Cisco 300-415 Practice Test 19
Question 180
[Post-migration operational investigation] An operations team is reviewing an observed production overlay issue after migration from legacy WAN. A business-critical office has two ISPs but only one router, creating a remaining device failure domain. The fix must preserve unrelated security, transport and service-VPN behavior and be confirmed by observable evidence. Which design or operational mistake would most directly defeat the intended outcome?
- Relying on only underlay routing to exchange service-VPN site prefixes bypasses the OMP overlay control function.
- Closing the incident because control peers are up ignores a possible data-plane fault.
- Choosing hardware solely from physical interface bandwidth can undersize the encrypted data plane.
- Calling dual circuits full edge redundancy overlooks the single device that terminates both transports.
Explanation
Correct Answer
D:This mistake undermines the intended wan edge redundancy at a branch requirement. Calling dual circuits full edge redundancy overlooks the single device that terminates both transports.
Incorrect Answers
A:That failure mode is primarily about sd-wan controller omp route distribution instead of this required wan edge redundancy at a branch treatment.
B:That failure mode is primarily about control-plane versus data-plane failure isolation instead of this required wan edge redundancy at a branch treatment.
C:That failure mode is primarily about wan edge crypto and throughput sizing instead of this required wan edge redundancy at a branch treatment.
Question 181
[Central policy design workshop] The proposed action is: Define application or data-policy path eligibility and preference using the correct TLOC transport color lists and failover behavior. The requirement is: A design team is specifying policy intent for distinct sites, transports and application classes. The design prefers private MPLS for ERP while allowing public internet only if the private tunnel becomes unusable. Choose the mechanism that actually addresses the stated condition, not a merely adjacent SD-WAN feature. Which observation provides the most direct success evidence?
- Test both normal ERP steering over MPLS and automatic selection of permitted internet backup after MPLS BFD failure.
- Trace matched finance traffic and unmatched traffic, check active edge policy state, and verify intended forwarding outcomes.
- Compare packet handling on the target branch with a control branch and inspect the active local data policy.
- Observe traffic classification counters and selected paths for the intended app versus unrelated applications.
Explanation
Correct Answer
A:Color-based path constraints translate transport intent into overlay forwarding rules when associated TLOCs are active. Test both normal ERP steering over MPLS and automatic selection of permitted internet backup after MPLS BFD failure.
Incorrect Answers
B:Those observations would be useful for centralized data-policy traffic steering, where the separate issue is: An SD-WAN site must steer only finance application flows through a specified service path while all other business traffic uses defaults. They do not directly establish the present transport color eligibility for application policies result.
C:Those observations would be useful for localized data-policy enforcement, where the separate issue is: An isolated branch has a site-specific packet handling rule that should not be applied throughout the SD-WAN enterprise. They do not directly establish the present transport color eligibility for application policies result.
D:Those observations would be useful for aar application classification accuracy, where the separate issue is: A network team built an SLA steering rule, but the intended video application never appears in its policy matches. They do not directly establish the present transport color eligibility for application policies result.
Question 182
[New branch commissioning] The proposed action is: Use a supported CLI add-on profile within the appropriate configuration workflow, validating command compatibility and precedence. The requirement is: A deployment engineer is preparing a validated branch or regional hub configuration before acceptance. A current feature profile covers almost every site option but the approved design requires an additional supported CLI command not exposed in that profile. Choose the mechanism that actually addresses the stated condition, not a merely adjacent SD-WAN feature. Which observation provides the most direct success evidence?
- Observe device discovery, certificate authentication, assigned configuration, controller peering, and overlay tunnel formation after power-up.
- Preview resulting device configuration and confirm the additional command applies without conflicting with profile-managed settings.
- Verify boot-time system settings, controller reachability, accepted identity, and successful enrollment using the bootstrap path.
- Observe tunnel creation, BFD state and encrypted packet forwarding following a controlled eligible traffic flow.
