Juniper JN0-452 Practice Test 112
Question 1110
A change engineer must select a justified corrective intervention. Which should be approved? A remote office loses many voice frames when another client starts large file transfers using identical wireless access priorities. Select the ONE best answer.
- Compare signal strength against measured noise floor and interference before changing power or AP placement.
- Assess bidirectional link budget and adjust AP placement or supported power design to preserve client uplink reachability.
- Validate applicable WMM access categories and voice QoS markings across WLAN and switching without granting unrestricted priority.
- Trace beacon discovery, 802.11 authentication and association, EAP exchange and DHCP as distinct service stages.
Explanation
Correct Answer
C:EDCA access categories bias contention opportunities, but incorrect classification can leave delay-sensitive voice behind bulk traffic. Before making it, verify: Inspect WMM enabled state, DSCP-to-AC mapping, queue statistics, contention timing and call traces.
Incorrect Answers
A:That option would compare signal strength against measured noise floor and interference before changing power or AP placement, but it addresses a different concern. EDCA access categories bias contention opportunities, but incorrect classification can leave delay-sensitive voice behind bulk traffic.
B:Assess bidirectional link budget and adjust AP placement or supported power design to preserve client uplink reachability. Here the decisive dependency is: EDCA access categories bias contention opportunities, but incorrect classification can leave delay-sensitive voice behind bulk traffic. Use the specified intervention: Validate applicable WMM access categories and voice QoS markings across WLAN and switching without granting unrestricted priority.
D:That option would trace beacon discovery, 802.11 authentication and association, EAP exchange and DHCP as distinct service stages, but it addresses a different concern. EDCA access categories bias contention opportunities, but incorrect classification can leave delay-sensitive voice behind bulk traffic.
Question 1111
Which evidence-gathering check most directly narrows the cause of this incident? Marvis identifies a suspected authentication-server dependency but no one has checked whether the RADIUS server actually rejected credentials. Select the ONE best answer.
- Inspect RADIUS accept/reject/timeout, EAP stage, identity server health and Marvis-linked session timeline.
- Inspect Action time range, client join bursts, DHCP utilization, relay messages and morning SLE trends.
- Compare applied config revision, Action timestamps, new session events, SLE recovery and client test logs.
- Inspect Mini identity scope, actual directory and RADIUS principals, access rules and synthetic session records.
Explanation
Correct Answer
A:Inspect RADIUS accept/reject/timeout, EAP stage, identity server health and Marvis-linked session timeline. This observation directly isolates the suspected dependency before a risky change. AI troubleshooting suggestions are hypotheses grounded in telemetry, not substitutes for direct control-plane evidence. The appropriate intervention is: Validate the assistant's hypothesis against EAP response codes, RADIUS server logs and network reachability.
Incorrect Answers
B:Time-bounded and cyclical service defects can be obscured when AI evidence is reviewed outside the relevant interval. The focused check for the reported condition is: Inspect RADIUS accept/reject/timeout, EAP stage, identity server health and Marvis-linked session timeline.
C:Action lifecycle can depend on subsequent observed service metrics rather than immediate disappearance after a configuration write. The focused check for the reported condition is: Inspect RADIUS accept/reject/timeout, EAP stage, identity server health and Marvis-linked session timeline.
D:Keep synthetic telemetry and production identity sources separate and authorize only verified real user or device records. The focused check for the reported condition is: Inspect RADIUS accept/reject/timeout, EAP stage, identity server health and Marvis-linked session timeline.
Question 1112
Which specific remediation is the best controlled next step? A site reports degraded coverage SLE after construction but APs show no hardware alarms or firmware faults. Select the ONE best answer.
- Map affected-client RSSI and noise histories to new physical obstructions and perform a verified placement or RF adjustment.
- Distinguish internal Wireless Assurance targets from contractually agreed SLAs and document their population and measurement rules.
- Drill into classifier-level roaming insights and identify source and destination BSSIDs for the affected client population.
- Verify authentication-related SLEs and AAA service state separately from AP control-plane recovery.
