Cisco 300-415 Practice Test 77
Question 760
[New branch commissioning] A deployment engineer is preparing a validated branch or regional hub configuration before acceptance. An enterprise is moving one pilot office from static hub VPNs to Cisco SD-WAN without disrupting access to unchanged legacy sites. Choose the mechanism that actually addresses the stated condition, not a merely adjacent SD-WAN feature. Which supported action best addresses this requirement?
- Prepare the supported ZTP/PnP onboarding path with approved device identity, transport connectivity, bootstrap parameters, and reachable discovery services.
- Plan supported multicast mechanisms, service-side joins and overlay replication or forwarding behavior for the exact Cisco SD-WAN version.
- Inventory existing template variables and transition to supported configuration groups or workflows after testing feature parity and rollback.
- Stage the WAN Edge with transport and service routing, validate coexistence and migration boundaries, then shift traffic in a controlled pilot.
Explanation
Correct Answer
D:WAN migration must account for both new overlay advertisements and legacy route exchange; a one-step cutover can create blackholes. Evidence for this new branch commissioning should include: Validate route tables and end-to-end flows before, during, and after cutover, including a tested rollback path.
Incorrect Answers
A:That option concerns wan edge zero-touch provisioning onboarding. WAN migration must account for both new overlay advertisements and legacy route exchange; a one-step cutover can create blackholes. That mechanism is chiefly relevant to a different wan edge zero-touch provisioning onboarding problem: A remote branch router is shipped to a site with no local SD-WAN engineer and must discover its authorized bootstrap and controller details.
B:That option concerns multicast support and routing design. WAN migration must account for both new overlay advertisements and legacy route exchange; a one-step cutover can create blackholes. That mechanism is chiefly relevant to a different multicast support and routing design problem: A manufacturing site sends one-to-many streams to remote branches and the WAN design must support the multicast routing behavior of the deployed release.
C:That option concerns feature template versus configuration group migration. WAN migration must account for both new overlay advertisements and legacy route exchange; a one-step cutover can create blackholes.
Question 761
[Branch rollout regression] A network engineer is repairing a specific behavior observed after a controlled WAN Edge rollout. An enterprise is moving one pilot office from static hub VPNs to Cisco SD-WAN without disrupting access to unchanged legacy sites. The fix must preserve unrelated security, transport and service-VPN behavior and be confirmed by observable evidence. Which supported action best addresses this requirement?
- Stage the WAN Edge with transport and service routing, validate coexistence and migration boundaries, then shift traffic in a controlled pilot.
- Plan supported multicast mechanisms, service-side joins and overlay replication or forwarding behavior for the exact Cisco SD-WAN version.
- Use a supported service-side EIGRP routing configuration on the applicable platform and verify controlled OMP route integration.
- Prepare the supported ZTP/PnP onboarding path with approved device identity, transport connectivity, bootstrap parameters, and reachable discovery services.
Explanation
Correct Answer
A:WAN migration must account for both new overlay advertisements and legacy route exchange; a one-step cutover can create blackholes. Evidence for this branch rollout regression should include: Validate route tables and end-to-end flows before, during, and after cutover, including a tested rollback path.
Incorrect Answers
B:That option concerns multicast support and routing design. WAN migration must account for both new overlay advertisements and legacy route exchange; a one-step cutover can create blackholes. Plan supported multicast mechanisms, service-side joins and overlay replication or forwarding behavior for the exact Cisco SD-WAN version.
C:That option concerns eigrp branch lan compatibility. WAN migration must account for both new overlay advertisements and legacy route exchange; a one-step cutover can create blackholes.
D:That option concerns wan edge zero-touch provisioning onboarding. WAN migration must account for both new overlay advertisements and legacy route exchange; a one-step cutover can create blackholes. Prepare the supported ZTP/PnP onboarding path with approved device identity, transport connectivity, bootstrap parameters, and reachable discovery services.
