Juniper JN0-452 Practice Test 94
Question 930
Which acceptance evidence would show that the original fault or risk was actually remediated? A controller-migrated SSID still tunnels guest traffic to an unavailable old gateway even after its new Mist AP shows online. Select the ONE best answer.
- The reclassified endpoint accesses only its newly approved services and retains a traceable policy history.
- Guest stations resolve addresses and reach approved internet resources through the documented post-migration path.
- A new unmanaged client completes permitted DNS and portal authentication without granting broad pre-auth access.
- Partners authenticate to one intended SSID but traffic between separate partner groups is denied.
Explanation
Correct Answer
B:It validates the controlled change: Inspect the effective WLAN forwarding mode and update its permitted tunnel or local bridge design under controlled cutover.
Incorrect Answers
A:The alternative observation is: The reclassified endpoint accesses only its newly approved services and retains a traceable policy history. The acceptance test for this case is: Guest stations resolve addresses and reach approved internet resources through the documented post-migration path.
C:A captive admission process can deadlock if services necessary to reach the portal are blocked until the portal succeeds. This is a different acceptance outcome; the required result here is: Guest stations resolve addresses and reach approved internet resources through the documented post-migration path.
D:Per-key identity differentiation can support group isolation without multiplying SSIDs for each partner when configured correctly. This is a different acceptance outcome; the required result here is: Guest stations resolve addresses and reach approved internet resources through the documented post-migration path.
Question 931
After the authorized change, which measurable result most directly demonstrates success? An administrator reviews only the most recent hour of SLE data for a problem that occurs once weekly after automated backup traffic peaks. Select the ONE best answer.
- The correct AP and time-bounded call issue appear in the SLE timeline, supporting a targeted repair.
- The critical window shows uninterrupted association, and the authorized RRM update completes in the approved interval.
- The weekly failure can be reproduced and disappears after the verified capacity or scheduling correction.
- Channel changes comply with region rules and the affected clients recover service within approved interruption targets.
Explanation
Correct Answer
C:It validates the controlled change: Expand the observation window and correlate recurring capacity degradation with upstream traffic and scheduled workloads.
Incorrect Answers
A:Identical SSID strings across locations do not identify the underlying physical client-serving radio or correct analytics population. This is a different acceptance outcome; the required result here is: The weekly failure can be reproduced and disappears after the verified capacity or scheduling correction.
B:An otherwise valid radio optimization can be operationally harmful if it interrupts sensitive client sessions. This is a different acceptance outcome; the required result here is: The weekly failure can be reproduced and disappears after the verified capacity or scheduling correction.
D:DFS requirements can force spectrum changes independently of user traffic volume or AP physical health. This is a different acceptance outcome; the required result here is: The weekly failure can be reproduced and disappears after the verified capacity or scheduling correction.
Question 932
Which specific remediation is the best controlled next step? A corporate WLAN migrates to WPA3-Enterprise but a legacy scanner cannot negotiate the required association security suite. Select the ONE best answer.
- Corroborate suspected rogue status with wired-network attachment and authorized inventory before taking enforcement action.
- Adopt supported distinct per-user or per-device PSKs or enterprise identity credentials with individual revocation controls.
- Inventory device security support and provide a documented segregated alternative or approved replacement without weakening the corporate WLAN.
- Inspect the effective WLAN forwarding mode and update its permitted tunnel or local bridge design under controlled cutover.
Explanation
Correct Answer
C:Acceptance criterion: Eligible employees join with the intended protected mode while legacy exceptions remain restricted and audited. Before making it, verify: Review RSN advertised AKMs, PMF requirements, client drivers, EAP logs and WLAN authentication failures.
Incorrect Answers
A:Corroborate suspected rogue status with wired-network attachment and authorized inventory before taking enforcement action. Here the decisive dependency is: WPA3-Enterprise security capabilities and client support must align before an enterprise authentication exchange succeeds. Use the specified intervention: Inventory device security support and provide a documented segregated alternative or approved replacement without weakening the corporate WLAN.
B:Adopt supported distinct per-user or per-device PSKs or enterprise identity credentials with individual revocation controls. Here the decisive dependency is: WPA3-Enterprise security capabilities and client support must align before an enterprise authentication exchange succeeds. Use the specified intervention: Inventory device security support and provide a documented segregated alternative or approved replacement without weakening the corporate WLAN.
D:That option would inspect the effective WLAN forwarding mode and update its permitted tunnel or local bridge design under controlled cutover, but it addresses a different concern. WPA3-Enterprise security capabilities and client support must align before an enterprise authentication exchange succeeds.