Explanation
Correct Answer
A:Before making it, verify: Inspect coverage SLE, client location, postconstruction maps, RSSI and SNR trends, AP placement and retries.
Incorrect Answers
B:Distinguish internal Wireless Assurance targets from contractually agreed SLAs and document their population and measurement rules. Here the decisive dependency is: Construction and RF attenuation can degrade user coverage even with fully functioning AP hardware. Use the specified intervention: Map affected-client RSSI and noise histories to new physical obstructions and perform a verified placement or RF adjustment.
C:Drill into classifier-level roaming insights and identify source and destination BSSIDs for the affected client population. Here the decisive dependency is: Construction and RF attenuation can degrade user coverage even with fully functioning AP hardware. Use the specified intervention: Map affected-client RSSI and noise histories to new physical obstructions and perform a verified placement or RF adjustment.
D:That option would verify authentication-related SLEs and AAA service state separately from AP control-plane recovery, but it addresses a different concern. Construction and RF attenuation can degrade user coverage even with fully functioning AP hardware.
Question 1113
Which cause-and-effect relationship is most relevant to the described operational risk? An AP group near a conference hall provides enough signal but large frames are frequently retried during occasional burst interference. Select the ONE best answer.
- Transient interference can increase corruption and retries even when average RSSI appears sufficient.
- Decibel units are logarithmic; changes in loss can meaningfully alter the usable link margin and modulation selection.
- Reflections and destructive interference can produce local fading that a two-dimensional proximity map omits.
- OFDMA scheduling depends on supported 802.11ax operation and suitable traffic conditions, not the SSID label alone.
Explanation
Correct Answer
A:The corresponding supported intervention is: Correlate packet error and airtime events with local spectrum disturbances before tuning channel, width or protection options.
Incorrect Answers
B:The alternative governing principle is: Decibel units are logarithmic; changes in loss can meaningfully alter the usable link margin and modulation selection. The mechanism tested by the reported case is: Transient interference can increase corruption and retries even when average RSSI appears sufficient.
C:The alternative governing principle is: Reflections and destructive interference can produce local fading that a two-dimensional proximity map omits. The mechanism tested by the reported case is: Transient interference can increase corruption and retries even when average RSSI appears sufficient.
D:The alternative governing principle is: OFDMA scheduling depends on supported 802.11ax operation and suitable traffic conditions, not the SSID label alone. The mechanism tested by the reported case is: Transient interference can increase corruption and retries even when average RSSI appears sufficient.
Question 1114
Select TWO appropriate investigation, change, and acceptance elements for this situation. A radio resource manager plans to raise AP transmit power in an area where high client retries stem from contention with neighboring cells.
- Narrow the SLE window to the reported business interval and analyze coverage, capacity and client participation separately.
- Inspect neighboring BSS airtime, AP power, client roam behavior, RF survey and collision counters.
- Analyze the effect of channel reuse and cell overlap before choosing supported localized power adjustments.
- Force maximum radio power across the site to eliminate contention independent of channel plan.
- Review roam transition timestamps, candidate BSSIDs, EAP exchange, RSSI overlap and drop-event classifications.
Explanation
Correct Answer
B:Increasing EIRP can expand contention domains and worsen sticky-client or co-channel behavior rather than resolve busy airtime. Analyze the effect of channel reuse and cell overlap before choosing supported localized power adjustments. This check separates the suspected dependency before a risky change.
C:Increasing EIRP can expand contention domains and worsen sticky-client or co-channel behavior rather than resolve busy airtime. Before making it, verify: Inspect neighboring BSS airtime, AP power, client roam behavior, RF survey and collision counters.
Incorrect Answers
A:Narrow the SLE window to the reported business interval and analyze coverage, capacity and client participation separately. This action belongs to a different situation: A retail store's client-experience report averages an overnight quiet period with a short, severe lunch-hour coverage incident. Here the decisive dependency is: Increasing EIRP can expand contention domains and worsen sticky-client or co-channel behavior rather than resolve busy airtime. Use the specified intervention: Analyze the effect of channel reuse and cell overlap before choosing supported localized power adjustments.