Question 762
[Post-migration operational investigation] The engineering recommendation is: Separate SaaS breakout path treatment from private IaaS Cloud OnRamp routing and apply policies to the appropriate traffic classes. The situation is: An operations team is reviewing an observed production overlay issue after migration from legacy WAN. A branch needs both low-latency SaaS internet egress and controlled access to private enterprise resources hosted in IaaS. The fix must preserve unrelated security, transport and service-VPN behavior and be confirmed by observable evidence. Which technical rationale best supports that recommendation?
- The underlay provides IP connectivity among overlay endpoints, while the overlay controls protected service traffic and segmentation.
- Public SaaS and private cloud workload access pose different reachability and security requirements even when both use an internet underlay.
- Transport color is part of the TLOC identity and allows policy to distinguish different transport networks and path intent.
- Colocation integration is a fabric service-delivery pattern; forwarding to service resources must be enabled by routes and policy.
Explanation
Correct Answer
B:The practical discriminator is the validation step: Test public SaaS egress and private cloud service-VPN paths independently, including destination identification and policy matches. Public SaaS and private cloud workload access pose different reachability and security requirements even when both use an internet underlay.
Incorrect Answers
A:This is a rationale for underlay and overlay path separation, under the different situation A branch advertises service routes correctly, but the ISP next-hop cannot reach the remote transport destination. Public SaaS and private cloud workload access pose different reachability and security requirements even when both use an internet underlay.
C:Transport color is part of the TLOC identity and allows policy to distinguish different transport networks and path intent. This is a rationale for transport colors identify circuits, under the different situation A branch has MPLS and public internet interfaces and operations need consistent transport identity for tunnel creation and policy. It does not justify the specific proposed mechanism for direct internet versus cloud overlay access. Public SaaS and private cloud workload access pose different reachability and security requirements even when both use an internet underlay.
D:Colocation integration is a fabric service-delivery pattern; forwarding to service resources must be enabled by routes and policy. This is a rationale for cloud onramp colocation service chaining, under the different situation A company centralizes security services in a colocation location and wants selected branch application flows routed through those services. It does not justify the specific proposed mechanism for direct internet versus cloud overlay access. Public SaaS and private cloud workload access pose different reachability and security requirements even when both use an internet underlay.
Question 763
[Branch rollout regression] The engineer detects the following failed approach: Treating multicast destination addresses as ordinary unicast OMP prefixes ignores group membership and replication requirements. The original need remains: A network engineer is repairing a specific behavior observed after a controlled WAN Edge rollout. A manufacturing site sends one-to-many streams to remote branches and the WAN design must support the multicast routing behavior of the deployed release. The fix must preserve unrelated security, transport and service-VPN behavior and be confirmed by observable evidence. What is the best controlled recovery plan?
- Instead implement this other change: Deploy a supported regional WAN Edge hub with service reachability, transport TLOCs, and route/policy design for the targeted branches. Its usual validation would be: Verify hub service prefixes, branch OMP reachability, tunnel health, and actual branch-to-hub application forwarding.
- Instead implement this other change: Use supported SD-WAN Manager configuration groups with reusable feature profiles and device-specific values where needed. Its usual validation would be: Inspect group membership, feature profile bindings, per-device values and successful deployment results across sample sites.
- Correct the design by doing the following: Plan supported multicast mechanisms, service-side joins and overlay replication or forwarding behavior for the exact Cisco SD-WAN version. Then confirm success with this specific check: Verify multicast group joins, traffic replication/arrival at intended branches, and absence of delivery at unapproved sites.
- Instead implement this other change: Establish service-VPN BGP peerings and tightly control which learned prefixes are redistributed or advertised into OMP. Its usual validation would be: Inspect BGP neighbor state and selected prefixes, OMP advertised routes and remote received routes for only intended subnets.
Explanation
Correct Answer
C:It restores the intended mechanism because Multicast support is feature- and release-dependent and requires correct service-side routing plus supported fabric distribution. This directly repairs the described failure: Treating multicast destination addresses as ordinary unicast OMP prefixes ignores group membership and replication requirements.