Explanation
Correct Answer
B:A CLI add-on can extend profile-managed devices with required supported commands, subject to release and configuration restrictions. This checks whether Use a supported CLI add-on profile within the appropriate configuration workflow, validating command compatibility and precedence. achieved the target state rather than merely confirming a related configuration exists.
Incorrect Answers
A:Those observations would be useful for wan edge zero-touch provisioning onboarding, where the separate issue is: A remote branch router is shipped to a site with no local SD-WAN engineer and must discover its authorized bootstrap and controller details. They do not directly establish the present cli add-on for unsupported profile element result.
C:Those observations would be useful for offline bootstrap for restricted wan edges, where the separate issue is: A site cannot access the normal public onboarding service during commissioning and must join a privately hosted SD-WAN fabric. They do not directly establish the present cli add-on for unsupported profile element result.
D:Those observations would be useful for dynamic tunnel establishment under policy, where the separate issue is: New branch-to-branch service traffic needs an overlay tunnel that forms according to valid route/TLOC information and current fabric policy. They do not directly establish the present cli add-on for unsupported profile element result.
Question 183
[Controller deployment acceptance] A platform team is validating control component readiness during staged site onboarding. A branch behind a carrier NAT reaches the internet but never discovers its fabric controllers during first activation. Choose the mechanism that actually addresses the stated condition, not a merely adjacent SD-WAN feature. Which design or operational mistake would most directly defeat the intended outcome?
- Disabling trust validation or adding data-plane routes does not repair the root cause of an invalid device certificate.
- Reissuing certificates without fixing a drifting system clock can reproduce the same authentication failure.
- Assuming a successful ping to a public website proves Validator discovery and secure admission is a false positive.
- Declaring availability because two VMs exist on one failed physical host masks the shared dependency.
Explanation
Correct Answer
C:Assuming a successful ping to a public website proves Validator discovery and secure admission is a false positive.
Incorrect Answers
A:That failure mode is primarily about certificate validity and chain of trust instead of this required validator discovery and nat traversal treatment.
B:That failure mode is primarily about control session clock skew instead of this required validator discovery and nat traversal treatment.
D:That failure mode is primarily about disaster-recovery control-site isolation instead of this required validator discovery and nat traversal treatment. Declaring availability because two VMs exist on one failed physical host masks the shared dependency.
Question 184
[Branch rollout regression] A network engineer is repairing a specific behavior observed after a controlled WAN Edge rollout. A legacy enterprise distribution network uses EIGRP while a new Cisco IOS XE SD-WAN Edge must learn its routes without replacing the LAN protocol. The fix must preserve unrelated security, transport and service-VPN behavior and be confirmed by observable evidence. Which design or operational mistake would most directly defeat the intended outcome?
- Assuming a template can simply be renamed into a feature profile without conversion may break site-specific values.
- Expecting tunnels to appear without valid remote TLOC resolution or underlay IP reachability ignores the overlay prerequisites.
- A local OSPF route by itself does not guarantee that the remote WAN Edge receives the same destination through OMP.
- Assuming EIGRP neighbors automatically form across the encrypted WAN overlay can bypass the intended service-side and OMP roles.
Explanation
Correct Answer
D:The supported correction is Use a supported service-side EIGRP routing configuration on the applicable platform and verify controlled OMP route integration, and the independent evidence to seek is Check EIGRP neighbors, local route installation, selective route advertisement into OMP and remote reachability. This mistake undermines the intended eigrp branch lan compatibility requirement.
Incorrect Answers
A:That failure mode is primarily about feature template versus configuration group migration instead of this required eigrp branch lan compatibility treatment. Its relevance would depend on A deployment still uses older device/feature templates while the operations team is planning a controlled migration to modern workflows.
B:That failure mode is primarily about dynamic tunnel establishment under policy instead of this required eigrp branch lan compatibility treatment.