D:Force maximum radio power across the site to eliminate contention independent of channel plan. This shortcut skips or undermines the needed control. Increasing EIRP can expand contention domains and worsen sticky-client or co-channel behavior rather than resolve busy airtime. The required remediation is: Analyze the effect of channel reuse and cell overlap before choosing supported localized power adjustments.
E:This check investigates a different symptom (A medical device fleet loses connectivity during moves between floors although association SLE at each stationary test point is high.). For this incident, the targeted check is: Inspect neighboring BSS airtime, AP power, client roam behavior, RF survey and collision counters.
Question 1115
After the authorized change, which measurable result most directly demonstrates success? An asset is transferred to another branch, but its location history remains bound to the original Mist site identifier. Select the ONE best answer.
- The destination site displays fresh tracked positions and the former site's viewers lose unauthorized active visibility.
- A measured route falls within a stated error distribution and the interface does not imply untested pinpoint accuracy.
- One permitted message appears during the intended visit and repeated crossings stay within the approved notification policy.
- Controlled test pallets stay assigned to the correct room with a documented false-location rate.
Explanation
Correct Answer
A:Cloud organization/site mapping can constrain where asset telemetry is interpreted and shown after physical relocation. It validates the controlled change: Update supported site and inventory association and validate receiving-site observations and authorized visibility.
Incorrect Answers
B:Received beacon strength alone can vary from reflection and orientation, making individual-position estimates uncertain. This is a different acceptance outcome; the required result here is: The destination site displays fresh tracked positions and the former site's viewers lose unauthorized active visibility.
C:An entry event can occur repeatedly for one visitor and requires product-level state or rate policy to avoid spamming. This is a different acceptance outcome; the required result here is: The destination site displays fresh tracked positions and the former site's viewers lose unauthorized active visibility.
D:Radio reception through a wall does not prove an object is in the same physical room as the strongest receiving AP. This is a different acceptance outcome; the required result here is: The destination site displays fresh tracked positions and the former site's viewers lose unauthorized active visibility.
Question 1116
Which end-to-end operational sequence best controls risk from detection through acceptance? An operator exports packet captures from multiple APs but their unsynchronized timestamps lead to an incorrect conclusion about packet order. Select the ONE best answer.
- Investigate: Inspect RRM recommendations, channel overlap, AP density, power levels, SNR and retry measurements. Remediate: Assess RRM evidence, co-channel contention and per-radio channel reuse before making any localized power or channel change. Verify: A limited RRM adjustment reduces busy-airtime collision and improves throughput for affected clients without neighbor degradation.
- Investigate: Compare SLE configuration, customer SLA definitions, measurement units, exclusion rules and observed failure interval. Remediate: Distinguish internal Wireless Assurance targets from contractually agreed SLAs and document their population and measurement rules. Verify: Reports explicitly label operational SLE performance and any formal contractual calculation can be independently reproduced.
- Investigate: Inspect UTC timestamps, NTP state, AP clocks, capture offsets and matching sequence identifiers. Remediate: Normalize capture and event times to verified sources and record any clock offsets before cross-device causality analysis. Verify: The reconstructed wireless exchange orders association, EAP and forwarding stages consistently across APs.
- Investigate: Inspect channel occupancy, interferer onset, RRM trigger history, spectrum signatures and SLE timeline. Remediate: Compare spectrum interference timeline and RRM decisions to identify whether channel movement was a response or the root cause. Verify: A controlled event confirms the interferer and the corrected channel plan maintains acceptable client experience.
Explanation
Correct Answer
C:Inspect UTC timestamps, NTP state, AP clocks, capture offsets and matching sequence identifiers. Remediate: Normalize capture and event times to verified sources and record any clock offsets before cross-device causality analysis. Verify: The reconstructed wireless exchange orders association, EAP and forwarding stages consistently across APs. The diagnostic identifies the actual constraint, the intervention addresses its cause, and verification proves the relevant outcome. Packet timing comparisons require consistent time context across captures and cloud event streams.