Incorrect Answers
A:The alternative change addresses regional hub wan edge placement where the separate requirement is Several branches require deterministic access to a regional hub for shared services, while overlay edge policy must remain centrally manageable. It does not directly repair the present failure (Treating multicast destination addresses as ordinary unicast OMP prefixes ignores group membership and replication requirements.); the needed correction is Plan supported multicast mechanisms, service-side joins and overlay replication or forwarding behavior for the exact Cisco SD-WAN version.
B:The alternative change addresses configuration groups reusable feature profiles where the separate requirement is Dozens of WAN Edges share transport settings but retain per-site IP addresses and service-VPN differences under current Manager workflows. It does not directly repair the present failure (Treating multicast destination addresses as ordinary unicast OMP prefixes ignores group membership and replication requirements.); the needed correction is Plan supported multicast mechanisms, service-side joins and overlay replication or forwarding behavior for the exact Cisco SD-WAN version.
D:It does not directly repair the present failure (Treating multicast destination addresses as ordinary unicast OMP prefixes ignores group membership and replication requirements.); the needed correction is Plan supported multicast mechanisms, service-side joins and overlay replication or forwarding behavior for the exact Cisco SD-WAN version.
Question 764
[Central policy design workshop] The engineer detects the following failed approach: Using only a local queueing rule does not prevent forbidden service prefixes from being distributed across the overlay. The original need remains: A design team is specifying policy intent for distinct sites, transports and application classes. A compliance requirement says only a subset of branch prefixes may be advertised to a specified regional group of SD-WAN sites. Choose the mechanism that actually addresses the stated condition, not a merely adjacent SD-WAN feature. What is the best controlled recovery plan?
- Instead implement this other change: Constrain centralized policy attachment to the correct site list and test membership before rollout. Its usual validation would be: Inspect the active policy definition and site-list entries, then compare route outcomes at pilot and non-pilot branches.
- Instead implement this other change: Order supported data-policy sequences from specific intended matches toward an appropriate default and validate effective evaluation behavior. Its usual validation would be: Verify per-sequence counters and a controlled voice-flow trace, then confirm the specific rule acts on matching packets.
- Instead implement this other change: Implement policy-based regional internet breakout with explicit route, service and security considerations for the selected sites. Its usual validation would be: Confirm matching traffic reaches the approved regional exit while unrelated local enterprise traffic remains correctly routed.
- Correct the design by doing the following: Create and apply a centralized control policy matching permitted site and prefix sets, then confirm its OMP advertisement results. Then confirm success with this specific check: Inspect received and advertised OMP routes at Controllers and affected edges; verify excluded prefixes are absent where prohibited.
Explanation
Correct Answer
D:It restores the intended mechanism because Centralized control policy influences the routes accepted and distributed by Controllers, controlling overlay reachability without carrying user payloads.
Incorrect Answers
A:The alternative change addresses site-list targeting in centralized policy where the separate requirement is Only ten pilot branches should receive a new route distribution behavior, but a policy change affects the whole regional fabric. It does not directly repair the present failure (Using only a local queueing rule does not prevent forbidden service prefixes from being distributed across the overlay.); the needed correction is Create and apply a centralized control policy matching permitted site and prefix sets, then confirm its OMP advertisement results.
B:The alternative change addresses data-policy sequence ordering where the separate requirement is Two overlapping application match statements exist and a broad catch-all is processed before the narrow voice policy.
C:It does not directly repair the present failure (Using only a local queueing rule does not prevent forbidden service prefixes from being distributed across the overlay.); the needed correction is Create and apply a centralized control policy matching permitted site and prefix sets, then confirm its OMP advertisement results.
Question 765
[SD-WAN architecture design review] The proposed action is: Use BFD session health and measured loss, latency, and jitter for the relevant overlay tunnels to evaluate path condition. The requirement is: An enterprise WAN design board is assessing a planned topology before deploying new branches. An internet circuit remains physically up yet becomes lossy, and the service team needs tunnel-level evidence of forwarding quality. Choose the mechanism that actually addresses the stated condition, not a merely adjacent SD-WAN feature. Which observation provides the most direct success evidence?