Question 933
Which evidence-gathering check most directly narrows the cause of this incident? An indoor venue assumes vBLE can provide sub-meter accuracy everywhere, including a metal elevator lobby, without a site survey. Select the ONE best answer.
- Compare glass geometry, RSSI scatter, surveyed route positions, receiver placements and location confidence.
- Compare AP serial-to-coordinate map, moved hardware positions, reference tags, RSSI history and measured location errors.
- Inspect device identity rules, consented app sessions, duplicated devices, coverage gaps and counting methodology.
- Inspect reference marker coordinates, AP density, elevator construction, observation scatter and error percentiles.
Explanation
Correct Answer
D:Set realistic precision targets and validate position variance at representative RF-obstructed locations before deployment acceptance.
Incorrect Answers
A:Survey affected storefront geometry and refine receiver placement or supported calibration based on measured multipath effects. The focused check for the reported condition is: Inspect reference marker coordinates, AP density, elevator construction, observation scatter and error percentiles.
B:A location engine depends on accurate transmitter or receiver geometry; device movement can invalidate historic map assumptions. The focused check for the reported condition is: Inspect reference marker coordinates, AP density, elevator construction, observation scatter and error percentiles.
C:One person may have multiple radios while some people advertise none; radio counts are not inherently verified human counts. The focused check for the reported condition is: Inspect reference marker coordinates, AP density, elevator construction, observation scatter and error percentiles.
Question 934
Which end-to-end operational sequence best controls risk from detection through acceptance? A site sets a vBLE engagement zone right against an adjoining tenant's wall and visitors receive prompts while shopping next door. Select the ONE best answer.
- Investigate: Inspect wall attenuation, receiver positions, app trigger logs, reference routes and property boundary plans. Remediate: Conduct boundary walks and adjust beacon placement, zone definition and permitted engagement scope to prevent cross-tenant notifications. Verify: Opted-in test devices in the target area receive correct messages while adjacent-tenant walks produce none.
- Investigate: Review original privacy purpose, user notices, role access, secondary reporting and retention rules. Remediate: Perform a purpose and privacy assessment before any secondary identifiable use and restrict data sharing to authorized processing. Verify: Only authorized uses access scoped location records and unsupported secondary reports cannot be generated.
- Investigate: Compare AP serial-to-coordinate map, moved hardware positions, reference tags, RSSI history and measured location errors. Remediate: Update verified AP physical positions and the site map before recalibrating and testing location estimates in the modified layout. Verify: Representative tracked carts appear in their actual aisles after a measured walk test and no false neighboring-zone alarms remain.
- Investigate: Inspect raw location jitter, crossing timestamps, dwell rules, zone geometry and repeated controlled walks. Remediate: Use supported dwell or stability criteria and validate zone hysteresis while preserving legitimate entry and exit detection. Verify: One legitimate entry generates the expected notification and stationary boundary testing causes no alert flood.
Explanation
Correct Answer
A:Radio coverage can extend past contractual or physical property boundaries even if a floorplan icon appears contained. Inspect wall attenuation, receiver positions, app trigger logs, reference routes and property boundary plans.
Incorrect Answers
B:Review original privacy purpose, user notices, role access, secondary reporting and retention rules. Remediate: Perform a purpose and privacy assessment before any secondary identifiable use and restrict data sharing to authorized processing. Verify: Only authorized uses access scoped location records and unsupported secondary reports cannot be generated. These steps address a different operational problem. They do not connect diagnosis, correction and acceptance criteria for the current requirement. The required change is: Conduct boundary walks and adjust beacon placement, zone definition and permitted engagement scope to prevent cross-tenant notifications.
C:Compare AP serial-to-coordinate map, moved hardware positions, reference tags, RSSI history and measured location errors. Remediate: Update verified AP physical positions and the site map before recalibrating and testing location estimates in the modified layout. Verify: Representative tracked carts appear in their actual aisles after a measured walk test and no false neighboring-zone alarms remain. These steps address a different operational problem. They do not connect diagnosis, correction and acceptance criteria for the current requirement. The required change is: Conduct boundary walks and adjust beacon placement, zone definition and permitted engagement scope to prevent cross-tenant notifications.
D:Inspect raw location jitter, crossing timestamps, dwell rules, zone geometry and repeated controlled walks. Remediate: Use supported dwell or stability criteria and validate zone hysteresis while preserving legitimate entry and exit detection. Verify: One legitimate entry generates the expected notification and stationary boundary testing causes no alert flood. These steps address a different operational problem. They do not connect diagnosis, correction and acceptance criteria for the current requirement. The required change is: Conduct boundary walks and adjust beacon placement, zone definition and permitted engagement scope to prevent cross-tenant notifications.