C:That failure mode is primarily about omp advertisement of branch lan prefixes instead of this required eigrp branch lan compatibility treatment.
Question 185
[Security and QoS acceptance test] The proposed action is: Evaluate supported forward error correction for the eligible SD-WAN data path and balance recovered loss against added overhead. The requirement is: A network-security engineering team is evaluating enforcement before changing production service flows. A real-time application suffers recoverable packet loss on a busy link but cannot tolerate repeated retransmission delay. Choose the mechanism that actually addresses the stated condition, not a merely adjacent SD-WAN feature. Which observation provides the most direct success evidence?
- Measure application loss and bandwidth overhead before and after enabling FEC under repeatable link impairment.
- Inspect per-tunnel QoS statistics and performance under changed transport conditions, including path failover.
- Exercise permitted test artifacts and validate file inspection events and enforcement without relying on live malware samples.
- Trace matching application packets through inspection and verify return-path symmetry, security logs and unaffected exempt flows.
Explanation
Correct Answer
A:FEC adds redundancy to permit recovery from some losses without retransmitting original application packets; it consumes bandwidth. This checks whether Evaluate supported forward error correction for the eligible SD-WAN data path and balance recovered loss against added overhead. achieved the target state rather than merely confirming a related configuration exists.
Incorrect Answers
B:Those observations would be useful for adaptive and per-tunnel qos, where the separate issue is: A dual-transport branch needs QoS treatment that accounts for separate overlay tunnels and variable available link capacity. They do not directly establish the present forward error correction for lossy links result.
C:Those observations would be useful for malware protection on downloaded files, where the separate issue is: The security team needs supported anti-malware inspection of eligible branch downloads and related policy evidence. They do not directly establish the present forward error correction for lossy links result.
D:Those observations would be useful for service insertion for external inspection, where the separate issue is: A regulated application must visit a regional inspection appliance before exiting the enterprise, even when normal OMP paths are shorter. They do not directly establish the present forward error correction for lossy links result.
Question 186
[New branch commissioning] The proposed action is: Prepare the supported ZTP/PnP onboarding path with approved device identity, transport connectivity, bootstrap parameters, and reachable discovery services. The requirement is: A deployment engineer is preparing a validated branch or regional hub configuration before acceptance. A remote branch router is shipped to a site with no local SD-WAN engineer and must discover its authorized bootstrap and controller details. Choose the mechanism that actually addresses the stated condition, not a merely adjacent SD-WAN feature. Which observation provides the most direct success evidence?
- Verify hub service prefixes, branch OMP reachability, tunnel health, and actual branch-to-hub application forwarding.
- Observe device discovery, certificate authentication, assigned configuration, controller peering, and overlay tunnel formation after power-up.
- Validate route tables and end-to-end flows before, during, and after cutover, including a tested rollback path.
- Verify boot-time system settings, controller reachability, accepted identity, and successful enrollment using the bootstrap path.
Explanation
Correct Answer
B:Automated onboarding works when the device is authorized and can find its initial controller; physical power and internet access alone do not prove fabric membership. Observe device discovery, certificate authentication, assigned configuration, controller peering, and overlay tunnel formation after power-up.
Incorrect Answers
A:Those observations would be useful for regional hub wan edge placement, where the separate issue is: Several branches require deterministic access to a regional hub for shared services, while overlay edge policy must remain centrally manageable. They do not directly establish the present wan edge zero-touch provisioning onboarding result.
C:Those observations would be useful for branch migration from traditional wan, where the separate issue is: An enterprise is moving one pilot office from static hub VPNs to Cisco SD-WAN without disrupting access to unchanged legacy sites. They do not directly establish the present wan edge zero-touch provisioning onboarding result.
D:Those observations would be useful for offline bootstrap for restricted wan edges, where the separate issue is: A site cannot access the normal public onboarding service during commissioning and must join a privately hosted SD-WAN fabric. They do not directly establish the present wan edge zero-touch provisioning onboarding result.