- Inspect the per-tunnel BFD state and performance metrics and correlate them with the affected application path.
- Confirm the operational IPsec transport tunnel and a successful service-side traffic flow over the expected overlay path.
- Benchmark representative encrypted traffic and verify CPU utilization, tunnel state, and policy feature support under load.
- Compare control connections, OMP learned routes, TLOC state, BFD, and a traced application packet against the intended VPN path.
Explanation
Correct Answer
A:Bidirectional Forwarding Detection on SD-WAN data tunnels identifies reachability and supplies performance measurements that policies can consume. This checks whether Use BFD session health and measured loss, latency, and jitter for the relevant overlay tunnels to evaluate path condition. achieved the target state rather than merely confirming a related configuration exists.
Incorrect Answers
B:Those observations would be useful for data-plane encrypted overlay forwarding, where the separate issue is: The control plane displays a valid remote route, and the security reviewer must establish how branch application traffic is protected in transit. The needed observation is: Inspect the per-tunnel BFD state and performance metrics and correlate them with the affected application path.
C:Those observations would be useful for wan edge crypto and throughput sizing, where the separate issue is: A site with encrypted overlay links must sustain its target traffic level even when inspection and multiple transports are enabled. They do not directly establish the present bfd overlay tunnel health result.
D:Those observations would be useful for control-plane versus data-plane failure isolation, where the separate issue is: An engineer sees all controllers connected but users report a broken site-to-site application path after a circuit change. They do not directly establish the present bfd overlay tunnel health result.
Question 766
[Security and QoS acceptance test] The proposed action is: Apply supported URL-filtering categories and exceptions within the applicable WAN Edge security policy. The requirement is: A network-security engineering team is evaluating enforcement before changing production service flows. A branch must block approved categories of high-risk websites while keeping allowed productivity sites reachable. Choose the mechanism that actually addresses the stated condition, not a merely adjacent SD-WAN feature. Which observation provides the most direct success evidence?
- Inspect SGT classification and propagation and verify expected permits and denies across allowed enforcement points.
- Test allowed and blocked URL categories and inspect policy hit events without misclassifying unrelated destinations.
- Observe duplicate traffic across eligible transports and application packet delivery during selective path impairment.
- Validate IPS engine state, applicable policy, signature currency and controlled detection logs while preserving authorized application flows.
Explanation
Correct Answer
B:URL filtering evaluates web destination reputation or categories where supported; traffic forwarding or DNS name resolution alone is not a category policy. This checks whether Apply supported URL-filtering categories and exceptions within the applicable WAN Edge security policy. achieved the target state rather than merely confirming a related configuration exists.
Incorrect Answers
A:Those observations would be useful for trustsec security group policy, where the separate issue is: A segmented enterprise wants policy decisions tied to trusted group identity rather than only per-site IPv4 address lists. They do not directly establish the present url-filtering web access decisions result.
C:Those observations would be useful for packet duplication for high-value traffic, where the separate issue is: A small, latency-sensitive flow requires greater delivery resilience over two independently usable transport paths. They do not directly establish the present url-filtering web access decisions result.
D:Those observations would be useful for intrusion prevention inspection at branches, where the separate issue is: A branch security policy requires detection and prevention of exploit signatures in traffic that passes the supported security stack. They do not directly establish the present url-filtering web access decisions result.
Question 767
[New branch commissioning] A deployment engineer is preparing a validated branch or regional hub configuration before acceptance. New branch-to-branch service traffic needs an overlay tunnel that forms according to valid route/TLOC information and current fabric policy. Choose the mechanism that actually addresses the stated condition, not a merely adjacent SD-WAN feature. Which supported action best addresses this requirement?
- Use a supported service-side EIGRP routing configuration on the applicable platform and verify controlled OMP route integration.
- Configure a supported TLOC-extension arrangement on the interconnected routers and verify transport reachability and tunnel establishment.
- Verify the remote TLOC reachability, OMP route exchange and supported on-demand or dynamic tunnel behavior for the selected devices.