Question 935
Which action directly resolves the core infrastructure requirement without relying on an unrelated workaround? A new laptop supports 160 MHz width but all neighboring sites must use narrow reuse channels in a highly occupied office building. Select the ONE best answer.
- Examine rate adaptation against SNR, interference and retransmissions, then address the RF cause rather than IP configuration.
- Balance link peak rate against available unoccupied spectrum and competing cells using an RF capacity assessment.
- Recalculate the link budget in decibels and compare the predicted signal reduction against verified receive sensitivity margins.
- Validate applicable WMM access categories and voice QoS markings across WLAN and switching without granting unrestricted priority.
Explanation
Correct Answer
B:A wider PHY configuration is not automatically the best network-level throughput choice in highly congested spectrum. This is the targeted change for the reported environment.
Incorrect Answers
A:Examine rate adaptation against SNR, interference and retransmissions, then address the RF cause rather than IP configuration. Here the decisive dependency is: A wider PHY configuration is not automatically the best network-level throughput choice in highly congested spectrum. Use the specified intervention: Balance link peak rate against available unoccupied spectrum and competing cells using an RF capacity assessment.
C:Recalculate the link budget in decibels and compare the predicted signal reduction against verified receive sensitivity margins. Here the decisive dependency is: A wider PHY configuration is not automatically the best network-level throughput choice in highly congested spectrum. Use the specified intervention: Balance link peak rate against available unoccupied spectrum and competing cells using an RF capacity assessment.
D:That option would validate applicable WMM access categories and voice QoS markings across WLAN and switching without granting unrestricted priority, but it addresses a different concern. A wider PHY configuration is not automatically the best network-level throughput choice in highly congested spectrum.
Question 936
The operator needs proof rather than a guess. Which investigation should come first? A shared staff WLAN uses a portal login as the only access condition while devices retain unrestricted LAN access before the portal loads. Select the ONE best answer.
- Test pre-auth ARP, gateway and DNS reachability, portal transition and effective WxLAN policies.
- Review client classification, tags, policy lookup, rule matches and before-after traffic authorization.
- Inspect guest DNS flow, resolver policy, portal FQDN resolution and pre-auth ACL events.
- Inspect device identity, effective WxLAN roles, destination policy decisions and denial logs.
Explanation
Correct Answer
A:Test pre-auth ARP, gateway and DNS reachability, portal transition and effective WxLAN policies. This observation directly isolates the suspected dependency before a risky change.
Incorrect Answers
B:Security policies apply based on evaluated identity and classification; a correct rule is irrelevant if no clients match it. The focused check for the reported condition is: Test pre-auth ARP, gateway and DNS reachability, portal transition and effective WxLAN policies.
C:A captive admission process can deadlock if services necessary to reach the portal are blocked until the portal succeeds. The focused check for the reported condition is: Test pre-auth ARP, gateway and DNS reachability, portal transition and effective WxLAN policies.
D:Authentication establishes possession of a credential, whereas WxLAN authorization defines the network resources that identity may reach. The focused check for the reported condition is: Test pre-auth ARP, gateway and DNS reachability, portal transition and effective WxLAN policies.
Question 937
Which specific remediation is the best controlled next step? A factory asset tag is reliably detected in one aisle but becomes invisible after forklifts stack large steel containers next to the original receiver. Select the ONE best answer.
- Reconcile unique tag identity with authorized site assignment and validate both receiver location and cloud tenant scope.
- Perform a purpose and privacy assessment before any secondary identifiable use and restrict data sharing to authorized processing.
- Distinguish associated client devices, BLE tags and explicitly consented visitor app sessions before computing population metrics.
- Reassess receiver line of sight and physical attenuation under actual operating layouts and adjust supported coverage accordingly.
Explanation
Correct Answer
D:Variable metallic obstacles can shadow low-power radio tags and alter the set of receivers that detect them. Acceptance criterion: The affected tag is detected through representative stock configurations with documented coverage limits.
Incorrect Answers
A:Reconcile unique tag identity with authorized site assignment and validate both receiver location and cloud tenant scope. Here the decisive dependency is: Variable metallic obstacles can shadow low-power radio tags and alter the set of receivers that detect them. Use the specified intervention: Reassess receiver line of sight and physical attenuation under actual operating layouts and adjust supported coverage accordingly.
B:Perform a purpose and privacy assessment before any secondary identifiable use and restrict data sharing to authorized processing. Here the decisive dependency is: Variable metallic obstacles can shadow low-power radio tags and alter the set of receivers that detect them. Use the specified intervention: Reassess receiver line of sight and physical attenuation under actual operating layouts and adjust supported coverage accordingly.