Incorrect Answers
A:Inspect RRM recommendations, channel overlap, AP density, power levels, SNR and retry measurements. Remediate: Assess RRM evidence, co-channel contention and per-radio channel reuse before making any localized power or channel change. Verify: A limited RRM adjustment reduces busy-airtime collision and improves throughput for affected clients without neighbor degradation. These steps address a different operational problem. They do not connect diagnosis, correction and acceptance criteria for the current requirement. The required change is: Normalize capture and event times to verified sources and record any clock offsets before cross-device causality analysis.
B:Compare SLE configuration, customer SLA definitions, measurement units, exclusion rules and observed failure interval. Remediate: Distinguish internal Wireless Assurance targets from contractually agreed SLAs and document their population and measurement rules. Verify: Reports explicitly label operational SLE performance and any formal contractual calculation can be independently reproduced. These steps address a different operational problem. They do not connect diagnosis, correction and acceptance criteria for the current requirement. The required change is: Normalize capture and event times to verified sources and record any clock offsets before cross-device causality analysis.
D:Inspect channel occupancy, interferer onset, RRM trigger history, spectrum signatures and SLE timeline. Remediate: Compare spectrum interference timeline and RRM decisions to identify whether channel movement was a response or the root cause. Verify: A controlled event confirms the interferer and the corrected channel plan maintains acceptable client experience. These steps address a different operational problem. They do not connect diagnosis, correction and acceptance criteria for the current requirement. The required change is: Normalize capture and event times to verified sources and record any clock offsets before cross-device causality analysis.
Question 1117
Before changing production, which focused diagnostic is most useful for identifying the true dependency? A shopping complex transfers several BLE tags between locations and attempts to infer which site owns a tag solely from its friendly description. Select the ONE best answer.
- Inspect reference marker coordinates, AP density, elevator construction, observation scatter and error percentiles.
- Inspect tag serial, BLE advertised identity, site transfer record, access rights and observation history.
- Inspect raw location jitter, crossing timestamps, dwell rules, zone geometry and repeated controlled walks.
- Inspect UTC timestamps, site timezone, daylight changes, receiver clock and event records.
Explanation
Correct Answer
B:Friendly asset labels can be reused while actual tag identifiers and site ownership determine legitimate location data. Reconcile unique tag identity with authorized site assignment and validate both receiver location and cloud tenant scope. This check separates the suspected dependency before a risky change.
Incorrect Answers
A:Set realistic precision targets and validate position variance at representative RF-obstructed locations before deployment acceptance. The focused check for the reported condition is: Inspect tag serial, BLE advertised identity, site transfer record, access rights and observation history.
C:Position jitter near a boundary can produce repeated false transitions without actual movement across the intended area. The focused check for the reported condition is: Inspect tag serial, BLE advertised identity, site transfer record, access rights and observation history.
D:Normalize source event times to a consistent reference and retain local display offset separately from recorded occurrence. The focused check for the reported condition is: Inspect tag serial, BLE advertised identity, site transfer record, access rights and observation history.
Question 1118
Which specific remediation is the best controlled next step? A help-desk technician asks Marvis why a wireless phone disconnected but supplies only a generic building name shared by many sites. Select the ONE best answer.
- Use synthetic and observed client evidence for diagnosis while requiring authorized change control for identity policy remediation.
- Scope the Marvis query to the verified client identifier, site and incident time and inspect related client events.
- Correlate supported session and identity data while acknowledging MAC randomization and avoid attributing unrelated devices.
- Refresh device state and event freshness and check site connectivity before applying live changes based on stale action data.
Explanation
Correct Answer
B:Natural-language troubleshooting needs a precise device and observation context to distinguish relevant evidence from unrelated sessions. Before making it, verify: Verify client MAC, site ID, question scope, disconnect timestamp, Marvis query result and linked event history.