- Stage the WAN Edge with transport and service routing, validate coexistence and migration boundaries, then shift traffic in a controlled pilot.
Explanation
Correct Answer
C:Dynamic tunnel formation still relies on reachable transport endpoints and permitted fabric control information; a policy name alone is insufficient. Evidence for this new branch commissioning should include: Observe tunnel creation, BFD state and encrypted packet forwarding following a controlled eligible traffic flow.
Incorrect Answers
A:That option concerns eigrp branch lan compatibility. Dynamic tunnel formation still relies on reachable transport endpoints and permitted fabric control information; a policy name alone is insufficient.
B:That option concerns tloc extension across dual branch routers. Dynamic tunnel formation still relies on reachable transport endpoints and permitted fabric control information; a policy name alone is insufficient.
D:That option concerns branch migration from traditional wan. Dynamic tunnel formation still relies on reachable transport endpoints and permitted fabric control information; a policy name alone is insufficient.
Question 768
[SD-WAN architecture design review] The engineer detects the following failed approach: Trying to hairpin normal application data through Manager confuses management functions with the forwarding plane. The original need remains: An enterprise WAN design board is assessing a planned topology before deploying new branches. Operations needs one platform to push centralized configuration and review fabric health without forwarding branch application packets through that platform. Choose the mechanism that actually addresses the stated condition, not a merely adjacent SD-WAN feature. What is the best controlled recovery plan?
- Instead implement this other change: Design and validate the supported Cisco Catalyst SD-WAN Multi-Region Fabric roles and regional connectivity before enabling region-specific paths. Its usual validation would be: Check region identifiers, border connectivity, controller visibility, and the expected region-to-region forwarding paths.
- Instead implement this other change: Verify OMP adjacency with the Cisco SD-WAN Controllers and appropriate advertisement of service-side prefixes and transport locators. Its usual validation would be: Inspect OMP peers, received routes, TLOC resolution, and the installed service-VPN route at the receiving edge.
- Instead implement this other change: Use BFD session health and measured loss, latency, and jitter for the relevant overlay tunnels to evaluate path condition. Its usual validation would be: Inspect the per-tunnel BFD state and performance metrics and correlate them with the affected application path.
- Correct the design by doing the following: Use Cisco SD-WAN Manager for configuration administration, monitoring, and operational workflows, leaving user traffic to the WAN Edge data plane. Then confirm success with this specific check: Verify device inventory, successful configuration tasks, and operational telemetry in Manager while branch-to-branch packets take edge tunnels.
Explanation
Correct Answer
D:It restores the intended mechanism because SD-WAN Manager (formerly vManage) owns the management plane; data forwarding occurs on edges and control routes are coordinated separately by Controllers. This directly repairs the described failure: Trying to hairpin normal application data through Manager confuses management functions with the forwarding plane.
Incorrect Answers
A:The alternative change addresses multi-region fabric segmentation where the separate requirement is A global SD-WAN needs region-aware transport topology while retaining interregional reachability through planned border roles.
B:It does not directly repair the present failure (Trying to hairpin normal application data through Manager confuses management functions with the forwarding plane.); the needed correction is Use Cisco SD-WAN Manager for configuration administration, monitoring, and operational workflows, leaving user traffic to the WAN Edge data plane.
C:The alternative change addresses bfd overlay tunnel health where the separate requirement is An internet circuit remains physically up yet becomes lossy, and the service team needs tunnel-level evidence of forwarding quality. It does not directly repair the present failure (Trying to hairpin normal application data through Manager confuses management functions with the forwarding plane.); the needed correction is Use Cisco SD-WAN Manager for configuration administration, monitoring, and operational workflows, leaving user traffic to the WAN Edge data plane.
Question 769
[Controller connectivity incident] The engineer detects the following failed approach: Assuming the WAN Edge data plane automatically restores a failed Manager instance leaves management operations unprotected. The original need remains: An on-call engineer must restore the exact controller or fabric identity behavior without changing unrelated service routes. The Manager service lives in one physical facility and operations needs administration access during a site-level outage. The fix must preserve unrelated security, transport and service-VPN behavior and be confirmed by observable evidence. What is the best controlled recovery plan?