C:Distinguish associated client devices, BLE tags and explicitly consented visitor app sessions before computing population metrics. Here the decisive dependency is: Variable metallic obstacles can shadow low-power radio tags and alter the set of receivers that detect them. Use the specified intervention: Reassess receiver line of sight and physical attenuation under actual operating layouts and adjust supported coverage accordingly.
Question 938
The operator needs proof rather than a guess. Which investigation should come first? A junior analyst confuses proactive Marvis Actions with user-triggered Marvis queries and expects the same trigger and evaluation logic. Select the ONE best answer.
- Review action scope, correlated branch times, common services, AP inventory and site-specific SLE trends.
- Review AP last-seen, action timestamps, WAN health, current configuration and new client measurements.
- Inspect query time range, client first-seen, association events, recorded roaming activity and site timezone.
- Inspect action histories, query audit, detected conditions, supporting telemetry and notification timing.
Explanation
Correct Answer
D:Proactive findings can be surfaced without a new user question while reactive queries investigate a requested scope. Distinguish evidence-led proactive detection from reactive natural-language investigation and select the right workflow for each.
Incorrect Answers
A:Cross-site correlated symptoms may share identity, WAN or cloud dependencies rather than an isolated failing AP. The focused check for the reported condition is: Inspect action histories, query audit, detected conditions, supporting telemetry and notification timing.
B:Review AP last-seen, action timestamps, WAN health, current configuration and new client measurements. The focused check for the reported condition is: Inspect action histories, query audit, detected conditions, supporting telemetry and notification timing.
C:An empty historical query does not prove that a later client roaming incident never occurred. The focused check for the reported condition is: Inspect action histories, query audit, detected conditions, supporting telemetry and notification timing.
Question 939
The operator needs proof rather than a guess. Which investigation should come first? A WAN team places the cloud management allowlist into a rule that blocks required TLS destinations but permits pings to public DNS. Select the ONE best answer.
- Compare AP label assignments, WLAN object targets, site ID and applied configuration status.
- Inspect object IDs, parent and site bindings, effective WLAN config, audit history and client RSN beacons.
- Inspect firewall denies, DNS endpoint resolution, TLS session failures, regional service URLs and last-seen events.
- Inspect tunnel endpoint addresses, transport reachability, session state, VLAN mapping and traffic captures.
Explanation
Correct Answer
C:ICMP or generic internet reachability does not establish an AP's ability to authenticate to all needed cloud services. Test the documented management control-plane endpoint reachability over the actual permitted ports and restore required egress.
Incorrect Answers
A:Label-based targeting affects which wireless configuration objects apply even when the AP has correct site ownership. The focused check for the reported condition is: Inspect firewall denies, DNS endpoint resolution, TLS session failures, regional service URLs and last-seen events.
B:Object naming alone does not establish which configuration scope wins, and overlapping policies can create unintended WLAN behavior. The focused check for the reported condition is: Inspect firewall denies, DNS endpoint resolution, TLS session failures, regional service URLs and last-seen events.
D:A tunneled WLAN depends on end-to-end transport and compatible gateway reachability in addition to AP-cloud management health. The focused check for the reported condition is: Inspect firewall denies, DNS endpoint resolution, TLS session failures, regional service URLs and last-seen events.
Question 940
The operator needs proof rather than a guess. Which investigation should come first? A multi-AP deployment disables protected management frame support because an older test handset complains during WPA3 onboarding. Select the ONE best answer.
- Review channel allocations, overlap maps, airtime busy time, client throughput and density.
- Inspect 802.11v BTM request and response frames, candidate lists and client roaming behavior.
- Examine overlapping BSSIDs, AP channel reuse, CCA busy time, client distribution and contention behavior.
- Inspect advertised RSN capabilities, PMF negotiation, handset software support and association rejection logs.
Explanation
Correct Answer
D:WPA3 security negotiation includes management-frame protection obligations that cannot simply be removed from the protected WLAN. Identify legacy handset compatibility and provide a controlled supported access alternative while retaining required WPA3 protections.
Incorrect Answers
A:Wider channels increase theoretical peak rate but can reduce reuse and raise contention in dense multi-AP spaces. The focused check for the reported condition is: Inspect advertised RSN capabilities, PMF negotiation, handset software support and association rejection logs.
B:Interpret supported BSS transition management as a steering suggestion and validate client response and RF alternatives. The focused check for the reported condition is: Inspect advertised RSN capabilities, PMF negotiation, handset software support and association rejection logs.
C:Rebalance channel reuse and AP power with measured contention and capacity rather than adding radios on the same channel. The focused check for the reported condition is: Inspect advertised RSN capabilities, PMF negotiation, handset software support and association rejection logs.