate OSPF neighbor topology rather than inventing static routes for every subnet. The technical reason is: Dynamic routing relies on consistent interfaces, adjacency and advertisement policy; the presence of an MX does not imply automatic OSPF peering everywhere.
Incorrect Answers
B:That action is relevant to the distinct Meraki subject of End-to-end QoS trust and voice policy, not the specific OSPF LAN exchange and MX routing design requirement.
C:That action is relevant to the distinct Meraki subject of vMX traffic symmetry and cloud return routing, not the specific OSPF LAN exchange and MX routing design requirement.
D:That action is relevant to the distinct Meraki subject of Network segmentation with VLANs and routed boundaries, not the specific OSPF LAN exchange and MX routing design requirement. For this scenario, the proper response is: Choose an appropriate supported route exchange and validate OSPF neighbor topology rather than inventing static routes for every subnet.
Question 257
A peer reviewer evaluates the following Meraki case. An internal core router learns no new office VLANs after the MX LAN routing relationship was changed. The proposed action is: Choose an appropriate supported route exchange and validate OSPF neighbor topology rather than inventing static routes for every subnet. Which technical principle BEST supports this decision? Select ONE best answer.
- L3/L7 firewall and threat inspection may block different stages of a session; port reachability does not guarantee application permission.
- Loss of cloud management and loss of local forwarding are different faults; local data can narrow the affected plane.
- Dynamic routing relies on consistent interfaces, adjacency and advertisement policy; the presence of an MX does not imply automatic OSPF peering everywhere.
- A static route pointing to an unreachable next hop cannot repair a missing layer-2 or layer-3 path; prefix selection determines eligible matches.
Explanation
Correct Answer
C:Dynamic routing relies on consistent interfaces, adjacency and advertisement policy; the presence of an MX does not imply automatic OSPF peering everywhere. In this situation (An internal core router learns no new office VLANs after the MX LAN routing relationship was changed.), it justifies the action: Choose an appropriate supported route exchange and validate OSPF neighbor topology rather than inventing static routes for every subnet.
Incorrect Answers
A:That principle is relevant to the distinct Meraki subject of MX layer three and layer seven security filtering, not the specific OSPF LAN exchange and MX routing design requirement.
B:That principle is relevant to the distinct Meraki subject of Device local status page during cloud management loss, not the specific OSPF LAN exchange and MX routing design requirement.
D:Verify it through: Review supported platform mode, routing configuration, neighbor status and learned prefixes in the designated topology.
Question 258
A Meraki support engineer must distinguish facts from assumptions. An internal core router learns no new office VLANs after the MX LAN routing relationship was changed. Which diagnostic observation MOST DIRECTLY verifies the problem or requirement? Select ONE best answer.
- Correlate client IP, destination, service, matched MX rule and relevant threat or content event in Dashboard.
- Test a specific client flow against MR SSID policy, VLAN assignment and the MX security rule that applies.
- Review supported platform mode, routing configuration, neighbor status and learned prefixes in the designated topology.
- Compare destination prefix, next-hop connectivity, route table and return path for a chosen test IP.
Explanation
Correct Answer
C:The discriminating evidence is: Review supported platform mode, routing configuration, neighbor status and learned prefixes in the designated topology. Expected result: Branch and datacenter routers exchange only expected internal routes with controlled convergence.
Incorrect Answers
A:That evidence is relevant to the distinct Meraki subject of MX layer three and layer seven security filtering, not the specific OSPF LAN exchange and MX routing design requirement.
B:That evidence is relevant to the distinct Meraki subject of Security policy design across MX firewall and MR WLAN, not the specific OSPF LAN exchange and MX routing design requirement.
D:That evidence is relevant to the distinct Meraki subject of Static route next hop and VPN route preference, not the specific OSPF LAN exchange and MX routing design requirement.
Question 259
An implementation lead needs a measurable acceptance criterion for a Meraki change. An internal core router learns no new office VLANs after the MX LAN routing relationship was changed. The proposed validation is: Review supported platform mode, routing configuration, neighbor status and learned prefixes in the designated topology. Which result BEST demonstrates that the intended requirement is satisfied? Select ONE best answer.
- The correct branch-to-hub VPN route and security path are both confirmed without restarting unrelated peers.
- The intended guest/application restrictions are enforced without breaking unrelated corporate services.
- Branch and datacenter routers exchange only expected internal routes with controlled convergence.
- Only authorized branch prefixes appear in the upstream routing table and return traffic follows a valid path.
Explanation
Correct Answer
C:The acceptance criterion is: Branch and datacenter routers exchange only expected internal routes with controlled convergence. Verify it using: Review supported platform mode, routing configuration, neighbor status and learned prefixes in the designated topology.
Incorrect Answers
A:That outcome is relevant to the distinct Meraki subject of Auto VPN peer tunnel health and route advertisement, not the specific OSPF LAN exchange and MX routing design requirement.
B:That outcome is relevant to the distinct Meraki subject of Security policy design across MX firewall and MR WLAN, not the specific OSPF LAN exchange and MX routing design requirement.
D:That outcome is relevant to the distinct Meraki subject of BGP route exchange at VPN hub and datacenter, not the specific OSPF LAN exchange and MX routing design requirement.
Question 260
A Cisco Meraki deployment engineer must choose a safe configuration decision and one validating observation. An internal core router learns no new office VLANs after the MX LAN routing relationship was changed. Which TWO steps together provide a targeted response with objective verification? Select TWO answers.
- Choose an appropriate supported route exchange and validate OSPF neighbor topology rather than inventing static routes for every subnet.
- Inspect classification, configured rules, uplink loss/latency and a sampled flow before and after a test.
- Compare baseline application response measurements, configured thresholds and controlled warning events.
- Review supported platform mode, routing configuration, neighbor status and learned prefixes in the designated topology.
- Correlate application response time, observed path latency/loss and affected clients over the same incident interval.
Explanation
Correct Answers
A:The targeted next step is: Choose an appropriate supported route exchange and validate OSPF neighbor topology rather than inventing static routes for every subnet. The technical reason is: Dynamic routing relies on consistent interfaces, adjacency and advertisement policy; the presence of an MX does not imply automatic OSPF peering everywhere. A successful verification would use: Review supported platform mode, routing configuration, neighbor status and learned prefixes in the designated topology.
D:The discriminating evidence is: Review supported platform mode, routing configuration, neighbor status and learned prefixes in the designated topology.
Incorrect Answers
B:That evidence is relevant to the distinct Meraki subject of MX SD-WAN traffic preferences and shaping, not the specific OSPF LAN exchange and MX routing design requirement.
C:That evidence is relevant to the distinct Meraki subject of Meraki Insight application threshold and alert tuning, not the specific OSPF LAN exchange and MX routing design requirement.
E:That evidence is relevant to the distinct Meraki subject of Meraki Insight application health and WAN visibility, not the specific OSPF LAN exchange and MX routing design requirement.