- Correct the design by doing the following: Design supported SD-WAN Manager high-availability or recovery across appropriate failure domains and practice administrative restoration. Then confirm success with this specific check: Simulate management-site loss and validate administrator access, inventory and configuration recovery from the designated standby arrangement.
- Instead implement this other change: Import and synchronize the correctly identified WAN Edge into the authorized device inventory and confirm ownership approval. Its usual validation would be: Review the device's chassis/serial identity in the Manager authorized list and observe successful controller authorization.
- Instead implement this other change: Design multiple appropriately placed Cisco SD-WAN Controllers with reachability, consistent policy, and tested failover. Its usual validation would be: Stop one controller in a controlled test and confirm surviving control peers and continued advertised OMP reachability.
- Instead implement this other change: Inspect control-connection diagnostics and Controller identity/reachability before changing service-VPN routing policies. Its usual validation would be: Use supported show sdwan control connections/local-properties and Controller logs to isolate reachability, identity or certificate faults.
Explanation
Correct Answer
A:It restores the intended mechanism because Manager availability depends on the selected deployment and recovery architecture rather than just the number of edge tunnels. This directly repairs the described failure: Assuming the WAN Edge data plane automatically restores a failed Manager instance leaves management operations unprotected.
Incorrect Answers
B:The alternative change addresses authorized device list onboarding where the separate requirement is A hardware edge has a valid identity certificate yet is absent from the authorized device inventory and is rejected by fabric admission. It does not directly repair the present failure (Assuming the WAN Edge data plane automatically restores a failed Manager instance leaves management operations unprotected.); the needed correction is Design supported SD-WAN Manager high-availability or recovery across appropriate failure domains and practice administrative restoration.
C:It does not directly repair the present failure (Assuming the WAN Edge data plane automatically restores a failed Manager instance leaves management operations unprotected.); the needed correction is Design supported SD-WAN Manager high-availability or recovery across appropriate failure domains and practice administrative restoration.
D:The alternative change addresses troubleshooting control peer state where the separate requirement is A WAN Edge is joined to Manager yet reports no SD-WAN Controller control adjacency and no remote OMP route updates. It does not directly repair the present failure (Assuming the WAN Edge data plane automatically restores a failed Manager instance leaves management operations unprotected.); the needed correction is Design supported SD-WAN Manager high-availability or recovery across appropriate failure domains and practice administrative restoration.
Question 770
[Application degradation investigation] An operations team is analyzing security or QoS outcomes using a representative impaired application flow. A dual-transport branch needs QoS treatment that accounts for separate overlay tunnels and variable available link capacity. The fix must preserve unrelated security, transport and service-VPN behavior and be confirmed by observable evidence. Which design or operational mistake would most directly defeat the intended outcome?
- Enabling decryption indiscriminately without certificate trust or exemption policy can break applications and violate privacy requirements.
- Applying a single fixed aggregate QoS assumption to a variable collection of tunnels can starve priority traffic after failover.
- Marking packets without an egress queue policy may not protect the voice class when the link saturates.
- Blocking one hard-coded IP address as a category strategy can miss other domains or affect innocent sites sharing that IP.
Explanation
Correct Answer
B:This mistake undermines the intended adaptive and per-tunnel qos requirement. Applying a single fixed aggregate QoS assumption to a variable collection of tunnels can starve priority traffic after failover.
Incorrect Answers
A:That failure mode is primarily about tls decryption and proxy policy constraints instead of this required adaptive and per-tunnel qos treatment.
C:That failure mode is primarily about qos scheduling for real-time traffic instead of this required adaptive and per-tunnel qos treatment. Its relevance would depend on Interactive voice frames compete with bulk backups on a constrained WAN circuit and need controlled service under congestion.
D:That failure mode is primarily about url-filtering web access decisions instead of this required adaptive and per-tunnel qos treatment. Its relevance would depend on A branch must block approved categories of high-risk websites while keeping allowed productivity sites reachable.