Question 187
[New branch commissioning] The engineering recommendation is: Repair VPN 0 transport routing, correct ISP next hop and proper tunnel interface configuration before attempting overlay fixes. The situation is: A deployment engineer is preparing a validated branch or regional hub configuration before acceptance. An internet-connected WAN Edge shows a configured service VPN but cannot reach the Validator IP over its underlay. Choose the mechanism that actually addresses the stated condition, not a merely adjacent SD-WAN feature. Which technical rationale best supports that recommendation?
- Configuration groups and profiles reduce drift while preserving intended per-device variables; they are not equivalent to a single identical CLI file.
- Service-side OSPF learns local site prefixes, whereas OMP distributes appropriate service routes among SD-WAN sites.
- VPN 0 carries transport-side IP connectivity; service-VPN routes do not substitute for a usable controller/peer underlay path.
- OMP distributes service prefixes in the overlay; dynamic routing in a local service VPN must be imported or advertised appropriately.
Explanation
Correct Answer
C:The practical discriminator is the validation step: Test transport VPN 0 routing and controller reachability, then inspect the control and BFD sessions after correction. VPN 0 carries transport-side IP connectivity; service-VPN routes do not substitute for a usable controller/peer underlay path.
Incorrect Answers
A:This is a rationale for configuration groups reusable feature profiles, under the different situation Dozens of WAN Edges share transport settings but retain per-site IP addresses and service-VPN differences under current Manager workflows. VPN 0 carries transport-side IP connectivity; service-VPN routes do not substitute for a usable controller/peer underlay path.
B:Service-side OSPF learns local site prefixes, whereas OMP distributes appropriate service routes among SD-WAN sites. This is a rationale for ospf service vpn adjacency, under the different situation A branch Layer 3 switch speaks OSPF to a WAN Edge, and its learned LAN routes need to participate in the SD-WAN overlay. It does not justify the specific proposed mechanism for transport vpn 0 default-route correctness. VPN 0 carries transport-side IP connectivity; service-VPN routes do not substitute for a usable controller/peer underlay path.
D:This is a rationale for omp advertisement of branch lan prefixes, under the different situation Two WAN Edge routers show established controller connections but one cannot reach the other site's advertised office subnet. VPN 0 carries transport-side IP connectivity; service-VPN routes do not substitute for a usable controller/peer underlay path.
Question 188
[Policy-change production incident] A change manager is isolating the side effect of an active policy without weakening unrelated segmentation. A compliance requirement says only a subset of branch prefixes may be advertised to a specified regional group of SD-WAN sites. The fix must preserve unrelated security, transport and service-VPN behavior and be confirmed by observable evidence. Which supported action best addresses this requirement?
- Implement policy-based regional internet breakout with explicit route, service and security considerations for the selected sites.
- Constrain centralized policy attachment to the correct site list and test membership before rollout.
- Implement a supported DIA routing and NAT/security policy for guest traffic at the branch and verify service-side matching.
- Create and apply a centralized control policy matching permitted site and prefix sets, then confirm its OMP advertisement results.
Explanation
Correct Answer
D:Centralized control policy influences the routes accepted and distributed by Controllers, controlling overlay reachability without carrying user payloads. Evidence for this policy-change production incident should include: Inspect received and advertised OMP routes at Controllers and affected edges; verify excluded prefixes are absent where prohibited.
Incorrect Answers
A:That option concerns regional internet breakout. Centralized control policy influences the routes accepted and distributed by Controllers, controlling overlay reachability without carrying user payloads.
B:That option concerns site-list targeting in centralized policy, not the requirement in this case. Its distinction is that Centralized control policy influences the routes accepted and distributed by Controllers, controlling overlay reachability without carrying user payloads.