Incorrect Answers
A:That option would use synthetic and observed client evidence for diagnosis while requiring authorized change control for identity policy remediation, but it addresses a different concern. Natural-language troubleshooting needs a precise device and observation context to distinguish relevant evidence from unrelated sessions.
C:Correlate supported session and identity data while acknowledging MAC randomization and avoid attributing unrelated devices. Here the decisive dependency is: Natural-language troubleshooting needs a precise device and observation context to distinguish relevant evidence from unrelated sessions. Use the specified intervention: Scope the Marvis query to the verified client identifier, site and incident time and inspect related client events.
D:Refresh device state and event freshness and check site connectivity before applying live changes based on stale action data. Here the decisive dependency is: Natural-language troubleshooting needs a precise device and observation context to distinguish relevant evidence from unrelated sessions. Use the specified intervention: Scope the Marvis query to the verified client identifier, site and incident time and inspect related client events.
Question 1119
Select TWO appropriate investigation, change, and acceptance elements for this situation. A site adds a second Mist Edge instance for resilience but both instances share a single failed upstream connectivity link.
- Identify common transport dependencies and design supported redundant gateways and reachability across independent paths.
- Inspect claim errors, prior tenant ownership, serial records, support authorization and transfer audit history.
- Map the chosen forwarding topology, gateway and network services before enabling the new WLAN in production.
- Count two virtual machines as resilient even when one upstream router disconnects both.
- Trace tunnel endpoints, gateway placement, WAN circuits, routing failover and recovery event logs.
Explanation
Correct Answer
A:Multiple virtual Edge instances cannot provide independent failover if their upstream service path shares one failure domain. Before making it, verify: Trace tunnel endpoints, gateway placement, WAN circuits, routing failover and recovery event logs.
E:Multiple virtual Edge instances cannot provide independent failover if their upstream service path shares one failure domain. Identify common transport dependencies and design supported redundant gateways and reachability across independent paths.
Incorrect Answers
B:This check investigates a different symptom (A customer attempts to claim an AP serial already attached to a former service provider's Mist organization.). For this incident, the targeted check is: Trace tunnel endpoints, gateway placement, WAN circuits, routing failover and recovery event logs.
C:That option would map the chosen forwarding topology, gateway and network services before enabling the new WLAN in production, but it addresses a different concern. Multiple virtual Edge instances cannot provide independent failover if their upstream service path shares one failure domain.
D:Count two virtual machines as resilient even when one upstream router disconnects both. This shortcut skips or undermines the needed control. Multiple virtual Edge instances cannot provide independent failover if their upstream service path shares one failure domain. The required remediation is: Identify common transport dependencies and design supported redundant gateways and reachability across independent paths.
Question 1120
Which specific remediation is the best controlled next step? A network engineer changes an organization-wide time zone and later misorders cloud audit events across branch offices. Select the ONE best answer.
- Check relevant forwarding interfaces and intended WLAN tunnel bindings separately from the management-plane health indicator.
- Inventory tenant-specific identity integrations, certificate trust, VLAN attachment and WLAN scope before replicating the configuration.
- Validate the Mist event subscription and webhook destination, authentication, TLS connectivity and receiver acknowledgment behavior.
- Normalize audit timestamps against a common reference and distinguish display time zone from event occurrence.
Explanation
Correct Answer
D:Before making it, verify: Review raw UTC events, time zone display options, device clocks and configuration history.
Incorrect Answers
A:That option would check relevant forwarding interfaces and intended WLAN tunnel bindings separately from the management-plane health indicator, but it addresses a different concern. Management-console time presentation does not change when a remote configuration change actually occurred.
B:Inventory tenant-specific identity integrations, certificate trust, VLAN attachment and WLAN scope before replicating the configuration. Here the decisive dependency is: Management-console time presentation does not change when a remote configuration change actually occurred. Use the specified intervention: Normalize audit timestamps against a common reference and distinguish display time zone from event occurrence.
C:That option would validate the Mist event subscription and webhook destination, authentication, TLS connectivity and receiver acknowledgment behavior, but it addresses a different concern. Management-console time presentation does not change when a remote configuration change actually occurred.