C:That option concerns direct internet access policy and nat. Centralized control policy influences the routes accepted and distributed by Controllers, controlling overlay reachability without carrying user payloads. That mechanism is chiefly relevant to a different direct internet access policy and nat problem: Guest browsing must exit at the branch internet circuit rather than hairpin through the corporate data center.
Question 189
[SD-WAN architecture design review] An enterprise WAN design board is assessing a planned topology before deploying new branches. A branch behind broadband NAT can reach public DNS, but it has not learned the controller addresses required to initiate its secure fabric connections. Choose the mechanism that actually addresses the stated condition, not a merely adjacent SD-WAN feature. Which design or operational mistake would most directly defeat the intended outcome?
- Assuming the Manager forwards the first orchestration handshake leaves the branch without its actual controller discovery mechanism.
- A learned service prefix with no resolvable active TLOC does not by itself prove that a data tunnel can carry traffic.
- Assuming that a colocation connection automatically inspects all branch traffic ignores service steering requirements.
- Assuming OMP route reception itself constitutes application-payload encryption skips the actual tunnel validation.
Explanation
Correct Answer
A:Assuming the Manager forwards the first orchestration handshake leaves the branch without its actual controller discovery mechanism. This mistake undermines the intended sd-wan validator orchestration and nat discovery requirement. The supported correction is Configure reachable SD-WAN Validator discovery and verify the branch can establish its initial authenticated orchestration connection, and the independent evidence to seek is Confirm initial Validator control connectivity and discovery of Manager and Controller addresses along with the observed NAT mapping at the branch.
Incorrect Answers
B:That failure mode is primarily about omp vroute versus transport location instead of this required sd-wan validator orchestration and nat discovery treatment. For this case, the principal failure mode is Assuming the Manager forwards the first orchestration handshake leaves the branch without its actual controller discovery mechanism.
C:That failure mode is primarily about cloud onramp colocation service chaining instead of this required sd-wan validator orchestration and nat discovery treatment. For this case, the principal failure mode is Assuming the Manager forwards the first orchestration handshake leaves the branch without its actual controller discovery mechanism.
D:That failure mode is primarily about data-plane encrypted overlay forwarding instead of this required sd-wan validator orchestration and nat discovery treatment.
Question 190
[Controller connectivity incident] An on-call engineer must restore the exact controller or fabric identity behavior without changing unrelated service routes. Controller control sessions drop only when branches switch to a new ISP, despite unchanged certificates and organization identity. The fix must preserve unrelated security, transport and service-VPN behavior and be confirmed by observable evidence. Which supported action best addresses this requirement?
- Inspect control-connection diagnostics and Controller identity/reachability before changing service-VPN routing policies.
- Compare new-ISP underlay addresses, NAT behavior, transport policy and controller reachability before changing certificates.
- Distribute redundant controller resources across independent failure domains and validate separate transport paths.
- Inspect Validator name resolution and reachability, NAT mapping, and permitted initial control transport as the first onboarding stage.
Explanation
Correct Answer
B:An ISP migration can alter NAT and route paths while leaving the PKI untouched; isolate the transport change first. Evidence for this controller connectivity incident should include: Verify source WAN transport, DNS, NAT mappings, reachable controller endpoints, and restoration after policy correction.
Incorrect Answers
A:That option concerns troubleshooting control peer state. An ISP migration can alter NAT and route paths while leaving the PKI untouched; isolate the transport change first. Inspect control-connection diagnostics and Controller identity/reachability before changing service-VPN routing policies.
C:That option concerns disaster-recovery control-site isolation. An ISP migration can alter NAT and route paths while leaving the PKI untouched; isolate the transport change first. That mechanism is chiefly relevant to a different disaster-recovery control-site isolation problem: Two control VMs share the same hypervisor and uplink while the stated requirement is resilience to host and connectivity failure.
D:That option concerns validator discovery and nat traversal. An ISP migration can alter NAT and route paths while leaving the PKI untouched; isolate the transport change first.